SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The main object of these wings was to obtain a high lift without increasing the total drag, and the idea was conceived that, by using a deep high-lift section for the top wing and a medium section for the bottom wing, the mutual interference between the two would be such as to give greater efficiency of the combination as compared with two wings of equal section.
The historical development of NACA airfoils is briefly reviewed. New data are presented that permit the rapid calculation of the approximate pressure distributions for the older NACA four-digit and five-digit airfoils by the same methods used for the NACA 6-series airfoils. The general methods used to derive the basic thickness forms for NACA 6 and 7-series airfoils together with their corresponding pressure distributions are presented. Detail data necessary for the application of the airfoils to wing design are presented in supplementary figures placed at the end of the paper. The report includes an analysis of the lift, drag, pitching-moment, and critical-speed characteristics of the airfoils, together with a discussion of the effects of surface conditions. Available data on high-lift devices are presented. Problems associated with lateral-control devices, leading-edge air intakes, and interference are briefly discussed, together with aerodynamic problems of application. (author)
The results of a wind-tunnel investigation of the NACA 23012, the NACA 23021, and the Clark Y airfoils, each equipped with a cambered external-airfoil flap, are presented in this report. The purpose of the research was to determine the relative merit of the various airfoils in combination with the cambered flap and to investigate the use of the flap as a combined lateral-control and high-lift device.
A performance analysis has been made to determine whether boundary-layer control by suction might reduce the minimum take-off and landing distances of a four-place or five-place airplane or a liaison type of airplane below those obtainable with conventional high-lift devices. The airplane was assumed to have a cruise duration of 5 hours at 60-percent power and to be operating from airstrips having a ground friction coefficient of 0.2 or a combined ground and braking coefficient of 0.4. The payload was fixed at 1500 pounds, the wing span was varied from 25 to 100 feet, the aspect ratio was varied from 5 to 15, and the power was varied from 300 to 1300 horsepower. Maximum lift coefficients of 5.0 and 2.8 were assumed for the airplanes with and without boundary-layer-control --equipment weight was included. The effects of the boundary-layer control on total take-off distance, total power-off landing distance, landing and take-off ground run, stalling speed, sinking speed, and gliding speed were determined.
Tests were made of an 0.309-chord double-slotted flap on an NACA 65, 3-118, a equals 1.0 airfoil section to determine drag, lift, and pitching-moment characteristics for a range of flap deflections. Results indicate that combination of a low-drag airfoil and a double-slotted flap, of which the two parts moved as a single unit, gave higher maximum lift coefficients than have been obtained with plain, split, or slotted flaps on low-drag airfoils. Pitching moments were comparable to those obtained with other high-lift devices on conventional airfoils for similar lift coefficients.
Since the recent more or less extensive adoption of high-lift flaps on airplane wings, the problem of providing satisfactory lateral control without sacrificing a part of the span of the flaps has become one of some importance. The difficulties have been largely a matter of obtaining satisfactory rolling moments with a smoothly graduated action, together with sufficiently small control forces throughout the entire speed range. As part of an investigation including several different lateral-control arrangements to be used with split flaps, the tests reported in this paper were made on one arrangement in which conventional ailerons of narrow chord are used, and a split flap is retracted into the under surface of th wing forward of th ailerons. When the flap is retracted, the arrangement is as sketched in figure 1(a). If a simple form of split flap were used, hinged at its forward edge, the appearance when deflected would be as shown in figure 1(b). The flap if deflected with its leading edge remaining in this forward position would give somewhat less than three fourths of the lift increase of the same flap in the usual rear position. (See reference 1.). If, as shown in figure 1(c), the split flap ahead of th aileron is moved to the rear as the trailing=edge portion is deflected downward, a double advantage is obtained. The deflected flap can be located in the most effective region for high lift (reference 1), and the force required to deflect the flap is reduced. This is the arrangement used in the present tests.
Wind-tunnel tests of a full-scale model of the Republic XP-91 airplane were conducted to determine the longitudinal and lateral characteristics of the wing alone and the wing-fuselage combination, the characteristics of the aileron, and the damping in roll af the wing alone. Various high-lift devices were investigated including trailing-edge split flaps and partial- and full-span leading-edge slats and Krueger-type nose flaps. Results of this investigation showed that a very significant gain in maximum lift could be achieved through use of the proper leading-edge device, The maximum lift coefficient of the model with split flaps and the original partial-span straight slats was only 1.2; whereas a value of approximately 1.8 was obtained by drooping the slat and extending it full span, Improvement in maximum lift of approximately the same amount resulted when a full-span nose flap was substituted for the original partial-span slat.
As part of a general investigation in the NACA 19-foot pressure tunnel to determine stall characteristics and effectiveness of high-lift devices on wings of various sections, tests were made of a tapered. wing having NACA 44R-series airfoil sections. Lift, drag, pitching-moment, and stall characteristics were determined at a Reynolds number of 4,850,000 for the plain wing and for the wing with partial-and with full-span split flaps. The stall progressed slowly over The plain wing; a gradual loss of lift for angles of attack up to and beyond that for the maximum lift coefficient resulted. As Compared with the stall of the plain wing, the initial stall of the wing with either partial-span or full-span flaps deflected occurred at a higher angle of attack and the stall progressed much more rapidly. The maximum lift coefficients at a Reynolds number of 4,850,000 were 1.35 for the plain wing, 2.25 for the wing with partial-span flaps at 60 deg, and 2.67 for the wing with full-span flaps at 60 deg. The positions of the aerodynamic center, in terms of mean chords back of the leading edge of the root section, were approximately 0.458 with no flaps, 0.483 with partial-span flaps at 60 deg, and 0.498 with full-span flaps at 60 deg.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Two-dimensional tests were made of an NACA 0006 airfoil with area suction applied to a porous region on a 0.3-chord trailing-edge flap deflected 50 degrees. The lift with suction approached the value computed from thin-airfoil theory. The lift gains and suction quantity requirements were unaffected by the perforation patterns of the surface over a wide range of hole sizes and spacings.
This report gives the characteristics of a wing with an auxiliary airfoil mounted near its trailing edge and used as a flap. The tests were made with a 10 by 60 inch Clark Y main airfoil and an NACA 0012 flap having a chord equal to 15 percent of the main wing chord. The axis of the flap in all cases was on the flap chord and 20 percent back from its leading edge. The optimum location of the flap axis relative to the main wing for maximum lift was found to be 1.25 percent of the main wing chord behind the trailing edge and 2.5 percent below the chord. In this position C(sub L max) was increased from 1.250 (for the plain wing) to 1.810 at 45 degrees deflection of the flap and C(sub D min) was decreased form 0.0155 to 0.0146 at minus 5 degrees deflection, the coefficient in each case being based on the sum of the flap and wing areas. No serious adverse change in lateral stability was found to result from the use of the flap in the optimum position.
An investigation was made in the NACA 7 by 10 foot wind tunnel to find the increase in maximum lift coefficient which could be obtained by providing a model wing with both a Fowler trailing-edge extension flap and a Handley Page type leading-edge slot. A conventional Handley page slot proportioned to operate on the plain wing without a flap gave but a slight increase with the flap; so a special form of slot was developed to work more effectively with the flap. With the best combined arrangement the maximum lift coefficient based on the original area was increased from 3.17, for the Fowler wing, to 3.62. The minimum drag coefficient with both devices retracted was increased in approximately the same proportion. Tests were also made with the special-type slot on the plain wing without the flap. The special slot, used either with or without the Fowler flap, gave definitely higher values of the maximum lift coefficient than the slots of conventional form, with an increase of the same order in the minimum drag coefficient.
An investigation was made in the NACA 7- by 10-foot wind tunnel to determine the effect of slot-lip location on the aerodynamic section characteristics of an NACA 23012 airfoil with a 30-percent-chord slotted flap. Tests were made with slot lips located at 90 and 100 percent of the airfoil chord and with two different flap shapes. The results are compared with a slotted flap previously developed by the National advisory Committee for Aeronautics with a slot lip located at 83 percent of the airfoil chord. The extension of the slot lip to the rear increased the section lift and pitching-moment coefficients. Comparisons made on a basis of pitching moment for a given tail length show that the Fowler type flap, lip extended to trailing edge of the airfoil, has the greatest section lift coefficient. For moderate tail lengths, 2 to 3 chord lengths, there was only a slight difference between the previously developed slotted flap and the slotted flap with slot lip extended to 90 percent of the airfoil chord. Of the three flaps tested, the Fowler flap had the lowest drag coefficient at high lift coefficients. The extension of the lower surface at the leading edge of the slot had a negligible effect on the profile drag of the airfoil-flap arrangement with the flap deflected when the lip terminated at 90 percent of the airfoil chord.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.