SEARCH · Search NASA

Results for “Freestream Mach Number”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1994

Laminar and turbulent flow computations of Type 4 shock-shock interference aerothermal loads using unstructured grids

This report presents computations for the Type 4 shock-shock interference flow under laminar and turbulent conditions using unstructured grids. Mesh adaptation was accomplished by remeshing, refinement, and mesh movement. Two two-equation turbulence models were used to analyze turbulent flows. The mean flow governing equations and the turbulence governing equations are solved in a coupled manner. The solution algorithm and the details pertaining to its implementation on unstructured grids are described. Computations were performed at two different freestream Reynolds numbers at a freestream Mach number of 11. Effects of the variation in the impinging shock location are studied. The comparison of the results in terms of wall heat flux and wall pressure distributions is presented.

Vemaganti, Gururaja R.↗

NASA NTRS1991

Progress toward synergistic hypermixing nozzles

Mean flow measurements were obtained for air-to-air mixing downstream of swept and unswept ramp wall mounted hypermixing nozzle configurations. Aside from the sweep of the ramps, the two nozzle configurations studied are identical. The nozzles inject three parallel supersonic jets at a 15 deg angle (relative to the wind tunnel wall) into a supersonic freestream. Mach number and volume fraction distributions in a transverse plane 11.1 nozzle heights downstream from the nozzle exit plane were measured. Data are presented for a freestream Mach number of three at a matched static pressure condition and also at underexpanded static pressure condition (pressure ratio = 5). Surface oil flow visualization was used to study the near wall flow behavior. The results indicate that the swept ramp injectors produce stronger and larger vortex pairs than the unswept ramp injectors. The increased interaction between the swept ramp model's larger vortex pairs yields better mixing characteristics for this model.

Davis, D. O.↗

NASA NTRS1991

Progress toward synergistic hypermixing nozzles

Mean flow measurements have been obtained for air-to-air mixing downstream of swept and unswept ramp wall-mounted hypermixing nozzle configurations. Aside from the sweep of the ramps, the two nozzle configurations investigated are identical. The nozzles inject three parallel supersonic jets at a 15-deg angle (relative to the wind tunnel wall) into a supersonic freestream. Mach number and volume fraction distributions in a transverse plane 11.1 nozzle heights downstream from the nozzle exit plane were measured. Data are presented for a freestream Mach number of three at a matched static pressure condition and also at an underexpanded static pressure condition (pressure ratio equal to 5). Surface oil flow visualization was used to investigate the near-wall flow behavior. The results indicate that the swept ramp injectors produce stronger and larger vortex pairs than the unswept ramp injectors. The increased interaction between the swept ramp model's larger vortex pairs yields better mixing characteristics for this model.

Davis, D. O.↗

NASA NTRSDate not supplied

Off-Design Analysis of Axisymmetric External-Compression Supersonic Inlets for Mach 1.4 to 2.0

Supersonic axisymmetric, external-compression inlets designed for freestream Mach numbers of Mach 1.4, 1.7, and 2.0 were evaluated to characterize their off-design performance. The inlets were characterized as isolated from the airframe with freestream conditions, engine-face geometry, and flow rates established from a reference NASA commercial aircraft concept. The off-design performance was characterized using computational fluid dynamics (CFD) simulations. The study characterized the off-design performance at the cruise condition for variations in the inlet flow rate, angle-of-attack, and freestream Mach number. Also characterized was the inlet performance at take-off and approach-to-landing conditions for which the use of auxiliary intakes was included. The inlet performance was characterized by the flow rates, total pressure recovery and distortion, and drag. An understanding of the off-design performance of the axisymmetric inlets provides information for the selection of inlets for commercial supersonic aircraft.

Supersonic Inlets↗

NASA NTRSDate not supplied

Off-Design Analysis of Axisymmetric External-Compression Supersonic Inlets for Mach 1.4 to 2.0

Supersonic Inlets↗

NASA NTRS1983

A shock-fitting solution of the supersonic flowfield in a rounded internal corner

A comparison is presented of a computational investigation of the flowfield created by supersonic flow over an internal corner with rounding and experimental results at a freestream Mach number of 4.1. The computational study uses a shock-fitting finite difference scheme with explicit formulation of the transformation to computational coordinates. The solutions calculated agree with previous ones for the sharp corner case and with the experimental investigation results for the rounded corner case. Parametric effects were computed for variations in corner rounding, freestream Mach number, symmetric wedge angle and unsymmetric wedge angle. A region is described over which successful executions were obtained.

Martin, J. A.↗

NASA NTRS1993

CFD code calibration and inlet-fairing effects on a 3D hypersonic powered-simulation model

A three-dimensional (3D) computational study has been performed addressing issues related to the wind tunnel testing of a hypersonic powered-simulation model. The study consisted of three objectives. The first objective was to calibrate a state-of-the-art computational fluid dynamics (CFD) code in its ability to predict hypersonic powered-simulation flows by comparing CFD solutions with experimental surface pressure dam. Aftbody lower surface pressures were well predicted, but lower surface wing pressures were less accurately predicted. The second objective was to determine the 3D effects on the aftbody created by fairing over the inlet; this was accomplished by comparing the CFD solutions of two closed-inlet powered configurations with a flowing-inlet powered configuration. Although results at four freestream Mach numbers indicate that the exhaust plume tends to isolate the aftbody surface from most forebody flowfield differences, a smooth inlet fairing provides the least aftbody force and moment variation compared to a flowing inlet. The final objective was to predict and understand the 3D characteristics of exhaust plume development at selected points on a representative flight path. Results showed a dramatic effect of plume expansion onto the wings as the freestream Mach number and corresponding nozzle pressure ratio are increased.

Huebner, Lawrence D.↗

NASA NTRS1993

CFD Code Calibration and Inlet-Fairing Effects On a 3D Hypersonic Powered-Simulation Model

A three-dimensional (3D) computational study has been performed addressing issues related to the wind tunnel testing of a hypersonic powered-simulation model. The study consisted of three objectives. The first objective was to calibrate a state-of-the-art computational fluid dynamics (CFD) code in its ability to predict hypersonic powered-simulation flows by comparing CFD solutions with experimental surface pressure data. Aftbody lower surface pressures were well predicted, but lower surface wing pressures were less accurately predicted. The second objective was to determine the 3D effects on the aftbody created by fairing over the inlet; this was accomplished by comparing the CFD solutions of two closed-inlet powered configurations with a flowing- inlet powered configuration. Although results at four freestream Mach numbers indicate that the exhaust plume tends to isolate the aftbody surface from most forebody flow- field differences, a smooth inlet fairing provides the least aftbody force and moment variation compared to a flowing inlet. The final objective was to predict and understand the 3D characteristics of exhaust plume development at selected points on a representative flight path. Results showed a dramatic effect of plume expansion onto the wings as the freestream Mach number and corresponding nozzle pressure ratio are increased.

Huebner, Lawrence D.↗

NASA NTRS1996

Improved Models for the Porous Surface with Passive Control

A computational investigation of afterbody flow using a passive control method is conducted. The passive control method consists of a porous surface placed over a plenum. The purpose of the passive control method is to exploit the adverse pressure gradient present in afterbody flow in an attempt to reduce boundary layer separation and afterbody drag. Four different porous wall models are used to model the transpiration velocity in the region of passive control. A three-dimensional, time-dependent, Reynolds-averaged, simplified Navier-Stokes solver, PAB3D, is used to simulate afterbody flow with and without passive control. Three afterbody configurations with boat-tail angles of 10, 20, and 30 deg. are used to obtain two-dimensional solutions with a freestream Mach number of 0.6 and nozzle pressure ratio of 6. The region of passive control was initially placed from 20-60% of the nozzle length. The effect of the porous placement and porous extent is also studied. Baseline (no porosity) two-dimensional solutions are qualitatively similar to experimental data but under-predict the magnitude of the pressure recovery. Results for the subsonic solutions show losses in the pressure recovery for some cases with passive control. Three-dimensional effects are also investigated and seen to be very significant. Three-dimensional baseline solutions, for both sub- and super-critical freestream Mach numbers, compare very favorably with the experimental data in comparison to the two-dimensional solution. Future work is required to examine three-dimensional afterbody flows with passive porosity.

Kraushaar, Sandra L.↗

NASA NTRS1993

Transitional flight characteristics of a geometrically simplified STOVL model

The transitional flight characteristics of a geometrically simplified Short Take-Off Vertical Landing (STOVL) aircraft configuration were measured in the NASA Ames 7- by 10-Foot Wind Tunnel. The experiment was designed to provide detailed data for evaluating the capability of computational fluid dynamics methods to predict the important powered lift flow parameters. The model consists of a 60 deg cropped delta wing planform; a blended fuselage; and tandem, circular, high pressure air jets that exit perpendicular to the flat lower surface. Freestream Mach number is limited to a maximum 0.2. Model angle of attack ranges from -10 deg to +20 deg. The nozzle pressure ratios of both jets are varied between 1 and 3, and the jet exit temperatures are maintained at near ambient conditions. Detailed surface pressure measurements show that suction pressure peaks located on the upper surface of the wing during conventional wingborne flight for angles of attack greater than 5 deg move to the wing lower surface at angles of attack less than 0 deg. A reduction in these suction pressure peaks is observed when the lift jets are operating. With sonic jet exit conditions, a freestream Mach number of 0.14, and 0 deg angle of attack, the jet-induced suckdown is equivalent to a 3.7 deg reduction in angle of attack. Schlieren, laser light sheet flow visualization and total pressure measurements in the jet plumes provide a description of the three-dimensional jet efflux flowfield.

Roth, Karlin R.↗

NASA NTRS2001

Measured and Computed Hypersonic Aerodynamic/Aeroheating Characteristics for an Elliptically Blunted Flared Cylinder

Computational and experimental hypersonic aerodynamic forces and moments and aeroheating levels for Kistler Aerospace Corporation's baseline orbiter vehicle at incidence are presented. Experimental data were measured in ground-based facilities at the Langley Research Center and predictions were performed using the Langley Aerothermodynamic Upwind Relaxation Algorithm code. The test parameters were incidence (-4 to 24 degrees), freestream Mach number (6 to 10),freestream ratio o specific heats (1.2 to 1.4), and freestream Reynolds number (0.5 to 8.0 million per foot). The effects of these parameters on aerodynamic characteristics, as well as the effects of Reynolds number on measured heating levels are discussed. Good agreement between computational and experimental aerodynamic and aeroheating values were observed over the wide range of test parameters examined. Reynolds number and ratio of specific heats were observed to significantly alter the trim L/D value. At Mach 6, laminar flow was observed along the entire windward centerline tip to the flare for all angles and Reynolds numbers tested. Flow over the flare transitioned from laminar to transitional/turbulent between 4 and 8 million per foot at 8 and 12 degrees angle of attack, and near 4 million per foot at 16 degrees angle of attack.

Greene, Francis A.↗

NASA NTRS2001

Measured and Computed Hypersonic Aerodynamic/Aeroheating Characteristics for an Elliptically Blunted Flared Cylinder

Computational and experimental hypersonic aerodynamic forces and moments and aeroheating levels for Kistler Aerospace Corporation's baseline orbiter vehicle at incidence are presented. Experimental data were measured in ground-based facilities at the Langley Research Center and predictions were performed using the Langley Aerothermodynamic Upwind Relaxation Algorithm code. The test parameters were incidence (-4 to 24 degrees), freestream Mach number (6 to 10), freestream ratio of specific heats (1.2 to 1.4), and freestream Reynolds number (0.5 to 8.0 million per foot). The effects of these parameters on aerodynamic characteristics, as well as the effects of Reynolds number on measured heating levels are discussed. Good agreement between computational and experimental aerodynamic and aeroheating values were observed over the wide range of test parameters examined. Reynolds number and ratio of specific heats were observed to significantly alter the trim L/D value. At Mach 6, laminar flow, was observed along the entire windward centerline up to the flare for all angles and Reynolds numbers tested. Flow over the flare transitioned front laminar to transitional turbulent between 4 and 8 million per foot at 8 and 12 degrees angle of attack, and near 4 million per foot at 16 degrees angle of attack.

Greene, Francis A.↗

NASA NTRS2016

Acoustic Radiation From a Mach 14 Turbulent Boundary Layer

Direct numerical simulations (DNS) are used to examine the turbulence statistics and the radiation field generated by a high-speed turbulent boundary layer with a nominal freestream Mach number of 14 and wall temperature of 0:18 times the recovery temperature. The flow conditions fall within the range of nozzle exit conditions of the Arnold Engineering Development Center (AEDC) Hypervelocity Tunnel No. 9 facility. The streamwise domain size is approximately 200 times the boundary-layer thickness at the inlet, with a useful range of Reynolds number corresponding to Re 450 􀀀 650. Consistent with previous studies of turbulent boundary layer at high Mach numbers, the weak compressibility hypothesis for turbulent boundary layers remains applicable under this flow condition and the computational results confirm the validity of both the van Driest transformation and Morkovin's scaling. The Reynolds analogy is valid at the surface; the RMS of fluctuations in the surface pressure, wall shear stress, and heat flux is 24%, 53%, and 67% of the surface mean, respectively. The magnitude and dominant frequency of pressure fluctuations are found to vary dramatically within the inner layer (z/delta 0.< or approx. 0.08 or z+ < or approx. 50). The peak of the pre-multiplied frequency spectrum of the pressure fluctuation is f(delta)/U(sub infinity) approx. 2.1 at the surface and shifts to a lower frequency of f(delta)/U(sub infinity) approx. 0.7 in the free stream where the pressure signal is predominantly acoustic. The dominant frequency of the pressure spectrum shows a significant dependence on the freestream Mach number both at the wall and in the free stream.

Zhang, Chao↗

NASA NTRS2004

Exhaust Simulation Testing of a Hypersonic Airbreathing Model at Transonic Speeds

An experimental study was performed to examine jet-effects for an airframe-integrated, scramjet-rocket combined-cycle vehicle configuration at transonic test conditions. This investigation was performed by testing an existing exhaust simulation wind tunnel model, known as Model 5B, in the NASA Langley 16-Ft. Transonic Tunnel. Tests were conducted at freestream Mach numbers from 0.7 to 1.2, at angles of attack from 2 to +14 degrees, and at up to seven nozzle static pressure ratio values for a set of horizontal-tail and body-flap deflections. The model aftbody, horizontal tails, and body flaps were extensively pressure instrumented to provide an understanding of jet-effects and control-surface/plume interactions, as well as for the development of analytical methodologies and calibration of computational fluid dynamic codes to predict this type of flow phenomenon. At all transonic test conditions examined, the exhaust flow at the exit of the internal nozzle was over-expanded, generating an exhaust plume that turned toward the aftbody. Pressure contour plots for the aftbody of Model 5B are presented for freestream transonic Mach numbers of 0.70, 0.95, and 1.20. These pressure data, along with shadowgraph images, indicated the impingement of an internal plume shock and at least one reflected shock onto the aftbody for all transonic conditions tested. These results also provided evidence of the highly three-dimensional nature of the aftbody exhaust flowfield. Parametric testing showed that angle-of-attack, static nozzle pressure ratio, and freestream Mach number all affected the exhaust-plume size, exhaust-flowfield shock structure, and the aftbody-pressure distribution, with Mach number having the largest effect. Integration of the aftbody pressure data showed large variations in the pitching moment throughout the transonic regime.

Huebner, Lawrence D.↗

NASA NTRS1994

Two-Dimensional Scramjet Inlet Unstart Model: Wind-Tunnel Blockage and Actuation Systems Test

This supplement to NASA TM 109152 shows the Schlieren video (10 min. 52 sec., color, Beta and VHS) of the external flow field and a portion of the internal flow field of a two-dimensional scramjet inlet model in the NASA Langley 20-Inch Mach 6 Tunnel. The intent of the overall test program is to study (both experimentally and computationally) the dynamics of the inlet unstart; this (phase I) effort examines potential wind-tunnel blockage issues related to model sizing and the adequacy of the actuation systems in accomplishing the start and unstart. The model is equipped with both a moveable cowl and aft plug. Windows in the inlet sidewalls allow limited optical access to the internal shock structure. In the video, flow is from right to left, and the inlet is oriented inverted with respect to flight, i.e., with the cowl on top. The plug motion is obvious because the plug is visible in the aft window. The cowl motion, however, is not as obvious because the cowl is hidden from view by the inlet sidewall. The end of the cowl actuator arm, however, becomes visible above the inlet sidewalls between the windows when the cowl is up (see figure 1b of the primary document). The model is injected into the tunnel and observed though several actuation sequences with two plug configurations over a range of unit freestream Reynolds number at a nominal freestream Mach number of 6. The framing rate and shutter speed of the camera were too slow to fully capture the dynamics of the unstart but did prove sufficient to identify inlet start and unstart. This series of tests indicated that the model was appropriately sized for this facility and identified operability limits required first to allow the inlet to start and second to force the unstart.

Holland, Scott D.↗

NASA NTRS1975

An experimental investigation of heat transfer to reusable surface insulation tile array gaps in a turbulent boundary layer with pressure gradient

An experimental investigation was performed to determine the effect of pressure gradient on the heat transfer to space shuttle reusable surface insulation (RSI) tile array gaps under thick, turbulent boundary layer conditions. Heat transfer and pressure measurements were obtained on a curved array of full-scale simulated RSI tiles in a tunnel wall boundary layer at a nominal freestream Mach number of 10.3 and freestream unit Reynolds numbers of 1.6, 3.3, and and 6.1 million per meter. Transverse pressure gradients were induced over the model surface by rotating the curved array with respect to the flow. Definition of the tunnel wall boundary layer flow was obtained by measurement of boundary layer pitot pressure profiles, and flat plate wall pressure and heat transfer. Flat plate wall heat transfer data were correlated and a method was derived for prediction of smooth, curved array heat transfer in the highly three-dimensional tunnel wall boundary layer flow and simulation of full-scale space shuttle vehicle pressure gradient levels was assessed.

Throckmorton, D. A.↗

NASA NTRS1991

Applications of hot-film anemometers in hypersonic shear layers

A wind tunnel test was conducted on a flat plate at zero angle of attack with a rearward facing 2D cooling film injector nozzle. The freestream Mach number was 8 and the injector Mach number was 3. The freestream Reynolds number varied from 0.43 to 3.3 million per ft during the test, and the injector flow rate was such that the jet exit and freestream static pressures were matched. The analysis reported herein will focus on data obtained at a freestream Reynolds number of 0.85 million per ft. The data consists of heat-transfer measurements obtained upstream and downstream of the injector nozzle and flowfield surveys obtained downstream of the injector nozzle with a pitot, total temperature, hot-film anemometer and hot-wire anemometer probes. The flowfield surveys were made at stations 0.1 to 9 in. downstream of the injector nozzle from near the model surface to approximately 2 in above the model surface. The hot-film anemometer was used to define the fluctuations in the shear layer separating the flows. The hot-film results are integrated with conventional measurement techniques to obtain a more complete description of the complicated shear layer separating hypersonic and supersonic flows.

Grubb, J. P.↗

NASA NTRS1993

Aerodynamics of powered missile separation from F/A-18 aircraft

A 3D dynamic 'chimera' algorithm that solves the thin-layer Navier-Stokes equations over multiple moving bodies was modified to numerically simulate the aerodynamics, missile dynamics, and missile plume interactions of a missile separating from a generic wing and from an F/A-18 aircraft in transonic flow. The missile is mounted below the wing for missile separation from the wing and on the F/A-18 fuselage at the engine inlet side for missile separation from aircraft. Static and powered missile separation cases are considered to examine the influence of the missile and plume on the wing and F/A-18 fuselage and engine inlet. The aircraft and missile are at two degrees angle of attack, Reynolds number of 10 million, freestream Mach number of 1.05 and plume Mach number of 3.0. The computational results show the details of the flow field.

Ahmad, J. U.↗