Search NASA⌕ Search

SEARCH · Search NASA

Results for “High aspect ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Wind-tunnel investigation of longitudinal and lateral-directional stability and control characteristics of a 0.237-scale model of a remotely piloted research vehicle with a thick, high-aspect-ratio supercritical wing

A 0.237-scale model of a remotely piloted research vehicle equipped with a thick, high-aspect-ratio supercritical wing was tested in the Langley 8-foot transonic tunnel to provide experimental data for a prediction of the static stability and control characteristics of the research vehicle as well as to provide an estimate of vehicle flight characteristics for a computer simulation program used in the planning and execution of specific flight-research mission. Data were obtained at a Reynolds number of 16.5 x 10 to the 6th power per meter for Mach numbers up to 0.92. The results indicate regions of longitudinal instability; however, an adequate margin of longitudinal stability exists at a selected cruise condition. Satisfactory effectiveness of pitch, roll, and yaw control was also demonstrated.

Byrdsong, T. A.↗
NASA NTRS1996

Validation of High Aspect Ratio Cooling in a 89 kN (20,000 lb(sub f)) Thrust Combustion Chamber

In order to validate the benefits of high aspect ratio cooling channels in a large scale rocket combustion chamber, a high pressure, 89 kN (20,000 lbf) thrust, contoured combustion chamber was tested in the NASA Lewis Research Center Rocket Engine Test Facility. The combustion chamber was tested at chamber pressures from 5.5 to 11.0 MPa (800-1600 psia). The propellants were gaseous hydrogen and liquid oxygen at a nominal mixture ratio of six, and liquid hydrogen was used as the coolant. The combustion chamber was extensively instrumented with 30 backside skin thermocouples, 9 coolant channel rib thermocouples, and 10 coolant channel pressure taps. A total of 29 thermal cycles, each with one second of steady state combustion, were completed on the chamber. For 25 thermal cycles, the coolant mass flow rate was equal to the fuel mass flow rate. During the remaining four thermal cycles, the coolant mass flow rate was progressively reduced by 5, 6, 11, and 20 percent. Computer analysis agreed with coolant channel rib thermocouples within an average of 9 percent and with coolant channel pressure drops within an average of 20 percent. Hot-gas-side wall temperatures of the chamber showed up to 25 percent reduction, in the throat region, over that of a conventionally cooled combustion chamber. Reducing coolant mass flow yielded a reduction of up to 27 percent of the coolant pressure drop from that of a full flow case, while still maintaining up to a 13 percent reduction in a hot-gas-side wall temperature from that of a conventionally cooled combustion chamber.

Wadel, Mary F.↗
NASA NTRS1947

An Investigation of the Effects of Sweep on the Characteristics of a High-Aspect-Ratio Wing in the Langley 8-Foot High-Speed Tunnel

An untwisted wing, which when unswept has an NACA 65-210 section, an aspect ratio of 9.0 and a taper ration of 2.5:1.0, has been tested with no sweep, and 30 deg and 45 deg of sweepback and sweepforward in conjunction with a typical fuselage at Mach numbers from 0.60 to 0.96 at angles of attack generally between -2 deg and 10 deg in the Langley 8-foot high-speed tunnel. Sweep was obtained by rotating the wing semispans about a point in the plane of symmetry. The normal-force, pitching-moment, profile-drag, and loading characteristics for the wings have been obtained from pressure measurements and wake surveys. The results indicate that the wings with +/-30 deg of sweep experienced the severe changes in characteristics associated with the presence of a shock at higher Mach numbers then did the wing without sweep. The differences between the Mach numbers at which the changes occurred for the wings with +/-30 deg sweep and no sweep were generally slightly less than the factor 1/cosDelta(sub r) times the Mach numbers at which the changes occurred for the unswept wing, Delta(sub r) being the sweep angle. The wings with +/-45 deg of sweep did not experience the changes in the characteristics associated with the presence of shock at an angle of attack of 2 deg at Mach numbers up to the highest test value. The magnitudes of changes in the normal-force and pitching-moment coefficients that occurred were less for the wing with 30 deg of sweep than for the unswept wing. The use of sweepforward was superior to sweepback in delaying and reducing the changes in the normal-force coefficients, but was inferior in delaying and reducing the changes in the profile-drag coefficients. Increasing the Mach number to the highest test values had little effect on the positions of the center of loads on the various configurations for the probable design load conditions.

Whitcomb, Richard T.↗
NASA NTRS1994

Visualization of Secondary Flow Development in High Aspect Ratio Channels with Curvature

The results of an experimental project to visually examine the secondary flow structure that develops in curved, high aspect-ratio rectangular channels are presented. The results provide insight into the fluid dynamics within high aspect ratio channels. A water flow test rig constructed out of plexiglass, with an adjustable aspect ratio, was used for these experiments. Results were obtained for a channel geometry with a hydraulic diameter of 10.6 mm (0.417 in.), an aspect ratio of 5.0, and a hydraulic radius to curvature radius ratio of 0.0417. Flow conditions were varied to achieve Reynolds numbers up to 5,100. A new particle imaging velocimetry technique was developed which could resolve velocity information from particles entering and leaving the field of view. Time averaged secondary flow velocity vectors, obtained using this velocimetry technique, are presented for 30 degrees, 60 degrees, and 90 degrees into a 180 degrees bend and at a Reynolds number of 5,100. The secondary flow results suggest the coexistence of both the classical curvature induced vortex pair flow structure and the eddies seen in straight turbulent channel flow.

Meyer, Michael L.↗
NASA NTRS1986

Divergence study of a high-aspect ratio, forward-swept wing

An experimental wind-tunnel study to determine the divergence characteristics of a high-aspect ratio, forward-swept wing has been conducted in the NASA Langley Research Center (LaRC) Transonic Dynamics Tunnel (TDT). The rectangular wing used for this study had a panel aspect ratio of 9.16 (lambda = 0 deg.) and the sweep angle could be set at lambda = 0 deg., -15 deg., -30 deg., -45 deg., or -60 deg. A rectangular wing tip shape was tested at each of these sweep angles. In addition, a tip shape parallel to the freestream flow was tested for a wing sweep angle of lambda = -45 deg. The root of the wing was cantilever mounted to the wall of the wind tunnel. Divergence conditions were measured at M = 0.4 for each sweep angle and tip configuration tested. Subcritical response techniques were used to extrapolate to the divergence conditions during the wind-tunnel test. The primary objective of this test was to obtain data which could be used to verify for this configuration the divergence prediction capability of an aeroelastic analysis code. Subsonic lifting surface theory (kernel function) aerodynamics are utilized by this particular code. The analytical predictions of divergence were found to be significantly conservative at all forward sweep angles. At lambda = -45 deg., the analysis was 14 percent conservative. The effect of the two tip shapes on the divergence dynamic pressure was predicted accurately by the analysis. The divergence condition for the tip shape parallel to the flow occurred at a dynamic pressure 14 percent higher than the divergence condition with a rectangular tip shape.

Cole, S. R.↗
NASA NTRS2002

Etching of Silicon in HBr Plasmas for High Aspect Ratio Features

Etching in semiconductor processing typically involves using halides because of the relatively fast rates. Bromine containing plasmas can generate high aspect ratio trenches, desirable for DRAM and MEMS applications, with relatively straight sidewalk We present scanning electron microscope images for silicon-etched trenches in a HBr plasma. Using a feature profile simulation, we show that the removal yield parameter, or number of neutrals removed per incident ion due to all processes (sputtering, spontaneous desorption, etc.), dictates the profile shape. We find that the profile becomes pinched off when the removal yield is a constant, with a maximum aspect ratio (AR) of about 5 to 1 (depth to height). When the removal yield decreases with increasing ion angle, the etch rate increases at the comers and the trench bottom broadens. The profiles have ARs of over 9:1 for yields that vary with ion angle. To match the experimentally observed etched time of 250 s for an AR of 9:1 with a trench width of 0.135 microns, we find that the neutral flux must be 3.336 x 10(exp 17)sq cm/s.

Hwang, Helen H.↗
NASA NTRS2020

Fiber-Optic Strain-Based Deflection and Twist Sensing for a High-Aspect-Ratio Swept Wing

Designs of aircraft structures have been moving toward leaner, lightweight designs for increased fuel efficiency. The Passive Aeroelastic Tailored (PAT) wing developed under the NASA Advanced Air Transport Technology (AATT) project is an example of a swept-wing design with high aspect ratio that incorporates lightweight highly-flexible tailored composite construction. The passive aeroelastic tailored structural design has explored the design space to enable aeroelastically tailored wing structures to increase aspect ratios (from 9 to 14) and ultimately reduce weight by 20 percent to 25 percent without impacting aeroelastic performance. To further study the aeroelastic performance of such a wing, the NASA Armstrong Flight Research Center (AFRC) (Edwards, California) has developed efficient real-time structural algorithms that are used in conjunction with a fiber-optic measurement system for lightweight vehicle applications. The AFRC Fiber Optic Sensing System (FOSS) provides up to 8,000 distributed surface strain measurements at one-half-inch increments and can be used to estimate a variety of structural parameters such as shape and load. This report discusses the implementation of strain-based displacement and twist-sensing techniques applied to the PAT wing test article tested at the NASA AFRC Flight Loads Laboratory. Empirical FOSS strain data are collected under varying loading conditions. Strain data are processed with the displacement and twist-sensing algorithms and independently verified by comparison to conventional ground-based instrumentation.

Pena, Francisco↗
NASA NTRS1978

Effects of wing leading-edge deflection on the low-speed aerodynamic characteristics of a low-aspect-ratio highly swept arrow-wing configuration

Wing leading-edge deflection effects on the low-speed aerodynamic characteristics of a low-aspect-ratio highly swept arrow-wing configuration were determined. Static force tests were conducted in a V/STOL tunnel at a Reynolds number of about 2.5 x 1 million for an angle-of-attack range from -10 deg to 17 deg and an angle-of-sideslip range from -5 deg to 5 deg. Limited flow visualization studies were also conducted in order to provide a qualitative assessment of leading-edge upwash characteristics.

Coe, P. L., Jr.↗
NASA NTRS1978

Control-surface hinge-moment calculations for a high-aspect-ratio supercritical wing

The hinge moments, at selected flight conditions, resulting from deflecting two trailing edge control surfaces (one inboard and one midspan) on a high aspect ratio, swept, fuel conservative wing with a supercritical airfoil are estimated. Hinge moment results obtained from procedures which employ a recently developed transonic analysis are given. In this procedure a three dimensional inviscid transonic aerodynamics computer program is combined with a two dimensional turbulent boundary layer program in order to obtain an interacted solution. These results indicate that trends of the estimated hinge moment as a function of deflection angle are similar to those from experimental hinge moment measurements made on wind tunnel models with swept supercritical wings tested at similar values of free stream Mach number and angle of attack.

Perry, B., III↗
NASA NTRS1986

Divergence study of a high-aspect ratio, forward-swept wing

A study has been conducted in the NASA-Langley Transonic Dynamics wind tunnel to determine the divergence characteristics of a high aspect ratio forward swept wing of rectangular planform, for sweep angles of zero, -15, -30, -45, and -60 deg. In addition to a rectangular wingtip, a tip whose geometry lay parallel with the freestream flow was tested at a sweep angle of -45 deg. The primary objective was to obtain data that could be used to verify the divergence prediction capabilities of an aeroelastic analysis code employing kernel function aerodynamics. The analytical predictions of convergence were found to be conservative for all forward sweep angles, and the effect of the two tip shapes on divergence dynamic pressure were accurately predicted.

Cole, S. R.↗
NASA NTRS2015

Noise Measurements of High Aspect Ratio Distributed Exhaust Systems

This paper covers far-field acoustic measurements of a family of rectangular nozzles with aspect ratio 8, in the high subsonic flow regime. Several variations of nozzle geometry, commonly proposed for embedded exhaust systems, are explored, including bevels, slants, single broad chevrons and notches, and internal septae. Far-field acoustic results, presented previously for the simple rectangular nozzle, showed that increasing aspect ratio increases the high frequency noise, especially directed in the plane containing the minor axis of the nozzle. Detailed changes to the nozzle geometry generally made little difference in the noise, and the differences were greatest at low speed. Having an extended lip on one broad side ('bevel') did produce up to 3dB more noise in all directions, while extending the lip on the narrow side ('slant') produced up to 2dB more noise, primarily on the side with the extension. Adding a single, non-intrusive chevron, made no significant change to the noise, while inverting the chevron ('notch') produced up to 2dB increase in the noise. Having internal walls ('septae') within the nozzle, such as would be required for structural support or when multiple fan ducts are aggregated, reduced the noise of the rectangular jet, but could produce a highly directional shedding tone from the septae trailing edges. Finally, a nozzle with both septae and a beveled nozzle, representative of the exhaust system envisioned for a distributed propulsion aircraft with a common rectangular duct, produced almost as much noise as the beveled nozzle, with the septae not contributing much reduction in noise.

Noise↗
NASA NTRS2015

Noise Measurements of High Aspect Ratio Distributed Exhaust Systems

This paper covers far-field acoustic measurements of a family of rectangular nozzles with aspect ratio 8, in the high subsonic flow regime. Several variations of nozzle geometry, commonly found in embedded exhaust systems, are explored, including bevels, slants, single broad chevrons and notches, and internal septae. Far-field acoustic results, presented previously for the simple rectangular nozzle, showed that increasing aspect ratio increases the high frequency noise, especially directed in the plane containing the minor axis of the nozzle. Detailed changes to the nozzle geometry generally made little difference in the noise, and the differences were greatest at low speed. Having an extended lip on one broad side (bevel) did produce up to 3 decibels more noise in all directions, while extending the lip on the narrow side (slant) produced up to 2 decibels more noise, primarily on the side with the extension. Adding a single, non-intrusive chevron, made no significant change to the noise, while inverting the chevron (notch) produced up to 2decibels increase in the noise. Having internal walls (septae) within the nozzle, such as would be required for structural support or when multiple fan ducts are aggregated, reduced the noise of the rectangular jet, but could produce a highly directional shedding tone from the septae trailing edges. Finally, a nozzle with both septae and a beveled nozzle, representative of the exhaust system envisioned for a distributed electric propulsion aircraft with a common rectangular duct, produced almost as much noise as the beveled nozzle, with the septae not contributing much reduction in noise.

Noise↗
NASA NTRS1984

Comparison of analytical and experimental steadyand unsteady-pressure distributions at Mach number 0.78 for a high-aspect-ratio supercritical wing model with oscillating control surfaces

The unsteady aerodynamic lifting surface theory, the Doublet Lattice method, with experimental steady and unsteady pressure measurements of a high aspect ratio supercritical wing model at a Mach number of 0.78 were compared. The steady pressure data comparisons were made for incremental changes in angle of attack and control surface deflection. The unsteady pressure data comparisons were made at set angle of attack positions with oscillating control surface deflections. Significant viscous and transonic effects in the experimental aerodynamics which cannot be predicted by the Doublet Lattice method are shown. This study should assist development of empirical correction methods that may be applied to improve Doublet Lattice calculations of lifting surface aerodynamics.

Mccain, W. E.↗
NASA NTRS1954

Effects of Sweep and Thickness on the Static Longitudinal Aerodynamic Characteristics of a Series of Thin, Low-aspect-ratio, Highly Tapered Wings at Transonic Speeds : Transonic-bump Method

An investigation by the transonic-bump technique of the static longitudinal aerodynamic characteristics of a series of thin, low-aspect-ratio, highly tapered wings has been made in the Langley high-speed 7- by 10-foot tunnel. The Mach number range extended from about 0.60 to 1.18, with corresponding Reynolds numbers ranging from about 0.75 x 10(6) to 0.95 x 10(6). The angle of attack range was from -10 degrees to approximately 32 degrees.The effects on drag and lift-drag ratio of a variation in sweep angle from -14.03 degrees to 45 degrees with respect to the quarter-chord line for wings of 3-percent-chord thickness was found to be small in comparison to the effects of a variation in thickness from 2 percent chord to 4.5 percent chord for wings with 14.03 degree sweepback. For the range of variables considered, variations in plan form were considerably more important with regard to longitudinal stability characteristics than the variations in thickness. For the series of basic wings having an aspect ratio of 4, the most hearly linear pitching-moment characteristics were obtained with 26.57 degree of sweepback of the quarter-chord line. However, for the modified series of wings (obtained by clipping the tips of the original wings parallel to the plane of symmetry to give an aspect ratio of 3 and a taper ratio of 0.143), the most nearly linear pitching-moment characteristics were obtained with 36.87 degrees of sweepback. By decreasing the thickness-to-chord ratios from 0.03 to 0.02, a large increase in lift-curve slope was obtained for both the basic and modified wings. All of the wings of both series had fairly large inward shifts of the lateral center-of-pressure location (indicative of tip stalling) with increasing lift coefficient, except those wings having minimum sweepback angles.

Fournier, Paul G↗
NASA NTRS2017

Jet Surface Interaction Noise in a High Aspect Ratio Rectangular Exhaust

A physics-based prediction model is employed to simulate jet surface interaction (JSI) noise in a transversely sheared jet exhaust. The methodology finds application in jets with a high aspect ratio (AR) rectangular exhaust in the proximity of a flat surface. Two component spectra are simulated: (i) mixing/scrubbing noise; (ii) trailing edge noise--and are superimposed to obtain the far field exhaust noise on either side of a nearby surface. This document describes the necessary input parameters (including mean flow and turbulence information for the nozzle exhaust of interest) that should be prepared in order to initiate the simulation for each noise component. Sample input/output files in connection with an 8:1 aspect ratio rectangular exhaust at Mach 0.98 near a rigid surface are described. Jet noise spectra are examined below at operating conditions listed in Table IV. Individual noise components, designated as Scrubbing Noise and Trailing Edge Noise, are presented and their sum Total Noise (Analysis) is compared with Measurement (Refs. 8 and 9) at selective number of observer polar angles at azimuth φ = 90deg. Results are presented on an arc R = 17.80-ft (i.e., R = 100Deq) on both sides of a nearby surface. Although the predicted TE noise component is symmetric with respect to the edge due to symmetry in the propagator, measurements for the majority of cases are not quite symmetric and exhibit a slightly larger peak on the reflected side of the surface. Turbulent mixing/scrubbing noise component has a greater presence on the reflected side, as expected. Figure 13 to Figure 18 show that the peak in the predicted TE component could differ from measurements by as much as 4 dB due to lack of symmetry in measured data, however, the general trend is in agreement with data across the three Mach numbers. The overall sound pressure level (OASPL) associated with the TE noise component follows a U5 velocity scaling in the current modeling (Ref. 4). Directivity predictions for the TE noise component as well as the total noise are shown in Figure 19 (bottom)-and are compared with measurements (top figure) at conditions of Table IV. As anticipated, the TE noise component (dashed-line) overwhelms the directivity factor due to its dominant spectral peak level. Only at small angles to the jet axis the mixing noise component contributes significant enough to weight noticeably on the total noise.

propulsion noise↗
NASA NTRS1983

Wind-tunnel investigation of aerodynamic loading on a 0.237-scale model of a remotely piloted research vehicle with a thick, high-aspect-ratio supercritical wing

Wind-tunnel measurements were made of the wing-surface static-pressure distributions on a 0.237 scale model of a remotely piloted research vehicle equipped with a thick, high-aspect-ratio supercritical wing. Data are presented for two model configurations (with and without a ventral pod) at Mach numbers from 0.70 to 0.92 at angles of attack from -4 deg to 8 deg. Large variations of wing-surface local pressure distributions were developed; however, the characteristic supercritical-wing pressure distribution occurred near the design condition of 0.80 Mach number and 2 deg angle of attack. The significant variations of the local pressure distributions indicated pronounced shock-wave movements that were highly sensitive to angle of attack and Mach number. The effect of the vertical pod varied with test conditions; however at the higher Mach numbers, the effects on wing flow characteristics were significant at semispan stations as far outboard as 0.815. There were large variations of the wing loading in the range of test conditions, both model configurations exhibited a well-defined peak value of normal-force coefficient at the cruise angle of attack (2 deg) and Mach number (0.80).

Byrdsong, T. A.↗
NASA NTRS1979

Influence of optimized leading-edge deflection and geometric anhedral on the low-speed aerodynamic characteristics of a low-aspect-ratio highly swept arrow-wing configuration

An investigation conducted in the Langley 7 by 10 foot tunnel to determine the influence of an optimized leading-edge deflection on the low speed aerodynamic performance of a configuration with a low aspect ratio, highly swept wing. The sensitivity of the lateral stability derivative to geometric anhedral was also studied. The optimized leading edge deflection was developed by aligning the leading edge with the incoming flow along the entire span. Owing to spanwise variation of unwash, the resulting optimized leading edge was a smooth, continuously warped surface for which the deflection varied from 16 deg at the side of body to 50 deg at the wing tip. For the particular configuration studied, levels of leading-edge suction on the order of 90 percent were achieved. The results of tests conducted to determine the sensitivity of the lateral stability derivative to geometric anhedral indicate values which are in reasonable agreement with estimates provided by simple vortex-lattice theories.

Coe, P. L., Jr.↗