SEARCH · Search NASA

Results for “GIMBAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Redundant single gimbal control moment gyroscope singularity analysis

The robotic manipulator is proposed as the mechanical analog to single gimbal control moment gyroscope systems, and it is shown that both systems share similar difficulties with singular configurations. This analogy is used to group gimbal angles corresponding to any momentum state into different families. The singularity problem associated with these systems is examined in detail. In particular, a method is presented to test for the possibility of nontorque-producing gimbal motion at a singular configuration, as well as to determine the admissible motions in the case when this is possible. Sufficient conditions are derived for instances where the singular system can be reconfigured into a nonsingular state by these nontorque-producing motions.

Bedrossian, Nazareth S.↗

NASA NTRS1994

The Determination of Forces and Moments on a Gimballed SRM Nozzle Using a Cold Flow Model

The Solid Rocket Motor Air Flow Facility (SAF) at NASA Marshall Space Flight Center was used to characterize the flow in the critical aft end and nozzle of a solid propellant rocket motor (SRM) as part of the design phase of development. The SAF is a high pressure, blowdown facility which supplies a controlled flow of air to a subscale model of the internal port and nozzle of a SRM to enable measurement and evaluation of the flow field and surface pressure distributions. The ASRM Aft Section/Nozzle Model is an 8 percent scale model of the 19 second burn time aft port geometry and nozzle of the Advanced Solid Rocket Motor, the now canceled new generation space Shuttle Booster. It has the capability to simulate fixed nozzle gimbal angles of 0, 4, and 8 degrees. The model was tested at full scale motor Reynolds Numbers with extensive surface pressure instrumentation to enable detailed mapping of the surface pressure distributions over the nozzle interior surface, the exterior surface of the nozzle nose and the surface of the simulated propellant grain in the aft motor port. A mathematical analysis and associated numerical procedure were developed to integrate the measured surface pressure distributions to determine the lateral and axial forces on the moveable section of the nozzle, the effective model thrust and the effective aerodynamic thrust vector (as opposed to the geometric nozzle gimbal angle). The nozzle lateral and axial aerodynamic loads and moments about the pivot point are required for design purposes and require complex, three dimensional flow analyses. The alignment of the thrust vector with the nozzle geometric centerline is also a design requirement requiring three dimensional analyses which were supported by this experimental program. The model was tested with all three gimbal angles at three pressure levels to determine Reynolds number effects and reproducibility. This program was successful in demonstrating that a measured surface pressure distribution could be integrated to determine the lateral and axial loads, moments and thrust vector alignment for the scaled model of a large space booster nozzle. Numerical results were provided which are scaleable to the full scale rocket motor and can be used as benchmark data for 3-D CFD analyses.

Whitesides, R. Harold↗

NASA NTRS2006

Failure of Harmonic Gears During Verification of a Two-Axis Gimbal for the Mars Reconnaissance Orbiter Spacecraft

The Mars Reconnaissance Orbiter (MRO) spacecraft has three two-axis gimbal assemblies that support and move the High Gain Antenna and two solar array wings. The gimbal assemblies are required to move almost continuously throughout the mission's seven-year lifetime, requiring a large number of output revolutions for each actuator in the gimbal assemblies. The actuator for each of the six axes consists of a two-phase brushless dc motor with a direct drive to the wave generator of a size-32 cup-type harmonic gear. During life testing of an actuator assembly, the harmonic gear teeth failed completely, leaving the size-32 harmonic gear with a maximum output torque capability less than 10% of its design capability. The investigation that followed the failure revealed limitations of the heritage material choices that were made for the harmonic gear components that had passed similar life requirements on several previous programs. Additionally, the methods used to increase the stiffness of a standard harmonic gear component set, while accepted practice for harmonic gears, is limited in its range. The stiffness of harmonic gear assemblies can be increased up to a maximum stiffness point that, if exceeded, compromises the reliability of the gear components for long life applications.

Johnson, Michael R.↗

NASA NTRSDate not supplied

Autonomous Constrained Control for Arbitrary Thruster Configurations of Gimbaling Thrusters in SE(3)

In order to develop robust autonomy in spacecraft, it is desirable to develop methods for guiding and controlling arbitrarily-configured spacecraft with any combination of thrusters of various types, i.e. either static reaction control system thrusters and gimbaling thrusters. Scenarios in which autonomous selection of thrusters may be needed include the case of a stuck or inhibited thruster that restricts the motion of the vehicle, vehicles with changing mass properties such as logistics modules or tugs, or vehicles that have imposed constraints on thrusters during docking in order to avoid plume impingement on a space station or adjacent spacecraft. To that end, a spacecraft must be able to rapidly and autonomously reconfigure thruster firing histories and update guidance protocols in accordance with newly imposed constraints. In this paper, a methodology is presented that enables a spacecraft to autonomously select thrusters of any configuration and type in order to optimally match a desired 6-degree-of-freedom navigation and control within the special Euclidean SE(3) framework. The residual motion imposed by off-nominal thruster configurations or thrusters that are not fully controllable is identified by the spacecraft and solved for over time, both for static reaction control systems and for the case of gimbaling thrusters.

GN&C↗

NASA NTRS1967

Gimbaled-mirror scanning system capable of spiral pattern

Gimbaled-mirror infrared radiation scanner, with a lightweight torque motor direct coupled to each axis, is capable of scanning in a highly efficient spiral pattern. The scanner is lightweight and can be remotely positioned in previously inaccessible areas because the radiometer head and the gimbaled-mirror scanner can be separated.

Haertsch, O. C.↗

NASA NTRS1968

Gimbal angle sensor

Detector flake located parallel to a slotted mask mechanical differentiator, senses the rotation of a gimballed reaction wheel mounting. As the gimbal moves light passes through the mask and strikes a section of the detector, the electrical output of which has been calibrated in terms of degrees of rotation.

Zaremba, J. G.↗

NASA NTRS1971

The Mariner Mars 1971 gimbal actuator

The actuator that will point the gimbaled engine, thus performing the autopilot actuation function for the Mariner Mars 1971 spacecraft, is described. The gimbaled engine has two axes of freedom, providing two-axis control to the spacecraft. Motion for the two axes is provided by identical and interchangeable actuators-gearless electromechanical linear servomechanisms. Each actuator is designed to have a long service life in the space environment and to be able to function at speeds ranging from hours per cycle to cycles per second.

Perkins, G. S.↗

NASA NTRS1973

Failure management of multiple gimbal inertial systems for space shuttle

A failure detection and isolation technique for use with four gimbaled inertial measurement units (IMU) is presented. By using simulated boost and entry shuttle trajectories with specific gimbaled IMU models, failure detection thresholds are developed based on red-line life dependent requirements and warning thresholds within the red-line thresholds based on expected worst case IMU performance. Using these trajectories, established trajectory threshold, and multiple IMU models, various failure detection and isolation techniques are evaluated for application in both powered and unpowered flight phases. The adequacy of the systems for both attitude and velocity detection methods is evaluated and recommendations for space shuttle applications are made.

Dove, D. W.↗

NASA NTRS1973

Effects of certain control-system nonlinearities on stability and pointing of an attached double-gimbal experiment package in presence of random crew-motion disturbances

The effects of two types of control-system nonlinearities, sensor deadband and actuator breakout torque, on the pointing capability of a Apollo Telescope Mount (ATM) double-gimbal experiment isolation and control system are investigated. A composite structural model of a flexible experiment package connected through frictionless double gimbals to a flexible carrier vehicle is used for this investigation. Contributions of the primary carrier control system to experiment pointing are neglected. Pointing errors onboard the experiment package due to random crew-motion input into the carrier vehicle are computed. A stability investigation is performed to verify control-system stability with nominal nonlinearities and gains. Indications are that there is no stability problem due to the nonlinearities. A nonlinearity sensitivity study is carried out to determine the effects on pointing accuracy. Its results indicate that nominal ATM control system nonlinearities limit the pointing accuracy to approximately 0.4 arc second in the presence of crew motion. Methods of reducing the error to less than 0.1 arc second are discussed.

Shaughnessy, J. D.↗

NASA NTRS1974

Investigation of application of two-degree-of-freedom dry tuned-gimbal gyroscopes to strapdown navigation systems

The work is described which was accomplished during the investigation of the application of dry-tuned gimbal gyroscopes to strapdown navigation systems. A conventional strapdown configuration, employing analog electronics in conjunction with digital attitude and navigation computation, was examined using various levels of redundancy and both orthogonal and nonorthogonal sensor orientations. It is concluded that the cost and reliability performance constraints which had been established could not be met simultaneously with such a system. This conclusion led to the examination of an alternative system configuration which utilizes an essentially new strapdown system concept. This system employs all-digital signal processing in conjunction with the newly-developed large scale integration (LSI) electronic packaging techniques and a new two-degree-of-freedom dry tuned-gimbal instrument which is capable of providing both angular rate and acceleration information. Such a system is capable of exceeding the established performance goals.

Source record↗

NASA NTRS1974

Stability study of the Large Space Telescope /LST/ system with nonlinear CMG gimbal friction

The purpose of the investigation reported upon is to study the existence and characteristics of self-sustained oscillations in the dynamic behavior of the Large Space Telescope (LST) system due to the presence of nonlinear gimbal friction in the control moment gyroscopes (CMGs). A continuous-data single-axis model of the LST is considered. A solid friction model is used to represent CMG gimbal friction. A rigorous mathematical model is derived for use in a continuous describing function analysis. Conditions for self-sustained oscillations are then determined.

Kuo, B. C.↗

NASA NTRS1975

A steering law for three double-gimbal control moment gyro systems

A steering law for three double-gimbal control moment gyro (CMG) systems is proposed. This steering law is applicable to systems with almost any configuration of CMGs and the CMG-out operation needs no special modification. Examples of three double gimbal CMG systems in an orthogonal configuration and in a parallel configuration are shown along with the results of digital simulations. Simulation results show that any command torque can always be met except when the system is in a singular state and that, whenever the system is in, or close to, a singularity, the steering law drives the system state out of the vicinity of the singularity.

Yoshikawa, T.↗

NASA NTRS1974

An analysis of the Dahl friction model and its effect on a CMG gimbal rate controller

The effects of friction, represented by the Dahl model, on a CMG rate control system was investigated by digital simulation. The conclusion from these simulation results is that gimbal pivot friction can be a significant effect on the gimbal rate control system. The magnitude of the problem this presents depends on the characteristics of the actual pivot. It would appear from this preliminary look that one solution is to insure that the control system natural frequency is higher by some prescribed amount than the natural frequency of the friction loop.

Nurre, G. S.↗

NASA NTRS1976

Analytical study of inside-out Gimbal dynamics. Volume 2: Appendix

Stability data, eigenvalue data, and instrument pointing system earth point tracking time histories at various orbital altitudes are presented. These data apply to the inside-out Gimbal system configuration and the coincident Gimbal system configuration.

Rybak, S. C.↗

NASA NTRS1980

Ku band deployed assembly and gimbal

Requirements for shuttle orbiter missions to locate satellites for servicing and to communicate when out of touch with a direct ground link were established. A Ku Band deployed antenna system providing an integrated radar and communications function was designed to meet these requirements. The unique features of the gimbal assembly are described with emphasis on the following: edge mounted antenna to minimize stowage volume in shuttle and maximize gain; unique two axis housing and shaft arrangement to accommodate two runs of waveguide and 55 electrical conductors without requiring slip rings; maximum use of aluminum in gimbal structure to reduce costs; and lubricant chosen to survive Earth and space environments.

Deal, T. E.↗

NASA NTRS1988

Reactionless gimbal actuator for precision pointing of large payloads

A novel actuator for application to precision pointing gimbal systems is described. The new actuator, dubbed the Reactuator, is capable of large output torques for payload pointing while minimizing reaction torques that can excite gimbal support structure. The Reactuator is able to approach reactionless operation by using an integral wheel to absorb the reaction torques. The advantages that result are described through analysis and simulation examples. Methods for designing control algorithms for the Reactuator are discussed and the results of preliminary breadboard tests are presented.

Laskin, R. A.↗

NASA NTRS1990

Internal performance of two nozzles utilizing gimbal concepts for thrust vectoring

The internal performance of an axisymmetric convergent-divergent nozzle and a nonaxisymmetric convergent-divergent nozzle, both of which utilized a gimbal type mechanism for thrust vectoring was evaluated in the Static Test Facility of the Langley 16-Foot Transonic Tunnel. The nonaxisymmetric nozzle used the gimbal concept for yaw thrust vectoring only; pitch thrust vectoring was accomplished by simultaneous deflection of the upper and lower divergent flaps. The model geometric parameters investigated were pitch vector angle for the axisymmetric nozzle and pitch vector angle, yaw vector angle, nozzle throat aspect ratio, and nozzle expansion ratio for the nonaxisymmetric nozzle. All tests were conducted with no external flow, and nozzle pressure ratio was varied from 2.0 to approximately 12.0.

Berrier, Bobby L.↗

NASA NTRS1989

Design, fabrication and test of a prototype double gimbal control moment gyroscope for the NASA Space Station

Recognizing the need to develop future technologies in support of the Space Station, NASA's Advanced Development Program (ADP) placed as its goal the design and fabrication of a prototype 4750 Newton-meter-second (3500 ft-lb-sec) Control Moment Gyroscope (CMG). The CMG uses the principle of momentum exchange to impart control torques for counteracting vehicle disturbances. This paper addresses the selection of the double gimbal CMG over the single gimbal and describes the major subassemblies of the prototype design. Particular attention is given to the choice of the materials, fabrication and design details dictated by the man-rated mission requirement. Physical characteristics and the results of functional testing are presented to demonstrate the level of system performance obtained. Comparisons are made of the measured system responses against design goals and predictions generated by computer simulation.

Blondin, Joseph↗