Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel Performance Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Cold flow testing of the Space Shuttle Main Engine alternate turbopump development high pressure fuel turbine model

NASA's Marshall Space Flight Center has established a cold airflow turbine test program to experimentally determine the performance of liquid rocket engine turbopump drive turbines. Testing of the SSME alternate turbopump development (ATD) fuel turbine was conducted for back-to-back comparisons with the baseline SSME fuel turbine results obtained in the first quarter of 1991. Turbine performance, Reynolds number effects, and turbine diagnostics, such as stage reactions and exit swirl angles, were investigated at the turbine design point and at off-design conditions. The test data showed that the ATD fuel turbine test article was approximately 1.4 percent higher in efficiency and flowed 5.3 percent more than the baseline fuel turbine test article. This paper describes the method and results used to validate the ATD fuel turbine aerodynamic design. The results are being used to determine the ATD high pressure fuel turbopump (HPFTP) turbine performance over its operating range, anchor the SSME ATD steady-state performance model, and validate various prediction and design analyses.

Gaddis, Stephen W.↗
NASA NTRS2023

Performance Modeling of Urban Air Mobility Vehicles to Support Air Traffic Management Research

The recent emergence of Urban Air Mobility (UAM) vehicles has resulted in a need for flight performance models that enable comprehensive simulation-based research on air traffic management topics such as route structure, scheduling, and separation standards. Successful performance modeling methods exist for a wide range of traditional aircraft designs. However, comparable modeling methods appropriate for UAM vehicles that combine fixed-wing and rotorcraft performance have not yet been established. One challenge to progress has been the lack of available data capturing the performance characteristics and unique flight profiles of these aircraft. This paper describes methods used to generate the required performance data and the development of performance models for UAM vehicles. Included is a review of the energy and power equations often used in developing performance models for traditional aircraft as well as a discussion of their applicability to UAM vehicles. The challenge of generating realistic performance data in over-actuated vehicles transitioning from hover to cruise flight is also addressed through an approach based on objective function optimization. A table-based performance model format adapted to UAM configurations is described, as well as parametric models intended to accompany the performance table to allow detailed modeling of power and fuel consumption during accelerated flight, turning flight, or flight at an arbitrary climb or descent rate. A discussion of future work is also provided, including the need for refinement of UAM performance modeling methods and formats, especially in conjunction with improvements to aerodynamic modeling of vehicles with complex designs where strong interaction effects may dominate important regions of the flight envelope.

Performance Modeling↗
NASA NTRS2023

Performance Modeling of Urban Air Mobility Vehicles to Support Air Traffic Management Research

The recent emergence of Urban Air Mobility (UAM) vehicles has resulted in a need for flight performance models that enable comprehensive simulation-based research on air traffic management topics such as route structure, scheduling, and separation standards. Successful performance modeling methods exist for a wide range of traditional aircraft designs. However, comparable modeling methods appropriate for UAM vehicles that combine fixed-wing and rotorcraft performance have not yet been established. One challenge to progress has been the lack of available data capturing the performance characteristics and unique flight profiles of these aircraft. This paper describes methods used to generate the required performance data and the development of performance models for UAM vehicles. Included is a review of the energy and power equations often used in developing performance models for traditional aircraft as well as a discussion of their applicability to UAM vehicles. The challenge of generating realistic performance data in over-actuated vehicles transitioning from hover to cruise flight is also addressed through an approach based on objective function optimization. A table-based performance model format adapted to UAM configurations is described, as well as parametric models intended to accompany the performance table to allow detailed modeling of power and fuel consumption during accelerated flight, turning flight, or flight at an arbitrary climb or descent rate. A discussion of future work is also provided, including the need for refinement of UAM performance modeling methods and formats, especially in conjunction with improvements to aerodynamic modeling of vehicles with complex designs where strong interaction effects may dominate important regions of the flight envelope.

Performance Modeling↗
NASA NTRS2007

High Fidelity, Fuel-Like Thermal Simulators for Non-Nuclear Testing: Analysis and Initial Test Results

Non-nuclear testing can be a valuable tool in the development of a space nuclear power system, providing system characterization data and allowing one to work through various fabrication, assembly and integration issues without the cost and time associated with a full ground nuclear test. In a non-nuclear test bed, electric heaters are used to simulate the heat from nuclear fuel. Testing with non-optimized heater elements allows one to assess thermal, heat transfer. and stress related attributes of a given system, but fails to demonstrate the dynamic response that would be present in an integrated, fueled reactor system. High fidelity thermal simulators that match both the static and the dynamic fuel pin performance that would be observed in an operating, fueled nuclear reactor can vastly increase the value of non-nuclear test results. With optimized simulators, the integration of thermal hydraulic hardware tests with simulated neutronic response provides a bridge between electrically heated testing and fueled nuclear testing. By implementing a neutronic response model to simulate the dynamic response that would be expected in a fueled reactor system, one can better understand system integration issues, characterize integrated system response times and response characteristics and assess potential design improvements at relatively small fiscal investment. Initial conceptual thermal simulator designs are determined by simple one-dimensional analysis at a single axial location and at steady state conditions; feasible concepts are then input into a detailed three-dimensional model for comparison to expected fuel pin performance. Static and dynamic fuel pin performance for a proposed reactor design is determined using SINDA/FLUINT thermal analysis software, and comparison is made between the expected nuclear performance and the performance of conceptual thermal simulator designs. Through a series of iterative analyses, a conceptual high fidelity design is developed: this is followed by engineering design, fabrication, and testing to validate the overall design process. Test results presented in this paper correspond to a "first cut" simulator design for a potential liquid metal (NaK) cooled reactor design that could be applied for Lunar surface power. Proposed refinements to this simulator design are also presented.

Bragg-Sitton, Shannon M.↗
NASA NTRS1953

Free-flight Performance of a Rocket-boosted, Air-launched 16-inch-diameter Ram-jet Engine at Mach Numbers up to 2.20

The investigation of air-launched ram-jet engines has been extended to include a study of models with a nominal design free-stream Mach number of 2.40. These models require auxiliary thrust in order to attain a flight speed at which the ram jet becomes self-accelerating. A rocket-boosting technique for providing this auxiliary thrust is described and time histories of two rocket-boosted ram-jet flights are presented. In one flight, the model attained a maximum Mach number of 2.20 before a fuel system failure resulted in the destruction of the engine. Performance data for this model are presented in terms of thrust and drag coefficients, diffuser pressure recovery, mass-flow ratio, combustion efficiency, specific fuel consumption, and over-all engine efficiency.

AIR INLETS - NOSE, ANNULAR↗
NASA NTRS2010

Preliminary Characterizations of Altair Lunar Lander Slosh Dynamics and Some Implications for TVC Design

During thrust maneuvers, the sloshing of fuel in partially filled tanks could interact with the controlled system in such a way as to cause the overall system to be unstable. This failure mode could be a result of poor coordination between systems engineers of Structures, Propulsion, GN&C, Mission Operations, and other subsystems. Attentions to the following is a minimum: Placements of fuel tanks, Tank shapes and baffle designs, Separation of TVC BW from slosh mode frequencies, Adequacy of excursion range of engine gimbal actuators in all engine burns, BW of sensors (e.g., gyroscopes) and actuators (e.g., engine gimbal), Structural frequencies of spacecraft and engine mounts, Prediction of S/C's c.m. location, canting of gimbal null axis, others. Check overall TVC performance via validated simulation test bed. Modeling fuel slosh during spacecraft thrusting maneuvers • Placement of fuel tanks to guarantee stable interactions between fuel slosh mode and the S/C rigid-body mode • Estimation of slosh frequencies (as a function of mission phases): – Estimation of slosh mode damping • Some implications for Thrust Vector Control design: – Selection of TVC controller bandwidth – Adequacy of the excursion range of engine gimbal actuator • TVC system design: Complex Interactions between GN&C, Propulsion, Structure, and Other Subsystems

Thrust vector control↗
NASA NTRS2020

Optimizing Performance and Accuracy with LIFQWIK

For the 2020 Summer Internship period, optimization and analysis was performed of a new iteration of the LIFQWIK PLIF model, used to evaluate the accuracy of CFD simulations of fuel injector performance. This presentation details the accuracy and performance optimization steps taken and presents the results of that optimization.

CFD↗
NASA NTRS1998

Aviation Fuel Tracer Simulation: Model Intercomparison and Implications

An upper limit for aircraft-produced perturbations to aerosols and gaseous exhaust products in the upper troposphere and lower stratosphere (UT/LS) is derived using the 1992 aviation fuel tracer simulation performed by eleven global atmospheric models. Key Endings are that subsonic aircraft emissions: (1) have not be responsible for the observed water vapor trends at 40 deg N; (2) could be a significant source of soot mass near 12 km, but not at 20 km; (3) might cause a noticeable increase in the background sulfate aerosol surface area and number densities (but not mass density) near the northern mid-latitude tropopause; and (4) could provide a global, annual mean top of the atmosphere radiative forcing up to +0.006 W/sq m and -0.013 W/sq m due to emitted soot and sulfur, respectively.

Danilin, M. Y.↗
NASA NTRS1998

Aviation Fuel Tracer Simulation: Model Intercomparison and Implications

An upper limit for aircraft-produced perturbations to aerosols and gaseous exhaust products in the upper troposphere and lower stratosphere (UT/LS) is derived using the 1992 aviation fuel tracer simulation performed by eleven global atmospheric models. Key findings are that subsonic aircraft emissions: (1) have not been responsible for the observed water vapor trends at 40degN; (2) could be a significant source of soot mass near 12 km, but not at 20 km; (3) might cause a noticeable increase in the background sulfate aerosol surface area and number densities (but not mass density) near the northern mid-latitude tropopause; and (4) could provide a global, annual mean top of the atmosphere radiative forcing up to +0.006 W/sq m and -0.013 W/sq m due to emitted soot and sulfur, respectively.

Danilin, M. Y.↗
NASA NTRS1981

Effect of fuel injector type on performance and emissions of reverse-flow combustor

The combustion process in a reverse-flow combustor suitable for a small gas turbine engine was investigated to evaluate the effect of fuel injector type on performance and emissions. Fuel injector configurations using pressure-atomizing, spill-flow, air blast, and air-assist techniques were compared and evaluated on the basis of performance obtained in a full-scale experimental combustor operated at inlet conditions corresponding to takeoff, cruise, low power, and idle and typical of a 16:1-pressure-ratio turbine engine. Major differences in combustor performance and emissions characteristics were experienced with each injector type even though the aerodynamic configuration was common to most combustor models. Performance characteristics obtained with the various fuel injector types could not have been predicted from bench-test injector spray characteristics. The effect of the number of operating fuel injectors on performance and emissions is also presented.

Norgren, C. T.↗
NASA NTRS2007

High Fidelity Thermal Simulators for Non-Nuclear Testing: Analysis and Initial Results

Non-nuclear testing can be a valuable tool in the development of a space nuclear power system, providing system characterization data and allowing one to work through various fabrication, assembly and integration issues without the cost and time associated with a full ground nuclear test. In a non-nuclear test bed, electric heaters are used to simulate the heat from nuclear fuel. Testing with non-optimized heater elements allows one to assess thermal, heat transfer, and stress related attributes of a given system, but fails to demonstrate the dynamic response that would be present in an integrated, fueled reactor system. High fidelity thermal simulators that match both the static and the dynamic fuel pin performance that would be observed in an operating, fueled nuclear reactor can vastly increase the value of non-nuclear test results. With optimized simulators, the integration of thermal hydraulic hardware tests with simulated neutronie response provides a bridge between electrically heated testing and fueled nuclear testing, providing a better assessment of system integration issues, characterization of integrated system response times and response characteristics, and assessment of potential design improvements' at a relatively small fiscal investment. Initial conceptual thermal simulator designs are determined by simple one-dimensional analysis at a single axial location and at steady state conditions; feasible concepts are then input into a detailed three-dimensional model for comparison to expected fuel pin performance. Static and dynamic fuel pin performance for a proposed reactor design is determined using SINDA/FLUINT thermal analysis software, and comparison is made between the expected nuclear performance and the performance of conceptual thermal simulator designs. Through a series of iterative analyses, a conceptual high fidelity design can developed. Test results presented in this paper correspond to a "first cut" simulator design for a potential liquid metal (NaK) cooled reactor design that could be applied for Lunar surface power. Proposed refinements to this simulator design are also presented.

Bragg-Sitton, Shannon M.↗
NASA NTRS1991

Evaluation of on-board hydrogen storage methods f or high-speed aircraft

Hydrogen is the fuel of choice for hypersonic vehicles. Its main disadvantage is its low liquid and solid density. This increases the vehicle volume and hence the drag losses during atmospheric flight. In addition, the dry mass of the vehicle is larger due to larger vehicle structure and fuel tankage. Therefore it is very desirable to find a fuel system with smaller fuel storage requirements without deteriorating the vehicle performance substantially. To evaluate various candidate fuel systems, they were first screened thermodynamically with respect to their energy content and cooling capacities. To evaluate the vehicle performance with different fuel systems, a simple computer model is developed to compute the vehicle parameters such as the vehicle volume, dry mass, effective specific impulse, and payload capacity. The results indicate that if the payload capacity (or the gross lift-off mass) is the most important criterion, only slush hydrogen and liquid hydrogen - liquid methane gel shows better performance than the liquid hydrogen vehicle. If all the advantages of a smaller vehicle are considered and a more accurate mass analysis can be performed, other systems using endothermic fuels such as cyclohexane, and some boranes may prove to be worthy of further consideration.

Akyurtlu, Ates↗
NASA NTRS1987

Self-regulating heater application to Shuttle/Centaur hydrazine fuel line thermal control

The Shuttle/Centaur high energy upper stage vehicle thermal environments were more severe than previous Centaur vehicle thermal environments, creating need for a new hydrazine fuel line thermal control technique. Constant power heaters did not satisfy power dissipation requirements, because the power required to maintain fuel line thermal control during cold conditions exceeded the maximum power allowable during hot conditions. Therefore, a Raychem Thermolimit self-regulating heater was selected for this application, and was attached to the hydrazine fuel line with Kapton and aluminum foil tapes. Fuel line/heater thermal modeling and subsequent thermal vacuum chamber testing simulated heater thermal performance during all worst-case Shuttle/Centaur thermal environmental conditions. Fuel line temperatures were maintained between the 4C to 71C limits during all analytical and test cases. Finally, the thermal model predictions were correlated with the test data, thereby ensuring that the model would provide satisfactory predictions for future missions and/or vehicles.

Unkrich, David B.↗
NASA NTRS1992

Mathematical Modeling Of A Nuclear/Thermionic Power Source

Report discusses mathematical modeling to predict performance and lifetime of spacecraft power source that is integrated combination of nuclear-fission reactor and thermionic converters. Details of nuclear reaction, thermal conditions in core, and thermionic performance combined with model of swelling of fuel.

Vandersande, Jan W.↗
NASA NTRS2018

Fuel Cell Model Validation with Power Module Test Data

The AES Modular Power Systems (AMPS) Fuel Cell team at the NASA Glenn Research Center (GRC) has created a Microsoft Excel model of a regenerative fuel cell (RFC) system for potential lunar and Martian applications. Due to some limitations of this model, including the ability to predict transient effects in the thermal and fluidic performance of the system, a system-level transient thermal/fluids model was desired. GT-SUITE is a transient multi-physics simulation tool that is popular in the automotive industry and has a built-in template for proton exchange membrane (PEM) fuel cells. However, terrestrial fuel cells used in the automotive industry vary significantly from aerospace fuel cells. A validation effort was undertaken to compare GT SUITE model results to actual data collected during the 2015 AMPS (Advanced Exploration Systems (AES) Modular Power Systems) Power Module Demonstration in which the AMPS team used a PEM fuel cell system to power a 478 kilogram rover assembly at the Dunes test site located at GRC. The purpose of the model was to evaluate the efficacy of using GT SUITE to model a non-flow through PEM fuel cell system. The validation effort examined electrochemical performance including fuel cell stack voltage and power supplied, the thermal performance of the stack namely stack temperature and heat rejection rates, and the fluidic performance of the system including pressures, reactant consumption, and water production rates.

Model Validation↗
NASA NTRS1991

Flow visualization and computational studies of a reverse flow circular combustor

The development of a reverse-flow circular combustor is described in terms of the visualization techniques that are employed to optimize the flow and mixing of fuel and air. The Fluent computer program is used in conjunction with flow visualization studies to investigate the performance of the combustor. The combustor has multiple mini-combustion zones (MCZs) and fuel injection nozzles along its circular geometry, and the fuel injection design is modeled to determine temperature distribution, including the performance at the combustor exit. The yellow dye smoke used in the visualization demonstrated desirable flow patterns with rapid circulation patterns within the MCZs and extensive interaction between the channel flow and the MCZs. The results are similar to those of CFD models, and the main conclusions are that fuel atomization can be further optimized and that the fuel injector nozzle can control swirls, fuel spray angle, and jet penetration.

Ghorashi, B.↗
NASA NTRS1981

Simplified off-design performance model of a day turbofan engine cycle

The specific thrust and fuel-air ratio for a dry turbofan engine cycle were calculated for several power levels over a range of altitudes and Mach numbers. The engine has a design fan pressure ratio of 2.9, compressor pressure ratio of 8.0, and bypass ratio of 0.6. Nominal engine component curves were picked to approximate the calculated data to construct a simplified model of the off-design performance of the engine. The model was then used to construct a simplified design-point engine model for the full-power condition.

Lallman, F. J.↗