SEARCH · Search NASA

Results for “Glass transition temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Effects of elevated-temperature deposition on the atomic structure of amorphous Ta 2 O 5 films

Brownian thermal noise as a result of mechanical loss in optical coatings will become the dominant source of noise at the most sensitive frequencies of ground-based gravitational-wave detectors. Experiments found, however, that a candidate material, amorphous Ta 2 O 5 , is unable to form an ultrastable glass and, consequently, to yield a film with significantly reduced mechanical loss through elevated-temperature deposition alone. X-ray scattering PDF measurements are carried out on films deposited and subsequently annealed at various temperatures. Inverse atomic modeling is used to analyze the short and medium range features in the atomic structure of these films. Furthermore, in silico deposition simulations of Ta 2 O 5 are carried out at various substrate temperatures and an atomic level analysis of the growth at high temperatures is presented. It is observed that upon elevated-temperature deposition, short range features remain identical, whereas medium range order increases. After annealing, however, both the short and medium range orders of films deposited at different substrate temperatures are nearly identical. A discussion on the surface diffusion and glass transition temperatures indicates that future pursuits of ultrastable low-mechanical-loss films through elevated temperature deposition should focus on materials with a high surface mobility, and/or lower glass transition temperatures in the range of achievable deposition temperatures.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Anomalously strong viscosity behavior in mixed oxy-sulfide Na 4 P 2 S 7-x O x invert glasses

In this paper, the first observations have been made of anomalously strong viscosity behavior and correspondingly strong bulk glass formation and resistance to crystallization in a melt quenched (MQ) prepared series of invert, modifier content greater than the glass former content, mixed oxy-sulfide Na 4 P 2 S 7-x O x , 0 ≤ x ≤ 5, (NaPSO) glasses. We find that these glasses even with 67 mole % modifier, Na 2 S, and only 33 mole% glass former P 2 S 5-x O x , exhibit a calorimetric fragility index, m cal , as small as 29 compared to typical values of ~ 60 to 80 for alkali silicate glasses with > 50 mole% SiO 2 and the theoretical minimum m cal of ~ 15. The m cal values were converted to kinetic viscosity fragility, m vis , values and used with the measured glass transition temperatures, T g s, to produce viscosity curves for the glasses using the Mauro-Yue-Ellison-Gupta-Allan (MYEGA) model. The viscosity of the glass with a minimum m cal value of x = 2.5 was then shown to exhibit a viscosity that was as strong as, and for some compositions stronger than, the viscosity of alkali aluminosilicate glasses which have three dimensional network structures compared to the one dimensional chain structures observed in these MOS invert glasses. Consistent with these small values of fragility indices and therefore predicted higher viscosity above the glass transition temperature, T g , in the supercooled liquid regime, these glasses are also particularly resistant to crystallization. For example, the x = 2.5 glass composition exhibits a crystallization temperature, T C , more than 150K above its T g . We find that the calorimetric fragility of these glasses varies systematically with the extent of network forming bridging oxygens (BOs) in the glasses. The structural change caused by incrementally replacing sulfur with oxygen has been found to have consistent, large effects on the thermal properties.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Key Factors in Semi-Generic Coarse-Grained Modeling of Solid Polymer Electrolytes

Given the long length and time scales of interest and strong interactions present in solid polymer electrolytes, coarse-grained molecular models can be useful in understanding the molecular basis of their structure and transport properties. Rather than representing atoms individually, coarse-grained models use beads representing groups of atoms, making the system simpler and more efficient. Generic coarse-grained models, that are not built based on matching a particular atomistic system, can provide insight into the important physical considerations that apply across different chemical systems, though it can be unclear how to best match to experimental systems and capture relevant experimental behaviors with as simple of a model as possible. Here, we build on generic bead-spring models, but use stiff angle potentials, set different bead properties for different polymer types, and include additional ion parameters, creating a semi-generic coarse-grained model that can map more specifically to polymers and copolymers with different chain architectures, component glass transition temperatures, and ion solvation behaviors. We set most parameters with basic homopolymer data such as glass transition temperatures, Kuhn length, density, and dielectric constant, with further adjustment based on data from the polymer electrolyte system. We specifically model polystyrene-block-poly(oligo-oxyethylene methyl ether methacrylate) (PS-b-POEM) with lithium triflate salt, considering the POEM to be made of a poly(methylmethacrylate) backbone with poly(ethylene oxide) side chains. Solvation of ions is accounted for by additional polymer-ion interactions of the form -S/r4, plus additional lithium-polymer Lennard-Jones interactions. We find these potentials have different effects and discuss strategies for setting these parameters.

Zhang, Yuanhao↗

DOE OSTI2023

Segmental relaxation of sequence defined polymers

For this work, the dynamical behavior of sequence defined polymers, P(C n EG 4 ), was studied using dielectric spectroscopy showing one segmental relaxation in addition to a secondary relaxation. In case of segmental relaxation, the relaxation times strongly depend on the molecular weight at low temperatures, while at higher temperatures, unlike to linear homo polymers, this effect levels out. With increasing length of C-units, the segmental relaxation accelerates. This is also reflected in the glass transition temperature, extracted from dielectric spectroscopy. With increasing length of C-units the glass transition temperature decreases, compatible with the accelerated segmental relaxation.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Effect of network connectivity on behavior of synthetic Broborg hillfort glasses

There is wide industrial interest in developing robust models of long-term (>100 years) glass durability. Archeological glass analogs, glasses of similar composition, and alteration conditions to those being tested for durability can be used to evaluate and inform such models. Two such analog glasses from a 1500-year-old vitrified hillfort near Uppsala, Sweden have previously been identified as potential analogs for low concentration Fe-bearing aluminosilicate nuclear waste glasses. However, open questions remain regarding the melting environment from which these historic glasses were formed and the effect of these conditions on their chemical durability. A key factor to answering the previous melting and durability questions is the redox state of Fe in the starting and final materials. Past work has shown that the melting conditions of a glass-forming melt may influence the redox ratio value (Fe +3 /ΣFe), a measure of a glass's redox state, and both melting conditions and the redox ratio may influence the glass alteration behavior. Synthetic analogs of the hillfort glasses have been produced using either fully oxidized or reduced Fe precursors to address this question. In this study, the melting behavior, glass transition temperature, oxidation state, network structure, and chemical durability of these synthesized glass analogs is presented. Resulting data suggests that the degree of network connectivity as impacted by the oxidation state of iron impacted the behavior of the glass-forming melt but in this case does not affect the chemical durability of the final glass. Glasses with a lower degree of melt connectivity were found to have a lower viscosity, resulting in a lower glass transition temperature and softening temperature, as well as in a lower temperature of foam onset and temperature of foam maximum. This lower degree of network connectivity most likely played a more significant role in accelerating the conversion of batch chemicals into glass than the presence of water vapor in the furnace's atmosphere. Future work will focus on using the results from this work with outcomes from other aspects of this project to evaluate long-term glass alteration models.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Low temperature aging in a molecular glass: the case of cis -methyl formate

Glassy films of cis-methyl formate show spontaneous dipole orientation on deposition from the vacuum, the so-called ‘spontelectric effect’, creating surface potentials and electric fields within the films. We follow the decay of these fields, and their accompanying dipole orientation, on the hours timescale at deposition temperatures between 40 K and 55 K. Our data trace the low temperature ‘secondary decay’ mechanism, at tens of degrees below the glass transition temperature of 90 K. We show that secondary decay is due to molecular rotation, with associated activation energies lying between 0.1 and 0.2 eV. Diffusion is absent, as established from published neutron reflectivity data. Using an analytical model for the spontelectric effect, data are placed on a quantitative footing, showing that angular motion in excess of 50° reproduces the observed values of activation energies. Exploitation of the spontelectric effect is new in the study of glass aging and is shown here to give insight into the elusive processes which take place far from the molecular glass transition temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Exploring the Ion Solvation Environments in Solid-State Polymer Electrolytes through Free-Energy Sampling

The success of poly(ethylene oxide) (PEO) in solid-state polymer electrolytes for lithium-ion batteries is well established. Recently, in order to understand this success and to explore possible alternatives, we studied polyacetal electrolytes to deepen the understanding of the effect of the local chemical structure on ion transport. Advanced molecular dynamics techniques using newly developed, tailored interaction potentials have helped elucidate the various coordination environments of ions in these systems. In particular, the competition between cation-Anion pairing and coordination by the polymer has been explored using free-energy sampling (metadynamics). At equivalent reduced temperatures, with respect to the polymer-specific glass-Transition temperature, two-dimensional free-energy plots reveal the existence of multiple coordination environments for the lithium (Li) ions in these systems and their relative stabilities. Furthermore, we observe that the Li-ion movement in PEO follows a serial, stepwise pathway when moving from one coordination state to another, whereas this happens in a more continuous and concerted fashion in a polyacetal such as poly(1,3-dioxalane) [P(EO-MO)]. The implication is that interconversion between coordination states of the Li ions may be easier in P(EO-MO). However, the overarching observation from our free-energy analysis is that Li-ion coordination is dominated by the polymer (in either case) and contact-ion pairs are rare. We rationalize the observed higher increase in glass-Transition temperature (Tg) with salt loading in polyacetals as due to intermolecular Li-ion coordination involving multiple polymer chains, rather than just one chain for PEO-based electrolytes. This interchain coupling in the polyacetals, resulting in the higher Tg, works against any gains due to variations in Li-ion coordination that might enhance transport processes over PEO. Further research is required to overcome the interdependence between local coordination and macroscopic properties to compete with PEO electrolytes at the same absolute working temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Experimental Determination of the Relationship Between Organic Aerosol Viscosity and Ice Nucleation at Upper Free Tropospheric Conditions

Abstract This work presents measurements of the ice nucleating ability of secondary organic material recorded between −40 and −70°C and relative humidity with respect to ice (RH ice ) between 150% and 220%. For a subset of systems, temperature and humidity dependence of particle viscosity as well as dry glass transition temperature were characterized using the dual tandem differential mobility analyzer method. Eleven unique monoterpene, sesquiterpene and aromatic precursors were used to generate secondary organic material (SOM) using either an oxidation flow reactor (OFR) or an environmental chamber (EC). For the SOM for which viscosity was measured, the particle glass transition temperatures varied between 6 and 23°C ( n = 8). Measurements were performed to verify that increased relative humidity did not plasticize the particles below −10°C at residence times similar to those in the ice nucleation instrument. No heterogeneous ice nucleation was observed at the ∼0.5% onset threshold for any of the materials generated. The ice nucleation occurs by the freezing of SOM solution droplets consistent with homogeneous freezing indicating that they form an aqueous solution, or the SOM particles required water saturation to freeze, indicating that they were hydrophobic. Experiments exploring the influence of functional groups and mass loading did not reveal any obvious influence of particle chemistry or generation conditions on the results. Close structural matches between known organic ice nucleating particles as precursor or formed products did not yield materials that promoted freezing. These experiments suggest that heterogeneous ice formation of glassy secondary organic materials is likely uncommon under upper free tropospheric conditions.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Hygrothermal Aging and Thermomechanical Characterization of As-Manufactured Tidal Turbine Blade Composites

This study investigates the hygrothermal aging behavior and thermomechanical properties of as-manufactured glass fiber-reinforced epoxy and thermoplastic composite tidal turbine blades. The blades were previously deployed in a marine environment and subsequently analyzed through a comprehensive suite of material characterization techniques, including hygrothermal aging, dynamic mechanical analysis (DMA), tensile testing and X-ray computed tomography (XCT). Hygrothermal aging experiments revealed that while thermoplastic composites exhibited lower overall water absorption (0.78% vs. 0.47%), they had significantly higher diffusion coefficients than epoxy (2.1 vs. 12.1 × 10 −13 m 2 s −1 ), suggesting faster saturation in operational environments. DMA results demonstrated that water ingress caused plasticization in epoxy matrices, reducing the glass transition temperature and increasing damping (112 °C to 104 °C), while thermoplastic composites showed more stable thermal behavior (87 °C glass transition temperature). Tensile testing revealed substantial reductions in ultimate strength (>40%) for both materials after prolonged water exposure, with minimal change in elastic modulus, highlighting the role of matrix degradation over fiber reinforcement. XCT image analysis showed that both composites were manufactured with high quality: no large voids or cracks were present, and the degree of misalignment was low. These findings inform future marine renewable energy composite designs by emphasizing the critical influence of moisture on long-term structural integrity and the need for optimized material systems in harsh marine environments. This work provides a rare real-world comparison of epoxy and recyclable thermoplastic tidal turbine blades, showing how laboratory aging tests and advanced imaging reveal the influence of material and manufacturing choices on long-term marine durability.

16 TIDAL AND WAVE POWER↗

DOE OSTI2025

Adhesion of Self-Complementary, Sinusoidal Surfaces Fabricated Using Two-Photon Polymerization

Microscale, pick-and-place assembly is a non-lithographic assembly method poised to impact diverse fields including flexible electronics, microfluidics and robotics. However, a major technological challenge is the need to deterministically control adhesion between parts. Here, switchable adhesion involving 3D-printed, self-complementary surfaces is demonstrated. Mechanical properties of metasurfaces pressed against flat, rigid substrates are modeled using finite element methods. A series of flat slabs and metastructured slabs with 2D sinusoidal surfaces are printed using two-photon polymerization (2PP) of a shape-memory resin. The surface frequency of featured slabs was varied between $3.\bar3$ mm −1 and $26.\bar6$ mm −1 with similar amplitudes. Adhesion between printed metasurfaces and glass and between printed, self-complementary metasurfaces is studied above and below the cured resin’s glass transition temperature (∼45 °C). Simple heating of adhering surfaces to above 60 °C lowers adhesion, and compression of surfaces while above the glass transition temperature followed by cooling to room temperature elevates adhesion. The nominal adhesive strength between printed, self-complementary surfaces, as determined by the maximum observable pull-off stress, exceeds 3 MPa. Further tailoring complementary surfaces for adhesion control may facilitate microscale disassembly for recovery of components or precious metals.

amorphous materials↗

DOE OSTI2024

Hygrothermal aging and recycling effects on mechanical and thermal properties of recyclable thermoplastic glass fiber composites

Abstract Glass fiber‐reinforced polymer composites are widely used in marine applications, including renewable energy devices and submarines, due to their strength‐to‐weight ratios and corrosion resistance. As sustainability becomes more important, recyclable thermoplastic composites are gaining attention in marine energy applications. These materials face harsh conditions such as high chloride water, UV radiation, pressurization, and thermal cycling, which can affect their durability and recyclability. This study examines the impact of hygrothermal aging on the recyclability of an Elium glass fiber (GF) composite. Samples were mechanically ground for recycling, and mechanical and thermal properties were compared between aged and unaged samples. After seawater aging, the tensile strength and modulus of the unaged composite dropped by 25% and 13% respectively, due to water ingress along the fiber‐matrix interface. The recycled composite showed reduced flexural strength as the long fiber composite was converted into short fibers during the process. Differential scanning calorimetry (DSC) revealed no change in glass transition temperature after aging. Weight loss (25%) was attributed to the thermal stability of the glass fibers. Dynamic mechanical analysis (DMA) showed that the storage modulus increased with aging, and fracture analysis confirmed a mixed mode of failure for aged composites. Highlights Hygrothermal aging lowers mechanical performance of Elium® GF composites. Failure mechanism tends to be matrix cracking and interface bonding. Glass transition temperature is not reduced by hygrothermal aging. Fractured composite was successfully recycled via thermoforming. Flexural strength of the recycled composite is lower.

17 WIND ENERGY↗

DOE OSTI2024

Thermally stable and self-healable lignin-based polyester

The increased use of plastics and the associated environmental impact has catalyzed research on the development of bio-derived polymers. Bio-based polyesters have gained increased attention due to the abundance of their starting materials and ease of processing. Lignin is naturally occurring in biomass with rich carbon content, whose functionality and rigidity make it an ideal bio-derived candidate for bio-based polyesters. Herein, a lignin-based polyester with good thermal stability and self-repairability was synthesized from carboxylated lignin and epoxidized soybean oil. The synthesized lignin/epoxidized soybean oil (ESO) vitrimer was brittle such that its mechanical performance could not be recorded. However, when polyethylene glycol (PEG) was incorporated as a plasticizer, polymer samples exhibited acceptable ductility. From thermomechanical analysis of the synthesized polyesters, the plasticizer did not impair thermal stability of polymers, but greatly enhanced mechanical properties. Notably, all samples exhibited stability at high temperatures, and good glass transition temperatures (51.0 ± 0.9–78.0 ± 1.2 °C). The highest tensile strength (3.983 ± 0.1 MPa) and storage modulus (1463.67 ± 12.6 MPa) were recorded for the polyester containing 6 % w/w PEG. Moreover, the polymer samples exhibited self-healing capability at 180 °C. This work expands on valorization of lignin through the synthesis of bio-derived materials.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Role of Intradomain Heterogeneity on Ion and Polymer Dynamics in Block Polymer Electrolytes: Investigating Interfacial Mobility and Ion-Specific Dynamics and Transport

Block polymers show promise as solid-state battery electrolytes due to the optimization of conductive and mechanical properties enabled via tuning of block chemistry and length. We investigate a polystyrene-block-poly(oligo-oxyethylene methacrylate) (PS-b-POEM) electrolyte doped with various lithium salts to investigate the role of molecular structure on ion transport properties and on local ion dynamics and associations. Anion charge becomes more delocalized with increasing size, reducing the coupling between salt ions while increasing coupling between ion and polymer chain motions and creating a more mobile overall environment. We observe support for this ion-polymer coupling via 1 H, 7 Li and 19 F NMR spectroscopy, from which we obtain ion-specific mobility transition temperatures that differ from the polymer glass transition temperature. We also note faster transport and weaker local energetic interactions with anion size using temperature-dependent NMR diffusometry. 1 H NMR spectroscopy further elucidates polymer chain dynamics and enables quantification of the temperature-dependent fraction of the conducting block that is immobile near the PS-POEM domain interface. As a result, NMR thus represents a species-specific and timescale-specific platform to quantify phase and interface behavior, and to correlate ion-specific transport with polymer chain dynamics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Thiol–ene Click Chemistry Incorporates Hydroxyl Functionality on Polycyclooctene to Tune Properties

Polyolefins compose the majority of plastic waste, but conventional mechanical recycling degrades their properties, thereby reducing their value. We report the functionalization of a model for dehydrogenated polyethylene, polycyclooctene (PCOE), with thiol–ene click chemistry to install pendant hydroxyl ethyl thioethers. Functionalization of PCOE using mercaptoethanol via thiol–ene click chemistry yielded functionalization between 1.4 and 22.9% based on ethylene monomeric units. Reactions were well-controlled by varying the reagent stoichiometry and reaction time. Crystallinity and melting temperature decreased, and glass transition temperature increased with greater functionalization. Contact angle measurements reveal an increase in surface polarity with functionalization. Here, comparisons with poly(ethylene-co-vinyl alcohol) (EVOH) show comparable surface polarity at similar levels of alcohol functionalization. At 12% functionalization, the ultimate shear stress (USS) of functionalized PCOE in an adhesive configuration is 4.10 ± 0.48 MPa, comparable to EVOH. At >12% functionalization, the failure mode changed from adhesive to mixed adhesive–cohesive, and the USS decreased.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Morphology of poly-3-hexyl-thiophene blends with styrene–isoprene–styrene block-copolymer elastomers from X-ray and neutron scattering

The nano- and micron scale morphology of poly(3-hexylthiophene) (P3HT) and polystyrene-block-polyisoprene-block-polystyrene (PS–PI–PS) elastomeric blends is investigated through the use of ultra-small and small angle X-ray and neutron scattering (USAXS, SAXS, SANS). It is demonstrated that loading P3HT into elastomer matrices is possible with little distortion of the elastomeric structure up to a loading of ~5 wt%. Increased loadings of conjugated polymer is found to significantly distort the matrix structure. Changes in processing conditions are also found to affect the blend morphology with especially strong dependence on processing temperature. Processing temperatures above the glass transition temperature (T g ) of polystyrene and the melting temperature (T m ) of the conjugated polymer additive (P3HT) creates significantly more organized mesophase domains. P3HT blends with PS–PI–PS can also be flow-aligned through processing, which results in an anisotropic structure that could be useful for the generation of anisotropic properties (e.g. conductivity). Moreover, the extent of flow alignment is significantly affected by the P3HT loading in the PS–PI–PS matrix. The work adds insight to the morphological understanding of a complex P3HT and PS–PI–PS polymer blend as conjugated polymer is added to the system. Here, we also provide studies isolating the effect of processing changes aiding in the understanding of the structural changes in this elastomeric conjugated polymer blend.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Calibrating the SPECTACULAR constitutive model using legacy Sandia data for two filled epoxy systems: 828/CTBN/DEA/GMB and 828/DEA/GMB

The SPECTACULAR model is a development extension of the Simplified Potential Energy Clock (SPEC) model. Both models are nonlinear viscoelastic constitutive models used to predict a wide range of time-dependent behaviors in epoxies and other glass-forming materials. This report documents the procedures used to generate SPECTACULAR calibrations for two particulate-filled epoxy systems, 828/CTBN/DEA/GMB and 828/DEA/GMB. No previous SPECTACULAR or SPEC calibration exists for 828/CTBN/DEA/GMB, while a legacy SPEC calibration exists for 828/DEA/GMB. To generate the SPECTACULAR calibrations, a step-by-step procedure was executed to determine parameters in groups with minimal coupling between parameter groups. This procedure has often been deployed to calibrate SPEC, therefore the resulting SPECTACULAR calibration is backwards compatible with SPEC (i.e. none of the extensions specific to SPECTACULAR are used). The calibration procedure used legacy Sandia experimental data stored on the Polymer Properties Database website. The experiments used for calibration included shear master curves, isofrequency temperature sweeps under oscillatory shear, the bulk modulus at room temperature, the thermal strain during a temperature sweep, and compression through yield at multiple temperatures below the glass transition temperature. Overall, the calibrated models fit the experimental data remarkably well. However, the glassy shear modulus varies depending on the experiment used to calibrate it. For instance, the shear master curve, isofrequency temperature sweep under oscillatory shear, and the Young's modulus in glassy compression yield values for the glassy shear modulus at the reference temperature that vary by as much as 15 %. Also, for 828/CTBN/DEA/GMB, the temperature dependence of the glassy shear modulus when fit to the Young's modulus at different temperatures is approximately four times larger than when it is determined from the isofrequency temperature sweep under oscillatory shear. For 828/DEA/GMB, the temperature dependence of the shear modulus determined from the isofrequency temperature sweep under oscillatory shear accurately predicts the Young's modulus at different temperatures. When choosing values for the shear modulus, fitting the glassy compression data was prioritized. The new and legacy calibrations for 828/DEA/GMB are similar and appear to have been calibrated from the same data. However, the new calibration improves the fit to the thermal strain data. In addition to the standard calibrations, development calibrations were produced that take advantage of development features of SPECTACULAR , including an updated equilibrium Helmholtz free energy that eliminates undesirable behavior found in previous work. In addition to the previously mentioned experimental data, the development calibrations require data for the heat capacity during a stress-free temperature sweep to calibrate thermal terms.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Temperature-induced densification in compressed basaltic glass revealed by in-situ ultrasonic measurements

Abstract Acoustic velocities of a model basalt glass (64 mol% CaMgSi2O6 + 36 mol% CaAl2Si2O8) were measured along different pressure-temperature (P-T) paths. One set of experiments involved isothermal compression-decompression cycles, performed at temperatures of 300, 641, 823, and 1006 K and pressures up to 12.2 GPa. The other set of experiments involved constant-load heating-cooling cycles at temperatures up to 823 K and pressures up to 7.5 GPa. Both sets of experiments were performed in a multi-anvil apparatus using a synchrotron-based ultrasonic technique. Our results show that the glass compressed isothermally at 300 K (cold-compression) displays anomalously decreasing compressional (VP) and shear (VS) wave velocities with increasing pressure until ~8 GPa. Beyond 8 GPa, both VP and VS start to increase sharply with pressure and irreversible densification of the glass occurred, producing large hysteresis loops of velocities upon decompression. However, for the glass compressed isothermally at increasingly higher temperatures (hot-compression), the velocity minima gradually shift to lower pressures. At temperature close to the glass transition temperature Tg, the velocity minima disappear completely, displaying a monotonic increase of velocities during compression and higher VP and VS during decompression. In addition, constant-load heating-cooling experiments show that velocities generally decrease slightly with increasing temperature, but start to increase once heated above a threshold temperature (~650 K). During cooling the velocities increase almost linearly with decreasing temperature, resulting in higher velocities (~1.5–2.5% higher) when returned to 300 K. This implies that a temperature-induced densification may have occurred in the glass at high pressures. Raman spectra on recovered samples show that the hot-compressed and high-P heated glasses contain distinctly densified and depolymerized structural signatures compared to the initial glass and the cold-compressed glass below the velocity transition pressure PT (~8 GPa). Such densification may be attributed to the breaking of bridging oxygen bonds and compaction in the intermediate-range structure. Our results demonstrate that temperature can facilitate glass densification at high pressures and point out the importance of P-T history in understanding the elastic properties of silicate glasses. Comparison with melt velocity suggests that hot-compressed glasses may better resemble the pressure dependence of velocity of silicate melts than cold-compressed glasses, but still show significantly higher velocities than melts. If the abnormal acoustic behaviors of cold-compressed glasses were used to constrain melt fractions in the mantle low-velocity regions, the melt fractions needed to explain a given velocity reduction would be significantly underestimated at high pressures.

Geochemistry & Geophysics↗

DOE OSTI2020

Combined light- and heat-induced shape memory behavior of anthracene-based epoxy elastomers

Abstract The development of multi-stimuli-responsive shape memory polymers has received increasing attention because of its scientific and technological significance. In this work, epoxy elastomers with reversible crosslinks are synthesized by polymerizing an anthracene-functionalized epoxy monomer, a diepoxy comonomer, and a dicarboxylic acid curing agent. The synthesized elastomers exhibit active responses to both light and heat enabled by the incorporated anthracene groups. When exposed to 365 nm UV light, additional crosslinking points are created by the photo-induced dimerization of pendant anthracene groups. The formation of the crosslinking points increases modulus and glass transition temperature of the elastomers, allowing for the fixation of a temporary shape at room temperature. The temporary shape remains stable until an external heat stimulus is applied to trigger the scission of the dimerized anthracene, which reduces the modulus and glass transition temperature and allows the elastomers to recover their original shapes. The effects of external stimuli on the thermal and dynamic mechanical properties of the elastomers are investigated experimentally and are correlated with molecular dynamics simulations that reveal the changes of structure and dynamics of the anthracene molecules and flexible chains.

36 MATERIALS SCIENCE↗