Search NASA⌕ Search

SEARCH · Search NASA

Results for “Finite Element Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Conduction Heat Transfer through Solid in Porous Materials: A Comparative Study by Finite-Element Simulations and Effective Medium Approximations

The development of insulation materials with low effective thermal conductivity is essential for energy savings in various applications, including buildings, food services, pipe insulation, and refrigeration. Such materials can be developed by using micro- or nanoporous structures, as well as low-thermal conductivity gases and/or reduced pressure. A variety of effective medium approximation (EMA) models have been developed to study thermal transport through solid in porous structures. However, in many cases, the impacts of porosity on solid conduction are not well predicted by EMA models because of the assumptions made for simplification. Furthermore, the results can vary by a factor of up to 1.5, depending on the morphology of the pores. Hence, proper guidance is needed to choose the appropriate EMA model for a given morphology. This work presents a finite element method study using COMSOL Multiphysics software for various geometries, including hollow cubes, overlapping hollow spheres (normally stacked and tightly packed), and Voronoi structures, and compares the results to those obtained from various EMA models. Simulation results for the hollow cubes and Voronoi structures matched well with the Maxwell-Eucken and Russell model. The results for hollow spheres closely matched the Bauer model and the Glicksman model with fitting parameters. This work provides guidance on analyzing and designing insulation materials for energy savings in the future.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Modeling deformation and failure in AlSi-polyester abradable sealcoating material using microstructure-based finite element simulation

A plasma-sprayed aluminum-silicon (AlSi)/polyester coating is applied in modern gas turbine engines as an abradable sealcoating to maintain tight clearances between the rotating blades and the static casing. While running the engine, the rotating blades “rub” with the abradable coating, which results in extreme strain rate (up to 10 6 ) dynamics and a high-temperature environment. Due to the difficulty of collecting direct measurements, predictive computational models are important for analyzing the deformation and failure of the abradable material, to help meet the design target of avoiding damage to the blade tip and maintaining high fuel efficiency. In this research, a microstructure-based finite element (FE) computational model was developed to capture the complex mechanical behavior of the AlSi/polyester microstructure. The model is based on a virtual representative-volume-element (RVE) of a metal-polymer microstructure, reconstructed from x-ray computed tomography. It models the plastic deformation of, and damage to, each AlSi and polyester constituents, as well as the failure at their interface. The model was calibrated and validated with uniaxial tension and compression experiments, conducted at two temperatures (298 K and 533 K) at an applied strain rate of 10 3 - 10 4 s -1 . The material exhibited strongly asymmetric tension-compression behavior and a sensitivity to temperature, which was well captured by the model. The model was further applied to investigate changes in mechanical behavior due to variations in constituents’ volume fractions, which provides guidance to the microstructural design of AlSi/polyester abradable materials. The model is expected to facilitate the development of improved abradable materials by bypassing the conventional trial-and-error approach and extensive testing requirements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2022

Design of Rigid-Flex PCB Robotics Leveraging Validated Finite Element Simulations

The use of rigid-flex printed circuit board (PCB) as primary structure has the potential to reduce the weight and volume of robotic systems. In the case of robotics for interplanetary exploration, these systems can leverage origamiinspired folding for increased mobility options and reduced storage volume. Folding rigid-flex PCB robotics can be constructed with rigid PCB connected by short Nomex fabric hinges coupled with flex PCB ribbon cables that permits enhanced system flexibility and energy dissipation to promote impact survivability. This paper presents a design methodology of rigidflex PCB systems with an emphasis on impact resistance. The design process considers solder joint adequacy, panel bending, and fracture using a finite element (FE) model. The proposed design methodology is developed using a case study with NASA JPL’s Pop-Up Folding Flat Explorer Robot (PUFFER). First, the finite-element (FE) modeling methodology is presented with consideration to both frequency and time-domain modeling applications, which include operational self-contact analysis and high impact scenarios. The time-domain impact modeling methodology utilizes hyperelastic material properties for the Nomex hinges. This modeling method is validated using image correlation of PUFFER drop tests. A flowchart is presented to guide users through a validated Abaqus modeling procedure for highly flexible rigid-flex systems. Next, a case study is presented in which PUFFER is subject to drop heights representative of falls into Lunar pits and then the design is refined for a more optimum impact performance. Finally, the results of the case study are used to inform a generalized design methodology for rigid-flex PCB robotics subject to high-impact loads with the considerations presented.

de la Croix, Jean-Pierre↗
NASA NTRS2022

Design of Rigid-Flex PCB Robotics Leveraging Validated Finite Element Simulations

The use of rigid-flex printed circuit board (PCB) as primary structure has the potential to reduce the weight and volume of robotic systems. In the case of robotics for interplanetary exploration, these systems can leverage origami-inspired folding for increased mobility options and reduced storage volume. Folding rigid-flex PCB robotics can be constructed with rigid PCB connected by short Nomex fabric hinges coupled with flex PCB ribbon cables that permits enhanced system flexibility and energy dissipation to promote impact survivability. This paper presents a design methodology of rigid-flex PCB systems with an emphasis on impact resistance. The design process considers solder joint adequacy, panel bending, and fracture using a finite element (FE) model. The proposed design methodology is developed using a case study with NASA JPL's Pop-Up Folding Flat Explorer Robot (PUFFER). First, the finite-element (FE) modeling methodology is presented with consideration to both frequency and time-domain modeling applications, which include operational self-contact analysis and high impact scenarios. The time-domain impact modeling methodology utilizes hyperelastic material properties for the Nomex hinges. This modeling method is validated using image correlation of PUFFER drop tests. A flowchart is presented to guide users through a validated Abaqus modeling procedure for highly flexible rigid-flex systems. Next, a case study is presented in which PUFFER is subject to drop heights representative of falls into Lunar pits and then the design is refined for a more optimum impact performance. Finally, the results of the case study are used to inform a generalized design methodology for rigid-flex PCB robotics subject to high-impact loads with the considerations presented.

John Bell↗
NASA NTRS2007

Finite Element Simulation of Solid Rocket Booster Separation Motors During Motor Firing

One of the toughest challenges facing Solid Rocket Booster (SRB) engineers is to ensure that any design changes made to the Shuttle-Derived Booster Separation Motors (BSM) for future space exploration vehicles is able to withstand the increasingly hostile motor firing environment without cracking its critical component - the graphite throat. This paper presents a critical analysis methodology and techniques for assessing effects of BSM design changes with great accuracy and precision. For current Space Shuttle operation, the motor firing occurs at SRB separation - approximately 125 seconds after Shuttle launch at an altitude of about 28 miles. The motor operation event lasts about two seconds, however, the surface temperature of the graphite throat increases approximately 3400 F in less than one second with a corresponding increase in surface pressure of approximately 2200 pounds per square inch (psi) in less than one-tenth of a second. To capture this process fully and accurately, a two-phase sequentially coupled thermal-mechanical finite element approach was developed. This method allows the time- and location-dependent pressure fields to interact with the spatial-temporal thermal fields throughout the operation. The material properties of graphite throat are orthotropic and temperature-dependent. The analysis involves preload and multiple body contacts.

Yu. Weiping↗
NASA NTRS2024

Finite Element Simulation of the Direct Energy Deposition using Comsol Multiphysics

Direct Energy Deposition (DED) is an emerging technology extensively employed in metal Additive Manufacturing (AM). Despite its widespread industrial application, mathematical modeling in this domain remains challenging. This complexity arises from the intricate nature of the modeling approach and the nonlinear behavior of material parameters across a broad temperature range. Consequently, experimentalists often resort to a trial-and-error method to achieve structures with desired properties. However, this approach can be time-consuming and may not always yield parts with the requisite characteristics, highlighting the necessity for mathematical modeling to enhance manufacturing success. This study focuses on thin-walled manufacturing with a single bead thickness, adjusting laser parameters to produce such structures. The laser cladding speed, typical for DED manufacturing, is considered to be on the order of centimeters per second. The various wall thicknesses and heights are explored to discern the general characteristics of walls manufactured via this DED approach. Our modeling approach diverges from the conventional DED modeling based on activation-deactivation of predefined mesh domains, commonly implemented in many finite element codes. Instead, a method is proposed that effectively models layer cladding and melt pool dynamics, enabling predictions of the microstructure in the resulting structures. The formation mechanisms of cellular, dendritic columnar, and stray (equiaxed) grains, which arise from the interplay between nucleation and growth from the surface is analyzed. The study also examines the feasibility of microstructure formation to demonstrate the various thermal characteristics inherent in wall manufacturing. Our results illustrate how different process parameters influence the temperature gradient and cooling rate of the molten pool, subsequently affecting the primary dendrite arm spacing (PDAS). This modeling technique allows for the investigation of diverse thermal conditions, facilitating the prediction of microstructure and residual stresses in the manufactured parts.

modeling↗
DOE OSTI2020

The effects of heat treatment on the response of WE43 Mg alloy: crystal plasticity finite element simulation and SEM-DIC experiment

The present report addressed the effects of heat treatment on the mechanical response of a WE43 Mg alloy using an integrated framework of SEM-DIC experiment and CPFE simulation. Both macroscopic responses including yield strength, ultimate strength, ductility, and microscopic responses, including local displacement and strain maps, were experimentally investigated. The focus of this work is to use the CPFE simulation as an integrated computational tool to study the effects of heat treatment. The CPFE framework was evaluated using the local fields of displacement and strain obtained from the SEM-DIC experiment rather than the conventional scheme of using macroscopic responses at different loading directions. Subsequently, the information which is available using CPFE, such as the critical resolved shear stress (CRSS) and relative slip activity, was used to study the effects of heat treatment on the response of WE43 Mg alloy. The contributions of different strengthening mechanisms on the CRSS were addressed. The results show that effects of heat treatment can be captured using the predominant mechanisms of the grain size effect and the influence of precipitates. Finally, it has been shown that classical Hall-Petch in which one constant can capture the size effects, should be modified. To do so, each deformation mode should have a unique Hall-Petch constant, which are calculated here for the WE43 Mg alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Crystal plasticity finite element simulation of lattice rotation and x-ray diffraction during laser shock compression of tantalum

Here we present a crystal plasticity model tailored for high-pressure, high-strain-rate conditions that uses a multiscale treatment of dislocation-based slip kinetics. We use this model to analyze the pronounced plasticity-induced lattice rotations observed in shock-compressed polycrystalline tantalum via in situ x-ray diffraction. By making direct comparisons between experimentally measured and simulated texture evolution, we can explain how the details of the underlying slip kinetics control the degree of lattice rotation that ensues. Specifically, we show that only the highly nonlinear kinetics caused by dislocation nucleation can explain the magnitude of the rotation observed under shock compression. We demonstrate a good fit between our crystal plasticity model and x-ray diffraction data and exploit the data to quantify the dislocation nucleation rates that are otherwise poorly constrained by experiment in the dynamic compression regime.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Finite Element Simulation of the Acoustic Pressure Inside a Beverage Container for Non-Thermal, Ultrasound-based Pasteurization

The purpose of this effort is to investigate whether large acoustic pressure waves can be transmitted inside beverage containers to enable pasteurization. Acoustic waves are known to induce large nonlinear compressive forces and shock waves in fluids, suggesting that compression waves may be capable of damaging bacteria inside beverage containers without appreciably increasingly the temperature or altering the freshness and flavor of the beverage contents. Although a combined process such as thermosonication (e.g., sonication with heating) is likely more efficient, it is instructive to compute the acoustic pressure field distribution inside the beverage container. The COMSOL simulations used two and three-dimensional models of beverage containers placed in a water bath to compute the acoustic pressure field. A limitation of these COMSOL models is that they cannot determine the bacterial lysis efficiency, rather the models provide an indirect metric of bacterial lysis based on the magnitude of the pressure field and its distribution.

42 ENGINEERING↗