Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flight Mechanics Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Mechanisms of Active Aerodynamic Load Reduction on a Rotorcraft Fuselage With Rotor Effects

The reduction of the aerodynamic load that acts on a generic rotorcraft fuselage by the application of active flow control was investigated in a wind tunnel test conducted on an approximately 1/3-scale powered rotorcraft model simulating forward flight. The aerodynamic mechanisms that make these reductions, in both the drag and the download, possible were examined in detail through the use of the measured surface pressure distribution on the fuselage, velocity field measurements made in the wake directly behind the ramp of the fuselage and computational simulations. The fuselage tested was the ROBIN-mod7, which was equipped with a series of eight slots located on the ramp section through which flow control excitation was introduced. These slots were arranged in a U-shaped pattern located slightly downstream of the baseline separation line and parallel to it. The flow control excitation took the form of either synthetic jets, also known as zero-net-mass-flux blowing, and steady blowing. The same set of slots were used for both types of excitation. The differences between the two excitation types and between flow control excitation from different combinations of slots were examined. The flow control is shown to alter the size of the wake and its trajectory relative to the ramp and the tailboom and it is these changes to the wake that result in a reduction in the aerodynamic load.

Schaeffler, Norman W.↗
NASA NTRS2019

ASPIRE Aerodynamic Models and Flight Performance

The Advanced Supersonic Parachute Inflation Research Experiments (ASPIRE) project waslaunched to develop the capability for testing supersonic parachutes at Mars-relevant conditions.Three initial parachute tests, targeted as a risk-reduction activity for NASA's upcoming Mars2020 mission, successfully tested two candidate parachute designs and provided valuable data onparachute inflation, forces, and aerodynamic behavior. Design of the flight tests depended onflight mechanics simulations which in turn required aerodynamic models for the payload, andthe parachute. Computational Fluid Dynamics (CFD) was used to generate these models preflightand they are compared against the flight data after the tests. For the payload, thereconstructed aerodynamic behavior is close to the pre-flight predictions, but the uncertaintiesin the reconstructed data are high due to the low dynamic pressures and accelerations duringthe flight period of comparison. For the parachute, the predicted time to inflation agrees wellwith the pre-flight model; the peak aerodynamic force and the steady state drag on the parachuteare within the bounds of the pre-flight models, even as the models over-predict the parachutedrag at supersonic Mach numbers. Notably, the flight data do not show the transonic dragdecrease predicted by the pre-flight model. The ASPIRE flight tests provide previouslyunavailable valuable data on the performance of a large full-scale parachute behind a slenderleading body at Mars-relevant Mach number, dynamic pressure and parachute loads. TheASPIRE results are used to propose a new model for the parachute drag behind slender bodiesto aid future experiments.

Muppidi, Suman↗
NASA NTRS2024

NASA Engineering and Safety Center Technical Bulletin No. 24-04: 6DOF Check Cases

In 2015, the NESC released benchmark Earth-based check-cases for well specified, rigid-body, six-degree-of-freedom (6DOF) aero/spacecraft models to promote consistent and accurate flight simulations across multiple Agency tools and facilities. Recently, the NESC expanded upon that effort to add Lunar-based check-cases to support new lunar exploration initiatives. This study produced a smaller, focused set of cases that exercise new and unique features of missions in the lunar environment in comparison with 8 high-fidelity NASA simulation tools and provides a measure of validation for simulations supporting Human Landing Systems.

Flight Mechanics↗
NASA NTRS1985

Factors affecting dwell times on digital displaying

A series of exploratory tests were conducted to investigate the effects of advanced display formats and display media on pilot scanning behavior using Langley's oculometer, a desktop flight simulator, a conventional electro-mechanical meter, and various digital displays. The primary task was for the test subject to maintain level flight, on a specific course heading, during moderate turbulence. A secondary task of manually controlling the readout of a display was used to examine the effects of the display format on a subject's scan behavior. Secondary task scan parameters that were evaluated were average dwell time, dwell time histograms, and number of dwells per meter change. The round dial meter demonstrated shorter dwell times and fewer dwells per meter change than the digital displays. The following factors affected digital display scanning behavior: (1) the number of digits; (2) the update rate of the digits; (3) the display media; and (4) the character font. The size of the digits used in these tests (0.28 to 0.50 inches) did not affect scan behavior measures.

Williams, A. J.↗
NASA NTRS1995

Space Shuttle solid rocket motor slag expulsion mechanisms

A 13 psi pressure perturbation occurred at approximately 68 seconds on the right Redesigned Solid Rocket Motor (RSRM) during the STS-54 space shuttle mission. While pressure perturbations are a normal characteristic of RSRM operation, the magnitude of the STS-54 perturbation and the resulting thrust imbalance between the left and right motors was outside of flight experience. A joint Marshall Space Flight Center (MSFC) and Thiokol Corporation (RSRM manufacturer) team soon narrowed the probable cause to a temporary nozzle restriction due to slag expulsion. In support of the team, Rockwell Aerospace performed fluid finite element simulations and vehicle flight dynamic correlations to investigate possible slag expulsion mechanisms responsible for pressure perturbations. Results of the simulations and analyses provided evidence that the combination of flight induced accelerations acting on accumulated slag and nozzle vectoring were the most probable cause of RSRM slag expulsion.

Hopson, Charles B.↗
NASA NTRS1975

Modelling atmospheric turbulence for a motion-based simulator

The background information in establishing several proposed atmospheric turbulence models for use on motion based aircraft simulators was documented. A specific model was proposed which, in addition to varying turbulence intensity (rms velocity), varies the atmospheric turbulence scale length to achieve compatibility with real atmospheric turbulence. With a suitable combination of scale length and intensity distribution, the model will simulate various atmospheric conditions characterized by altitude, stability, and terrain. The model is mechanized to be included in a flight simulator experiment in order to determine to what extent the pilots are sensitive to changes in atmospheric conditions and the realism of the model. The following topics were covered: literature survey, presently used techniques, proposed model, and simulation details.

Jacobson, I. D.↗
NASA NTRS2016

Effects of Zoledronate and Mechanical Loading during Simulated Weightlessness on Bone Structure and Mechanical Properties

Space flight modulates bone remodeling to favor bone resorption. Current countermeasures include an anti-resorptive drug class, bisphosphonates (BP), and high-force loading regimens. Does the combination of anti-resorptives and high-force exercise during weightlessness have negative effects on the mechanical and structural properties of bone? In this study, we implemented an integrated model to mimic mechanical strain of exercise via cyclical loading (CL) in mice treated with the BP Zoledronate (ZOL) combined with hindlimb unloading (HU). Our working hypothesis is that CL combined with ZOL in the HU model induces additive structural and mechanical changes. Thirty-two C57BL6 mice (male,16 weeks old, n8group) were exposed to 3 weeks of either HU or normal ambulation (NA). Cohorts of mice received one subcutaneous injection of ZOL (45gkg), or saline vehicle, prior to experiment. The right tibia was axially loaded in vivo, 60xday to 9N in compression, repeated 3xweek during HU. During the application of compression, secant stiffness (SEC), a linear estimate of slope of the force displacement curve from rest (0.5N) to max load (9.0N), was calculated for each cycle once per week. Ex vivo CT was conducted on all subjects. For ex vivo mechanical properties, non-CL left femurs underwent 3-point bending. In the proximal tibial metaphysis, HU decreased, CL increased, and ZOL increased the cancellous bone volume to total volume ratio by -26, +21, and +33, respectively. Similar trends held for trabecular thickness and number. Ex vivo left femur mechanical properties revealed HU decreased stiffness (-37),and ZOL mitigated the HU stiffness losses (+78). Data on the ex vivo Ultimate Force followed similar trends. After 3 weeks, HU decreased in vivo SEC (-16). The combination of CL+HU appeared additive in bone structure and mechanical properties. However, when HU + CL + ZOL were combined, ZOL had no additional effect (p0.05) on in vivo SEC. Structural data followed this trend with ZOL not modulating trabecular thickness in CL + NAHU mice. In summary, our integrated model simulates the combination of weightlessness, exercise-induced mechanical strain, and anti-resorptive treatment that astronauts experience during space missions. Based on these results, we conclude that, at the structural and stiffness level, zoledronate treatment during simulated spaceflight does not impede the skeletal response to axial compression. In contrast to our hypothesis, our data show that zoledronate confers no additional mechanical or structural benefit beyond those gained from cyclical loading.

Mechanical Loading↗
NASA NTRS1976

Mechanical design of NASA Ames Research Center vertical motion simulator

NASA has designed and is constructing a new flight simulator with large vertical travel. Several aspects of the mechanical design of this Vertical Motion Simulator (VMS) are discussed, including the multiple rack and pinion vertical drive, a pneumatic equilibration system, and the friction-damped rigid link catenaries used as cable supports.

Engelbert, D. F.↗
NASA NTRS2010

Verification Challenges of Dynamic Testing of Space Flight Hardware

The Six Degree-of-Freedom Dynamic Test System (SDTS) is a test facility at the National Aeronautics and Space Administration (NASA) Johnson Space Center in Houston, Texas for performing dynamic verification of space structures and hardware. Some examples of past and current tests include the verification of on-orbit robotic inspection systems, space vehicle assembly procedures and docking/berthing systems. The facility is able to integrate a dynamic simulation of on-orbit spacecraft mating or demating using flight-like mechanical interface hardware. A force moment sensor is utilized for input to the simulation during the contact phase, thus simulating the contact dynamics. While the verification of flight hardware presents many unique challenges, one particular area of interest is with respect to the use of external measurement systems to ensure accurate feedback of dynamic contact. There are many commercial off-the-shelf (COTS) measurement systems available on the market, and the test facility measurement systems have evolved over time to include two separate COTS systems. The first system incorporates infra-red sensing cameras, while the second system employs a laser interferometer to determine position and orientation data. The specific technical challenges with the measurement systems in a large dynamic environment include changing thermal and humidity levels, operational area and measurement volume, dynamic tracking, and data synchronization. The facility is located in an expansive high-bay area that is occasionally exposed to outside temperature when large retractable doors at each end of the building are opened. The laser interferometer system, in particular, is vulnerable to the environmental changes in the building. The operational area of the test facility itself is sizeable, ranging from seven meters wide and five meters deep to as much as seven meters high. Both facility measurement systems have desirable measurement volumes and the accuracies vary within the respective volumes. In addition, because this is a dynamic facility with a moving test bed, direct line-of-sight may not be available at all times between the measurement sensors and the tracking targets. Finally, the feedback data from the active test bed along with the two external measurement systems must be synchronized to allow for data correlation. To ensure the desired accuracy and resolution of these systems, calibration of the systems must be performed regularly. New innovations in sensor technology itself are periodically incorporated into the facility s overall measurement scheme. In addressing the challenges of the measurement systems, the facility is able to provide essential position and orientation data to verify the dynamic performance of space flight hardware.

Winnitoy, Susan↗
NASA NTRS1976

Summary of flight tests to determine the spin and controllability characteristics of a remotely piloted, large-scale (3/8) fighter airplane model

An unpowered, large, dynamically scaled airplane model was test flown by remote pilot to investigate the stability and controllability of the configuration at high angles of attack. The configuration proved to be departure/spin resistant; however, spins were obtained by using techniques developed on a flight support simulator. Spin modes at high and medium high angles of attack were identified, and recovery techniques were investigated. A flight support simulation of the airplane model mechanized with low speed wind tunnel data over an angle of attack range of + or - 90 deg. and an angle of sideslip range of + or - 40 deg. provided insight into the effects of altitude, stability, aerodynamic damping, and the operation of the augmented flight control system on spins. Aerodynamic derivatives determined from flight maneuvers were used to correlate model controllability with two proposed departure/spin design criteria.

Holleman, E. C.↗
NASA NTRS2006

Modeling and Testing of Docking and Berthing Mechanisms

The Contact Dynamics Simulation Laboratory (CDSL) of the Marshall Space Flight Center provides for refined hardware-in-the-loop real-time simulation of docking and berthing mechanisms and associated control systems. This facility is employed to verify the performance of docking/berthing mechanisms during Earth-orbit operations, determine the capture envelope of dockingherthing devices, measure contact loads at vehicle interfaces, and evaluate visual cues for man-in-the-loop operations. The CDSL has developed test verified analytical models of such systems as the ISS Common Berthing Mechanism and HST Three Point Docking Mechanism. This paper will describe the modeling and test techniques employed at the CDSL and present results from recent programs.

Hall, D. P.↗
NASA NTRSDate not supplied

Advanced Supersonic Parachute Inflation Research Experiment 2 (ASPIRE2) Flight Mechanics and Parachute Performance

The Advanced Supersonic Parachute Inflation Re-search Experiment-2 (ASPIRE2) program consists of a sounding rocket flight test to be launched at Wallops Flight Facility (WFF) in 2025. This effort seeks to qualify the supersonic parachute for the Sample Retrieval Lander (SRL) under the Mars Sample Return (MSR) program, building off the successes of its predecessor program, ASPIRE, which launched in both 2017 and 2018. The conops for the ASPIRE2 mission are shown in Figure 1 relative to its predecessor. While the ASPIRE pro-gram qualified a 21.5 m diameter disk-gap band parachute deployed at Mach 1.7, the SRL parachute will be increased to 24 m in diameter and target a Mach 2.1 parachute deployment condition, the largest diameter supersonic parachute deployed at the highest Mach number to date. These requirements are driven by the increased landing mass of the sample retrieval lander, which is roughly a 50% increase over that of the Mars2020 entry vehicle. These changes necessitate ASPIRE2 to certify the parachute performance under similar deployment conditions. This work will cover the 6-DoF para-chute model implementation and flight mechanics performance for the ASPIRE2 campaign and discuss how these results will impact the design of the test article. The ASPIRE2 trajectory is simulated using a multi-body flight dynamics tool, Program to Optimize Simulated Trajectories II (POST2). This work will summarize both the flight mechanics and parachute modeling (from payload separation until splashdown) and performance for this mission. Various design trades will be assessed such as para-chute tuning parameters as well as vehicle center of gravity location.

Evan Roelke↗
NASA NTRS1987

Nonlinear simulation of a flexible aircraft in maneuvering flight

A mathematical model integrating nonlinear rigid-body flight mechanics and linear aeroelastic dynamics is examined; the equations of motion for an elastic aircraft in accelerated flight are developed using Lagrangian mechanics. This approach is used to construct a simulation model of an F/A-18 (configured with tip missiles) which includes angular/elastic inertial coupling (IC). In general, the elastic modes significantly affected by IC were aerodynamically decoupled from the rest of the model. The affected modes were those which induced changes in total aircraft mass distribution. The elastic effect is noticeable if deformation-induced mass distribution changes are significant with respect to modal mass and modal frequencies. A modal parameter is presented which characterizes the level of IC between elastic momentum and rigid-body angular momentum.

Buttrill, Carey S.↗
NASA NTRS1992

Thermal-structural test facilities at NASA Dryden

The National Aero-Space Plane (NASP) has renewed interest in hypersonic flight and hot-structures technology development for both the airframe and engine. The NASA Dryden Thermostructures Research Facility is a unique national facility that was designed to conduct thermal-mechanical tests on aircraft and aircraft components by simulating the flight thermal environment in the laboratory. The layout of the facility is presented, which includes descriptions of the high-bay test area, the instrumentation laboratories, the mechanical loading systems, and the state-of-the-art closed-loop thermal control system. The hot-structures test capability of the facility is emphasized by the Mach-3 thermal simulation conducted on the YF-12 airplane. The Liquid-Hydrogen Structural Test Facility, which is presently in the design phase, will provide the capability of thermally testing structures containing hydrogen.

Deangelis, V. Michael↗
NASA NTRS2012

Cumulative Measurement Errors for Dynamic Testing of Space Flight Hardware

Located at the NASA Johnson Space Center in Houston, TX, the Six-Degree-of-Freedom Dynamic Test System (SDTS) is a real-time, six degree-of-freedom, short range motion base simulator originally designed to simulate the relative dynamics of two bodies in space mating together (i.e., docking or berthing). The SDTS has the capability to test full scale docking and berthing systems utilizing a two body dynamic docking simulation for docking operations and a Space Station Remote Manipulator System (SSRMS) simulation for berthing operations. The SDTS can also be used for nonmating applications such as sensors and instruments evaluations requiring proximity or short range motion operations. The motion base is a hydraulic powered Stewart platform, capable of supporting a 3,500 lb payload with a positional accuracy of 0.03 inches. The SDTS is currently being used for the NASA Docking System testing and has been also used by other government agencies. The SDTS is also under consideration for use by commercial companies. Examples of tests include the verification of on-orbit robotic inspection systems, space vehicle assembly procedures and docking/berthing systems. The facility integrates a dynamic simulation of on-orbit spacecraft mating or de-mating using flight-like mechanical interface hardware. A force moment sensor is used for input during the contact phase, thus simulating the contact dynamics. While the verification of flight hardware presents unique challenges, one particular area of interest involves the use of external measurement systems to ensure accurate feedback of dynamic contact. The measurement systems for the test facility have two separate functions. The first is to take static measurements of facility and test hardware to determine both the static and moving frames used in the simulation and control system. The test hardware must be measured after each configuration change to determine both sets of reference frames. The second function is to take dynamic measurements during hardware motion and contact. While performing dynamic testing of an active docking system, researchers found that the data from the motion platform, test hardware and two external measurement systems exhibited frame offsets and rotational errors. While the errors were relatively small when considering the motion scale overall, they substantially exceeded the individual accuracies for each component. After evaluating both the static and dynamic measurements, researchers found that the static measurements introduced significantly more error into the system than the dynamic measurements even though, in theory, the static measurement errors should be smaller than the dynamic. In several cases, the magnitude of the errors varied widely for the static measurements. Upon further investigation, researchers found the larger errors to be a consequence of hardware alignment issues, frame location and measurement technique whereas the smaller errors were dependent on the number of measurement points. This paper details and quantifies the individual and cumulative errors of the docking system and describes methods for reducing the overall measurement error. The overall quality of the dynamic docking tests for flight hardware verification was improved by implementing these error reductions.

Winnitoy, Susan↗
NASA NTRS1997

Thermal Structure Analysis of SIRCA Tile for X-34 Wing Leading Edge TPS

This paper will describe in detail thermal/structural analyses of SIRCA tiles which were performed at NASA Ames under the The Tile Analysis Task of the X-34 Program. The analyses used the COSMOS/M finite element software to simulate the material response in arc-jet tests, mechanical deflection tests, and the performance of candidate designs for the TPS system. Purposes of the analysis were to verify thermal and structural models for the SIRCA tiles, to establish failure criteria for stressed tiles, to simulate the TPS response under flight aerothermal and mechanical load, and to confirm that adequate safety margins exist for the actual TPS design.

Milos, Frank S.↗
NASA NTRSDate not supplied

Design of an Application Programming Interface for the Program to Optimize Simulated Trajectories II

A significant effort to upgrade the Program to Optimize Simulated Trajectories II (POST2), a heritage flight mechanics tool developed at NASA Langley Research Center, is ongoing to support current and future NASA missions. To meet mission requirements, it may be necessary for multiple specialized computational tools to interact to properly assess a system. An application programming interface for POST2 was developed to allow easier access for users and to enable communication between external applications. A demonstration of the POST2application programming interface is presented by utilizing common engineering platforms such as MATLAB and Python.

R Anthony Williams↗