Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fracture strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

SiC fiber reinforced reaction-bonded Si3N4 composites

A technique for fabricating strong and tough SiC fiber reinforced reaction bonded Si3N4 matrix composites (SiC/RBSN) was developed. Using this technique, composites containing approximately 23, 30, and 40 volume fractions of aligned 140 micron diameter, chemically vapor deposited SiC fibers were fabricated. The room temperature physical and mechanical properties were evaluated. The results for composite tensile strength, bend strength, and fracture strain indicate that the composite displays excellent properties when compared with the unreinforced matrix of comparable porosity. The composite stress at which the matrix first cracks and the ultimate composite fracture strength increase with increasing volume fraction of fibers, and the composite fails gracefully. The mechanical property data of this ceramic composite are compared with similar data for unreinforced commercially available Si3N4 materials and for SEP SiC/SiC composites.

Bhatt, Ramakrishna T.↗
NASA NTRS1976

Effect of water and ice on strength and fracture toughness of intermittently bonded boron-epoxy composites

The effects of water and ice on the strength and fracture toughness of boron-epoxy composites with polyurethane intermittent bonding have been investigated. Neither simple soaking in water nor soaking followed by freezing and thawing have marked effects on the strength of the fully-coated composites, but they have disastrous effects on the uncoated composites. Toughness is affected only marginally, with some small reductions in the fully-coated samples, and with essentially no effect on the uncoated composites. An analysis is presented which explains adequately the experimental strength and toughness results obtained, and which is based on an argument that water absorption reduces the interfacial shear strength only of the uncoated areas and not those regions coated by the polyurethane varnish. The results indicate that the advantages of appropriate intermittent bonding (i.e., high strength combined with high toughness) are retained in wet conditions so that such composites may be favorably used in such adverse environmental conditions.

Atkins, A. G.↗
NASA NTRS1988

Hafnia-rich mixed oxide ceramics of the system HfO2-ZrO2-TiO2 for heaters and heat exchangers in electrothermal thrusters: The effects of titania on selected electrical and mechanical properties of Hafnia-rich mixed oxides in the system Hafnia-Zirconia-Titania, volume 1

A study of the effects of titania on selected properties of hafnia-rich mixed oxides in the system hafnia-zirconia-titania (HZT) was made in the region 5 to 20 mol percent titania. The studied properties included electrical conductivity, thermal expansion, and fracture strength and toughness. The effects of titania on the properties were studied for the reduced state as well as the oxidized state of the sintered mixed oxides. X-ray analysis showed that the materials were not always single phase. The oxidized compositions went from being monoclinic solid solutions at low titania additions to having three phases (two monoclinic and a titanate phase) at high additions of titania. The reduced compositions showed an increasing cubic phase presence mixed with the monoclinic phase as titania was added. The electrical conductivity increased with temperature at approximately 0.1 mhos/cm at 1700 C for all compositions. The thermal expansion coefficient decreased with increasing titania as did the monoclinic to tetragonal transformation temperature. The fracture strength of the oxidized bars tended to decrease with the addition of titania owing to the presence of the second phase titania. The fracture strength of the reduced bars exhibited a minimum corresponding to a two-phase region of monoclinic and cubic phases. When the second phases were suppressed, the titania tended to increase the fracture strength slightly in both the oxidized and reduced states. The fracture toughness followed similar trends.

Staszak, Paul Russell↗
NASA NTRS1982

Investigating reliability attributes of silicon photovoltaic cells - An overview

Reliability attributes are being developed on a wide variety of advanced single-crystal silicon solar cells. Two separate investigations: cell-contact integrity (metal-to-silicon adherence), and cracked cells identified with fracture-strength-reducing flaws are discussed. In the cell-contact-integrity investigation, analysis of contact pull-strength data shows that cell types made with different metallization technologies, i.e., vacuum, plated, screen-printed and soldered, have appreciably different reliability attributes. In the second investigation, fracture strength was measured using Czochralski wafers and cells taken at various stages of processing and differences were noted. Fracture strength, which is believed to be governed by flaws introduced during wafer sawing, was observed to improve (increase) after chemical polishing and other process steps that tend to remove surface and edge flaws.

Royal, E. L.↗
NASA NTRS1991

Comparison of Weibull strength parameters from flexure and spin tests of brittle materials

Fracture data from five series of four point bend tests of beam and spin tests of flat annular disks were reanalyzed. Silicon nitride and graphite were the test materials. The experimental fracture strengths of the disks were compared with the predicted strengths based on both volume flaw and surface flaw analyses of four point bend data. Volume flaw analysis resulted in a better correlation between disks and beams in three of the five test series than did surface flaw analysis. The Weibull (moduli) and characteristic gage strengths for the disks and beams were also compared. Differences in the experimental Weibull slopes were not statistically significant. It was shown that results from the beam tests can predict the fracture strength of rotating disks.

Holland, Frederic A., Jr.↗
NASA NTRS2014

Multilayer Pressure Vessel Materials Testing and Analysis Phase 2

To provide NASA with a suite of materials strength, fracture toughness and crack growth rate test results for use in remaining life calculations for the vessels described above, Southwest Research Institute® (SwRI®) was contracted in two phases to obtain relevant material property data from a representative vessel. An initial characterization of the strength, fracture and fatigue crack growth properties was performed in Phase 1. Based on the results and recommendations of Phase 1, a more extensive material property characterization effort was developed in this Phase 2 effort. This Phase 2 characterization included additional strength, fracture and fatigue crack growth of the multilayer vessel and head materials. In addition, some more limited characterization of the welds and heat affected zones (HAZs) were performed. This report

Popelar, Carl F.↗
NASA NTRS1992

Strength and fracture of glass in the lunar environment

Due to the lack of water on the moon, the effects of hydrolytic depolymerization - stress corrosion cracking - will be nonexistent in glasses produced and used on the moon. This would seem to make lunar glass very attractive for use in a wide variety of space engineering applications. We have applied the equation that describes stress corrosion cracking to lunar glass to show that, indeed, decreasing water vapor pressure results in an increase in strength. Experimental results on simulated lunar glass confirm this. The stress corrosion equation predicts an extremely high strength for glasses produced on the moon. This equation, however, cannot be applied to glasses under anhydrous conditions. In an environment completely devoid of water, the strength of glass will be determined by the fracture of the glass at the tip of a flaw, without the corrosive effects of water. Under this condition, in accordance with fracture theory, the strength of the glass will primarily be a function of the flaw size. Our experimental results show that the presence of surface flaws is more detrimental to the strength of simulated lunar glass than the effect of hydrolytic depolymerization.

Allen, Daniel D.↗
NASA NTRS1982

Graphite fiber surface treatment to improve impact strength and fracture resistance in subsequent composites

Graphite (or carbon) fiber composite impact strength improvement was attempted by modifying the fiber surface. Elastomeric particles were made into lattices and deposited ionically on surface treated graphite fiber in an attempt to prepare a surface containing discrete rubber particles. With hard, nonelastomeric polystyrene discrete particle coverage was achieved. All the elastomeric containing lattices resulted in elastomer flow and filament agglomeration during drying.

Paul, J. T., Jr.↗
NASA NTRS1991

Elevated temperature mechanical behavior of monolithic and SiC whisker-reinforced silicon nitrides

The mechanical behavior of a 30 volume percent SiC whisker reinforced silicon nitride and a similar monolithic silicon nitride were measured at several temperatures. Measurements included strength, fracture toughness, crack growth resistance, dynamic fatigue susceptibility, post oxidation strength, and creep rate. Strength controlling defects were determined with fractographic analysis. The addition of SiC whiskers to silicon nitride did not substantially improve the strength, fracture toughness, or crack growth resistance. However, the fatigue resistance, post oxidation strength, and creep resistance were diminished by the whisker addition.

Salem, Jonathan A.↗
NASA NTRS1983

Experimental deformation of polycrystalline H2O ice at high pressure and low temperature - Preliminary results

A preliminary study is carried out of involving 70 constant strain deformation tests on pure polycrystalline H2O ice under conditions covering most of the stability field of ice I sub h. Brittle failure of I sub h is found to be promoted by lower P, lower T, and higher strain rates. Ductile flow is found to be promoted by higher P, higher T, and lower strain rates. The brittle failure of ice I sub h is found to be most unusual. The fracture strength is a positive function of P only below 50 MPa. At pressures greater than this, the fracture strength is independent of P, and the fracture plane lies approximately 45 deg from the load axis. It is believed that existing extrapolation based on existing experimental data to Ganymede and Callisto may be badly in error.

Durham, W. B.↗
NASA NTRS1972

Effect of metallurgical structure and properties on adhesion and friction behavior of cobalt alloys

The metallurgical structure and some of the mechanical properties of two cobalt alloys, cobalt-50% iron and cobalt-25% molybdenum-10% chromium, were determined under various heat treated conditions. The mechanical properties of the bcc disordered Co-50Fe alloy, which was found to be very brittle, indicated an exceedingly low fracture strength, low hardness, and very weak grain boundary strength. Ordering by suitable heat treatment only produced a more brittle material with a lower fracture strength and a slightly higher hardness value. Work hardening was found to produce a finer grain structure and a greater grain boundary strength. Tensile properties were examined. It was found that the Co-25Mo-10Cr alloy was difficult to place in the alpha Co solid solution condition, which limited the ability to use precipitation as a hardening reaction. Over two hundred adhesion cycles from zero contact load, to maximum load, to fracture were conducted between couples for each of the above alloys in an ultrahigh vacuum system which would permit the sample surfaces to be cleaned of all contaminant layers. In the Co-50Fe case, the calculated fracture stress from the adhesion tests showed values in the range of 80 to 150 k.s.i., which is about ten times greater than the values from tension tests.

Keller, D. V., Jr.↗
NASA NTRS1973

The effects of shot-peening residual stresses on the fracture and crack growth properties of D6AC steel

The fracture strength and cyclic crack-growth properties of surface-flawed, shot-peened D6AC steel plate were investigated. For short crack lengths (up to 1.5mm) simple linear elastic fracture mechanics - based only on applied loading - did not predict the fracture strengths. Also, Paris' Law for cyclic crack growth did not correlate the crack-growth behavior. To investigate the effect of shot-peening, additional fracture and crack-growth tests were performed on material which was precompressed to remove the residual stresses left by the shot-peening. Both tests and analysis show that the shot-peening residual stresses influence the fracture and crack-growth properties of the material. The analytical method of compensating for residual stresses and the fracture and cyclic crack-growth test results and predictions are presented.

Elber, W.↗
NASA NTRS1974

Effects of shot-peening residual stresses on the fracture and crack-growth properties of D6AC steel

The fracture strength and cyclic crack-growth properties of surface-flawed, shot-peened D6AC steel plate were investigated. For short crack lengths (up to 1.5 mm) simple linear elastic fracture mechanics - based only on applied loading - did not predict the fracture strengths. Also, Paris' Law for cyclic crack growth did not correlate the crack-growth behavior. To investigate the effect of shot-peening, additional fracture and crack-growth tests were performed on material which was precompressed to remove the residual stresses left by the shot-peening. Both tests and analysis show that shot-peening residual stresses influence the fracture and crack-growth properties of the material. This report presents the analytical method of compensating for residual stresses and the fracture and cyclic crack-growth test results and predictions.

Elber, W.↗
NASA NTRS1985

Glass breaking strength: The role of surface flaws and treatments

Although the intrinsic strength of silicon dioxide glass is of the order of 10 to the 6th power lb/sq in, the practical strength is roughly two orders of magnitude below this theoretical limit, and depends almost entirely on the surface condition of the glass, that is, the number and size of flaws and the residual surface compression (temper) in the glass. Glass parts always fail in tension when these flaws grow under sustained loading to some critical size. Research associated with glass encapsulated crystalline-Si photovoltaic (PV) modules has greatly expanded our knowledge of glass breaking strength and developed sizeable data base for commercially available glass types. A detailed design algorithm is developed for thickness sizing of rectangular glass plates subject to pressure loads. Additional studies examine the strength of glass under impact loading conditions such as that caused by hail. Although the fundamentals of glass breakage are directly applicable to thin film modules, the fracture strength of typical numerical glass must be replaced with data that reflect the high temperature tin oxide processing, laser scribing, and edge processing peculiar to thin film modules. The fundamentals of glass breakage applicable to thin film modules and preliminary fracture strength data for a variety of 1 ft square glass specimens representing preprocessed and post processed sheets from current amorphous-Si module manufacturers are presented.

Moore, D.↗
NASA NTRS1989

Investigation of Weibull statistics in fracture analysis of cast aluminum

The fracture strengths of two large batches of A357-T6 cast aluminum coupon specimens were compared by using two-parameter Weibull analysis. The minimum number of these specimens necessary to find the fracture strength of the material was determined. The applicability of three-parameter Weibull analysis was also investigated. A design methodology based on the combination of elementary stress analysis and Weibull statistical analysis is advanced and applied to the design of a spherical pressure vessel shell. The results from this design methodology are compared with results from the applicable ASME pressure vessel code.

Holland, Frederic A., Jr.↗
NASA NTRS1989

Investigation of Weibull statistics in fracture analysis of cast aluminum

The fracture strengths of two large batches of A357-T6 cast aluminum coupon specimens were compared by using two-parameter Weibull analysis. The minimum number of these specimens necessary to find the fracture strength of the material was determined. The applicability of three-parameter Weibull analysis was also investigated. A design methodolgy based on the combination of elementary stress analysis and Weibull statistical analysis is advanced and applied to the design of a spherical pressure vessel shell. The results from this design methodology are compared with results from the applicable ASME pressure vessel code.

Holland, F. A., Jr.↗
NASA NTRS1983

The effect of extreme temperatures on the elastic properties and fracture behavior of graphite/polyimide composites

The influence of elevated and cryogenic temperatures on the elastic moduli and fracture strengths of several C6000/PMR-15 and C6000/NR-15082 laminates was measured. Tests were conducted at -157 C, 24 C, and 316 C (-250 F, 75 F, and 600 F). Both notched and unnotched laminates were tested. The average stress failure criterion was used to predict the fracture strength of quasi-isotropic notched laminates.

Morris, D. H.↗
NASA NTRS1984

The effect of extreme temperatures on the elastic properties and fracture behavior of graphite/polyimide composites

The influence of elevated and cryogenic temperatures on the elastic moduli and fracture strengths of several C6000/PMR-15 and C6000/NR-15082 laminates was measured. Tests were conducted at -157 C, 24 C, and 316 C (-250 F, 75 F, and 600 F). Both notched and unnotched laminates were tested. The average stress failure criterion was used to predict the fracture strength of quasi-isotropic notched laminates.

Morris, D. H.↗