Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Shear-Coupled Grain Growth and Texture Development in a Nanocrystalline Ni-Fe Alloy during Cold Rolling

The evolution of texture, grain size, grain shape, dislocation and twin density has been determined by synchrotron X-ray diffraction and line profile analysis in a nanocrystalline Ni- Fe alloy after cold rolling along different directions related to the initial fiber and the long axis of grains. The texture evolution has been simulated by the Taylor-type relaxed constraints viscoplastic polycrystal model. The simulations were based on the activity of partial dislocations in correlation with the experimental results of dislocation density determination. The concept of stress-induced shear-coupling is supported and strengthened by both the texture simulations and the experimentally determined evolution of the microstructure parameters. Grain-growth and texture evolution are shown to proceed by the shear-coupling mechanism supported by dislocation activity as long as the grain size is not smaller than about 20 nm.

Dislocation mechanism of grain growth↗

Evolution of microstructure and microtexture during hot deformation in an advanced P/M nickel base superalloy

Highlights: • Microstructural evolution of PM superalloy sensitive to temperature and strain rate. • Highest DRX with finer grained structure at higher temperatures and strain rates. • Dominance of DDRX showed by serrated grain boundaries and misorientation gradient. • Weak microtextural evolution inclined towards [110] fiber compression texture seen. In the present study, the effect of hot deformation parameters on the microstructural evolution is investigated for an experimental powder metallurgy nickel superalloy. The hot isostatically pressed (HIPed) alloy is isothermally hot compressed at constant true strain rate over wide temperatures (1000 °C, 1050 °C, 1100 °C, 1150 °C) and strain rates (0.001 s{sup −1}, 0.01 s{sup −1}, 0.1 s{sup −1}, 1 s{sup −1}) regimes. Electron Back-Scattered Diffraction (EBSD) characterization of the hot deformed samples is carried out to evaluate the microstructural evolution, grain boundary characteristics, and microtextural behaviour. The strong dependence of dynamic recrystallization characteristics on the hot deformation conditions is divulged through EBSD derived colour inverse pole figure maps endorsed by grain/twin boundary characteristics and misorientation gradient. Dynamic recrystallization (DRX) is maximized at higher deformation temperatures, whereas limited DRX is observed at lower deformation temperatures, especially at higher strain rates. The dominance of discontinuous dynamic recrystallization (DDRX) is manifested through bulged/serrated grain boundaries resulting in the formation of necklace microstructure corroborated by grain boundary cumulative misorientation gradient. Although random microtexture is revealed in both deformed and recrystallized microstructures, the tendency towards the formation of 110 fiber compression texture is apparently evident.

36 MATERIALS SCIENCE↗

Dynamic Recrystallization and Grain Refinement of Fe-P-C-Si and Fe-P-C-Si-N Steels

Grain refinement is an effective technique to improve the mechanical properties of steels. In the present work, single-pass hot compression experiments have been conducted on two different compositions of high phosphorous steels to study the microstructural evolution and ferrite grain refinement at various strain rates and deformation temperatures, i.e., 0.01-10 s{sup −1} and 750-1050 °C, respectively. Optical metallography has been employed to understand the physical processes that take place during hot deformation process. The results indicate that when these compositions of high phosphorous steels are worked at relatively low temperatures in the intercritical regions, a ferrite grain size of 5-7 µm is obtained. It is observed that the grain size decreases with an increase in strain rate and with the decrease in deformation temperature. Based on the values of stress exponent (n) obtained in the present work, dislocation creep is identified as the deformation mechanism. The activation energies for deformation of these two types of high phosphorous steels have been calculated. The effect of the alloying elements on the stress–strain curve, microstructure, and grain refinement has been discussed.

36 MATERIALS SCIENCE↗

Microstructural and Property Evolution of Continuous Columnar-Grained Polycrystalline Copper during Extreme Plastic Deformation at Room Temperature

An extreme extensibility with a true strain of 11.12 has been obtained for continuous columnar-grained (CCG) polycrystalline copper at room temperature, which was cold-drawn from a 10-mm-diameter as-cast rod into a 38.5-μm-diameter ultra-fine wire without any intermediate softening heat treatment. During the extreme plastic deformation, the ultimate tensile stress increased from 140 MPa for as-cast CCG copper to 525 MPa for the deformed sample at a true stain of 11.12, while the relative electrical conductivity maintained a high value of 97.6% IACS. On this basis, CCG copper is an excellent raw material for the fabrication of ultra-fine wires with both high strength and high electrical conductivity. The original columnar grains experienced grain subdivision and formed fibrous grains along the drawing direction with a fibrous longitudinal morphology and curly transverse microstructure at medium to high strain. The subdivision of the fibrous grains then went on as the extreme plastic deformation continued. Large amounts of strain-induced boundaries and microstructural refinement facilitated the storage of abundant glide dislocations created by extreme plastic deformation. Thus, extreme plastic extensibility can be achieved through continuous work hardening of CCG copper.

36 MATERIALS SCIENCE↗

Computational and Experimental Studies of Microstructure-Scale Porosity in Metallic Fuels for Improved Gas Swelling Behavior

This proposal will investigate the stability of bimodal pore size distributions in metallic uranium and uranium-zirconium alloys during sintering and re-sintering annealing treatments. The project will utilize both computational and experimental approaches. The computational approach includes both Molecular Dynamics simulations to determine the self-diffusion coefficients in pure U and U-Zr alloys in single crystals, grain boundaries, and free surfaces, as well as calculations of grain boundary and free surface interfacial energies. Phase-field simulations using MOOSE will be conducted to study pore and grain structure evolution in microstructures with bimodal pore size distributions. Experiments will also be performed to validate the simulations, and measure the time-dependent densification of bimodal porous compacts.

36 MATERIALS SCIENCE↗

Quantification of grain rotation in bulk nanostructured copper via in situ heating white beam synchrotron X-ray diffraction

Grain rotation during microstructural relaxation under heating is conventionally studied extensively through transmission electron microscopy and simulations. However, there is a shortage in examining grain rotations at larger length and volume scales in bulk materials. It is critical to understand the thermal stability of bulk nanostructured metals, since those enhanced mechanical properties have been well recognized. Here, this study aimed to employ a white beam microdiffraction X-ray technique under in situ heating from 300 K to 1073 K at 12 K/min on a nanostructured copper processed by high-pressure torsion, yielding an initial grain size of ∼260 nm before the heating. Evaluation across a wide range of temperatures reveals transition temperatures associated with microstructural relaxation processes. By tracking separate Laue diffraction peaks stemming from individual grains, changes in their orientations can be estimated and quantified. This approach becomes particularly effective when the number of grains within the probed volume is reasonably small. At temperatures above 940 K, about 7.5 % of Cu grains are rotating at speeds of ∼2 × 10 –3 °/s. The radial direction of the disk specimen is found to be the preferred direction of grain rotation, with the rotation axis along the shear direction. Further analysis found no correlation between peak intensity and peak size, related to grain sizes and deviatoric strain, respectively, with rotation conditions or speed. These findings demonstrate that the diffraction technique utilizing white beam X-rays is a complementary and novel characterization tool for understanding microstructural evolution, especially in grain rotations, of bulk crystalline materials.

Grain orientation↗

Effect of laser melt schedule on the microstructure of additively manufactured IN718 Superalloy

Laser powder bed fusion (L-PBF) has enabled the fabrication of geometrically complex metallic structures and components that are challenging to producing using conventional manufacturing approaches. The site-specific and far from equilibrium thermal conditions of L-PBF offer the potential to facilitate multi-length scale design of structure and properties across the atomic-through macro-levels. However, L-PBF systems face scalability challenges due to throughput constraints. Laser rotary powder bed fusion (L-RPBF) systems are being investigated as a solution to enhance the deposition rates compared to conventional L-PBF. Rotary systems also offer additional flexibility for controlling the time structure of melting through laser interleaving on alternating layers. Here, in this study, IN718 test samples were printed using single-laser or interleaved dual-laser configuration in a L-RPBF system to investigates the effect of process settings and melt-interleaving on as-fabricated microstructure. The microstructural evolution, such as grain size and crystallographic texture, was assessed by determining variations in the melt-pool shapes. Laser interleaving leads to a reduction in average grain size compared to single laser by ∼ 40 % at high power (400 W) and by ∼36 % at medium power (370 W). Results presented here identify key challenge for obtaining uniform microstructures and barriers for the broader adoption of high-deposition rate L-RPBF.

Dual-laser↗

Solute stabilization of nanocrystalline tungsten against abnormal grain growth

Microstructure and phase evolution in magnetron sputtered nanocrystalline tungsten and tungsten alloy thin films are explored through in situ TEM annealing experiments at temperatures up to 1000 °C. Grain growth in unalloyed nanocrystalline tungsten transpires through a discontinuous process at temperatures up to 550 °C, which is coupled to an allotropic phase transformation of metastable β-tungsten with the A-15 cubic structure to stable body centered cubic (BCC) α-tungsten. Complete transformation to the BCC α-phase is accompanied by the convergence to a unimodal nanocrystalline structure at 650 °C, signaling a transition to continuous grain growth. Alloy films synthesized with compositions of W–20 at.% Ti and W–15 at.% Cr exhibit only the BCC α-phase in the as-deposited state, which indicate the addition of solute stabilizes the films against the formation of metastable β-tungsten. Thermal stability of the alloy films is significantly improved over their unalloyed counterpart up to 1000 °C, and grain coarsening occurs solely through a continuous growth process. The contrasting thermal stability between W–Ti and W–Cr is attributed to different grain boundary segregation states, thus demonstrating the critical role of grain boundary chemistry in the design of solute-stabilized nanocrystalline alloys.

36 MATERIALS SCIENCE↗

In-situ Phase transformation study in fine grained heat affected zone of Grade 91 steels

Creep strength-enhanced ferritic (CSEF) steels such as the 9 Cr steel [ASTM A387 Grade 91] are widely used as tubing and piping in the new generation of fossil fired power plants. Microstructures in the fine-grained heat affected zone (FGHAZ) may significantly reduce creep strength leading Type IV failures. Current research suggest that reducing pre-weld tempering temperature from 760 C (HTT) to 650 C (LTT) has the potential to double the creep life of these welds. To understand this improvement, time-resolved X-ray diffraction (TRXRD) measurement with synchrotron radiation was used to characterize the microstructure evolution during fine grained heat-affected zone (HAZ) thermal cycling of grade 91 steel. The measurements showed both M23C6 (M=Fe, Cr) and MX (M=Nb, V; X=C,N) are present in the sample after the HTT condition. Near equilibrium fraction of M23C6 was measured in high temperature tempering condition (HTT, 760 C). However, the amount of M23C6 in LTT condition was very low since the diffraction peaks are close to the background. During simulated FGHAZ thermal cycling, the M23C6 partially dissolved in HTT sample. Interestingly, MX did not dissolve in both LTT and HTT samples. Hypothesis for correlation of M23C6 carbide distribution and pre-mature creep failure in FGHAZ will be made.

Babu, Sudarsanam Suresh↗

TA [B] Predicting Microstructure-Creep Resistance Correlation in High Temperature Alloys over Multiple Time Scales

DoE-NETL partnered with Purdue University to predict the creep and associated microstructure evolution of tungsten-based refractory alloys. Researchers use grain boundary (GB) diagrams, a new concept, to establish time-dependent creep resistance and associated microstructure evolution of grain boundaries/intergranular films GB/IGF controlled creep as a function of load, environment, and temperature. The goal was to conduct a systematic study that includes the development of a theoretical framework, multiscale modeling, and experimental validation using W-based body-centered-cubic alloys, doped/alloyed with one or two of the following elements: nickel, palladium, cobalt, iron, and copper—typical refractory alloys. Prior work has already established and validated a basic theory for W-based binary and ternary alloys; the study conducted under this project extended this proven work. Based on interface diagrams phase field models were developed to predict long term microstructural evolution. In order to validate the models nanoindentation creep data was used to elucidate the role played by the interface properties in predicting long term creep strength and microstructure evolution.

20 FOSSIL-FUELED POWER PLANTS↗

Microstructure Optimization of Austenitic Alloy 800H (Fe-21Cr-32Ni)

The microstructural evolution, specifically of grain boundaries, precipitates, and dislocations in thermomechanically processed (TMP) Alloy 800H samples was characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), electron backscattered diffraction (EBSD), transmission electron microscopy (TEM), and atomic force microscopy (AFM). The TMP not only significantly increased the fraction of low-{Sigma} coincidence site lattice boundaries, but also introduced nanoscale precipitates in the matrix and altered the distribution of dislocations. Statistical analysis indicates that the morphology and distribution of grain boundary precipitates were dependent on grain boundary types. The microstructure optimization played a synergistic effect on the significantly increased strength with comparable ductility and enhanced intergranular corrosion resistance and creep-fatigue life compared to the as-received samples.

36 MATERIALS SCIENCE↗

Experimental investigation of the dependence of void nucleation and growth on initial microstructure in high-purity titanium under tension

An experimental investigation of failure mechanisms in relation to the initial microstructure in high-purity titanium samples is presented. The initial microstructure of the specimens was measured in 3D using diffraction-contrast tomography (DCT). Ex-situ X-ray computed tomography (XCT) was used to visualize voids in specimens at various levels of deformation attained by interrupted tensile testing. Electron backscatter diffraction (EBSD) mapping was used to characterize the deformed microstructures per specimen. The investigation showed that the location of failures was unrelated to the formation of the first voids, but rather the nucleation and growth of cracks were from heavily deformed surface regions. The areas surrounding the failure-causing cracks had the highest propensity for void development of any area in the specimen. This facilitated crack propagation through the specimen via “linking up”. The failure of the specimens by microvoid coalescence was bolstered by “dimpled” fracture surfaces. Paint composed of gallium embedded in rubber was used to track the displacement of points along the loading direction of the specimens, to relate the location of failure to the material's initial microstructure. However, the correlation proved difficult, due to complex microstructural evolution involving voids, grain fragmentations, and profuse twinning. Nevertheless, it was shown that necking occurred near the largest grain in the gauge section of the specimens. This is likely caused by the decrease in strength of larger grains, causing strain to concentrate in their vicinity. Here, a comprehensive picture of the failure processes in high-purity titanium under axial loading is presented and discussed in the paper.

36 MATERIALS SCIENCE↗

Effect of annealing and supercritical CO 2 exposure at 750°C on the tensile properties of stainless steel and Ni-based structural alloys

Subsize dogbone tensile specimens of alloys 304H, 310HCbN, and 740H were exposed to 30 MPa supercritical CO 2 (sCO 2 ) for up to 4000 h at 750°C. Similar exposures in laboratory air were used to assess the specific role of sCO 2 exposure on the alloy tensile properties. Type 304H specimens were only embrittled by exposure in sCO 2 due to the formation of a thick Fe-rich oxide and C ingress in the bulk of the alloy. For 310HCbN and 740H, no effect of the sCO 2 environment was observed and a decrease of the alloy's ductility was associated with previously observed microstructure evolutions, for example, grain boundary carbide formation. The 740H was tested in the solution annealed condition and self-aging took place during 750°C exposures in sCO 2 and air with the formation of fine gamma prime precipitates leading to significant tensile strength increase. It was found that both 740H and 310HCbN have adequate sCO 2 compatibility for high-temperature commercial applications.

36 MATERIALS SCIENCE↗

Evaluation of Doped-LaCrO3 ceramics for high temperature sensor applications

The main objective of this work was to investigate the applicability of the doped-LaCrO3 system for electrical interconnects and sensor applications at temperatures >800°C. Various A- and B-site doping strategies were investigated, and the effect on their electrical conductivity, Seebeck coefficient, and thermal coefficient of expansion were characterized up to 1500ºC. Solid-state, co-precipitation and sol gel methods were used to synthesize the compositions, and the chemical/thermal stability, microstructural evolution, sintering and grain growth kinetics were investigated for these compositions by XRD, SEM and Rietveld methods. The materials showing the greatest promise were included within thick film thermistor and thermocouple sensor designs that were tested to 1500ºC in various gas environments (various pO2 concentrations).

20 FOSSIL-FUELED POWER PLANTS↗

In-situ TEM observation of the response of ultrafine- and nanocrystalline-grained tungsten to extreme irradiation environments

The accumulation of defects, and in particular He bubbles, can have significant implications for the performance of materials exposed to the plasma in magnetic-confinement nuclear fusion reactors. Some of the most promising candidates for deployment into such environments are nanocrystalline materials as the engineering of grain boundary density offers the possibility of tailoring their radiation resistance properties. In order to investigate the microstructural evolution of ultrafine- and nanocrystalline-grained tungsten under conditions similar to those in a reactor, a transmission electron microscopy study with in situ 2 keV He1 ion irradiation at 9506C has been completed. A dynamic and complex evolution in the microstructure was observed including the formation of defect clusters, dislocations and bubbles. Nanocrystalline grains with dimensions less than around 60 nm demonstrated lower bubble density and greater bubble size than larger nanocrystalline (60–100 nm) and ultrafine (100–500 nm) grains. In grains over 100 nm, uniform distributions of bubbles and defects were formed. At higher fluences, large faceted bubbles were observed on the grain boundaries, especially on those of nanocrystalline grains, indicating the important role grain boundaries can play in trapping He and thus in giving rise to the enhanced radiation tolerance of nanocrystalline materials.

36 MATERIALS SCIENCE↗

Structure and migration of heavily irradiated grain boundaries and dislocations in Ni in the athermal limit

The microstructural evolution at and near preexisting grain boundaries (GBs) and dislocations in materials under high radiation doses is still poorly understood. In this work, we use the creation relaxation algorithm (CRA) developed for atomistic modeling of high-dose irradiation in bulk materials to probe the athermal limit of saturation of GB and dislocation core regions under irradiation in fcc Ni. We find that, upon continuously subjecting a single dislocation or GB to Frenkel pair creation in the athermal limit, a local steady-state disordered defect structure is reached with excess properties that fluctuate around constant values. Case studies are given for a straight screw dislocation which elongates into a helix under irradiation and several types of low- and high-angle GBs, which exhibit coupled responses such as absorption of extrinsic dislocations, roughening, and migration. A positive correlation is found between the initial GB energy and the local steady-state GB energy under irradiation across a wide variety of GB types. Metastable GB structures with similar density in the defect core region but different initial configurations are found to converge to the same limiting structure under CRA. The mechanical responses of pristine and irradiated dislocations and GB structures are compared under an applied shear stress. Irradiated screw and edge dislocations are found to exhibit a hardening response, migrating at larger flow stresses than their pristine counterparts. Mobile GBs are found to exhibit softening or hardening responses depending on GB character. Although some GBs recover their initial pristine structures upon migration outside of the radiation zone, many GBs sustain different flow stresses corresponding to altered mobile core structures.

36 MATERIALS SCIENCE↗

TRIGGERED STAR FORMATION AND DUST AROUND MID-INFRARED-IDENTIFIED BUBBLES

We use Two Micron All Sky Survey, GLIMPSE, and MIPSGAL survey data to analyze the young stellar object (YSO) and warm dust distribution around several mid-infrared-identified bubbles. We identify YSOs using J-band to 8 {mu}m photometry and correlate their distribution relative to the photodissociation region (PDR; as traced by diffuse 8 {mu}m emission), which we assume to be associated with and surrounding an H II region. We find that only 20% of the sample H II regions appear to have a significant number of YSOs associated with their PDRs, implying that triggered star formation mechanisms acting on the boundary of the expanding H II region do not dominate in this sample. We also measure the temperature of dust inside 20 H II regions using 24 {mu}m and 70 {mu}m MIPSGAL images. In eight circularly symmetric sources, we analyze the temperature distribution and find shallower temperature gradients than predicted by an analytic model. Possible explanations of this shallow temperature gradient are a radially dependent grain-size distribution and/or non-equilibrium radiative processes.

79 ASTRONOMY AND ASTROPHYSICS↗