Search NASA⌕ Search

SEARCH · Search NASA

Results for “HYDROGEN PLASMA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Operating characteristics of a hydrogen-argon plasma torch for supersonic combustion applications

The residence time of the combustible mixture in the combustion chamber of a scramjet engine is much less than the time normally required for complete combustion. Hydrogen and hydrocarbon fuels require an ignition source under conditions typically found in a scramjet combustor. Analytical studies indicate that the presence of hydrogen atoms should greatly reduce the ignition delay in this environment. Because hydrogen plasmas are prolific sources of hydrogen atoms, a low-power, uncooled hydrogen plasma torch has been built and tested to evaluate its potential as a possible flame holder for supersonic combustion. The torch was found to be unstable when operated on pure hydrogen; however, stable operation could be obtained by using argon as a body gas and mixing in the desired amount of hydrogen. The stability limits of the torch are delineated and its electrical and thermal behavior documented. An average torch thermal efficiency of around 88 percent is demonstrated.

Barbi, E.↗
NASA NTRS1971

Thermodynamic properties of hydrogen-helium plasmas

The thermodynamic properties of an atomic hydrogen-helium plasma are calculated and tabulated for temperatures from 10,000 to 100,000 K as a function of the mass fraction ratio of atomic hydrogen. The tabulation is for densities from 10 to the minus 10th power to 10 to the minus 6th power gm/cu cm and for hydrogen mass fraction ratios of 0, 0.333, 0.600, 0.800, and 1.0, which correspond to pure helium, 50 percent hydrogen per unit volume, 75 percent hydrogen per unit volume, 89 percent hydrogen per unit volume, and pure hydrogen plasmas, respectively. From an appended computer program, calculations can be made at other densities and mass fractions. The program output agrees well with previous thermodynamic property calculations for limiting cases of pure hydrogen and pure helium plasmas.

Nelson, H. F.↗
NASA NTRS1992

Innovative techniques for the production of energetic radicals for lunar processing including cold plasma processing of local planetary ores

Hydrogen reduction of ilmenite has been studied by a number of investigators as a potential means for recovery of oxygen from lunar soil. Interest in this process has always rested with the simplicity of the flow diagram and the utilization of established technology. Effective utilization of hydrogen in the reduction process at temperatures of 1200 C and below has always been disappointing and, as such, has led other investigators to focus attention on other systems. Effective utilization of hydrogen in the reduction of ilmenite can be significantly enhanced in the presence of a non-equilibrium hydrogen plasma. Ilmenite at solid specimen temperatures of 600 C to 970 C were reacted in a hydrogen plasma. Those experiments revealed that hydrogen utilization can be significantly enhanced. At a specimen temperature of 850 C the fraction of H2 reacted was 24 percent compared to the 7 percent theoretical limit calculated with thermodynamic theory for the same temperature. An added advantage for a hydrogen plasma involves further reduction of TiO2. Reduction of the iron oxide in ilmenite yields TiO2 and metallic iron as by products. Titanium forms a number of oxides including TiO, Ti2O3, Ti3O5 and the Magneli oxides (Ti4O7 to Ti50O99). In conventional processing of ilmenite with hydrogen it is possible to reduce TiO2 to Ti7O13 within approximately an hour, but with poor utilization of hydrogen on the order of one mole of H2 per thousand. In the cold or non-equilibrium plasma TiO2 can be rapidly reduced to Ti2O3 with hydrogen utilization exceeding 10 percent. Based on design considerations of the plasma reactor greater utilization of the hydrogen in the reduction of TiO2 is possible.

Bullard, D.↗
NASA NTRS1972

Thermodynamic properties of hydrogen-helium plasmas.

Calculation of the thermodynamic properties of an atomic hydrogen-helium plasma for postulated conditions present in a stagnation shock layer of a spacecraft entering the atmosphere of Jupiter. These properties can be used to evaluate transport properties, to calculate convective heating, and to investigate nonequilibrium behavior. The calculations have been made for temperatures from 10,000 to 100,000 K, densities of 10 to the minus 7th and .00001 g cu cm, and three plasma compositions: pure hydrogen, 50% hydrogen/50% helium, and pure helium. The shock layer plasma consists of electrons, protons, atomic hydrogen, atomic helium, singly ionized helium, and doubly atomized helium. The thermodynamic properties which have been investigated are: pressure, average molecular weight, internal energy, enthalpy, entropy, specific heat, and isentropic speed of sound. A consistent model was used for the reduction of the ionization potential in the calculation of the partition functions.

Nelson, H. F.↗
NASA NTRS1987

Design and evaluation of a new injector configuration for supersonic combustion

Ignition and flameholding behavior data are presented from experiments with a novel scramjet injector configuration consisting of five small upstream pilot fuel injectors, a rearward-facing step, and three primary fuel injectors downstream of the step; all injection is perpendicular to the Mach 2 airflow, and the ignition source is located in the recirculation region downstream of the step. The design attempts to minimize the amount of igniter energy required for ignition, but without introduction of the large losses associated with bluff bodies. Argon plasma, argon-hydrogen plasma, pyrophoric silane/hydrogen, and surface-discharge ignition sources are tested. The injector is found to be able to hold flames at 1400 R total temperatures without the use of large bluff bodies; the argon-hydrogen plasma was the most effective igniter.

Wagner, Timothy C.↗
NASA NTRS1995

Effects of Surface Treatments on Secondary Electron Emission from CVD Diamond Films

Secondary electron emission (SEE) properties of polycrystalline diamond films grown by chemical vapor deposition (CVD) were measured. The total secondary yield (sigma) from as-grown samples was observed to be as high as 20 at room temperature and 48 while heating at 700 K in vacuum. Electron-beam-activated, alkali-terminated diamond films have shown stable values of sigma as high as 60 when coated with CsI and similarly high values when coated with other alkali halides. Diamond coated with BaF2 had a stable sigma of 6, but no enhancement of the SEE properties was observed with coatings of Ti or Au. Hydrogen was identified to give rise to this effect in as-grown films. However, electron beam exposure led to a reduction in sigma values as low as 2. Exposure to a molecular hydrogen environment restored sigma to its original value after degradation, and enabled stable secondary emission during electron beam exposure. Atomic hydrogen and hydrogen plasma treatments were performed on diamond/Mo samples in an attempt to increase the near-surface hydrogen concentration which might lead to increased stability in the secondary emission. Raman scattering analysis, scanning electron microscopy, and Auger electron spectroscopy (AES) confirmed that hydrogen plasma and atomic hydrogen treatments improved the quality of the CVD diamond significantly. Elastic recoil detection (ERD) showed that heating as-grown diamond targets to 7OO K, which was correlated with an increase in sigma, removed contaminants from the surface but did not drive hydrogen from the diamond bulk. ERD showed that the hydrogen plasma treatment produced an increase in the hydrogen concentration in the near-surface region which did not decrease while heating in vacuum at 700 K, but no improvement in the SEE properties was observed.

Mearini, G. T.↗
NASA NTRS2010

NASA Tech Briefs, September 2010

Topics covered include: Instrument for Measuring Thermal Conductivity of Materials at Low Temperatures; Multi-Axis Accelerometer Calibration System; Pupil Alignment Measuring Technique and Alignment Reference for Instruments or Optical Systems; Autonomous System for Monitoring the Integrity of Composite Fan Housings; A Safe, Self-Calibrating, Wireless System for Measuring Volume of Any Fuel at Non-Horizontal Orientation; Adaptation of the Camera Link Interface for Flight-Instrument Applications; High-Performance CCSDS Encapsulation Service Implementation in FPGA; High-Performance CCSDS AOS Protocol Implementation in FPGA; Advanced Flip Chips in Extreme Temperature Environments; Diffuse-Illumination Systems for Growing Plants; Microwave Plasma Hydrogen Recovery System; Producing Hydrogen by Plasma Pyrolysis of Methane; Self-Deployable Membrane Structures; Reactivation of a Tin-Oxide-Containing Catalys; Functionalization of Single-Wall Carbon Nanotubes by Photo-Oxidation; Miniature Piezoelectric Macro-Mass Balance; Acoustic Liner for Turbomachinery Applications; Metering Gas Strut for Separating Rocket Stages; Large-Flow-Area Flow-Selective Liquid/Gas Separator; Counterflowing Jet Subsystem Design; Water Tank with Capillary Air/Liquid Separation; True Shear Parallel Plate Viscometer; Focusing Diffraction Grating Element with Aberration Control; Universal Millimeter-Wave Radar Front End; Mode Selection for a Single-Frequency Fiber Laser; Qualification and Selection of Flight Diode Lasers for Space Applications; Plenoptic Imager for Automated Surface Navigation; Maglev Facility for Simulating Variable Gravity; Hybrid AlGaN-SiC Avalanche Photodiode for Deep-UV Photon Detection; High-Speed Operation of Interband Cascade Lasers; 3D GeoWall Analysis System for Shuttle External Tank Foreign Object Debris Events; Charge-Spot Model for Electrostatic Forces in Simulation of Fine Particulates; Hidden Statistics Approach to Quantum Simulations; Reconstituted Three-Dimensional Interactive Imaging; Determining Atmospheric-Density Profile of Titan; Digital Microfluidics Sample Analyzer; Radiation Protection Using Carbon Nanotube Derivatives; Process to Selectively Distinguish Viable from Non-Viable Bacterial Cells; and TEAMS Model Analyzer.

Source record↗
NASA NTRS1985

Measurement of energy distribution in flowing hydrogen microwave plasmas

An electrothermal propulsion concept utilizing a microwave plasma system as the mechanism to convert electromagnetic energy into kinetic energy of a flowing gas is investigated. A calorimetry system enclosing a microwave plasma system has been developed to accurately measure the energy inputs and outputs of the microwave plasma system. The rate of energy transferred to the gas can be determined to within + or - 1.8 W from an energy balance around the microwave plasma system. The percentage of the power absorbed by the microwave plasma system transferred to the hydrogen gas as it flows through the system is found to increase with the increasing flow rate, to decrease with the increasing pressure, and to be independent of the absorbed power. An upper bound for the hydrogen gas temperature is estimated from the energy content, heat capacity, and flow rate of the gas stream. A lower bound for an overall heat-transfer coefficient is then calculated, characterizing the energy loss from the hydrogen gas stream to the air cooling of the plasma discharge tube wall. The heat-transfer coefficient is found to increase with the increasing flow rate and pressure and to be independent of the absorbed power. This result indicates that a convective-type mechanism is responsible for the energy transfer.

Chapman, R.↗
NASA NTRS1978

Radiative cooling in shock-heated hydrogen-helium plasmas

Axial and off-axis radiative cooling of cylindrical shock-heated hydrogen-helium plasmas is investigated theoretically and experimentally. The coupled fluid dynamic-radiative transfer equations are solved by a combination of approximation techniques aimed at simplifying the computation of the flux divergence term, namely, the quasi-isothermal approximation and the exponential approximation developed for the solid angle integration. The accuracy of the approximation schemes has been assessed and found acceptable for applying the methods to the rapid computation of the radiatively coupled flow problem. Radiative cooling experiments were conducted in a 6-inch annular arc accelerator shock tube (ANAA) for an initial pressure of 1 torr and shock speeds from 35 to 45 Km/sec. The results indicate that the lateral cooling is small compared with the axial cooling, and that better agreement is achieved between the data and the theoretical results by inclusion of the lateral temperature gradient.

Poon, P. T. Y.↗
NASA NTRS1993

Determining electron temperature and density in a hydrogen microwave plasma

A three-temperature thermo-chemical model is developed for analyzing the chemical composition and energy states of a hydrogen microwave plasma used for studying diamond deposition. The chemical and energy exchange rate coefficients are determined from cross section data, assuming Maxwellian velocity distributions for electrons. The model is reduced to a zero-dimensional problem to solve for the electron temperature and ion mole fraction, using measured vibrational and rotational temperatures. The calculations indicate that the electron temperature may be determined to within a few percent error even though the uncertainty in dissociation fraction is many times larger.

Scott, Carl D.↗
NASA NTRS1974

Plasma tests of sprayed coatings for rocket thrust chambers

Several plasma-sprayed coating systems were evaluated for structural stability in hydrogen plasma and in oxygen plasma mixed with hydrogen plasma. The principal test heat flux was 15 Btu per inch squared seconds. The system consisted of a number of thin 0.002 to 0.020 in. layers of metal oxides and/or metals. The principal materials included are molybdenum nichrome, alumina, and zirconia. The study identifies important factors in coating system fabrication and describes the durability of the coating systems in the test environments. Values of effective thermal conductivity for some of the systems are indicated.

Curren, A. N.↗
NASA NTRS1976

Equilibrium and nonequilibrium electron density measurements in transient shock-heated hydrogen-helium plasmas

In the NASA planetary program, atmospheric entry probe missions to Jupiter, Saturn, and Uranus are potential programs now being planned for the 1980's. The work reported in this paper is concerned with predicting the electron density, and resulting radiative emission from the shock layer which must be accommodated by the entry probe heatshield. Within the hydrogen-helium plasma surrounding the forward heatshield, there are regions of near thermochemical equilibrium whose properties are predictable - however, there are uncertainties in these electron density calculations necessitating further measurements by H-beta line broadening and holographic interferometer fringe shift as reported here. There is good agreement between the results obtained from the holographic measurements and the spectroscopic measurements which lends confidence to each of the two completely independent diagnostic techniques. The equilibrium electron density determined from the experimental measurements is somewhat higher than that predicted.

Livingston, F. R.↗
NASA NTRS2011

Optimization of Indium Bump Morphology for Improved Flip Chip Devices

Flip-chip hybridization, also known as bump bonding, is a packaging technique for microelectronic devices that directly connects an active element or detector to a substrate readout face-to-face, eliminating the need for wire bonding. In order to make conductive links between the two parts, a solder material is used between the bond pads on each side. Solder bumps, composed of indium metal, are typically deposited by thermal evaporation onto the active regions of the device and substrate. While indium bump technology has been a part of the electronic interconnect process field for many years and has been extensively employed in the infrared imager industry, obtaining a reliable, high-yield process for high-density patterns of bumps can be quite difficult. Under the right conditions, a moderate hydrogen plasma exposure can raise the temperature of the indium bump to the point where it can flow. This flow can result in a desirable shape where indium will efficiently wet the metal contact pad to provide good electrical contact to the underlying readout or imager circuit. However, it is extremely important to carefully control this process as the intensity of the hydrogen plasma treatment dramatically affects the indium bump morphology. To ensure the fine-tuning of this reflow process, it is necessary to have realtime feedback on the status of the bumps. With an appropriately placed viewport in a plasma chamber, one can image a small field (a square of approximately 5 millimeters on each side) of the bumps (10-20 microns in size) during the hydrogen plasma reflow process. By monitoring the shape of the bumps in real time using a video camera mounted to a telescoping 12 magnifying zoom lens and associated optical elements, an engineer can precisely determine when the reflow of the bumps has occurred, and can shut off the plasma before evaporation or de-wetting takes place.

Jones, Todd J.↗
NASA NTRS2012

Method to Improve Indium Bump Bonding via Indium Oxide Removal Using a Multi-Step Plasma Process

A process for removing indium oxide from indium bumps in a flip-chip structure to reduce contact resistance, by a multi-step plasma treatment. A first plasma treatment of the indium bumps with an argon, methane and hydrogen plasma reduces indium oxide, and a second plasma treatment with an argon and hydrogen plasma removes residual organics. The multi-step plasma process for removing indium oxide from the indium bumps is more effective in reducing the oxide, and yet does not require the use of halogens, does not change the bump morphology, does not attack the bond pad material or under-bump metallization layers, and creates no new mechanisms for open circuits.

Greer, H. Frank↗
NASA NTRS1995

Plasma processing of interstellar PAHs into solar system kerogen

Processes resulting in the formation of hydrocarbons of carbonaceous chondrites and the identity of the interstellar molecular precursors involved are an objective of investigations into the origin of the solar system and perhaps even life on earth. We have combined the resources and experience of an astronomer and physicists doing laboratory simulations with those of a chemical expert in the analysis of meteoritic hydrocarbons, in a project that investigated the conversion of polycyclic aromatic hydrocarbons (PAHs) formed in stellar atmospheres into alkanes found in meteorites. Plasma hydrogenation has been found in the University of Alabama at Birmingham Astrophysics Laboratory to produce from the precursor PAH naphthalene, a new material having an IR absorption spectrum (Lee, W. and Wdowiak, T.J., Astrophys. J. 417, L49-L51, 1993) remarkably similar to that obtained at Arizona State University of the benzene-methanol extract of the Murchison meteorite (Cronin, J.R. and Pizzarello, S., Geochim. Cosmochim. Acta 54, 2859-2868, 1990). There are astrophysical and meteoritic arguments for PAH species from extra-solar sources being incorporated into the solar nebula, where plasma hydrogenation is highly plausible. Conversion of PAHs into alkanes could also have occurred in the interstellar medium. The synthesis of laboratory analogs of meteoritic hydrocarbons through plasma hydrogenation of PAH species is underway, as is chemical analysis of those analogs. The objective is to clarify this heretofore uninvestigated process and to understand its role during the origin of the solar system as a mechanism of production of hydrocarbon species now found in meteorites. Results have been obtained in the form of time-of-flight spectroscopy and chemical analysis of the lab analog prepared from naphthalene.

NASA Discipline Exobiology↗
NASA NTRS1978

Effect of anode-cathode geometry on performance of the HIP-1 hot ion plasma

Hot-ion hydrogen plasma experiments were conducted in the NASA Lewis HIP-1 magnetic mirror facility to determine how the ion temperature was influenced by the axial position of the cathode tips relative to the anodes. A steady-state EXB plasma was formed by applying a strong radially inward dc electric field near the throats of the magnetic mirrors. The dc electric field was created between hollow cathode rods inside hollow anode cylinders, both concentric with the magnetic axis. The highest ion temperatures, 900 eV, were attained when the tip of each cathode was in the same plane as the end of its anode. These temperatures were reached with 22 kV applied to the electrodes in a field of 1.1 tesla. Scaling relations were empirically determined for ion temperature and the product of ion density and neutral particle density as a function of cathode voltage, discharge current, and electrode positions. Plasma discharge current vs voltage (I-V) characteristics were determined.

Lauver, M. R.↗
NASA NTRS1973

Measurement of plasma temperature and density using laser absorption

A laser radiation absorption technique, suitable for temporal measurement of the electron density, the temperature, or a simultaneous determination of both, in an LTE plasma, is discussed. The theoretical calculation of the absorption coefficient for a hydrogen plasma is outlined; some results are presented for visible wavelengths. Measurements of electron density and temperature are presented and shown to be in good agreement with those values obtained by other methods. Finally, the possible use of the argon ion laser for simultaneous electron density and temperature measurement is discussed, and the theoretical curves necessary for its application to hydrogen plasma diagnostics are shown.

Billman, K. W.↗
NASA NTRS1985

Plasma deposited hydrogenated carbon on GaAs and InP

The properties of diamond like carbon films grown by RF flow discharge 30 kHz plasma using methane are reported. The Cis XPS line shape of films showed localized hybrid carbon bonds as low as 40 to as high as 95 percent. Infrared spectroscopy and N(15) nuclear reaction profiling data indicated 35 to 42 percent hydrogen, depending inversely on deposition temperature. The deposition rate of films on Si falls off exponentially with substrate temperature, and nucleation does not occur above 200 C on GaAs and InP. Optical data of the films showed bandgap values of 2.0 to 2.4 eV increasing monotonically with CH4 flow rate.

Warner, J. D.↗