Search NASA⌕ Search

SEARCH · Search NASA

Results for “Free surface velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Environmental controls on isolated convection during the Amazonian wet season

The Amazon rainforest is a vital component of the global climate system, influencing the hydrological cycle and tropical circulation. However, understanding and modeling the evolution of convection in this region remain a scientific challenge. Here, we assess the environmental conditions associated with shallow, congestus, and isolated deep convection days during the wet season (December to April), employing measurements from the Green Ocean Amazon 2014–2015 (GoAmazon2014/5) experiment and large-scale wind fields from the constrained variational analysis. Composites of deep days show moister than average conditions below 3 km early in the morning. Analyzing the water budget at the surface through observations only, we estimated the water vapor convergence term as a residual of the water balance closure. Convergence remains nearly zero during the deep days until early afternoon (13:00 LST), when it becomes a dominant factor in the water budget. At 14:00 LST, the deep days experience a robust upward large-scale vertical velocity, especially above 4 km, which supports the shallow-to-deep convective transition occurring around 16:00–17:00 LST. In contrast, shallow and congestus days exhibit drier pre-convective conditions, along with diurnal water vapor divergence and large-scale subsidence that extend from the surface to the lower free troposphere. Moreover, afternoon precipitation exhibits the strongest linear correlation (0.6) with large-scale vertical velocity, nearly double the magnitude observed for other environmental factors, even moisture, at different levels and periods of the day. Precipitation also exhibits a moderate increase with low-level wind shear, while upper-level shear has a relatively minor negative impact on convection.

Environmental Sciences & Ecology↗
DOE OSTI2025

Stokes-dependent droplet collection efficiency on a NACA 0012 airfoil from droplet-informed simulations with statistical overloading

Accurate modelling of ice accretion on aircraft wings requires analysing droplet impingement on the surface to optimize the design of ice-protection systems. We perform Euler–Lagrange simulations of a droplet-laden flow impinging on a NACA 0012 airfoil. Our study includes water droplets with eight discrete sizes ranging from 1 to 160 microns. We vary the free-stream velocity of the incoming airflow in the range 60 ≤ U ≤ 240 m s −1 and the chord length of the airfoil in the range 0.5 ≤ c ≤ 2 m. Due to the dilute nature of supercooled clouds, one-way coupling is used in the simulations. The effects of droplet breakup and collision are also neglected. To reduce the computational cost, we employ statistical overloading of droplets, allowing us to simulate millions of impinging droplets in a time span on the order of milliseconds. Our results show that the droplet collection efficiency, which measures the likelihood of droplet impingement on the airfoil surface, increases with droplet size and free-stream velocity but decreases with airfoil size. We demonstrate that collection efficiency, impingement velocity and impingement angle are primarily dictated by a single non-dimensional parameter, the droplet Stokes number. We also identify a critical stagnation-streamline Stokes number below which impingements do not occur and use it to estimate the minimum droplet size for impingement. In addition, we observe droplet behaviour to become Stokes number independent at large values of the Stokes number. This article is part of the theme issue ‘Heat and mass transfer in frost and ice’.

Science & Technology - Other Topics↗
DOE OSTI2022

Quantifying Equiaxed vs Epitaxial Solidification in Laser Melting of CMSX-4 Single Crystal Superalloy

The competition between epitaxial vs. equiaxed solidification has been investigated in CMSX-4 single crystal superalloy during laser melting as practiced in additive manufacturing. Single-track laser scans were performed on a powder-free surface of directionally solidified CMSX-4 alloy with several combinations of laser power and scanning velocity. Electron backscattered diffraction (EBSD) mapping facilitated identification of new orientations, i.e., “stray grains” that nucleated within the fusion zone along with their area fraction and spatial distribution. Using high-fidelity computational fluid dynamics simulations, both the temperature and fluid velocity fields within the melt pool were estimated. This information was combined with a nucleation model to determine locations where nucleation has the highest probability to occur in melt pools. In conformance with general experience in metals additive manufacturing, the as-solidified microstructure of the laser-melted tracks is dominated by epitaxial grain growth; nevertheless, stray grains were evident in elongated melt pools. It was found that, though a higher laser scanning velocity and lower power are generally helpful in the reduction of stray grains, the combination of a stable keyhole and minimal fluid velocity further mitigates stray grains in laser single tracks.

36 MATERIALS SCIENCE↗
DOE OSTI2025

FreeMHD: Validation and verification of the open-source, multi-domain, multi-phase solver for electrically conductive flows

The extreme heat fluxes in the divertor region of tokamaks may require an alternative to solid plasma-facing components, for the extraction of heat and the protection of the surrounding walls. Flowing liquid metals are proposed as an alternative, but raise additional challenges that require investigation and numerical simulations. Free surface designs are desirable for plasma-facing components, but steady flow profiles and surface stability must be ensured to limit undesirable interactions with the plasma. Previous studies have mainly used steady-state, 2D, or simplified models for internal flows and have not been able to adequately model free-surface liquid metal (LM) experiments. Therefore, FreeMHD has been recently developed as an open-source magnetohydrodynamics (MHD) solver for free-surface electrically conductive flows subject to a strong external magnetic field. The FreeMHD solver computes incompressible free-surface flows with multi-region coupling for the investigation of MHD phenomena involving fluid and solid domains. The model utilizes the finite-volume OpenFOAM framework under the low magnetic Reynolds number approximation. FreeMHD is validated using analytical solutions for the velocity profiles of closed channel flows with various Hartmann numbers and wall conductance ratios. Next, experimental measurements are then used to verify FreeMHD, through a series of cases involving dam breaking, 3D magnetic fields, and free-surface LM flows. These results demonstrate that FreeMHD is a reliable tool for the design of LM systems under free surface conditions at the reactor scale. Furthermore, it is flexible, computationally inexpensive, and can be used to solve fully 3D transient MHD flows.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Liquid lithium divertor analysis using coupled plasma material interaction model

A liquid lithium divertor can improve performance of future fusion devices by creating efficient power exhaust and improving the energy confinement via pumping of the hydrogen isotopes. In addition, significantly higher heat fluxes can be handled if controlled vapor shielding is used to redistribute the divertor heat flux over a wider area. Design and optimization of such a system calls for an analysis model which includes a strong two-way coupling between the plasma and divertor material. The incoming plasma heat and particle flux will affect the divertor surface temperature, which is a defining factor of the lithium evaporative and sputtered flux going into the plasma. Results of the coupled model based on the plasma edge code SOLPS-ITER and the computational fluid dynamics (CFD) code ANSYS-CFX will be presented for different configurations. An analytical slab flow model is used as a heat transfer boundary condition for SOLPS, defining particle flux from the wall via calculation of the surface temperature. At the final step, results of the SOLPS analysis are verified using a 3D CFD magnetohydrodynamics (MHD) analysis which uses heat and particle flux from SOLPS as a boundary condition. In addition to plasma heat flux, both analytical and CFD temperature models include several plasma material interaction effects, such as lithium evaporation, condensation and sputtering based on deuterium target flux. New adatom sputtering model based on the available experimental data is presented. Analytical model is expanded to include free surface axisymmetric configurations. Results of parametric studies of the divertor configurations with different lithium inlet temperature and velocity will be presented leading to the optimal design resulting in the lowest possible lithium contamination in the core.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Large-Eddy Simulation of Flow Over Boeing Gaussian Bump Using Multiagent Reinforcement Learning Wall Model: Preprint

We develop a wall model for large-eddy simulation (LES) that takes into account various pressure-gradient effects using multi-agent reinforcement learning. The model is trained using low-Reynolds-number flow over periodic hills with agents distributed on the wall at various computational grid points. It utilizes a wall eddy-viscosity formulation as the boundary condition to apply the modeled wall shear stress. Each agent receives states based on local instantaneous flow quantities at an off-wall location, computes a reward based on the estimated wall-shear stress, and provides an action to update the wall eddy viscosity at each time step. The trained wall model is validated in wall-modeled LES of flow over periodic hills at higher Reynolds numbers, and the results show the effectiveness of the model on flow with pressure gradients. The analysis of the trained model indicates that the model is capable of distinguishing between the various pressure gradient regimes present in the flow. To further assess the robustness of the developed wall model, simulations of flow over the Boeing Gaussian bump are conducted at a Reynolds number of 2 x 10^6, based on the free-stream velocity and the bump width. The results of mean skin friction and pressure on the bump surface, as well as the velocity statistics of the flow field, are compared to those obtained from equilibrium wall model (EQWM) simulations and published experimental data sets. The developed wall model is found to successfully capture the acceleration and deceleration of the turbulent boundary layer on the bump surface, providing better predictions of skin friction near the bump peak and exhibiting comparable performance to the EQWM with respect to the wall pressure and velocity field. We also conclude that the subgrid-scale model is crucial to the accurate prediction of the flow field, in particular the prediction of separation.

boundary layer↗
DOE OSTI2022

TEAMER: DAISY Flow-noise Testing (Abstract)

Evaluating impacts of marine energy devices is generally difficult given the dynamic environment where these devices need to be placed. The University of Washington’s (UW) DAISY (The Drifting Acoustic Instrumentation SYstem) is designed to measure radiated noise around marine energy converters operating in energetic waves and currents. In currents, a primary limitation for measurement fidelity at low frequencies (< 100 Hz) is the potential for non-propagating “flow-noise” to mask propagating sound and inflate estimates of the radiated noise from marine energy converters at frequencies that overlap with hearing sensitivities of fish and some marine mammals. While free-drifting measurements help to minimize the relative velocity that produces flow-noise, significant levels were still observed during initial DAISY tests. This motivated the development of a fabric “flow shield” around the hydrophone that disrupts both flow-noise generation mechanisms proposed by the initial tests. First, the flow shield is a source of substantial drag which keeps the hydrophone package moving with the approximate velocity of the surrounding water, compensating for differential wind or current forcing on the surface expression. By minimizing relative velocity around the hydrophone, turbulence shed by the hydrophone is also minimized. Second, the flow shield creates a largely quiescent pocket around the hydrophone, minimizing advection of free stream turbulence over the hydrophone element. Field data collected in these experiments will test effectiveness of these flow shields and provide quantitative data use and deployment.

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Hyporheic Exchange in Sand Dunes Under a Freely Deforming River Water Surface

Bedform-driven hyporheic exchange is conditioned by the head gradients at the sediment-water interface. Local exchange phenomena between the surface and the subsurface are often driven by the dynamic forces related to the velocity distributions around sediment waves. In open channels, the static forces are represented by the water depth, yet most computational fluid dynamics models use a rigid-lid approximation. Here, we investigated whether and when the deformation of the river’s free-surface influences bedform-driven hyporheic exchange. This was done through simulations of coupled open channel and hyporheic flows with the air-water interface modeled either as a free-surface or a rigid-lid across increasing subcritical Froude numbers from ~0.05 to ~0.95. The normalized hyporheic flux was higher when considering free-surface deformation across most of the range of Froude numbers considered. When the Froude number was larger than 0.6 and smaller than 0.85, both hydrostatic and nonhydrostatic-driven fluxes increased significantly compared to the rigid-lid approach and the total flux was about five times that predicted with the rigid-lid. These results indicate that bedform-driven hyporheic fluxes are underestimated in most studies that use a rigid-lid assumption in subcritical flows.

58 GEOSCIENCES↗
DOE OSTI2020

2-D moving mesh modeling of lithium dryout in open surface liquid metal flow applications

Liquid lithium displays increasing promise as a replacement for solid plasma facing components (PFCs) in fusion device applications. The Liquid Metal Infused Trench (LiMIT) system, developed at the University of Illinois (UIUC), has demonstrated how thermoelectric magnetohydrodynamics (TEMHD) can be harnessed to drive liquid lithium flow in an open surface PFC. However, in the highest heat flux applications, large local acceleration is created via TEMHD, and the sudden increase in velocity can cause the liquid level to expose the underlying solid, eliminating the protective benefits of the lithium. In order to study potential mitigation strategies, a 2-D COMSOL Multiphysics model was developed using the moving mesh module to capture free surface flow. The model depicts the development of the dryout phenomenon for 2 test cases – slow (1 cm/s) and medium (10 cm/s) flow in 5 mm deep trenches – including the liquid level reduction under the high heat flux and the pileup of slower flow both upstream and downstream of the heat stripe. The effectiveness of trench shaping dryout mitigation strategies is examined. For the slow flow case, it is shown that a 1.8 mm ledge placed under the heat stripe will stop dryout, and for the medium flow case, a 2.7 mm ledge is required to mitigate the effect. This model can be used to identify strategies for increasing the viable heat load for open surface liquid lithium PFCs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

An implicit solution for Asay foil trajectories generated by separable, sustained-production ejecta source models

We present a simple implicit solution for the time-dependent trajectory of a thin Asay foil ejecta diagnostic for the general case where the impinging ejecta cloud is generated by a source function characterized by an arbitrary (sustained) time dependence and a time-independent (stationary) particle velocity distribution. In the limit that the source function time dependence becomes a delta function, this solution—which is amenable to rapid numerical calculations of arbitrary accuracy—exactly recovers a previously published solution for the special case of instantaneous ejecta production. We also derive simple expressions for the free-surface arrival (catch-up) time as well as the true ejecta areal mass accumulation on the accelerating foil and place bounds on the level of error incurred when applying instant-production mass solutions to a sustained-production trajectory. We demonstrate these solutions with example calculations for hypothetical source functions spanning a wide range of ejecta production durations, velocity distributions, and temporal behaviors. These calculations demonstrate how the foil trajectory is often insensitive to the temporal dependence of the source function, instead being dominated by the velocity distribution. We quantify this insensitivity using a “compatibility score” metric. Under certain conditions, one may capitalize upon this insensitivity to obtain a good approximation of the second integral of the velocity distribution from the observed foil trajectory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

A Hybrid Lagrangian/Eulerian Collocated Velocity Advection and Projection Method for Fluid Simulation

Abstract We present a hybrid particle/grid approach for simulating incompressible fluids on collocated velocity grids. Our approach supports both particle‐based Lagrangian advection in very detailed regions of the flow and efficient Eulerian grid‐based advection in other regions of the flow. A novel Backward Semi‐Lagrangian method is derived to improve accuracy of grid based advection. Our approach utilizes the implicit formula associated with solutions of the inviscid Burgers’ equation. We solve this equation using Newton's method enabled by C 1 continuous grid interpolation. We enforce incompressibility over collocated, rather than staggered grids. Our projection technique is variational and designed for B‐spline interpolation over regular grids where multiquadratic interpolation is used for velocity and multilinear interpolation for pressure. Despite our use of regular grids, we extend the variational technique to allow for cut‐cell definition of irregular flow domains for both Dirichlet and free surface boundary conditions.

Gagniere, S.↗
DOE OSTI2021

Optical and electrochemical effects of H 2 and O 2 bubbles at upward-facing Si photoelectrodes

The effects of the size, contact-angle, and coverage of gas bubbles on solar fuels devices were characterized at cm-scale, upward-facing planar and microwire-array Si photoelectrodes in stagnant electrolytes. Experimental measurements were supported by ray-tracing simulations of surface attached gas bubble films. A dilute, redox-active tracer allowed for the quantification of the mass-transport effects of bubble coverage during photoanodic O 2 (g) evolution at upward-facing photoanodes in 1.0 M KOH(aq.). Measurements of the gas coverage at upward-facing p-Si photocathodes in 0.50 M H 2 SO 4 (aq.) allowed for the nucleation rate and contact angle of H 2 (g) bubbles to be evaluated for systems having various surface free energies. Under simulated solar illumination, the rapid departure of small O 2 (g) bubbles produced stable photocurrents at upward-facing oxygen-evolving Si photoanodes and yielded increased mass-transport velocities relative to a stagnant electrolyte, indicating that bubbles can provide a net benefit to the photoelectrochemical performance of an upward-facing photoanode in solar fuels devices.

14 SOLAR ENERGY↗
DOE OSTI2023

Niowave Neutron Source Converter: Lead-Bismuth-Eutectic (LBE) Windowless Target Design and Evaluation

Los Alamos National Laboratory (LANL) is working with Niowave on the design and evaluation of their lead-bismuth-eutectic (LBE) windowless target (i.e., neutron source converter). Niowave plans to use 200 kW electron beam at 40 MeV beam energy to produce neutrons by photonuclear reaction with LBE. Then, the neutrons undergo fission at the surrounding uranium target assembly (UTA) to produce Molybdenum 99 (Mo-99) as a fission product, which eventually decays to Technetium-99 (Tc-99m). Tc-99m is one of important radioisotopes that is used for medical diagnostics. LANL conducted 3D multiphysics analysis for the Niowave neutron converter design and provided design assessment in thermohydraulic aspects. LANL conducted radiation transport calculations using Monte-Carlo N-Particle (MCNP) code with unstructured meshing scheme. The 3D volumetric heating profiles in the LBE and Stainless-Steel (SS) housing were imported into multiphase computational fluid dynamics (CFD) to obtain 3D temperature profiles of LBE and SS through conjugate heat transfer (CHT) analysis. The key findings are: LBE film thickness at the center of the beam is approximately 1.6 cm with a maximum LBE velocity of approximately 1.8 m/s, which is below a 2 m/s limit to avoid erosion issues on supporting structures; Heat deposition in the LBE peaks at ~1 cm depth from the LBE free-surface because of the forward interactions of electron, photon, and neutron with LBE; LBE maximum temperature is ~360 °C, which is below LBE evaporation initiative temperature, ~450 °C; LBE-SS interface temperature is ~350 °C, which is below the safety thermal limit to prevent severe corrosion on SS. The results indicate that Niowave’s neutron converter design satisfies both hydraulic and thermal criteria for safe operation. By virtue of such computational analysis, Niowave can move toward establishing an experimental setup to experimentally test their LBE neutron converter. The following sections describe the detailed work done by LANL.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Interpreting the Diurnal Cycle of Clouds and Precipitation in the ARM GoAmazon Observations: Shallow to Deep Convection Transition

The Green Ocean Amazon (GoAmazon) 2014/5 field campaign data are used to study the diurnal cycle of clouds and precipitation. Through a careful classification of days with shallow cumulus, congestus and deep convection, we investigate the major differences among locally generated convection regimes and the most important environmental factors governing the shallow-to-deep convection transition. On shallow cumulus days, a greater sensible heat flux drives deeper boundary layer growth, which entrains drier free-tropospheric air and lowers the relative humidity, thus leading to a significantly higher cloud base than those on days with deeper convection. Congestus and deep convection regimes exhibit distinct cloud top height distributions with noticeable differences in the vertical wind shear in the mid-troposphere, suggesting an important role of wind shear in limiting the vertical extent of convection. On deep convection days, with preexisting nocturnal convection or cold-pools from external disturbances, the timing of peak surface precipitation (12:00–13:00 LST) tends to be in-phase with the diurnal variation in surface fluxes. However, it takes longer for local deep convection to develop without these disturbances. A plume model with thermodynamic and dynamical constraints is developed to explore the relative importance of various convection-controlling factors. Initial cloud-base vertical velocity and buoyancy are important in helping parcels ascend to the level of free convection (LFC). After parcels reach the LFC, entrainment of environmental air and lower free troposphere humidity become crucial in determining cloud top. Entrainment rate differentiates among convection regimes, which may be tied to the cloud size distribution at cloud base.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Remote Fiber Based Velocimeter For Interface Strength Measurements

The understanding of the performance of nuclear reactor plate fuels is essential when developing new fuel systems. The condition of pre and post irradiated plate fuels must be characterized effectively and efficiently prior to irradiation and then post irradiation within a high rad environment. The post characterization work must be performed remotely and in an environment hostile to instrumentation. Laser based characterization methods provide the capability to be remote and robust within a hot-cell environment. Laser based characterization can provide high spatial resolution appropriate for scanning and imaging large areas. The INL is currently developing a laser shock system for Post Irradiation Examination (PIE) station for use in the Hot Fuel Examination Facility (HFEF) at the INL. The laser shock system is designed to characterize fuel to cladding and cladding to cladding interface strength. The laser shock-technique induces large amplitude shock waves to mechanically characterize interfaces such as the fuel-clad interface. The shock wave propagates as a compressional wave through the fuel plate to the free (unconfined) backside surface and is reflected back through the test plate as a rarefaction (tensile) wave. This rarefaction wave is the physical mechanism that produces internal delamination failure. The focus or this paper is on the accurate measurement of surface velocity to quantify the amount of energy traveling through the interfaces to the back surface of the fuel plate. The original fiber based velocimeter design was biased by parasitic back reflections. This paper will discuss the discovery of the back-reflection issue and the design changes to resolve the issue. Supporting data will be presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

In situ formation of pseudohalide anions induced by humid air and light passivates formamidinium‐based halide perovskites

Abstract Metal halide perovskites based on formamidinium (FA), or FA‐rich compositions have shown great promise for high‐performance photovoltaics. A deeper understanding of the impact of ambient conditions (e.g., moisture, oxygen, and illumination) on the possible reactions of FA‐based perovskite films and their processing sensitivities has become critical for further advances toward commercialization. Herein, we investigate reactions that take place on the surface of the FA 0.7 Cs 0.3 , mixed Br/I wide bandgap perovskite thin films in the presence of humid air and ambient illumination. The treatment forms a surface layer containing O, OH, and N‐based anions. We propose the latter originates from formamidine trapped at the perovskite/oxide interface reacting further to cyanide and/or formamidinate—an understudied class of pseudohalides that bind to Pb. Optimized treatment conditions improve photoluminescence quantum yield owing to both reduced surface recombination velocity and increased bulk carrier lifetime. The corresponding perovskite solar cells also exhibit improved performance. Identifying these reactions opens possibilities for better utilizing cyanide and amidinate ligands, species that may be expected during vapor processing of FA‐based perovskites. Our work also provides new insights into the self‐healing or self‐passivating of MA‐free perovskite compositions where FA and iodide damage could be partially offset by advantageous reaction byproducts. image

14 SOLAR ENERGY↗
DOE OSTI2025

Reactive Transport Modeling of Hydrogen Production from Serpentinization of Olivine

Hydrogen production from serpentinization of ultramafic rocks represents a promising natural pathway for generating carbon-free energy, yet its kinetics and controlling factors remain incompletely understood. A key challenge in advancing serpentinization research lies in the heterogeneity of porosity and permeability in rocks, which leads to nonuniform fluid velocity fields, as well as uncertainties in estimating reactive surface area and identifying appropriate mineral reaction equilibria. Additional complexities arise from the role of dissolved SiO 2 , Fe 2+ /Fe 3+ partitioning, and the limited effect of pH variations within the strongly alkaline regime on hydrogen yields. These challenges hinder straightforward extrapolation from laboratory tests to practical applications of hydrogen production from natural rocks. Here, in this work, we address these questions using a simulation-based reactive transport modeling framework calibrated against controlled laboratory experiments reported elsewhere. The model couples geochemical kinetics, multiphase flow, and mineralogical feedbacks, enabling systematic evaluation of how surface area, dissolved silica concentration, Fe redox state, temperature, and pressure govern serpentinization and H2 generation. We find that surface area exerts the strongest control on reaction rates and hydrogen yields, while Fe 2+ /Fe 3+ ratios act as secondary modulators. Elevated dissolved silica concentrations suppress hydrogen production but accelerate serpentine precipitation, whereas increasing pH beyond 12 within the strongly alkaline regime produces only marginal gains. Finally, we demonstrate that integrating targeted experiments with calibrated simulations offers a powerful and efficient approach for predicting hydrogen yields and assessing parameter trade-offs in industrial-scale applications. This integration can substantially reduce the experimental burden while improving predictive capability, thereby enhancing both the mechanistic understanding and the practical feasibility of hydrogen production from serpentinization.

08 HYDROGEN↗