Search NASA⌕ Search

SEARCH · Search NASA

Results for “GASOLINE COMPRESSION ENGINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Electric and hybrid vehicle environmental control subsystem study

An environmental control subsystem (ECS) in electric and hybrid vehicles is studied. A combination of a combustion heater and gasoline engine (Otto cycle) driven vapor compression air conditioner is selected. The combustion heater, the small gasoline engine, and the vapor compression air conditioner are commercially available. These technologies have good cost and performance characteristics. The cost for this ECS is relatively close to the cost of current ECS's. Its effect on the vehicle's propulsion battery is minimal and the ECS size and weight do not have significant impact on the vehicle's range.

Heitner, K. L.↗
DOE OSTI2020

Numerical study of advanced compression ignition and combustion in a gasoline direct injection engine

Multi-mode combustion strategies may provide a considerable thermal efficiency improvement targeted at part-load operating conditions for light-duty spark-ignition (SI) engines. The extension from boosted SI mode at high loads to advanced compression ignition (ACI) mode at low loads can be achieved by increasing compression ratio and utilizing intake air heating. In order to enable an accurate control of intake charge condition for ACI control and rapid mode-switches, it is essential to gain fundamental insight into the autoignition process with regard to thermal and fuel-air mixture stratification in the combustion chamber. In this work, a computational fluid dynamics (CFD) study is carried out to reveal some degrees of correlation between the mixture and thermal stratifications induced by the cylinder wall temperature and combustion-phasing across varying engine load conditions. The computational analysis begins with a calibrated simulation setup best matching the engine experiments, and subsequently evaluates the baseline setup for an extended range of engine load conditions for two excess-air ratio cases. The present study emphasizes the dominance of thermal stratifications for autoignition process due to wall temperature effects depending on the engine load conditions of interest. In addition, this study also aims to provide insight into the impact of mixture stratification on cyclic variability, especially at colder wall engine conditions (e.g., cold start). Observations herein provide highlight of the propensity of autoignition in correlation with mixture reactivity space.

Advanced Compression Ignition (ACI) engine↗
DOE OSTI2020

Engine Combustion System Optimization Using Computational Fluid Dynamics and Machine Learning: A Methodological Approach

Gasoline compression ignition (GCI) engines are considered an attractive alternative to traditional spark-ignition and diesel engines. Here, a Machine Learning-Grid Gradient Ascent (ML-GGA) approach was developed to optimize the performance of internal combustion engines. ML offers a pathway to transform complex physical processes that occur in a combustion engine into compact informational processes. The developed ML-GGA model was compared with a recently developed Machine Learning-Genetic Algorithm (ML-GA). Detailed investigations of optimization solver parameters and variable limit extension were performed in the present ML-GGA model to improve the accuracy and robustness of the optimization process. Detailed descriptions of the different procedures, optimization tools, and criteria that must be followed for a successful output are provided here. The developed ML-GGA approach was used to optimize the operating conditions (case 1) and the piston bowl design (case 2) of a heavy-duty diesel engine running on a gasoline fuel with a research octane number (RON) of 80. The ML-GGA approach yielded >2% improvements in the merit function, compared with the optimum obtained from a thorough computational fluid dynamics (CFD) guided system optimization. The predictions from the ML-GGA approach were validated with engine CFD simulations. This study demonstrates the potential of ML-GGA to significantly reduce the time needed for optimization problems, without loss in accuracy compared with traditional approaches.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Computational study on the impact of gasoline-ethanol blending on autoignition and soot/NO x emissions under low-load gasoline compression ignition conditions

Here, in the present work, computational fluid dynamics (CFD) simulations of a single-cylinder gasoline compression ignition (GCI) engine are performed to investigate the impact of gasoline-ethanol blending on autoignition, nitrogen oxide (NO x ), and soot emissions under low-load conditions. In order to represent the test gasoline (RD5-87), a four-component toluene primary reference fuel (TPRF)+ethanol (ETPRF) surrogate (with 10% ethanol by volume; E10) is employed. A three-dimensional (3D) engine CFD model employing finite-rate chemistry with a skeletal kinetic mechanism (including NO x sub-mechanism), adaptive mesh refinement (AMR), and hybrid method of moments (HMOM) is adopted to capture the in-cylinder combustion phenomena and soot/NO x emissions. The engine CFD model is validated against experimental data for three gasoline-ethanol blends: E10, E30 and E100, with varying ethanol content by volume. Model validation is carried out for a broad range of start-of-injection (SOI) timings (−21, −27, −36, and −45 crank angle degrees (°CA) after top-dead-center (aTDC)) with respect to in-cylinder pressure, heat release rate, combustion phasing, NO x and soot emissions. For relatively later injection timings (−21 and −27 °CA aTDC), E30 yields higher amount of soot than E10; while the trend reverses for early injection cases (−36 and −45 °CA aTDC ). On the other hand, E100 yields the lowest amount of soot among all fuels irrespective of SOI timing. Further, E10 shows a non-monotonic trend in soot emissions with SOI timing: SOI-36>SOI-45>SOI-21>SOI-27, while soot emissions from E30 exhibit monotonic decrease with advancing SOI timing. NO x emissions from various fuels follow a trend of E10>E30>E100. On the other hand, NO x emissions increase as SOI timing is advanced for all fuels, with an anomaly for E10 and E100 where NO x decreases when SOI is advanced beyond −36 °CA aTDC. Detailed analysis of the numerical results is performed to investigate the soot/NO x emission trends and elucidate the impact of chemical composition and physical properties on autoignition and emissions characteristics.

Computational fluid dynamics↗
DOE OSTI2022

The impact of fuel and injection strategy on combustion characteristics, emissions and efficiency in gasoline compression ignition operation

Gasoline compression ignition in diesel engines has been proposed in order to meet increasingly stringent emission regulations without sacrificing efficiency. In this study, a six-cylinder heavy-duty diesel engine was operated in a mixing controlled gasoline compression ignition mode to investigate the influence of fuels and injection strategies on the combustion characteristics, emissions, and thermal efficiencies. Fuels, including ethanol (E), isobutanol (IB), and diisobutylene (DIB), were blended with a gasoline fuel to form E10, E30, IB30, and DIB30 based on volumetric fraction. These four blends along with gasoline formed the five test fuels. With these fuels, three injections strategies were investigated, including late pilot injection, early pilot injection, and port fuel injection/direct injection. The impact of moderate exhaust gas recirculation on nitrogen oxides and soot emissions was examined to determine the most promising fuel/injection strategy for emissions reduction. In addition, first and second law analyses were performed to provide insights into the efficiency, loss, and exergy destruction of the various gasoline fuel blends at low and medium load conditions. Overall, the emission output, thermal efficiency, and combustion performances of the five fuels were found to be similar and their differences are modest under most test conditions. E30 with the port/direct fuel injection strategy obtained the peak brake thermal efficiency (46.9%) and gross indicated thermal efficiency (52.2%) at 14 bar. At 7 bar, the peak brake thermal efficiency (44.2%) and gross indicated thermal efficiency (52.5%) also belonged to E30 with the late pilot injection strategy. The second law analysis revealed that exergy destruction was mostly influenced by the fuel type and not by the injection strategy for the 14 bar operating conditions. However, the opposite trend was observed for the 7 bar case. In addition, port fuel injection in combination with oxygenated fuel blends was found to be helpful to suppress soot emissions for operation with exhaust gas recirculation.

co-optima fuels↗
DOE OSTI2016

Effects of injection parameters, boost, and swirl ratio on gasoline compression ignition operation at idle and low-load conditions

In this study, we study the effects of injector nozzle inclusion angle, injection pressure, boost, and swirl ratio on gasoline compression ignition combustion. Closed-cycle computational fluid dynamics simulations using a 1/7th sector mesh representing a single cylinder of a four-cylinder 1.9 L diesel engine, operated in gasoline compression ignition mode with 87 anti-knock index (AKI) gasoline, were performed. Two different operating conditions were studied—the first is representative of idle operation (4 mg fuel/cylinder/cycle, 850 r/min), and the second is representative of a low-load condition (10 mg fuel/cylinder/cycle, 1500 r/min). The mixture preparation and reaction space from the simulations were analyzed to gain insights into the effects of injection pressure, nozzle inclusion angle, boost, and swirl ratio on achieving stable low-load to idle gasoline compression ignition operation. It was found that narrower nozzle inclusion angles allow for more reactivity or propensity to ignition (determined qualitatively by computing constant volume ignition delays) and are suitable over a wider range of injection timings. Under idle conditions, it was found that lower injection pressures helped to reduce overmixing of the fuel, resulting in greater reactivity and ignitability (ease with which ignition can be achieved) of the gasoline. However, under the low-load condition, lower injection pressures did not increase ignitability, and it is hypothesized that this is because of reduced chemical residence time resulting from longer injection durations. Reduced swirl was found to maintain higher in-cylinder temperatures through compression, resulting in better ignitability. It was found that boosting the charge also helped to increase reactivity and advanced ignition timing.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Numerical analysis of soot emissions from gasoline-ethanol and gasoline-butanol blends under gasoline compression ignition conditions

In the present work, computational fluid dynamics (CFD) simulations of a single-cylinder gasoline compression ignition (GCI) engine were performed to investigate the impact of blending two biofuels, ethanol and n-butanol, with gasoline on the trade-off between combustion phasing and soot emissions under low load conditions. Here, in order to represent market gasoline (RD5-87), a four-component toluene primary reference fuel (TPRF) + ethanol (ETPRF) surrogate (with 20% ethanol by mole; E20) was formulated using a neural network based octane predictor such that the surrogate had the same ethanol content, Research Octane Number (RON) and Octane Sensitivity (S). In addition, a novel skeletal kinetic mechanism for ETPRF and TPRF + n-butanol (BTPRF) blends, incorporating polycyclic aromatic hydrocarbon (PAH) chemistry, was developed. A three-dimensional (3D) engine CFD formulation employing the skeletal mechanism, adaptive mesh refinement (AMR), finite-rate chemistry approach, and hybrid method of moments (HMOM) was adopted to capture the in-cylinder combustion phenomena and soot emissions. The engine CFD model was validated against RD5-87 experimental data for a broad range of start-of-injection (SOI) timings (-21/-27/-36/-45 crank angle degrees (CAD) after top-dead center (aTDC)), with respect to in-cylinder pressure, heat release rate, combustion phasing, and soot emissions. The closed-cycle simulation results were analyzed to elucidate the non-monotonic trend of soot emissions versus SOI timing: SOI-36 > SOI-45 > SOI-21 > SOI-27. Thereafter, the validated CFD model was employed to simulate the combustion of a gasoline-ethanol blend with 45% (by mole) ethanol (E45) and a gasoline-butanol blend with 45% (by mole) n-butanol (B45) under the same operating conditions to study the effects of fuel composition and SOI timing on combustion phasing and soot emissions. The sooting propensity followed the trend: B45 > E20 > E45 at all SOI timings. Overall, it was observed that the autoignition propensity was primarily related to fuel chemistry. On the other hand, sooting propensity showed strong coupling with both fuel chemistry and physical properties, with greater impact of fuel physical properties at advanced SOI timings.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Combustion, criteria pollutant and soot property assessment of mixing-controlled high-load engine operation with gasoline and diesel

Gasoline compression ignition (GCI) is an emerging technology that can achieve high fuel efficiency and low criteria emissions in diesel engine platforms using gasoline and gasoline-like fuels. While low- and mid-range loads are enabled with low temperature combustion (LTC) approaches, high-loads are more efficient with high temperature combustion (HTC) requiring mixing-controlled combustion (MCC). Lower soot emissions are achieved with gasoline even in high-load MCC than with diesel, but detailed soot properties from gasoline and diesel have been rarely discussed. In order to better understand how high-load operations affect soot properties, in this study gasoline and diesel were tested in a six-cylinder heavy duty engine at 14 bar brake mean effective pressure (BMEP) at similar combustion phasing. Effects of pilot mass ratio and EGR on heat release rates, cylinder temperatures, ignition delay (ID) and combustion duration (CD) were examined, relating with emissions variations with applications of the two fuels. Soot mass and particle number emissions were slightly lower with gasoline than with diesel, resulting in a more favorable NOx-soot trade-off with gasoline like other reports. Contrary to other findings in the literature, gasoline and diesel soot samples presented similar particle distribution shapes, carbon crystalline structures and primary particle sizes, regardless of fuel type and EGR rate. Consequently, the current result proposes that soot particles have undergone similar soot formation and oxidation processes despite reactivity difference and oxygen availability under the examined high-load MCC with similar combustion phases.

02 PETROLEUM↗
DOE OSTI2019

CFD-Guided Combustion System Optimization of a Gasoline Range Fuel in a Heavy-Duty Compression Ignition Engine Using Automatic Piston Geometry Generation and a Supercomputer

A computational fluid dynamics (CFD) guided combustion system optimization was conducted for a heavy-duty diesel engine running with a gasoline fuel that has a research octane number (RON) of 80. The goal was to optimize the gasoline compression ignition (GCI) combustion recipe (piston bowl geometry, injector spray pattern, in-cylinder swirl motion, and thermal boundary conditions) for improved fuel efficiency while maintaining engine-out NO x within a 1-1.5 g/kW-hr window. The numerical model was developed using the multi-dimensional CFD software CONVERGE. A two-stage design of experiments (DoE) approach was employed with the first stage focusing on the piston bowl shape optimization and the second addressing refinement of the combustion recipe. For optimizing the piston bowl geometry, a software tool, CAESES, was utilized to automatically perturb key bowl design parameters. This led to the generation of 256 combustion chamber designs evaluated at several engine operating conditions. The second DoE campaign was conducted to optimize injector spray patterns, fuel injection strategies and in-cylinder swirl motion for the best performing piston bowl designs from the first DoE campaign. This comprehensive optimization study was performed on a supercomputer, Mira, to accelerate the development of an optimized fuel-efficiency focused design. Compared to the production combustion system in the baseline engine, the new combustion recipe from this study showed significantly improved closed-cycle fuel efficiency across key engine operating points while meeting the engine-out NO x targets. Optimized piston bowl designs and injector spray patterns were predicted to provide enhanced in-cylinder air utilization and more rapid mixing-controlled combustion, thereby leading to a fuel efficiency improvement. In addition, shifting the engine thermal boundary conditions toward leaner operation was also key to the improved fuel efficiency.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Enhancing the efficiency benefit of thermal barrier coatings for homogeneous charge compression ignition engines through application of a low-k oxide

Prior experiments reported by the authors have proven the hypothesis that achieving a dynamic temperature swing on the combustion chamber surface will lead to improved thermal and combustion efficiencies of the homogeneous charge compression ignition engine. A thin layer of yttria-stabilized zirconia, roughly 150 μm, was plasma sprayed on the piston top. It led to markedly advanced ignition and heat release in the gasoline homogeneous charge compression ignition engine, accompanied with reduced unburnt hydrocarbon and carbon monoxide emissions, improved combustion efficiency, and a higher thermal efficiency. A related computational study highlighted the critical role of coating thermal conductivity in achieving a desired dynamic response; hence, the second phase of experimental investigations focused on introducing structured porosity in the yttria-stabilized zirconia coating, as a means of reducing effective conductivity. Indeed, additional incremental improvements were observed, as well as limitations related to adverse effects of the surface roughness and the fuel interactions with the surface roughness and open pores. Erosion can also be a problem in a direct injection engine. Therefore, the third round of investigations focused on a material with a natively low conductivity (low-k), sprayed on the top of an Al piston in a relatively dense form, and in a way that yields a smooth surface. The objective was to capitalize on the low conductivity, while avoiding the pitfalls accompanying high-porosity formulations. The heat-storage capacity was limited by keeping the thickness relatively low. The results verify the paramount importance of thermal conductivity in the context of high “temperature swing” behavior and indicate a potential to improve the homogeneous charge compression ignition engine’s combustion efficiency roughly 1.5%, with the overall indicated efficiency improvement on the order of 5%, on a relative basis. In addition, the low-k oxide thermal barrier applied to the piston extended significantly the low-load homogeneous charge compression ignition operability limit.

42 ENGINEERING↗
DOE OSTI2023

High Speed Data Acquisition for Real Time Feedback in a Light Duty Engine Combustion-Mode Switching Application

The paper describes the integration of a high-speed data acquisition and diagnostics controller used in an advanced engine platform. The controller enables ultra-low emissions and new benchmarks of engine efficiency while running a Gasoline Compression Ignition (GCI) cycle on a 2.2L, 4-cylinder engine. The system enables real-time combustion feedback and vibration analysis in engines. The paper focuses on: (1) the development of an interpolative sampling algorithm for transposition of time acquired data to the crank angle domain using a production crank sensor (60-2 tooth wheel); (2) the control unit, high-speed data acquisition, communication rates between the dedicated data acquisition and base controller to ensure cycle-to-cycle feedback; and, (3) validation exercises using cylinder pressure measurements. Here, the study shows how the algorithm resolves cylinder pressure information over an engine cycle, validating its robustness across acquisition rates of 50 and 200 kHz, with crank angle resolutions of 0.5° and 0.1°. Results show that the 50 kHz, 0.5° hardware yield combustion phasing and torque estimates within 0.1° and 1% torque of those attained with the 200 kHz, 0.1° hardware. Finally, study shows the dedicated controller and communication speeds allow for next-cycle fuel injection correction for speeds above 5000 rpm.

42 ENGINEERING↗
DOE OSTI2015

Characterization of Reactivity Controlled Compression Ignition (RCCI) Using Premixed Gasoline and Direct-Injected Gasoline with a Cetane Improver on a Multi-Cylinder Engine

The focus of the present paper was to characterize Reactivity Controlled Compression Ignition (RCCI) using a single-fuel approach of gasoline and gasoline mixed with a commercially available cetane improver on a multi-cylinder engine. RCCI was achieved by port-injecting a certification grade 96 research octane gasoline and direct-injecting the same gasoline mixed with various levels of a cetane improver, 2-ethylhexyl nitrate (EHN). The EHN volume percentages investigated in the direct-injected fuel were 10, 5, and 2.5%. The combustion phasing controllability and emissions of the different fueling combinations were characterized at 2300 rpm and 4.2 bar brake mean effective pressure over a variety of parametric investigations including direct injection timing, premixed gasoline percentage, and intake temperature. Comparisons were made to gasoline/diesel RCCI operation on the same engine platform at nominally the same operating condition. The experiments were conducted on a modern four cylinder light-duty diesel engine that was modified with a port-fuel injection system while maintaining the stock direct injection fuel system. The pistons were modified for highly premixed operation and feature an open shallow bowl design. The results indicate that the authority to control the combustion phasing through the fuel delivery strategy (e.g., direct injection timing or premixed gasoline percentage) is not a strong function of the EHN concentration in the direct-injected fuel. It was also observed that NOx emissions are a strong function of the global EHN concentration in-cylinder and the combustion phasing. Finally, in general, NOx emissions are significantly elevated for gasoline/gasoline+EHN operation compared with gasoline/diesel RCCI operation at a given operating condition.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Thermodynamic analysis of heat transfer reduction in spark ignition using thermal barrier coatings

This work uses a 0D thermodynamic engine model coupled to a 1D surface temperature solver to study the potential of low thermal inertia thermal barrier coatings (TBCs) on combustion chamber surfaces to increase the efficiency of spark ignition engines. Under ideal conditions, coating the piston crown, head, and valve faces with a TBC with a thermal inertia of 640 J/m 2 K s 1/2 resulted in less than a 1% relative improvement in efficiency. Despite using a low thermal inertia coating to avoid open cycle charge heating, the reduction in closed cycle heat transfer, which is the pathway to increasing efficiency, increased knock propensity. Therefore, any efficiency gain through closed cycle heat transfer reduction in spark ignition is offset by the need to retard spark timing to counter knock. An exergy analysis of completely blocking heat transfer for a 10 crank-angle degree window showed that on a low compression engine, like those used for stoichiometric gasoline spark ignition, the maximum efficiency gain achievable was limited compared to a higher compression ratio engine. Furthermore, the high gas temperatures of stoichiometric operation mean that even state-of-the-art TBCs cannot elevate surface temperatures enough purely through temperature swing to achieve a significant reduction in heat transfer near top dead center, where work availability is highest. Overall, these results indicate that low thermal inertia TBCs are ill-suited for achieving an efficiency benefit in spark ignition through a heat transfer reduction pathway. Instead spark ignition TBC research should explore ways to use low thermal inertia TBCs to achieve open cycle charge cooling to reduce knock propensity.

Engineering↗
DOE OSTI2019

Experimental investigation of the relationship between thermal barrier coating structured porosity and homogeneous charge compression ignition engine combustion

Heat transfer has a monumental influence on homogeneous charge compression ignition combustion. When a thermal barrier coating is applied to the combustion chamber, the insulating effect magnifies the wall temperature swing, decreasing heat transfer during combustion. This enables improvements in both thermal and combustion efficiency without the detrimental impacts of intake charge heating. Increasing the temperature swing requires coatings with lower thermal conductivity and heat capacity. An enticing avenue for simultaneously decreasing both thermal conductivity and capacity is to increase the porosity fraction. A proprietary solution precursor plasma spray process enables discrete organization of the porosity structure, called inter-pass boundaries, which in turn produces a step-reduction in thermal conductivity for a given porosity level. In this investigation, yttria-stabilized zirconia is used to create four different thermal barrier coatings to study the potential of structured porosity as means of improving the “temperature swing” behavior in a homogeneous charge compression ignition engine. The baseline coating is “dense YSZ,” applied using a standard air-plasma spray process. Furthermore, significant reductions of the thermal conductivity are achieved by utilizing the solution precursor plasma spray process to create inter-pass boundaries with a moderate overall porosity. Performance, efficiency, and emissions are compared against both a baseline configuration with a metal piston and an air-plasma spray “dense YSZ” coating. Experiments are carried out in a single-cylinder gasoline homogeneous charge compression ignition engine with exhaust re-induction. Experiments indicate that incorporating structured porosity into thermal barrier coatings produces tangible gains in combustion and thermal efficiencies. However, there is an upper limit to porosity levels acceptable for homogeneous charge compression ignition engine application because an elevated porosity fraction leads to excessive surface roughness and undesirable fuel interactions. Comparison of the coatings showed the best results with coating thickness of up to 150 µm. Thicker coatings led to slower surface temperature response and attenuated swing temperature magnitude.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Alkyl dialkoxyalkanoates as bioderived, high cetane diesel fuels

A fuel for an internal combustion engine includes a C 5 to C 30 dialkoxyalkanoate corresponding to formula (I), wherein the R 1 group is —H or a —CH 3 group, the R 2 and R 2 ′ groups are alkyl groups independently selected to have 1 to 9 carbon atoms; and the R 3 group is selected to have 1 to 9 carbon atoms. The compounds described herein may be used as neat fuels or mixed fuels (with diesel, biodiesel, jet fuel, marine fuel or other fuel compounds) in autoignition or spark ignition engines, such as diesel engines, gasoline (spark ignition) engines, MCCI, Homogeneous Charge Compression Ignition (HCCI) engines, or more generally in Low-Temperature Gasoline Combustion (LTGC) engines (using gasoline-like fuels), that have the high-efficiency advantages of HCCI but can operate with some level of charge inhomogeneities. Methods of making these compounds are environmentally friendly and can be done in a continuous manner.

Myllenbeck, Nicholas↗
DOE OSTI2021

Performance of direct injected propane and gasoline in a high stroke-to-bore ratio SI engine: Pathways to diesel efficiency parity with ultra low soot

This work explores pathways to achieve diesel-like, high-efficiency combustion with stoichiometric 3-way catalyst compatible combustion in a single-cylinder spark ignition (SI) research engine. A unique high stroke-to-bore engine design (1.5:1) with cooled exhaust gas recirculation (EGR) and high compression ratio ( r c ) was used to improve engine efficiency by up to 30% compared with a production turbocharged gasoline direct injection spark ignition engine. Engine experiments were conducted with both 91 RON E10 gasoline and liquified petroleum gas (LPG) (i.e. autogas) and were compared to legacy gasoline data on the production engine. Geometric compression ratio ( r c ) of 13.3:1 was used for both fuels with additional experiments at 16.8:1 for LPG only. Measurements of exhaust soot particle size and number concentrations were made with both fuels. Significant reduction in soot particles across the whole particle size range were achieved with LPG due to the elimination of in-cylinder liquid films. The effects of EGR, late intake valve closing (IVC) and fuel characteristics were investigated through their effects on efficiency, combustion stability and soot production. Results of 47% gross thermal efficiency, and 45% net thermal efficiency at stoichiometric engine operation, at up to 17 bar IMEP and 2000 r/min with 16.8:1 r c were achieved with LPG. Estimated brake efficiency values were compared to a contemporary medium duty diesel engine illustrating the benefits of the chosen path for achieving diesel efficiency parity.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2016

Evaluation of Knock Behavior for Natural Gas - Gasoline Blends in a Light Duty Spark Ignited Engine

The compression ratio is a strong lever to increase the efficiency of an internal combustion engine. However, among others, it is limited by the knock resistance of the fuel used. Natural gas shows a higher knock resistance compared to gasoline, which makes it very attractive for use in internal combustion engines. The current paper describes the knock behavior of two gasoline fuels, and specific incylinder blend ratios with one of the gasoline fuels and natural gas. The engine used for these investigations is a single cylinder research engine for light duty application which is equipped with two separate fuel systems. Both fuels can be used simultaneously which allows for gasoline to be injected into the intake port and natural gas to be injected directly into the cylinder to overcome the power density loss usually connected with port fuel injection of natural gas. Adding natural gas at wide open throttle helps to reduce knock mitigating measures and increases the efficiency and power density compared to the other gasoline type fuels with lower knock resistance. The used methods, knock intensity and number of pressure waves, do not show significant differences in knock behavior for the natural gas - gasoline blends compared to the gasoline type fuels. A knock integral was used to describe the knock onset location of the fuels tested. Two different approaches were used to determine the experimental knock onset and were compared to the knock onset delivered by the knock integral (chemical knock onset). The gasoline type fuels show good agreement between chemical and experimental knock onset. However, the natural gas -gasoline blends show higher discrepancies comparing chemical and experimental knock onset.

Advanced Combustion Concept↗