Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flyer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Analysis of the performance of the space ultravacuum research facility in attached and free-flyer mode

The old concept of using the wake of a spacecraft to obtain an ultrahigh vacuum is revisited with a somewhat different emphasis. Since it is possible to configure a wake shield so that a surface of interest does not subtend any walls that could become contaminated, it appears that it should be possible to achieve a contamination-free, ultrahigh vacuum capability with infinite pumping speed even in the presence of high heat loads and moderate gas loads. With the new interest in developing thin films with precision controlled synthetic microstructures such as superlattices, mixed metal oxide high temperature superconductors, rare-earth magneto-optical devices, and nano-crystalline alloys, the ability to work with a variety of different materials without cross contamination should be of significance. This paper analyzes the performance of the conceptual design for a Space Ultravacuum Research Facility (SURF), both in a Shuttle-attached mode and as a free-flyer. It is shown that even in the Shuttle-attached mode, it should be possible to obtain vacuum levels equivalent to 10 to the -10 Torr with O and N2 as the primary constituents. This should be sufficient to demonstrate the feasibility of the concept, particularly the infinite pumping speed and virtual elimination of contamination aspects. As a free-flyer the SURF will be limited primarily by the gas load associated with the process being performed. For chemical beam epitaxy (CBE) it is shown that equivalent vacuum levels of 10 to the -14 Torr should be possible at 300 km.

Naumann, Robert J.↗

Biologically-inspired navigation and flight control for Mars flyer missions

Bioinspired Engineering Exploration Systems (BEES), is enabling new bioinspired sensors for autonomous exploration of Mars. The steps towards autonomy in development of these BEES flyers are described. A future set of Mars mission that are uniquely enabled by surch flyers are finally described.

bioinspired engineering Mars mission design flight↗

Austin Solar Guide (Flyer)

This flyer was developed to guide homeowners on their solar journey and expand the benefits of solar to local residents. The guide is an overview of various energy and solar programs and services through the Austin Energy utility with tips for spotting scams, a summary of common terms when designing a solar system, and considerations when searching for a solar contractor.

14 SOLAR ENERGY↗

Astrobee ISS Free Flyers: Overview and Enabling Technologies

The Astrobee robots began operations on the International Space Station (ISS) in April of 2019. These 32-cm-wide, 9-kg, cube-shaped free flyers are capable of autonomously traversing the US Orbital Segment of ISS and performing tasks to assist astronauts in their day-to-day activities. The Astrobee Facility also provides an on-orbit testbed for guest scientists desiring to try new technologies in zero-g. This presentation will provide an overview of the Astrobee system and some of its key enabling technologies, including propulsion, navigation, and human interfaces. Additional information and publications can be found on the Astrobee website: https://www.nasa.gov/astrobee.

Astrobee↗

(U) Validation and Optimization of a 1-Dimensional Quasi-Isentropic Compression Model Using a Functionally Graded Material Flyer Plate

The fields studying highly compressed materials have been around for many years. These fields have given birth to better understandings of the solar fusion cycle and the liquid-metallic core of Jupiter. The highest pressures achieved have been at the National Ignition Facility (NIF) and more recently, the Z-Machine. One method to achieve higher levels of compression is to use quasi-isentropic (QI) compression. In practice, this means minimizing the amount of temperature increase of the target material. In their paper, J.H. Nguyen et. al. manufactured a functionally graded material (FGM) in order to help them achieve QI compression. The aim of the study described in this paper is to validate a 1-dimensional (1D) FLAG model that uses an FGM flyer to compress a copper (Cu) target. Once validated, the density/composition profile of the FGM is varied and optimized using Markov Chain Monte Carlo, specifically using a Metropolis-Hastings algorithm to find the optimal FGM profile that minimizes the temperature increase in the copper.

36 MATERIALS SCIENCE↗

Shuttle payload vibroacoustic test plan evaluation. Free flyer payload applications and sortie payload parametric variations

A preliminary assessment of vibroacoustic test plan optimization for free flyer STS payloads is presented and the effects on alternate test plans for Spacelab sortie payloads number of missions are also examined. The component vibration failure probability and the number of components in the housekeeping subassemblies are provided. Decision models are used to evaluate the cost effectiveness of seven alternate test plans using protoflight hardware.

Stahle, C. V.↗

Propulsion-free separation and rendezvous of small shuttle free-flyers using controlled differential drag

A natural successor in the Shuttle era to many sounding rocket flights is the free-flyer mode of operation, in which the Shuttle Orbiter releases a subsatellite (with payloads), effects a desired separation, and approaches and retrieves the free-layer. The propulsive maneuvers required of the Orbiter by equivalent relative motions obtained through controlled differential drag (via changes in free-layer effective area and/or Orbiter attitude changes) are replaced. Simplified analytical techniques are developed and feasibility is verified.

King, J. C.↗

Free-flyer biostack experiment

The free-flyer biostack experiment is part of a radiobiological space research program that includes experiments in space as well as in accelerators on Earth. The program has been specially designed to increase knowledge concerning the importance, effectiveness, and hazards of the structured components of cosmic radiation to man and to any biological specimen in space. Up to now, our understanding of the ways in which HZE particles might affect biological matter is based on a few spaceflight experiments from the last Apollo missions and on the limited data available from heavy-ion irradiation from accelerators. In the near future, accelerators capable of accelerating particles up to higher atomic numbers and higher energies will promote increased activity in ground-based studies on biological effects of HZE particles. Comparison of data from such irradiation experiments on Earth with those from an actual spaceflight experiment will show any potential influence of the inevitably attendant spaceflight factors (e.g., weightlessness) on the radiobiological events.

Buecker, H.↗

Control of the induced microgravity environment of the Man Tended Free Flyer (MTFF)

Induced disturbance sources have been identified on board the Man Tended Free Flyer (MTFF). Vibration responses at sensitive payload/spacecraft interfaces have been predicted by the application of an empirically found spacecraft dynamic transfer function. Vibrations from fluid loops (Freon, water) and of reaction wheels are assessed to be the main contributors to the induced microgravity environment. The expected payload acceleration response amplitudes presented here are more than one hundred times higher than the admissible values given by the MTFF system requirement, not considering the structural striction-friction effects which could be avoided by appropriate design. Real responses will be significantly lower because the derivation of excitation and transmission functions are based on worst case assumptions. The results indicate that future activities must be concentrated on equipment design improvement and the implementation of vibration reduction along the disturbance transmission path. The activities must be accompanied by early equipment and assembly development tests and transmissibility measurements with the integrated spacecraft engineering and structural models in order to improve the accuracy of payload response predictions.

Schlund, Juergen↗

Space Flyer Unit (SFU)

The DSN (Deep Space Network) mission support requirements for the Space Flyer Unit (SFU) are summarized. The SFU is an unmanned, reusable, and retrievable free-flying platform for multipurpose use. The SFU spacecraft will carry seven individual experiments to be completed during its mission period. The mission objectives are outlined and the DSN support requirements are defined through the presentation of tables and narratives describing the spacecraft flight profile; DSN support coverage; frequency assignments; support parameters for telemetry, command and support systems; and tracking support responsibility.

Ninomiya, T.↗

Windsat Free Flyer using the advanced TIROS-N satellite

The results of this study show the feasibility of carrying a wind measuring lidar on an ATN-derivative free flying spacecraft. The overall configuration fits within the Shuttle bay and uses the same techniques for STS Launch as the proposed SAATN spacecraft. The lidar can be made light enough that the total weight of the satellite is well within the capability of the onboard propulsion system for transfers to a Sun synchronous orbit at 833 km attitude. The principal techniques for weight minimization are the use of the Perkin Elmer proprietary HIP process for the telescope, new packaging concepts for the laser and for the optics-laser interface, and the application of current technology to the signal processing hardware. Power minimization is achieved for the lidar primarily by use of a low pulse repetition frequency, i.e., 2pps, and again by the use of current processor technology. The power capability of the spacecraft is enhanced by increasing the ATN array size 25 percent, through the addition of two more solar array panels of the present size, and by limiting the range of Sun angles over which the spacecraft is operated. The same basic concept for the lidar as proposed in the Shuttle Windsat study is recommended here, but there are some changes in details to improve weight and power. No major technology break-throughs are required for the lidar, but some technology experiments are recommended for the laser subsystem to verify isotopic gas lifetime and performance, modulator life and weight, and for space qualification. Spacecraft changes are all natural modifications or growth to accommodate the payload. Overall, the proposed system provides substantial margin for the uncertainties for the future and for potential payload change, and also demonstrates the reasonableness of the Windsat Free Flyer concept.

Gurk, Herbert M.↗

A dual-armed free flyer

In this summary, we present the main conclusions and results of a design study conducted by a group of 25 students at the University of Maryland. The students, all participants in the spring 1988 courses ENEE488Q and ENEE418 in the Electrical Engineering Department, considered the problem of designing a free-flying space robot for applications in satellite servicing. In addition to the paper study, a subgroup of eight students undertook the ambitious task of designing and building a laboratory testbed for the concept of a free flyer. This subgroup has already completed the main fabrication of the mechanical hardware and most of the onboard electronics. When completed by the end of the summer, the testbed will consist of a seven-degree-of-freedom dual-armed planar robot that will float on an air table and carry out various commanded tasks. All the fabrication and testing is being conducted in the Intelligent Servosystems Laboratory at the University of Maryland. The project team split up into subgroups as follows: (1) articulation concepts 1 and 2, to study competing ideas for the overall systems architecture and manipulator design; (2) real time control systems group; (3) a computer graphics group to provide animations of a planar design; (4) a mechanical hardware design group for the laboratory testbed; and (5) a control systems hardware design group for the same.

Source record↗

A dual-armed free flyer

This summary presents the main conclusions and results of the design studies conducted by a group of 13 students at the University of Maryland. The students, all participants in the spring 1989 course ENEE418 in the Electrical Engineering Department, met weekly in a two-hour class to discuss and evaluate design alternatives. The main problem considered was the design and control of a planar testbed simulating a free-flying space robot for applications in satellite servicing. This project grew out of the 1988 class where a dual-armed free flyer (DAFF) was designed and partially built. This year, a group of six students continued the development of the DAFF, achieving computer-controlled motion of the DAFF's arms. All fabrication and testing of the DAFF is being conducted in the Intelligent Servosystems Laboratory at the University of Maryland. While the work related to the design and development of the DAFF is the main subject of the report, it should be noted that other students in the ENEE418 class have investigated additional issues related to manipulation in space. For example, one group studied a new parallel linkage based manipulator for fine motion applications such as in assembly operations in space. They investigated the mechanism's kinematics, its reachable workspace, and precision of applying forces and torques. In yet another project, a student set out to measure and map the friction characteristics of the actuators used in the Modular Dextrous Hand, which has been recently developed in the Intelligent Servosystems Laboratory. The results are expected to help compensate for this friction, which is a highly nonlinear disturbance and presents significant problems in high-precision, low-speed operations. This summary continues with the discussion of the results obtained by the group of students who have been working on developing the DAFF testbed.

Beck, D.↗

SIR-C/X-SAR free flyer concept

Viewgraphs on Spaceborne Imaging Radar (SAR) - C/X- Synthetic Aperture Radar (SAR) Free Flyer concept are presented. An overview, science objectives, science rationale, geophysical parameters from SAR, programmatic goals, concept description, and a candidate mission description are included.

Monson, R.↗

Ground data system for Space Flyer Unit (SFU)

The Space Flyer Unit (SFU) is an unmanned, multi-purpose, retrievable and reusable space platform. The first mission of SFU (SFU-1) will be launched by NASDA's H-2 launch vehicle in early 1995 and retrieved by NASA's Space Shuttle after several months in orbit. Two Japanese ground stations, several ground stations belonging to NASA, and a ground station in Chile will be used for tracking of SFU-1. The control center of SFU-1 is the Sagamihara Operations Center (SOC) of ISAS located in Sagamihara, Japan. This paper describes the tracking and data acquisition network for SFU-1, the configuration and design policy of the SFU operations control system, and data processing schemes used for mission operations of SFU.

Yamada, Takahiro↗