Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fracture energy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Adhesive fracture mechanics

In studies of fracture mechanics the adhesive fracture energy is regarded as a fundamental property of the adhesive system. It is pointed out that the value of the adhesive fracture energy depends on surface preparation, curing conditions, and absorbed monolayers. A test method reported makes use of a disk whose peripheral part is bonded to a substrate material. Pressure is injected into the unbonded central part of the disk. At a certain critical pressure value adhesive failure can be observed. A numerical stress analysis involving arbitrary geometries is conducted.

Bennett, S. J.↗
NASA NTRS1971

Investigation of the fracture mechanics of boride composites

Fracture energies of WC-6Co, Boride 5 (ZrB2+SiC), Boride 8(ZrB2+SiC+C) and Boride 8-M2(ZrB2+SiC+C) were measured by slow bend and impact tests of notched charpy bars. Cobalt bonded tungsten carbide exhibited impact energies of 0.76 ft-lb or 73.9 in-lb/square inch. Boride 5 and the Boride 8 exhibit impact energies one third and one quarter of that observed for WC-6Co comparing favorably with measurements for SiC and Si3N4. Slow bend-notched bar-fracture energies for WC-6Co were near 2.6 in-lb/square inch or 1/20 the impact energies. Slow bend energies for Boride 8-M2, Boride 8 and Boride 5 were 58%, 42% and 25% of the value observed for WC-6Co. Fractograph showed differences for WC-6Co where slow bend testing resulted in smooth transgranular cleavage while samples broken by impact exhibited intergranular failures. By contrast the boride fractures showed no distinction based on testing method. Fabrication studies were conducted to effect alteration of the boride composites by alloying and introduction of graphite cloth.

Kaufman, L.↗
DOE OSTI2025

Minimization of Cathode|Solid-Electrolyte Interfacial Delamination through the Application of Interphase Layers

Next-generation lithium-ion batteries are expected to use solid electrolytes (SEs) to enable higher energy density and extreme fast-charge capabilities. One major mode of degradation at the cathode|SE interface is delamination between the cathode active materials and SEs, which leads to performance decay. Experimental observations indicate that implementation of interphase layers can minimize the cathode|SE delamination induced capacity fade. A multiscale computational methodology is developed here to investigate the applicability of boron substituted lithium carbonate (Li 2+x B x C 1–x O 3 , x = 0.5, or LBCO) to minimize the delamination at the cathode|SE interface. Atomistic simulations indicate that the fracture energies at both the cathode|LBCO and LBCO|SE interfaces are higher than those at the cathode|SE interface, which reduces the extent of delamination. Mesoscale simulations indicate that, apart from increasing the fracture energy, decreasing the evolution of strain energy by lowering the elastic modulus of the interphase layer can also minimize the extent of delamination at the cathode|SE interface. However, the adoption of an interphase layer with high ionic conductivity is necessary to minimize the ohmic losses during operation at higher current densities. This study provides guidance on selecting interphase layers with specific properties and thicknesses to minimize both interfacial delamination and impedance growth.

LBCO↗
DOE OSTI2022

Plasma surface modification coupled with thermal and step-over distance effects on significant fracture improvement of adhesively-bonded metal-$\mathrm{CFRTP}$ dissimilar materials

Here, this work proposes an approach to improve the interfacial bonding between carbon-fiber-reinforced thermoplastic polymers (CFRTP) and thermoset adhesive by using the surface modification with the combination of air plasma, thermal, and step-over effects. Thanks to the proper heating which causes the exposure of carbon fibers on the CFRTP surface, both polymer matrix and these exposed carbon fibers can have improved bonding with adhesive due to air plasma treatment. By conducting the Double Cantilever Beam (DCB) tests performed on adhesively-bonded AA5052/CFRP-PA66 dissimilar joints, it was shown in this work that the average Mode I specific fracture energy can be improved up to about 180% compared to non-treated counterparts. The foregoing improvement can be further increased by considering the step-over distance of the surface treatment, which triggers the tortuous damage path in the failure process of adhesively-bonded structures. By manipulating this treatment parameter, often overlooked in the literature, and other parameters (i.e., treatment speed, nozzle tip-to-surface distance, etc.) investigated in this study, the average Mode I specific fracture energy of adhesively-bonded AA5052/CFRP-PA66 dissimilar joints can be improved reaching up to about 410% compared to non-treatment counterparts.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1976

Ductile fracture theories for pressurised pipes and containers

Two mechanisms of fracture are distinguished. Plane strain fractures occur in materials which do not undergo large-scale plastic deformations prior to and during a possible fracture deformation. Plane stress or high energy fractures are generally accompanied by large inelastic deformations. Theories for analyzing plane stress are based on the concepts of critical crack opening stretch, K(R) characterization, J-integral, and plastic instability. This last is considered in some detail. The ductile fracture process involves fracture initiation followed by a stable crack growth and the onset of unstable fracture propagation. The ductile fracture propagation process may be characterized by either a multiparameter (discrete) model, or some type of a resistance curve which may be considered as a continuous model expressed graphically. These models are studied and an alternative model is also proposed for ductile fractures which cannot be modeled as progressive crack growth phenomena.

Erdogan, F.↗
DOE OSTI2021

Directly Probing the Fracture Behavior of Ultrathin Polymeric Films

Understanding fracture mechanics of ultrathin polymeric films is crucial for modern technologies, including semiconductor and coating industries. However, up to now, the fracture behavior of sub-100 nm polymeric thin films is rarely explored due to challenges in handling samples and limited testing methods available. In this work, we report a new testing methodology that can not only visualize the evolution of the local stress distribution through wrinkling patterns and crack propagation during the deformation of ultrathin films but also directly measure their fracture energies. Using ultrathin polystyrene films as a model system, we both experimentally and computationally investigate the effect of the film thickness and molecular weight on their fracture behavior, both of which show a ductile-to-brittle transition. Furthermore, we demonstrate the broad applicability of this testing method in semicrystalline semiconducting polymers. We anticipate our methodology described here could provide new ways of studying the fracture behavior of ultrathin films under confinement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2002

Prediction of Long-Term Strength of Thermoplastic Composites Using Time-Temperature Superposition

Accelerated tests for composite failure were investigated. Constant ramp transverse strength tests on thermoplastic composite specimens were conducted at four temperatures from 300 F to 450 F and five duration times from 0.5 sec to 24 hrs. Up to 400 F, the time-temperature-superposition method produces a master curve allowing strength at longer times to be estimated from strength tests conducted over shorter times but at higher temperatures. The shift factors derived from compliance tests applied well to the strength data. To explain why strength behaved similar to compliance, a viscoelastic fracture model was investigated based on the hypothesis that the work of fracture for crack initiation at some critical flaw remains constant with time and temperature. The model, which used compliance as input, was found to fit the strength data only if the critical fracture energy was allowed to vary with stress rate. Fracture tests using double cantilever beam specimens were conducted from 300 F to 450 F over time scales similar to the strength study. The toughness data showed a significant change with loading rate, less variation with temperature, did not form a master curve, and could not be correlated with the fracture model. Since the fracture model did not fit the fracture data, an alternative explanation based on the dilatational strain energy density was proposed. However the usefulness of this model is severely limited because it relies on a critical parameter which varies with loading rate.

Reeder, James R.↗
DOE OSTI2025

Multiple‐Repeated Plasma Surface Treatments for Significantly Improving Bonding Performance of Metal‐Carbon‐Fiber‐Reinforced Thermoplastic Polymer Dissimilar Adhesive Joints

This work investigates how multiple‐repeated plasma surface treatments can significantly enhance adhesively bonded metal‐carbon‐fiber‐reinforced thermoplastic polymer (CFRTP) dissimilar joints, a topic that has been rarely investigated compared to other parameters during the plasma treatment process. By conducting double cantilever beam tests on adhesively bonded AA6061‐carbon‐fiber‐reinforced polyphthalamide (CFRPPA) dissimilar joints, it is shown that the average Mode I specific fracture energy after 20 repetitions of the same plasma treatment, using processing parameters without noticeably changing surface roughness, can be improved and saturated up to almost 2000% compared to non‐treated joints and almost 240% compared to a single plasma treatment commonly used in the literature. The improvement can be attributed to the enhanced chemical bonding at the CFRPPA‐adhesive interface. This study is important for achieving strong bonding performance of CFRTP‐related structural joints using multiple plasma treatments, a simple and effective method.

36 MATERIALS SCIENCE↗
NASA NTRS1984

The characterization of Mode I delamination failure in non-woven, multidirectional laminates

The uniform double cantilever beam test and SEM are presently used for the characterization of Mode I delamination behavior in fiber-reinforced epoxy laminates. Delamination failure assumes forms that depend on ply orientation, test specimen geometry, and matrix toughness, but the calculated fracture energy is noted to be heavily dependent on fracture surface morphology. A material property concept that is independent of both test specimen geometry and the orientation of the plies constituting the delaminating interface is elucidated, through the definition of interlaminar fracture solely in terms of an interlaminar separation that includes no fiber breakage or pull-out. This value, which dissipates the lowest possible amount of energy during crack growth, is the controlling factor for laminate toughness.

Chai, H.↗
DOE OSTI2025

Improving adhesive bonding of short carbon fiber thermoplastic composites to aluminum alloys with a hybrid laser-plasma surface modification strategy

This study investigates hybrid laser–plasma surface modification strategies for metal–CFRTP (carbon-fiber-reinforced thermoplastic polymer) dissimilar joints to improve their bonding performance, in contrast to existing literature that mostly focuses on either plasma or laser treatment alone. By conducting double cantilever beam (DCB) tests on adhesively-bonded AA5052 and CFRPA66 (carbon-fiber-reinforced polyamide 66) joints, as an example of metal–CFRTP joints, it was found that laser engraving on the metal surface combined with plasma treatment on the CFRTP surface significantly improved the specific fracture energy of the joint by 187% and 31% compared to as-received and plasma-treated-only joints, respectively. However, the hybrid treatment of laser engraving and plasma on the investigated CFRTP surface did not improve the bonding performance of the joints. The underlying mechanisms related to hybrid laser-plasma surface modification strategies were further investigated by examining the surface and cross-sectional morphologies after DCB testing using microscopy. Computational modeling was performed to elucidate the interaction between grooves on the metal substrate and the CFRTP–adhesive interfacial bonding in metal–CFRTP joints. This study provides new insights into developing surface modification methods for achieving strong metal–CFRTP adhesive joints, aimed at lightweighting structural components in automotive, aerospace, and other applications.

Adhesive bonding↗
DOE OSTI2024

An intrinsic ductility parameter derived from anisotropic linear elasticity theory

A new indicator of intrinsic ductility (κ) is introduced based on linear elasticity. In the limit of elastic isotropy this parameter is equal to the Pugh ratio ( B / G ) plus a constant; but unlike the Pugh ratio, κ incorporates anisotropy and crystallography to improve predictive value. We identify a single ductile-to-brittle transition setpoint for κ that predicts crack-tip plasticity in atomistic simulations, experimental elongation to failure of polycrystalline elemental metals pulled in tension, and fracture energy measurements of glasses, suggesting commonality in the relationship between plasticity and fracture across all three of these cases. Statistical analysis supports the superiority of κ over B / G at predicting crack-tip plasticity in atomistic simulations and elongation to failure of polycrystalline elemental metals.

Winter, Ian S.↗
DOE OSTI2024

Evaluating the Role of Metastable Surfaces in Mechanochemical Reduction of Molybdenum Oxide

Mechanochemistry and mechanocatalysis are gaining increasing attention as environmentally friendly chemical processes because of their solvent-free nature and scalability. Significant effort has been devoted for studying continuum-scale phenomena in mechanochemistry, such as temperature and pressure gradients, but the atomic-scale mechanisms remain relatively unexplored. In this work, we focus on the mechanochemical reduction of MoO3 as a case study. We use experimental techniques to determine the mechanochemical reduction conditions and density functional theory (DFT) simulations to establish an atomistic framework for identifying the metastable surfaces that are most likely to enable this process. Our results show that metastable surfaces can significantly lower or remove thermodynamic barriers for surface reduction and that kinetic energy from milling can facilitate the formation of metastable surfaces that have high surface fracture energies and are not thermally accessible. These findings indicate that metastable surfaces are an important aspect of mechanochemistry along with hot spots and other continuum-scale phenomena.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1988

Effect of finite width on deflection and energy release rate of an orthotropic double cantilever specimen

The problem of an orthotropic cantilevered plate subjected to a uniformly distributed end load is solved by the Rayleigh-Ritz energy method. The result is applied to laminated composite, double cantilevered specimens to estimate the effect of crack tip constraint on the transverse curvature, deflection and energy release rate. The solution is also utilized to determined finite width correction factors for fracture energy characterization tests in which neither plane stress nor plane strain conditions apply.

Schapery, R. A.↗
NASA NTRS1977

Analysis and testing of adhesive bonds

An adhesive fracture mechanics approach is described with reference to the identification and design of the best tests for evaluating a given adhesive, the definition of the most meaningful fundamental parameters by which adhesives might be characterized, and the application of these parameters to the design of joints and to the prediction of their performance. Topics include standard adhesive test techniques, the theory of adhesive fracture, and adhesive fracture energy tests. Analytical methods and computer techniques for adhesive bonding, chemical and physical aspects of adhesive fracture, and specific applications and aspects of adhesive fracture mechanics are discussed.

Anderson, G. P.↗
NASA NTRS1986

Criterion for mixed mode fracture in composite bonded joints

A study was undertaken to characterize the debond growth mechanism of adhesively bonded composite joints under mode I, mixed mode I-II, and mode II static loadings. The bonded system consisted of graphite-epoxy composite adherends bonded with a toughened epoxy adhesive. The mode I, mode II and mixed mode I-II fracture energies of the tested adhesives were found to be equal to each other. The criterion for mixed mode fracture in composite bonded joints was found.

Mall, S.↗
NASA NTRS1986

Criterion for mixed mode fracture in composite bonded joints

A study was undertaken to characterize the debond growth mechanism of adhesively bonded composite joints under mode I, mixed mode I-II, and mode II static loadings. The bonded system consisted of graphite/epoxy (T300/5208) composite adherends bonded with a toughened epoxy (EC 3445) adhesive. The mode I, mode II and mixed-mode I-II fracture energies of the tested adhesive were found to be equal to each other. Furthermore, the criterion for mixed mode fracture in composite bonded joints was determined.

Mall, S.↗
DOE OSTI2026

Capturing the fractocohesive length scale in elastomers through a statistical mechanics-based gradient enhanced damage model

Here, this study aims to examine modeling flaw sensitivity in elastomers. The direct incorporation of polymer chain statistical mechanics considerations into a continuum stretch-based gradient-enhanced damage formulation, in turn, allows a representation of diffuse chain damage and fracture events that align with known micromechanical mechanisms. Through a series of numerical experiments, we simulate crack propagation and extract the fracture energy as an output of the model, while keeping track of the micromechanical signatures of diffuse chain damage that accommodate fracture propagation and eventually influence flaw sensitivity. Finally, by combining the fracture toughness and the work to rupture, we identify a fractocohesive length of the material, corresponding to the full width of the damage process zone. As the damage-to-fracture cascade in the proposed GED model is influenced by the introduction of a length scale associated with network imperfection and long-range load transfer, the emerging relationship of the two length scales is discussed, providing a potential link between microscopic damage mechanisms and the observed macroscopic fracture response.

36 MATERIALS SCIENCE↗