SEARCH · Search NASA

Results for “Flying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS2017

Flight Tests of a Remaining Flying Time Prediction System for Small Electric Aircraft in the Presence of Faults

This paper addresses the problem of building trust in the online prediction of a battery powered aircraft's remaining flying time. A series of flight tests is described that make use of a small electric powered unmanned aerial vehicle (eUAV) to verify the performance of the remaining flying time prediction algorithm. The estimate of remaining flying time is used to activate an alarm when the predicted remaining time is two minutes. This notifies the pilot to transition to the landing phase of the flight. A second alarm is activated when the battery charge falls below a specified limit threshold. This threshold is the point at which the battery energy reserve would no longer safely support two repeated aborted landing attempts. During the test series, the motor system is operated with the same predefined timed airspeed profile for each test. To test the robustness of the prediction, half of the tests were performed with, and half were performed without, a simulated powertrain fault. The pilot remotely engages a resistor bank at a specified time during the test flight to simulate a partial powertrain fault. The flying time prediction system is agnostic of the pilot's activation of the fault and must adapt to the vehicle's state. The time at which the limit threshold on battery charge is reached is then used to measure the accuracy of the remaining flying time predictions. Accuracy requirements for the alarms are considered and the results discussed.

Hogge, Edward F.↗

NASA NTRS2018

Remaining Flying Time Prediction Implementing Battery Prognostics Framework for Electric UAV's

In this paper the problem of building trust in the online safety prediction of an fixed wing small electric unmanned aerial vehicles (e-UAV) for remaining flying time is addressed. A series of flight tests are described to verify the performance of the remaining flying time prediction algorithm. The estimate of remaining flying time is used to activate an alarm when the predicted remaining time falls below a threshold of two minutes. This updates the pilot to transition to the landing sequence of the flight profile. A second alarm is activated when the battery state of charge (SOC) falls below a specified safety limit threshold. This SOC threshold is the point at which the battery energy reserve would no longer safely support enough aborted landing attempts. During the test flights, the motor system is operated with the same predefined timed airspeed profile for each test. To test the robustness of the developed prediction algorithm, partial tests were performed with and remaining were performed without a simulated power train fault. To simulate a partial power train fault in the e-UAV the pilot engages a resistor bank at a specified time during the test flight. The flying time prediction system is agnostic of the pilot's activation of the fault and must adapt to the vehicle's state. The time at which the limit threshold on battery SOC is reached, it is then used to measure the accuracy of the remaining flying time predictions. This is demonstrated through comparing results from two battery models being developed. Accuracy requirements for the alarms are considered and the results discussed.

Kulkarni, Chetan↗

NASA NTRS1981

Flying qualities criteria and flight control design

Despite the application of sophisticated design methodology, newly introduced aircraft continue to suffer from basic flying qualities deficiencies. Two recent meetings, the DOD/NASA Workshop on Highly Augmented Aircraft Criteria and the NASA Dryden Flight Research Center/Air Force Flight Test Center/AIAA Pilot Induced Oscillation Workshop, addressed this problem. An overview of these meetings is provided from the point of view of the relationship between flying qualities criteria and flight control system design. Among the items discussed are flying qualities criteria development, the role of simulation, and communication between flying qualities specialists and control system designers.

Berry, D. T.↗

NASA NTRS1982

Space Shuttle flying qualities and flight control system assessment

This paper reviews issues, data, and analyses relevant to the longitudinal flying qualities of the Space Shuttle in approach and landing. The manual control of attitude and path are first examined theoretically to demonstrate the unconventional nature of the Shuttle's augmented pitch and path response characteristics. The time domain pitch rate transient response criterion used for design of the Shuttle flight control system is examined in context with data from recent flying qualities experiments and operational aircraft. Questions arising from this examination are addressed through comparisons with MIL-F-8785C and other proposed flying qualities criteria which indicate potential longitudinal flying qualities problems. However, it is shown that these criteria, based largely on data from conventional aircraft, may be inappropriate for assessing the Shuttle.

Myers, T. T.↗

NASA NTRS1984

Flying qualities criteria for superaugmented aircraft

An overview of Dryden superaugmented aircraft flying qualities research is presented. This includes F-8 digital fly by wire flight experiments, orbiter flying qualities, shuttle improvements, AFTI/F-16, flying qualities and control system alternatives, Vertical Motion Simulator Shuttle evaluation and Total in Flight Simulator pitch rate criteria.

Berry, D. T.↗

NASA NTRS1990

Autonomous Martian flying rover

A remotely programmable, autonomous flying rover is proposed to extensively survey the Martian surface environment. A Mach .3, solar powered, modified flying wing could cover roughly a 2000 mile range during Martian daylight hours. Multiple craft launched from an orbiting mother ship could provide near-global coverage. Each craft is envisioned to fly at about 1 km above the surface and measure atmospheric composition, pressure and temperature, map surface topography, and remotely penetrate the near subsurface looking for water (ice) and perhaps evidence of life. Data collected are relayed to Earth via the orbiting mother ship. Near surface guidance and control capability is an adaptation of current cruise missile technology. A solar powered aircraft designed to fly in the low temperature, low density, carbon dioxide Martian atmosphere near the surface appears feasible.

Source record↗

NASA NTRS1991

Field of view location and formation flying for polar orbiting missions

The problem of flying an earth observing mission using a group of observatories flying in formation, rather than a single observatory, is addressed. Contraints placed on the design of the observatories and of the mission, if it is required that the instantaneous field of views of the two instruments overlap by a specified amount, are determined. The complexities of formation flying are found to greatly outweigh simpler solutions which combine instruments on a single spacecraft payload. While formation flying may be beneficial when crossing times and simultaneity arguments are not stringent, it is not practical for EOS. Accomplishment of the EOS scientific mission requires the simultaneous measurement of a basic set of earth system science parameters; it also requires that many events be observed by groups of instruments looking through the same atmospheric path.

Scolese, Christopher↗

NASA NTRS1940

Preliminary Investigation of the Flying Qualities of Airplanes

The National Advisory Committee for Aeronautics is undertaking an investigation of the flying qualities of airplanes. The work consists in the determination of the significant qualities susceptible of measurement, the development of the instruments required to make the measurements, and the accumulation of data on the flying qualities of existing airplanes, which data are to serve as a basis for quantitative specifications for the flying qualities of future designs. A tentative schedule of measurable flying qualities has been prepared and the instruments needed for their measurements have been assembled. A trial of the schedule and the instruments has been made using the Stinson SR-8e airplane. The results showed that, although the original schedule and instruments are basically satisfactory some further development is required to eliminate nonessential items and to expedite flight testing. The report describes and discusses the work done with this airplane.

Soule, H A↗

NASA NTRS1993

Primary display latency criteria based on flying qualities and performance data

With a pilots' increasing use of visual cue augmentation, much requiring extensive pre-processing, there is a need to establish criteria for new avionics/display design. The timeliness and synchronization of the augmented cues is vital to ensure the performance quality required for precision mission task elements (MTEs) where augmented cues are the primary source of information to the pilot. Processing delays incurred while transforming sensor-supplied flight information into visual cues are unavoidable. Relationships between maximum control system delays and associated flying qualities levels are documented in MIL-F-83300 and MIL-F-8785. While cues representing aircraft status may be just as vital to the pilot as prompt control response for operations in instrument meteorological conditions, presently, there are no specification requirements on avionics system latency. To produce data relating avionics system latency to degradations in flying qualities, the Navy conducted two simulation investigations. During the investigations, flying qualities and performance data were recorded as simulated avionics system latency was varied. Correlated results of the investigation indicates that there is a detrimental impact of latency on flying qualities. Analysis of these results and consideration of key factors influencing their application indicate that: (1) Task performance degrades and pilot workload increases as latency is increased. Inconsistency in task performance increases as latency increases. (2) Latency reduces the probability of achieving Level 1 handling qualities with avionics system latency as low as 70 ms. (3) The data suggest that the achievement of desired performance will be ensured only at display latency values below 120 ms. (4) These data also suggest that avoidance of inadequate performance will be ensured only at display latency values below 150 ms.

Funk, John D., Jr.↗

NASA NTRS1994

High angle of attack flying qualities criteria for longitudinal rate command systems

This study was designed to investigate flying qualities requirements of alternate pitch command systems for fighter aircraft at high angle of attack. Flying qualities design guidelines have already been developed for angle of attack command systems at 30, 45, and 60 degrees angle of attack, so this research fills a similar need for rate command systems. Flying qualities tasks that require post-stall maneuvering were tested during piloted simulations in the McDonnell Douglas Aerospace Manned Air Combat Simulation facility. A generic fighter aircraft model was used to test angle of attack rate and pitch rate command systems for longitudinal gross acquisition and tracking tasks at high angle of attack. A wide range of longitudinal dynamic variations were tested at 30, 45, and 60 degrees angle of attack. Pilot comments, Cooper-Harper ratings, and pilot induced oscillation ratings were taken from five pilots from NASA, USN, CAF, and McDonnell Douglas Aerospace. This data was used to form longitudinal design guidelines for rate command systems at high angle of attack. These criteria provide control law design guidance for fighter aircraft at high angle of attack, low speed flight conditions. Additional time history analyses were conducted using the longitudinal gross acquisition data to look at potential agility measures of merit and correlate agility usage to flying qualities boundaries. This paper presents an overview of this research.

Wilson, David J.↗

NASA NTRS1999

Integration of a Decentralized Linear-Quadratic-Gaussian Control into GSFC's Universal 3-D Autonomous Formation Flying Algorithm

A decentralized control is investigated for applicability to the autonomous formation flying control algorithm developed by GSFC for the New Millenium Program Earth Observer-1 (EO-1) mission. This decentralized framework has the following characteristics: The approach is non-hierarchical, and coordination by a central supervisor is not required; Detected failures degrade the system performance gracefully; Each node in the decentralized network processes only its own measurement data, in parallel with the other nodes; Although the total computational burden over the entire network is greater than it would be for a single, centralized controller, fewer computations are required locally at each node; Requirements for data transmission between nodes are limited to only the dimension of the control vector, at the cost of maintaining a local additional data vector. The data vector compresses all past measurement history from all the nodes into a single vector of the dimension of the state; and The approach is optimal with respect to standard cost functions. The current approach is valid for linear time-invariant systems only. Similar to the GSFC formation flying algorithm, the extension to linear LQG time-varying systems requires that each node propagate its filter covariance forward (navigation) and controller Riccati matrix backward (guidance) at each time step. Extension of the GSFC algorithm to non-linear systems can also be accomplished via linearization about a reference trajectory in the standard fashion, or linearization about the current state estimate as with the extended Kalman filter. To investigate the feasibility of the decentralized integration with the GSFC algorithm, an existing centralized LQG design for a single spacecraft orbit control problem is adapted to the decentralized framework while using the GSFC algorithm's state transition matrices and framework. The existing GSFC design uses both reference trajectories of each spacecraft in formation and by appropriate choice of coordinates and simplified measurement modeling is formulated as a linear time-invariant system. Results for improvements to the GSFC algorithm and a multiple satellite formation will be addressed. The goal of this investigation is to progressively relax the assumptions that result in linear time-invariance, ultimately to the point of linearization of the non-linear dynamics about the current state estimate as in the extended Kalman filter. An assessment will then be made about the feasibility of the decentralized approach to the realistic formation flying application of the EO-1/Landsat 7 formation flying experiment.

Folta, David C.↗

NASA NTRS2001

Preliminary Results of NASA's First Autonomous Formation Flying Experiment: Earth Observing-1 (EO-1)

NASA's first autonomous formation flying mission is completing a primary goal of demonstrating an advanced technology called enhanced formation flying. To enable this technology, the Guidance, Navigation, and Control center at the Goddard Space Flight Center has implemented an autonomous universal three-axis formation flying algorithm in executive flight code onboard the New Millennium Program's (NMP) Earth Observing-1 (EO-1) spacecraft. This paper describes the mathematical background of the autonomous formation flying algorithm and the onboard design and presents the preliminary validation results of this unique system. Results from functionality assessment and autonomous maneuver control are presented as comparisons between the onboard EO-1 operational autonomous control system called AutoCon(tm), its ground-based predecessor, and a stand-alone algorithm.

Folta, David↗

NASA NTRS2001

Results of NASA's First Autonomous Formation Flying Experiment: Earth Observing-1 (EO-1)

NASA's first autonomous formation flying mission completed its primary goal of demonstrating an advanced technology called enhanced formation flying. To enable this technology, the Guidance, Navigation, and Control center at the Goddard Space Flight Center (GSFC) implemented a universal 3-axis formation flying algorithm in an autonomous executive flight code onboard the New Millennium Program's (NMP) Earth Observing-1 (EO-1) spacecraft. This paper describes the mathematical background of the autonomous formation flying algorithm and the onboard flight design and presents the validation results of this unique system. Results from functionality assessment through fully autonomous maneuver control are presented as comparisons between the onboard EO-1 operational autonomous control system called AutoCon(tm), its ground-based predecessor, and a standalone algorithm.

Folta, David C.↗

NASA NTRS2002

Simulation of Guidance, Navigation, and Control Systems for Formation Flying Missions

Concepts for missions of distributed spacecraft flying in formation abound. From high resolution interferometry to spatially distributed in-situ measurements, these mission concepts levy a myriad of guidance, navigation, and control (GNC) requirements on the spacecraft/formation as a single system. A critical step toward assessing and meeting these challenges lies in realistically simulating distributed spacecraft systems. The Formation Flying TestBed (FFTB) at NASA Goddard Space Flight Center's (GSFC) Guidance, Navigation, and Control Center is a hardware-in-the-loop simulation and development facility focused on GNC issues relevant to formation flying systems. The FFTB provides a realistic simulation of the vehicle dynamics and control for formation flying missions in order to: (1) conduct feasibility analyses of mission requirements, (2) conduct and answer mission and spacecraft design trades, and (3) serve as a host for GNC software and hardware development and testing. The initial capabilities of the FFTB are based upon an integration of high fidelity hardware and software simulation, emulation, and test platforms developed or employed at GSFC in recent years, including a high-fidelity Global Positioning System (GPS) simulator which has been a fundamental component of the GNC Center's GPS Test Facility. The FFTB will be continuously evolving over the next several years from a tool with capabilities in GPS navigation hardware/software-in-the-loop analysis and closed loop GPS-based orbit control algorithm assessment. Eventually, it will include full capability to support all aspects of multi-sensor, absolute and relative state determination and control, in all (attitude and orbit) degrees of freedom, as well as information management for satellite clusters and constellations. A detailed description of the FFTB architecture is presented in the paper.

Burns, Rich↗

NASA NTRS2003

First Results from a Hardware-in-the-Loop Demonstration of Closed-Loop Autonomous Formation Flying

A closed-loop system for the demonstration of autonomous satellite formation flying technologies using hardware-in-the-loop has been developed. Making use of a GPS signal simulator with a dual radio frequency outlet, the system includes two GPS space receivers as well as a powerful onboard navigation processor dedicated to the GPS-based guidance, navigation, and control of a satellite formation in real-time. The closed-loop system allows realistic simulations of autonomous formation flying scenarios, enabling research in the fields of tracking and orbit control strategies for a wide range of applications. The autonomous closed-loop formation acquisition and keeping strategy is based on Lyapunov's direct control method as applied to the standard set of Keplerian elements. This approach not only assures global and asymptotic stability of the control but also maintains valuable physical insight into the applied control vectors. Furthermore, the approach can account for system uncertainties and effectively avoids a computationally expensive solution of the two point boundary problem, which renders the concept particularly attractive for implementation in onboard processors. A guidance law has been developed which strictly separates the relative from the absolute motion, thus avoiding the numerical integration of a target trajectory in the onboard processor. Moreover, upon using precise kinematic relative GPS solutions, a dynamical modeling or filtering is avoided which provides for an efficient implementation of the process on an onboard processor. A sample formation flying scenario has been created aiming at the autonomous transition of a Low Earth Orbit satellite formation from an initial along-track separation of 800 m to a target distance of 100 m. Assuming a low-thrust actuator which may be accommodated on a small satellite, a typical control accuracy of less than 5 m has been achieved which proves the applicability of autonomous formation flying techniques to formations of satellites as close as 50 m.

Gill, E.↗

NASA NTRS2000

Flight-Test Validation and Flying Qualities Evaluation of a Rotorcraft UAV Flight Control System

This paper presents a process of design and flight-test validation and flying qualities evaluation of a flight control system for a rotorcraft-based unmanned aerial vehicle (RUAV). The keystone of this process is an accurate flight-dynamic model of the aircraft, derived by using system identification modeling. The model captures the most relevant dynamic features of our unmanned rotorcraft, and explicitly accounts for the presence of a stabilizer bar. Using the identified model we were able to determine the performance margins of our original control system and identify limiting factors. The performance limitations were addressed and the attitude control system was 0ptimize.d for different three performance levels: slow, medium, fast. The optimized control laws will be implemented in our RUAV. We will first determine the validity of our control design approach by flight test validating our optimized controllers. Subsequently, we will fly a series of maneuvers with the three optimized controllers to determine the level of flying qualities that can be attained. The outcome enable us to draw important conclusions on the flying qualities requirements for small-scale RUAVs.

Mettler, Bernard↗

NASA NTRS2003

Development of a Crosslink Channel Simulator for Simulation of Formation Flying Satellite Systems

Multi-vehicle missions are an integral part of NASA s and other space agencies current and future business. These multi-vehicle missions generally involve collectively utilizing the array of instrumentation dispersed throughout the system of space vehicles, and communicating via crosslinks to achieve mission goals such as formation flying, autonomous operation, and collective data gathering. NASA s Goddard Space Flight Center (GSFC) is developing the Formation Flying Test Bed (FFTB) to provide hardware-in- the-loop simulation of these crosslink-based systems. The goal of the FFTB is to reduce mission risk, assist in mission planning and analysis, and provide a technology development platform that allows algorithms to be developed for mission hctions such as precision formation flying, synchronization, and inter-vehicle data synthesis. The FFTB will provide a medium in which the various crosslink transponders being used in multi-vehicle missions can be plugged in for development and test. An integral part of the FFTB is the Crosslink Channel Simulator (CCS),which is placed into the communications channel between the crosslinks under test, and is used to simulate on-orbit effects to the communications channel due to relative vehicle motion or antenna misalignment. The CCS is based on the Starlight software programmable platform developed at General Dynamics Decision Systems which provides the CCS with the ability to be modified on the fly to adapt to new crosslink formats or mission parameters.

Hart, Roger↗

NASA NTRS2004

Formation Flying: The Future of Remote Sensing from Space

Over the next two decades a revolution is likely to occur in how remote sensing of Earth, other planets or bodies, and a range of phenomena in the universe is performed from space. In particular, current launch vehicle fairing volume and mass constraints will continue to restrict the size of monolithic telescope apertures which can be launched to little or no greater size than that of the Hubble Space Telescope, the largest aperture currently flying in space. Systems under formulation today, such as the James Webb Space Telescope will be able to increase aperture size and, hence, imaging resolution, by deploying segmented optics. However, this approach is limited as well, by our ability to control such segments to optical tolerances over long distances with highly uncertain structural dynamics connecting them. Consequently, for orders of magnitude improved resolution as required for imaging black holes, imaging planets, or performing asteroseismology, the only viable approach will be to fly a collection of spacecraft in formation to synthesize a virtual segmented telescope or interferometer with very large baselines. This paper provides some basic definitions in the area of formation flying, describes some of the strategic science missions planned in the National Aeronautics and Space Administration, and identifies some of the critical technologies needed to enable some of the most challenging space missions ever conceived which have realistic hopes of flying.

Leitner, Jesse↗