Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain refinement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

The improvement of cryogenic mechanical properties of Fe-12 Mn and Fe-8 Mn alloy steels through thermal/mechanical treatments

An investigation has been made to improve the low temperature mechanical properties of Fe-8Mn and Fe-12Mn-0.2 Ti alloy steels. A reversion annealing heat treatment in the two-phase (alpha + gamma) region following cold working has been identified as an effective treatment. In an Fe-12Mn-0.2Ti alloy a promising combination of low temperature (-196 C) fracture toughness and yield strength was obtained by this method. The improvement of properties was attributed to the refinement of grain size and to the introduction of a uniform distribution of retained austenite (gamma). It was also shown that an Fe-8Mn steel could be grain-refined by a purely thermal treatment because of its dislocated alpha-prime martensitic structure and absence of epsilon martensite. As a result, a significant reduction of ductile to brittle transition temperature was obtained.

Hwang, S. K.↗
DOE OSTI2021

Dynamic recrystallization of a wrought magnesium alloy: Grain size and texture maps and their application for mechanical behavior predictions

Effect of dynamic recrystallization (DRX) on the grain refinement and texture modification was studied by conducting a series of hot compression on AZ31B Mg alloy. Processing-grain size-texture maps were established as a function of temperature, strain rate, strain, and the Zener-Hollomon parameter (Z). Moreover, influence of simultaneous changes in the grain size and texture on tensile yield strength and ductility of the hot-worked Mg alloy was studied using the grain size and texture maps established. The processing-grain size map showed that the DRX grain size decreased with the increase in Z, also revealing various characteristics ranging from a grain growth, grain refinement, to a bimodal distribution of ultrafine grains and partially recrystallized grains. The effect of twinning on the grain refinement was also evident at high Z conditions. The processing-texture map revealed that the initial fiber texture was altered significantly to a shear, off-normal, or extension-twin texture with the increase in Z. The Schmid-factor maps were calculated to identify a dominant deformation mode during a subsequent tensile deformation of the hot-worked samples. Finally, a corresponding Hall-Petch relationship for each dominant deformation mode was used to establish tensile yield-strength maps, which agree well with the measured data.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of heat treatment on the microstructure of medium burn-up U-Mo monolithic fuel foils

Using scanning electron microscopy (SEM), this study evaluates the microstructure evolution of U-Mo fuel foils made with and without heat treatment at medium burn-up (of approximately 5 x 10 21 f/cm 3 ). The impact of annealing treatments on critical microstructural properties of the U-Mo fuel foils, including porosity, grain structure, Mo homogeneity, and fuel interaction with the Zr interlayer, was examined using large area lift outs (LALOs). The heat-treated specimens presented less grain refining at these burnups when compared to the un-heated specimens. Grain refinement was associated with porosities and fission products precipitation. Heat treatment can reduce fuel swelling during irradiation. Chemical inhomogeneity (Mo banding) was found to persist in the un-heated samples but was not present in the heat-treated samples. Thus, heat-treated U-Mo foils allows for more predictable fuel behavior under irradiation with respect to un-heated foils. The U-Mo and Zr interaction layer appears to be thicker and more continuous in the heat-treated sample which has been associated with stronger interface integrity during irradiation, as also observed in previous studies. These observations may indicate an overall improved performance of heat-treated fuel foil in a reactor. Further, the effect of local burn-up on grain size/refinement and porosities in each LALO specimen, sampled from different positions in the fuel foil, was difficult to analyze due to the large standard deviation of these parameters. Finally, evidence of grain refinement by polygonization may be present in these specimens.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1977

Containerless processing of beryllium

Melting and solidification of a beryllium alloy containing 1.5% BeO by weight in the weightless environment of space has produced cast beryllium with a relatively uniform dispersion of BeO throughout. Examination of the cast material shows that it is coarse grained, although the BeO is not heavily agglomerated in the flight specimen. Ground based comparison experiments show extreme agglomeration and segregation of BeO, resulting in large zones which are practically free of the oxide. Several postulated hypotheses for the failure to grain refine the beryllium are formulated. These are: (1) spherodization of the BeO particles during specimen preparation and during the molten phase of the experiment; (2) loss of nucleation potency through aging in the molten phase; and (3) inability of BeO to act as a grain refiner for beryllium. Further investigation with non spherodized particles and shorter dwell times molten may delineate which of these hypotheses are valid. The results of this flight experiment indicate that the weightless environment of space is an important asset in conducting research to find grain refiners for beryllium and other metals for which cast dispersions of grain refining agents cannot be prepared terrestrially due to gravitationally driven settling and agglomeration.

Wouch, G.↗
DOE OSTI2026

Understanding the effect of friction stir processing on electrical steel: Microstructural changes and mechanical transformations

Raising Si beyond 3.5 wt% reduces core loss but embrittles electrical steels, constraining processing and application. Here we assess friction stir processing (FSP) as a solid‑state route to enable Fe–4.0 wt% Si with improved mechanical performance. Temperature‑controlled FSP with a PcBN tool produced a defect‑free processed zone. SEM/EBSD revealed dynamic recrystallization and grain refinement from an average 110 μm in the base material to ∼20 μm in the processed region, with ∼ 80% of grains < 40 μm and a reduction in high‑angle boundary fraction to ∼65% (vs >85% in the base). Comparative mechanical property analysis shows a moderate increase in yield strength in FSP samples relative to the base material, with a significant improvement in ductility (∼35–50%). Post‑fracture EBSD identified 60° twin boundaries in the base while sub-grain formation with elevated KAM in the FSP sample. Fractography revealed a shift from quasi‑cleavage in the Base-faceted planes with river patterns, steps, and occasional secondary cracks—to ductile micro void coalescence after FSP. Following FSP, the material retains soft‑magnetic behavior, with modest shifts in saturation magnetization consistent with grain refinement and stored strain, accompanied by a clear gain in formability. These results indicate that FSP provides a viable route to deploy higher‑Si electrical steels with concurrent gains in strength and ductility.

Electrical steel↗
DOE OSTI2022

Effect of loading path on grain misorientation and geometrically necessary dislocation density in polycrystalline aluminum under reciprocating shear

Solid phase processing (SPP) is a promising alloy fabrication technique to produce fine and homogeneous grain structures for high-performance alloys. However, there is very limited modeling capability to understand and predict the grain refinement during SPP. In this work, the crystal plasticity theory was used to study elastic-plastic deformation in polycrystalline aluminums under large shear deformation. Two approaches, kernel averaged misorientation (KAM) and grain reference orientation deviation (GROD), were used to assess the grain misorientations. The geometrically necessary dislocation (GND) density was computed with the plastic strain rate. The deformation simulations were carried out under two loading conditions to investigate the effect of loading paths on the evolutions of grain misorientation and GND density. The results show that the regions with high misorientation and GND density first appear near grain boundaries. These regions then extend toward interior grains. The loading path affects dislocation system activation and dislocation recovery, hence dislocation evolution and misorientation. In conclusion, both two- and three-dimensional simulations showed that the spatial and temporal evolutions of GROD, KAM, and GND density in are closely correlated, which indicates they all can be used as criteria of grain refinement or recrystallization.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural evolution in shear-punch tests: A comparative study of pure Cu and Cu-Cr alloy

Understanding the mechanisms behind microstructural evolution during shear deformation has been a long-standing area of interest. However, establishing a connection between microstructure, mechanical properties, and extent of shear deformation is challenging and requires refined experimental approaches. Shear-punch testing (SPT) provides a controlled method to introduce shear into small volumes of material that later can be subjected to detailed microstructural characterization. In this study, we utilize an SPT device to induce shear deformation to pure copper and a binary copper-chromium alloy. Electron backscatter diffraction and transmission electron microscopy were used to study the mechanisms of plastic deformation after SPT. Our results indicate that shear deformation of pure Cu produces a dense network of intercepting microshear bands upon sustained deformation. Twin boundaries undergo degradation into high angle grain boundaries due to simultaneous deviation from the axis-angle pair condition of 60° misorientation on [111] direction. The presence of 50% volume Cr particles in the soft Cu matrix fundamentally altered the shear deformation mechanism. Preferential deformation of the Cu matrix led to accelerated shear-induced formation of low and high angle grain boundaries, and subsequent grain refinement. Comparatively, no grain refinement occurred in pure Cu at a strain ~10 times larger (ϵ = 4.73) than that of the copper-chromium case (ϵ = 0.42). Overall, our study sheds light on the microstructural evolution during shear deformation and highlights the significant influence of particle reinforcements on the shear deformation mechanisms of metals.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure and texture evolution of friction stir lap welded dissimilar multi-aluminum stack

Here this work investigates the microstructural evolution of a dissimilar multiple-aluminum alloy stack (AA7055, AA7055, AA6022) produced by friction stir lap welding (FSLW). A through-thickness analyses of grain orientation map, grain size and distribution, strain distribution, and texture evolution by electron backscattered diffraction-based characterization technique were performed. Two different welding parameters (combination of tool rotation and traverse speed) were used to study the effects of the welding parameters on these microstructural characteristics. The study shows that higher welding speed and higher rotation speed of the FSLW tool yield finer grains. FSLW resulted in shear texture formation in the weld regions due to high welding speeds. This texture development in the nugget zone is consistent with shear deformation, and (111) pole figures show ideal shear texture components. The Stir Zone (SZ) exhibits shear texture (A/A ̅ and B/B ̅ components), consistent with other shear-assisted processes. Recrystallization mechanisms observed are CDRX in SZ and DDRX in TMAZ (Thermo-Mechanically Affected Zone). Interface analysis reveals the presence of oxide layers between different aluminum sheets, affecting joint mechanical performance. The mechanical property of the lap welded joints was presented in terms of microhardness distribution across the weld cross section. Slightly higher hardness in higher speed welding setup was observed throughout the SZ and AA6022 layer, indicating greater grain refinement and uniform grain structure distribution.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Use of friction stir processing to synthesize nanocrystalline, grain boundary segregating Fe-Ti alloys

Grain boundary segregating alloys, a class of alloys designed such that nanocrystalline grain sizes are thermodynamically stabilized by the presence of high segregation energy solutes at the grain boundaries, are typically produced through geometrically limited processing techniques such as equal channel angular extrusion or thin film sputtering. Here, this study explores the use of friction stir processing (FSP) as a novel means of studying and producing these alloys using a test system of Fe-6at%Ti. Spot FSPs with a range of processing parameter sets were produced on bulk, coarse grained bars of material and optimal parameters were identified. Microscopy identified a range of processed materials which achieved nanocrystalline grains on the order of 100 nm, delineating a critical window of processing parameters which limit heat input while inducing sufficient plastic deformation for grain refinement. The finest grained nanocrystalline Fe-Ti achieved a hardness of 7.68 GPa, a significant increase in hardness over pure Fe with a similar microstructure due to increased dislocation density from FSP as well as several strengthening mechanisms produced through the presence and segregation of Ti. These results demonstrated the feasibility of using FSP to produce nanocrystalline grain boundary segregating alloys.

Fe alloys↗
DOE OSTI2023

In situ synchrotron X-ray diffraction analysis of ultrasonically assisted microstructure refinement during laser melting process

This work investigates the effect of ultrasonic treatment (UST) on the microstructure of AA4043 alloy during laser melting process. Here, the study utilizes in situ synchrotron X-ray diffraction (SXRD) and postmortem electron backscatter diffraction (EBSD) techniques to examine the ultrasonic grain refinement mechanism. The SXRD diffraction patterns exhibit higher continuity of major diffraction rings in the UST-test pattern, indicating a more refined grain structure. The presence of new diffraction spots in the post-test diffraction pattern with UST suggests the breakdown of epitaxial growth of columnar dendrites during solidification. Thermal profiles determined by analyzing the lattice parameter evolution show a faster cooling rate with UST. The inverse pole figures and aspect ratio distribution from EBSD reveal that the UST samples exhibit a refined, more equiaxed grain structure along the weld centerline. UST sample also develops more fine-sized low angle grain boundaries (LAGBs). These features offer better hot-cracking resistance in aluminum alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Nanotwin assisted reversible formation of low angle grain boundary upon reciprocating shear load

Severe plastic deformation of metals is known to lead to superior properties that cannot be achieved by any traditional metallurgic process. Origin of the superior properties is perceived to be closely associated with grain refinement, a fundamental process during the severe plastic deformation, which is essentially the formation of new grain boundaries. However, the atomistic mechanism of grain boundary formation remains largely obscure. Here, by using in-situ transmission electron microscopy and molecular dynamic simulation, we reveal, for the first time at atomic level, the shear-induced low-angle grain boundary (LAGB) formation processes in Au nanocrystal. In this work, we discover the LAGB formation is accomplished through inward propagation of nanotwins accompanied by dislocations gliding on the twin boundaries, a nanotwin-mediated dislocation slip mechanism, which shows reversible characteristic under reciprocating shear load and is affected by the nanocrystal microstructure and orientation. Our result unveils unprecedented atomistic insights on shear driven grain refinement towards nanostructure of superior properties.

36 MATERIALS SCIENCE↗
NASA NTRS1986

Increasing the Cryogenic Toughness of Steels

Grain-refining heat treatments increase toughness without substantial strength loss. Five alloys selected for study, all at or near technological limit. Results showed clearly grain sizes of these alloys refined by such heat treatments and grain refinement results in large improvement in toughness without substantial loss in strength. Best improvements seen in HP-9-4-20 Steel, at low-strength end of technological limit, and in Maraging 200, at high-strength end. These alloys, in grain refined condition, considered for model applications in high-Reynolds-number cryogenic wind tunnels.

Rush, H. F.↗
NASA NTRS1995

The Grain Structure of Castings: Some Aspects of Modelling

The efficacy of the modelling of the solidification of castings is typically tested against observed cooling curves and the final grain structures and sizes. Without thermo solutal convection, equiaxed grain formation is promoted by introduction of heterogeneous substrates into the melt, as grain refiners. With efficient thermo solutal convection, dendrite fragments from the mushy zone can act as an intrinsic source of equiaxed grains and resort to grain refining additions is unnecessary. The mechanisms of dendrite fragmentation and transport of these fragments are briefly considered.

Hellawell, A.↗
DOE OSTI2020

Development of Mischmetal–Fe–Co–B Permanent Magnet Alloys via High-Throughput Methods

Additive manufacturing synthesis using laser engineered net shaping (LENS) is utilized in this work to rapidly print libraries of mischmetal (MM = La, Ce, Nd, and Pr) containing R 2 TM 14 B alloys (R = MM + separated Nd and TM = Fe and Co) enabling robust evaluation of physical properties over a wide composition range. High-throughput characterization of the magnetic and thermal properties are used to identify compositions for potential high-temperature, high-performance permanent magnets with reduced critical rare-earth elements. Improved Curie temperature ( T c ~ 450 °C) is obtained with substitution of Fe by Co in pseudoternary R 2 TM 14 B alloys. Furthermore, a 4-fold decrease in the Nd content can be achieved through substitution with less critical Ce- and La-rich MM, while retaining high T c . Guided by the properties of the LENS printed samples, selected compositions with and without TiC additions are synthesized via melt-spinning techniques to produce nanostructured ribbons. The maximum room temperature coercivity ( H c ) and energy product ((BH) max ) without TiC are found to be 5.8 kOe, 8.5 MGOe, respectively, while TiC additions as a grain refiner gave H c and (BH) max of 4.9 kOe, 9.8 MGOe, respectively. Structural characterization of the melt-spun ribbons shows homogeneous grain refinement with TiC additions, which leads to an increase in the energy product.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Relating Texture and Thermomechanical Processing Variables in Mg–Zn–Ca Alloys

It is well known that the strong basal texture commonly produced in magnesium alloy sheets leads to poor formability at room temperature. A sizable body of work has explored how changing the alloy composition and rolling conditions can yield more desirable textures; however important thermomechanical variables, such as the feed rate during rolling, are often not included in the literature, making it difficult to correlate how changes in processing affect the final crystallographic texture. This work explores the texture evolution and grain refinement in Mg-Zn-Ca alloys during plane strain compression (PSC) using a Gleeble thermomechanical simulator. This instrument allows for precise control and capture of the thermomechanical history of the sample. The texture and grain morphology of the compressed samples were characterized using Electron Backscatter Diffraction (EBSD). The texture results will be used to identify which alloys and processing conditions should be scaled up for future rolling studies.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Extrusion of Unhomogenized Castings of 7075 Aluminum via ShAPE

Extrusion of unhomogenized castings of 7075 aluminum (Al) alloy has been accomplished using shear assisted processing and extrusion (ShAPE). The simultaneous plastic deformation and heat generation during ShAPE rapidly fracture and dissolve interdendritic and intragranular secondary phases of Al-Zn-Mg-Cu, accomplishing homogenization in seconds rather than many hours in a furnace prior to extrusion. ShAPE thereby eliminates the energy-intensive and time-consuming homogenization step required to prepare as-cast microstructures for conventional extrusion. Concurrently, extensive grain refinement occurs due to gradient activation of dynamic recrystallization during ShAPE, which facilitates a threefold increase in extrusion speed compared to the conventional extrusion method. Evident enhancement of the mechanical properties of ShAPE+T6 samples is achieved, compared to the ASTM standard values for conventional extrusion products. The microstructural evolution pathway, involving the processes of grain refinement and secondary particle dissolution, is explained using scanning and transmission electron microscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Achieving strong and stable nanocrystalline Al alloys through compositional design

Abstract Al alloys often suffer from low mechanical strength and lack high-temperature microstructural and mechanical robustness. A series of binary and ternary nanocrystalline (NC) Al transition metal alloys with supersaturated solid solution and columnar nanograins have been recently developed by using magnetron sputtering, manifesting a new realm of mechanical properties and thermal stability. Distinct solutes cause evident differences in the phase transformations and efficiencies for grain refinement and crystalline-to-amorphous transition. Certain sputtered Al-TM alloys have shown room-temperature mechanical strengths greater than 2 GPa and outstanding thermal stability up to 400 °C. In addition, the NC Al alloys show mechanical anisotropy and tension–compression asymmetry, revealed by micromechanical tests. Through the process encapsulating various compositionally distinct systems, we attempt to illuminate the solute effects on grain refinement and properties and more importantly, tentatively unravel the design criteria for high-strength and yet thermally stable NC Al alloys. Graphic Abstract

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupled solute effects enable anomalous high-temperature strength and stability in nanotwinned Al alloys

Nanoprecipitates or grain refinement can effectively enhance the mechanical strength of Al alloys, but the room-temperature strengths of precipitation hardened and nanocrystalline Al alloys often fall below 1 GPa. Furthermore, they are largely plagued by precipitous mechanical softening at elevated temperature below 300°C, mostly due to degraded microstructural stability. Here, we report a mechanism of coupled solute effect in nanotwinned Al-Fe-Ti alloys that enables stability of nanograins up to 400°C and an unprecedented high-temperature flow stress of ~ 1.7 GPa at 300°C. The supersaturated Fe solutes in Al act as effective grain refiner, forming superstrong solid solution alloys. More importantly, empirical evidence combined with first principle calculations indicate that the Ti solutes delay the agglomeration of Fe solutes, thereby remarkably extending the temperature window for the stability of nanograins in nanotwinned Al alloys. Finally, this study highlights the opportunity to design ultrastrong and stable nanostructured alloys for potential high temperature applications via a coupled solute effect.

36 MATERIALS SCIENCE↗