Search NASA⌕ Search

SEARCH · Search NASA

Results for “High-temperature Creep”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Additively manufactured and cast high-temperature aluminum alloys for electric vehicle brake rotor application

Electric vehicle brake rotors demand lightweight, high thermal conductivity materials with good resistance to wear, creep, salt corrosion, and thermal fade, all of which present challenges to the traditionally used cast iron. In this work, we investigated the braking performance of recently developed high-temperature aluminum alloys in both cast and 3D printed forms, that possess excellent microstructural and mechanical stability at elevated temperatures. Three aluminum alloys, Al-6Cu-Mn-Zr, Al-9Cu-Mn-Zr, and Al-Ce-Ni-Mn-Zr and a reference cast iron were tested on a sub-scale brake tester against a commercial brake pad material over a range of sliding speeds between 2 and 15 m/s. The performance of these alloys was evaluated for wear resistance, friction behavior, temperature elevation, and surface morphological change. Although all three candidate alloys had lower wear-resistance than cast iron, Al-Ce-Ni-Mn-Zr showed a significantly reduced wear rate in comparison to the Al-Cu-Mn-Zr alloys. Moreover, Al-Ce-Ni-Mn-Zr alloy had the most consistent friction behavior at all sliding speeds and good fade resistance, as the coefficient of friction did not dramatically decrease with temperature rise but stayed within a desirable range of 0.35–0.50 instead. The superior wear resistance and braking performance of the Al-Ce-Ni-Mn-Zr alloy were attributed to its higher hardness, and high temperature yield strength and creep resistance compared with the Al-Cu-Mn-Zr alloys. In conclusion, the results suggest that the braking performance of these aluminum alloys could be further enhanced by increasing the hardness and forming a more stable transfer layer on the sliding surface.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Laser Powder Bed Fusion Manufactured Alloys 625 and 282 and Properties Relevant to Advanced Nuclear Components

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Large printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. Annealing at 1,180°C for 1 h followed by 4 h at 800°C in a high density of 50 nm γ′-strengthening precipitates as well as partial recrystallization resulted in a bimodal grain distribution. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Printing defects were the likely reason for the lower creep performance of LPBF 282 and could be suppressed by optimizing the build configuration. Printing 625 on an EOS M290 machine using the recommended EOS parameters resulted in a very low defect density. Superior creep strength at 725°C was observed for the as-printed LPBF 625 along the build direction when compared with wrought 625. No defect larger than ~50 µm could be detected by X-ray computed tomography in the as-printed conditions and after creep testing for 1,000 h at 725°C and 150 MPa. Small, needle-like δ-phase precipitates were observed after creep testing for 100 h at 725°C and 200 MPa. The rapid formation of the γ phase is directly related to the initial Nb and Mo segregation in the LPBF 625 cell walls, and its effect on the alloy’s high-temperature performance will be evaluated. Solution annealing was carried out at 1,150°C for 1 h and led to full recrystallization of the alloy. A decrease in strength and increase in ductility were observed after solution annealing, and the alloy recrystallization resulted in isotropic tensile properties at room temperature, contrary to what was observed for the as-printed LPBF 625.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Microstructure & Mechanical Properties of Scaled Thermally Aged LPBF 316H SS Builds

As part of the US Department of Energy’s Advanced Materials and Manufacturing Technologies program’s mission to accelerate qualification of advanced manufacturing pathways for nuclear applications, laser powder bed fusion (LPBF) 316H stainless steel (SS) has been selected as a model system to develop a rapid code case framework. This effort directly addresses the grand challenges of (1)expanding the limited portfolio of materials currently codified for elevated-temperature nuclear structural service under Section III, Division 5of the American Society of Mechanical Engineers’ Boiler and Pressure Vessel Code; and (2) significantly reducing qualification timelines that traditionally exceed a decade. The strategic importance of LPBF 316H lies in its immediate industrial relevance, existing data foundation from wrought 316H, and alignment with ongoing code case development for LPBF 316L.Prior work revealed accelerated precipitation of deleterious secondary phases and reduced creep ductility in as-printed LPBF 316H. Building on that prior research, FY2025activities focused on establishing an understanding of the key failure mechanisms of crept 316H specimens to aid in code case development and on evaluating stress relief (SR) parameters on the high-temperature performance and thermal aging-induced degradation of tensile and fracture behavior in LPBF316H.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure and Mechanical Properties of Scaled Thermally Aged LPBF 316H SS Builds

As part of the US Department of Energy’s Advanced Materials and Manufacturing Technologies program’s mission to accelerate qualification of advanced manufacturing pathways for nuclear applications, laser powder bed fusion (LPBF) 316H stainless steel (SS) has been selected as a model system to develop a rapid code case framework. This effort directly addresses the grand challenges of (1) expanding the limited portfolio of materials currently codified for elevated-temperature nuclear structural service under Section III, Division 5 of the American Society of Mechanical Engineers’ Boiler and Pressure Vessel Code; and (2) significantly reducing qualification timelines that traditionally exceed a decade. The strategic importance of LPBF 316H lies in its immediate industrial relevance, existing data foundation from wrought 316H, and alignment with ongoing code case development for LPBF 316L. Prior work revealed accelerated precipitation of deleterious secondary phases and reduced creep ductility in as-printed LPBF 316H. Building on that prior research, FY 2025 activities focused on establishing an understanding of the key failure mechanisms of crept 316H specimens to aid in code case development and on evaluating stress relief (SR) parameters on the high-temperature performance and thermal aging induced degradation of tensile and fracture behavior in LPBF 316H.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Chain entanglements enable regeneration of high-performance thermosets

Thermoset plastics underpin structural materials, electronics and transportation, yet the permanent covalent networks that prevent flow and provide dimensional stability also make them difficult to recycle without sacrificing performance. In this work we show that high-performance thermosets can be built around dense chain entanglements, the physical interlacing of long polymer strands, rather than dense permanent crosslinks, with only a small number of selectively cleavable junctions preserving connectivity. Long, rigid, entangled polyolefin backbones generated by frontal polymerization form glassy polymers with high stiffness, high toughness and excellent creep suppression yet can be fully deconstructed into soluble, linear oligomers. Varying oligomer length and end-group chemistry enables their reuse as re-entangling building blocks that regenerate thermosets with thermal and mechanical properties that remain unchanged across generations. The strategy further extends to high-temperature fibre-reinforced composite matrices and additively manufactured structures, establishing chain entanglement as a design principle for durable, regenerable thermosets.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Fatigue Performance of an Improved Creep Strength 10%Cr Steel

The deployment of 9-12% Cr steels for elevated temperature applications up to 650 °C presents a cost-effective alternative to more expensive nickel-based alloys in steam turbine power generation. To enhance creep resistance at this temperature range, a novel ferritic-martensitic steel, designated CPJ7, was developed and fabricated at the National Energy Technology Laboratory. The alloy design aimed to mitigate the transformation of strengthening carbides into deleterious phases that degrade creep performance. Results have demonstrated that CPJ7 exhibits favorable creep and oxidation resistance at 650 °C. However, its fatigue performance remains unexplored. This study builds upon prior research by evaluating the low cycle fatigue behavior of CPJ7 and verifying that modifications beneficial to creep performance were not detrimental to the fatigue performance. The alloy was tested at both 650 °C and ambient temperature under fully reversed bending conditions (R = − 1) and a load ratio of 0.05. Furthermore, the alloy exhibits cyclic softening, a behavior consistent with other 9-10 wt.% Cr steels. Analysis of the microstructure and hysteresis loops further corroborate cyclic softening mechanisms typical of ferritic-martensitic steels. Overall, the fatigue performance of CPJ7 meets or exceeds that of P91 steel, demonstrating its potential for high-temperature structural applications.

9% Cr ferritic-martensitic steel↗
DOE OSTI2025

Summary of Graphite Data Stored within NDMAS

The Graphite Technology Development Project provides data to support the design of graphite core components within specific reactor service conditions of the next generation of high-temperature, gas-cooled nuclear reactors. Physical, mechanical, and thermal properties of nuclear grade graphite were characterized for specimens that were unirradiated, irradiated, and irradiated under various stress conditions. The material properties include diameter, length, mass, density, compressive strength, tensile strength, flexural strength, modulus, resistivity, thermal diffusivity, and thermal expansion coefficient. Baseline graphite specimens are unirradiated from different grades (2114, IG-110, NBG-17, NBG-18, and PCEA) and different types used in different characterization tests (compressive, flexural, tensile, one-inch cylinder, and quarter-inch cylinder). The Advanced Graphite Creep (AGC) irradiation specimens are from a much larger number of grades and cylinder types (creep, piggyback, and pencil). For baseline graphite, characterization data for 7,756 specimens extracted from thirteen graphite billets were captured to the NDMAS database. For AGC experiments, four irradiation campaigns have been completed: AGC-1, AGC-2, AGC-3, and AGC-4. The ongoing HDG-1 (High-Dose Graphite) experiment, which began irradiation with Cycle 168B on August 26, 2020, includes specimens previously irradiated in AGC-2 in addition to the specimens originally destined for AGC-5.. Besides the characterization data, the AGC data includes irradiation monitoring and physics data representing the irradiation conditions of AGC specimens. Currently, all data for AGC-1, AGC-2, and AGC-3 have been captured to the NDMAS database. Only AGC-4 pre-irradiation and irradiation monitoring data have been captured, and HDG-1 pre-irradiation data are in process of being captured for unirradiated specimens. To date, a total of 38,149 material property records have been captured into NDMAS database for baseline and AGC specimens. All characterization data are qualified for use according to their perspective data verification reports. For the AGC irradiation campaigns, a total of 41,502 qualified physics calculation records were added for AGC-1, AGC-2, and AGC-3. Finally, a total of 173,698,505 AGC irradiation monitoring data records (thermocouple temperature, gas flow rate, gas pressure, gas moisture, applied load, and specimen displacement) have been captured to NDMAS; the majority of those records (~94%) are qualified data records.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Design of Novel Hot Gas Component for Gas Turbine Engines Enabled by Materials and Additive Manufacturing Process Development

This CRADA project was the result of a project award under FOA-DOE-0001980. The overarching FOA project team consisted of researchers from Carpenter Technology Corporation (CTC), Solar Turbines Incorporated (Solar), Pennsylvania State University (PSU), University of California-Santa Barbara (UCSB), and Oak Ridge National Laboratory (ORNL). Evaluations were conducted on two high-γ’ superalloys that were designed by CTC and the UCSB. One alloy named GammaPrint-700 (GP-700) is a cobalt-base superalloy. The other alloy named GammaPrint-1100 (GP-1100) is a nickel-base (Ni-base) superalloy. PSU provided expertise and experimental testing of the thermal performance of AM micro-cooling architectures. ORNL provided expertise with the AM superalloy materials characterization and AM processing science. Solar provided turbine component design expertise. The focus of this CRADA report is to document the efforts between ORNL and CTC towards the development of superalloys designed for AM. The project goal was to use an AM processable high-temperature superalloy and design for Additive Manufacturing (DfAM) techniques to design an efficient turbine component (i.e. a turbine tip shoe) with enhanced cooling features that can only be fabricated through additive manufacturing (AM). The efficiencies of existing combined heat and power (CHP) engines are capped by both component design and materials limitations. However, AM of a tip shoe component from a γ’strengthened superalloy offers the design flexibility to increase the efficiency and power of an industrial gas turbine. This project brought about advancements in the DfAM tip shoe design space and in the area of high temperature superalloys processable through laser powder bed fusion (LPBF) AM. State of art computation design tools were utilized to optimize unique cooling features into a tip shoe component design. A two-prong materials development approach was taken to support development of the AM tip shoe geometry. The first approach centered on investigating the processability and the appropriate process science for the industry standard high-γ’ nickel-base (Ni-base) superalloy Mar-M247. This superalloy is typically cast and considered non-weldable by traditional welding standards. In the course of this work, the alloy was not deemed feasible for process scale-up due to significant cracking issues during printing. The second approach focused on the development and evaluation of a novel cobalt-base superalloy, GammaPrint™-700 (GP-700 and a Ni-base superalloy, GammaPrint™-1100 (GP-1100) designed to mitigate the significant AM processing issues with Mar-M247. The processability of these two alloys were investigated through electron beam melting (EBM) binder-jet AM (BJAM), and LPBF as a risk mitigation for manufacturability. To be considered a candidate material for down-selection to proceed to full-scale AM tip shoe engine testing trials, the high temperature creep rupture strength was required to achieve at a minimum, a Larsen Miller Parameter (LMP) increase of 10.9% over the baseline material LPBF AM Hastelloy X.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Recrystallization driven softening and heating rate dependencies of FeCrAl nuclear fuel cladding during accident transients

A refined understanding of FeCrAl cladding behavior during rapid transients is critical for its potential deployment in light-water reactors. Current assessments focus on transient burst testing metrics such as balloon geometry, burst temperature, and hoop stress, often used as proxies for simpler conventional tensile properties. However, directly correlating isothermal tensile and creep data with accident transient scenarios remains a challenge, although it is essential for high fidelity model development. Recent modeling based on tensile tests up to 800 °C, conducted with both immediate loading and a 10-minute soak, showed that immediate loading better predicts experimental burst temperatures, indicating a thermal softening effect. Building upon this observation, the current study connects transient performance, microstructural evolution, and high-temperature tensile properties by leveraging results from C26M claddings burst tests performed at heating rates of 1–50 °C/s and hoop stresses from 25 to 100 MPa. At 25 MPa, rupture temperatures varied by only 6 °C, but at 100 MPa, the difference reached 116 °C, with faster heating yielding higher burst temperatures. Microstructural analysis identified recrystallization as the primary cause of heating rate-dependent softening, eliminating prior cold-working. In-situ thermomechanical data linked ballooning onset to localized instabilities, similar to ultimate tensile strength behavior in conventional tensile tests. High heating rates correlated with immediate loading tensile data, while lower rates matched soaked data. Furthermore, by linking burst performance to microstructural evolution and tensile properties, this work provides a foundation for more accurate modeling of FeCrAl claddings and potentially other Fe-based materials under accident conditions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

BISON analyses of TRISO fuel performance, its dependence on time-at-temperature, and possible implications for fuel design and qualification

The Advanced Gas Reactor Fuel Development and Qualification (AGR) program has established a substantial technical foundation to support private entry into the U.S. high-temperature gas-cooled reactor market. However, emerging tristructural isotropic (TRISO)-fueled reactor applications include small modular reactors and microreactors with longer fuel residence times, which may expose fuels to higher time-at-temperature (TAT) values than were explored by the AGR program. Increased TAT could affect diffusive and thermomechanical behaviors such as Pd penetration, fission gas release, creep, and fission product transport. In this work, we applied multiscale best-estimate BISON fuel performance modeling to assess these effects within a representative design space based on the AGR-5/6/7 experiment and analyzed trends in predicted particle and compact fuel performance metrics with possible implications for near-term fuel design and qualification. BISON unambiguously predicted that TRISO fuel performance is sensitive to TAT. Increasing TAT was not predicted to increase the magnitude of failure-inducing tangential stresses in particle coating layers. Predictions obtained using a mechanistic model for Pd penetration indicated that penetration depth does not depend strongly on TAT. While these observations suggest that AGR testing provides a conservative upper bound for the steady-state operation of TRISO particles at lower powers and higher residence times, BISON also predicted that the release of poorly retained Ag would increase with TAT. Because these analyses applied models to extrapolate beyond the available experimental data, the authors recommend performing targeted experiments to confirm these predictions. Nevertheless, these predictions may provide reactor developers with enough confidence to make near-term design decisions associated with the potential fuel performance trade-offs of increasing TAT.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

High-temperature mechanical properties of a γ′-strengthened Co-based superalloy designed for additive manufacturing

GammaPrint®-700 is a recently developed high γ′ (∼70% volume fraction) CoNi-based superalloy designed to combine high-temperature mechanical performance with laser powder bed fusion processability. Room-temperature yield strength ranged from 610 to 658 MPa and increased to 661 MPa (longitudinal) and 730 MPa (transverse) at 760 °C. The creep behavior compared favorably to high-γ′ Ni-based superalloys manufactured via laser powder bed fusion such as Incoloy® 939 and Inconel® 738LC. In-situ neutron diffraction data measured during creep revealed that plastic deformation was largely localized to the γ phase at 760 °C, allowing the γ’ phase to elastically compensate and maintain creep strain resistance. Furthermore, at 900 °C, this load sharing behavior was weakened, contributing to accelerated creep rate and rupture.

Creep↗
DOE OSTI2025

srlife : A software tool for estimating the life of high temperature concentrating solar receivers. Part II – Ceramic receivers

As Concentrating Solar Power (CSP) technologies aim for higher operating temperatures to enhance efficiency and meet industrial process heat demands, high-temperature metallic materials, including nickel-based superalloys, face challenges in maintaining structural integrity. Advanced ceramics offer a promising alternative due to their superior high-temperature strength. However, accurately assessing the performance of ceramic components requires a fundamentally different approach from that used for metallic components. This Part II of a two-part paper describes the integration of ceramic statistical failure models within srlife – an open-source tool for predicting the life of high-temperature CSP receivers. These models account for the inherent variability in ceramic strength, as well as the effects of subcritical crack growth (SCG) under high temperature cyclic loads. Here, the paper includes an example problem that demonstrate the process of evaluating ceramic receivers using srlife. Part I details the life estimation process for metallic receivers (i.e. creep-fatigue life) along with input and output data structure, thermohydraulic analysis, and structural analysis. The complete tool is available as open-source software at https://github.com/srlife-project/srlife and can be installed via the PyPi package manager (https://pypi.org). By supporting both ceramic and metallic receiver analyses, srlife facilitates fair comparisons between competing metallic and ceramic designs, enabling accurate evaluations of plant efficiency and the economic benefits of ceramic solar receivers and other components.

High temperature ceramic receivers↗
DOE OSTI2025

Structural Design and Modeling of MARVEL Primary Coolant System Using the ASME Section III, Division 5, Code

This paper presents the structural design and supporting analysis for the Microreactor Applications Research Validation and Evaluation (MARVEL) primary coolant system (PCS) using the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code Section III, Division 5, rules. MARVEL is a liquid metal–cooled microreactor intended to provide experimental capabilities for the rapid testing and development of microreactor technologies. The PCS utilizes high-temperature sodium-potassium liquid metal as the primary coolant and operates at a design temperature of 570°C, necessitating the consideration of creep-related failure mechanisms. The base metal for the PCS is 316H stainless steel, and the weldments are made with a 16-8-2 filler. The design approach incorporates the current base code rules along with ASME code cases N-924, N-861, and N-862 to address primary load, ratcheting, and creep-fatigue evaluations, respectively. The reactor’s operation involves complex thermal and mechanical interactions due to natural convective flow and differential thermal expansion between components. In conclusion, this paper discusses the structural engineering challenges encountered, such as managing thermal stresses in the distribution plenum and guard vessel, and outlines the strategies implemented to meet the code requirements, including design modifications and operational constraints.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2025

A high-temperature Rutherford Backscattering Spectrometry apparatus for in situ material characterization

A new methodology for high-temperature Rutherford Backscattering Spectrometry (HT-RBS) has been developed to enable in situ material characterization at elevated temperatures. A 3.5 MeV proton beam penetrates a 10-µm-thick 316L stainless steel foil mounted on a graphite substrate, with backscattered signals detected using an HT-RBS system. Conventional semiconductor detectors, primarily based on silicon, suffer significant performance degradation at temperatures higher than ~ 60 °C due to increased leakage current and noise, leading to signal distortion and failure. Here, to preserve spectral quality, a 5 µm aluminum foil shields the detector from thermal radiation, allowing reliable operation up to 900 °C at the target. A rotatable shutter provides additional thermal isolation during data collection pauses. In situ measurements of areal density changes of 316L stainless steel were conducted to validate the technique, revealing consistency with the known thermal expansion coefficient. The method facilitates seamless switching between irradiation and analysis, enabling continuous studies. This approach supports in situ investigations of diffusion, void swelling, creep, and corrosion, offering a versatile tool for advanced materials research.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermomechanical Modeling and Analysis of a High-Temperature Light Trapping Planar Cavity Receiver

Solar energy harnessed through concentrating solar power (CSP) systems offers a promising path to sustainable energy production, with the efficiency and longevity of these systems relying on key components like solar receivers. This study analyzes the thermomechanical behavior of an innovative enclosed light-trapping solar receiver optimized for particle heating applications. The receiver utilizes sheet metal alloys to form enclosed cavities that reflect and trap incoming solar flux, as well as enclosed channels that contain fluidized particle beds absorbing solar heat. Finite element analysis (FEA) is applied to predict the receiver's thermomechanical performance under extreme solar flux conditions. Temperature distributions from a thermal model simulating a multi-panel assembly at steady state are input into the FEA thermomechanical model for stress analysis. A key aspect of the analysis focuses on evaluating creep-fatigue damage, with a design target of achieving a 30- year service life. Various stress relief techniques are also proposed to extend the receiver's service life. The results highlight the significant impact of the particle-to-wall heat transfer coefficients (HTCs), ranging from 800 W/m2*K to 1400 W/m2*K. The 800 W/m2*K case shows a maximum von Mises stress of 164 MPa, while the 1400 W/m2*K case reduces it to 150 MPa. The creep life increases from 4,000 hrs in the 800 W/m2*K case to over 100,000 hrs in the 1400 W/m2*K case with Inconel 740H used, indicating that higher HTCs reduce stress and extend lifespan. This research advances the design of high-efficiency, low-stress solar receivers for particle-based thermal energy storage in CSP and industrial heating applications.

concentrating solar power↗
DOE OSTI2025

Design of Novel Hot Gas Component for Gas Turbine Engines Enabled by Materials and Additive Manufacturing Process Development

This CRADA project was the result of a project award under FOA-DOE-0001980. The overarching FOA project team consisted of researchers from Carpenter Technology Corporation (CTC), Solar Turbines Incorporated (Solar), Pennsylvania State University (PSU), University of California-Santa Barbara (UCSB), and Oak Ridge National Laboratory (ORNL). Evaluations were conducted on two high-γ’ superalloys that were designed by CTC and the UCSB. One alloy named GammaPrint-700 (GP-700) is a cobalt-base superalloy. The other alloy named GammaPrint-1100 (GP-1100) is a nickel-base (Ni-base) superalloy. PSU provided expertise and experimental testing of the thermal performance of AM micro-cooling architectures. ORNL provided expertise with the AM superalloy materials characterization and AM processing science. Solar provided turbine component design expertise. The focus of this CRADA report is to document the efforts between ORNL and CTC towards the development of superalloys designed for AM. The project goal was to use an AM processable high-temperature superalloy and design for Additive Manufacturing (DfAM) techniques to design an efficient turbine component (i.e. a turbine tip shoe) with enhanced cooling features that can only be fabricated through additive manufacturing (AM). The efficiencies of existing combined heat and power (CHP) engines are capped by both component design and materials limitations. However, AM of a tip shoe component from a γ’strengthened superalloy offers the design flexibility to increase the efficiency and power of an industrial gas turbine. This project brought about advancements in the DfAM tip shoe design space and in the area of high temperature superalloys processable through laser powder bed fusion (LPBF) AM. State of art computation design tools were utilized to optimize unique cooling features into a tip shoe component design. A two-prong materials development approach was taken to support development of the AM tip shoe geometry. The first approach centered on investigating the processability and the appropriate process science for the industry standard high-γ’ nickel-base (Ni-base) superalloy Mar-M247. This superalloy is typically cast and considered non-weldable by traditional welding standards. In the course of this work, the alloy was not deemed feasible for process scale-up due to significant cracking issues during printing. The second approach focused on the development and evaluation of a novel cobalt-base superalloy, GammaPrint™-700 (GP-700 and a Ni-base superalloy, GammaPrint™-1100 (GP-1100) designed to mitigate the significant AM processing issues with Mar-M247. The processability of these two alloys were investigated through electron beam melting (EBM) binder-jet AM (BJAM), and LPBF as a risk mitigation for manufacturability. To be considered a candidate material for down-selection to proceed to fullscale AM tip shoe engine testing trials, the high temperature creep rupture strength was required to achieve at a minimum, a Larsen Miller Parameter (LMP) increase of 10.9% over the baseline material LPBF AM Hastelloy X.

36 MATERIALS SCIENCE↗
DOE OSTI2025

LAROMance Grade 91 Model Integration in NEML2

New reactor designs are targeting higher operating temperatures for increased thermal efficiency when compared to the current fleet of light water reactors. Designing structural components for these high temperature environments with reliable long-term operations requires material models that can accurately capture the deformation mechanisms active in these environments. The LAROMance surrogate material models are based on a database of mechanistic crystal plasticity simulations for high-temperature conditions. Inputs to the LAROMance models reflect the microstructural pedigree of the material, like dislocation densities and precipitate contents. Based on the evolution of these microstructural features, the LAROMance model provides the engineering scale constitutive model response. The LAROMance model was recently parameterized for Grade 91, a high temperature alloy. In the present work, the Grade 91 LAROMance model is implemented in the New Material Model Library, version 2 (NEML2). NEML2 provides a modular way to build material models from smaller blocks and was developed to vectorize the material update to efficiently run on modern computational architectures with graphics processing unit accelerators. NEML2 constitutive models can be used in simulations based on the multiphysics object-oriented simulation environment (MOOSE). This report provides details on the implementation of the Grade 91 LAROMance model in NEML2 and its verification of engineering scale finite element simulations in MOOSE.

42 - ENGINEERING↗
DOE OSTI2025

Manufacturability and performance response of developed Ni-based alloys for reactor environments

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) at Oak Ridge National Laboratory and by laser powder directed energy deposition (LP-DED) at Idaho National Laboratory have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. For both the LPBF and LP-DED 282 alloys, annealing at 1,180°C for 1 h resulted in partial recrystallization and a bimodal grain distribution, and subsequent aging for 4 h at 800°C led to the formation of a high density of nano-size γ′-strengthening precipitates. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF and LP-DED 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation in the LPBF 282 alloy during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Creep cavitation and cracking at grain boundaries were also observed for the LP-DED 282 alloy, and optimization of the printing strategies and postheat treatments will be needed to fabricate high-performance 282 components for high-temperature nuclear applications.

36 MATERIALS SCIENCE↗