Heavy Ion-Induced Single-Event Leakage Current and Burnout in Homojunction GaN PIN Diodes
Not Available
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
Abstract not provided.
We report on the first pn junction solar cells grown by homoepitaxy of GaAs using close space vapor transport (CSVT). Cells were grown both on commercial wafer substrates and on a CSVT absorber film, and had efficiencies reaching 8.1%, open circuit voltages reaching 909 mV, and internal quantum efficiency of 90%. The performance of these cells is partly limited by the electron diffusion lengths in the wafer substrates, as evidenced by the improved peak internal quantum efficiency in devices fabricated on a CSVT absorber film. Unoptimized highly-doped n-type emitters also limit the photocurrent, indicating that thinner emitters with reduced doping, and ultimately wider band gap window or surface passivation layers, are required to increase the efficiency.
Highlights: • The effects of the various reaction conditions are investigated. • Different photocatalytic activities attributed to the different homogeneity and crystallinity of the nanoparticles. • Combination of good crystallinityand homogeneityresulted in an excellent photocatalytic activity. - Abstract: Zn{sub 0.5}Cd{sub 0.5}S nanoparticles with phase homojunctions were prepared by a one-step hydrothermal method with thioacetamide as sulfur source. The effects of the various reaction conditions, such as initial concentrations of Zn and Cd ions, initial content of sulfur source in the reaction mixture, and the temperature rising rate, are investigated. The photocatalytic activities for H{sub 2} evolution from water in the presence of sacrificial reagents of these Zn{sub 0.5}Cd{sub 0.5}S nanoparticles were significantly affected by the reaction conditions. These differences on the photocatalytic activities can be attributed to the different homogeneity and crystallinity of the nanoparticles prepared at different reaction conditions. A faster reaction rate leads to the formation of Zn{sub 0.5}Cd{sub 0.5}S nanoparticles with bad crystallinity, but good homogeneity. On the contrary, a slow reaction rate results in a bad homogeneity, but better crystallinity. Combination of good crystallinity and homogeneity in a Zn{sub 0.5}Cd{sub 0.5}S nanocomposite resulted in an excellent photocatalytic activity. The highest rate of H{sub 2} evolution achieved for these phase-homojunctions materials under visible-light irradiation (λ ≥ 420 nm) reached 1252.7 μmol h{sup −1} with an apparent quantum efficiency of 21.46% at 420 nm. The H{sub 2} evolution rate did not reduce distinctively in a continuous 15 hour test for H{sub 2} evolution, indicating an excellent stability for this material. This work not only demonstrates a facile method to produce highly active phase-homojunctions containing Zn{sub 0.5}Cd{sub 0.5}S solid solutions for photocatalytic hydrogen production from the perspective of controlling various reaction conditions, but also provides new insights into understanding the importance of the homogeneity and crystallinity for enhancing photocatalytic activity and stability of Zn{sub 0.5}Cd{sub 0.5}S solid solutions. It is expected that the strategies of modifying the homogeneity and crystallinity by controlling various reaction conditions can be extracted and used when designing other efficient and robust photocatalysts in the future.
We describe an approach to reduce the contact resistance at compositional conducting/semiconducting indium-zinc-oxide (IZO) homojunctions used for contacts in thin film transistors (TFTs). By introducing silver nanoparticles (Ag NPs) at the homojunction interface between the conducting IZO electrodes and the amorphous IZO channel, we reduce the specific contact resistance, obtained by transmission line model measurements, down to ∼10{sup −2 }Ω cm{sup 2}, ∼3 orders of magnitude lower than either NP-free homojunction contacts or solid Ag metal contacts. The resulting back-gated TFTs with Ag NP contacts exhibit good field effect mobility of ∼27 cm{sup 2}/V s and an on/off ratio >10{sup 7}. We attribute the improved contact resistance to electric field concentration by the Ag NPs.
Narrow bandgap tin-lead (NBG Sn-Pb) perovskites generally have a high density of unintentional p-type self-doping, which reduces the charge carrier lifetimes, diffusion lengths and device efficiencies. Here, we demonstrate a p-n homojunction across the Sn-Pb perovskite resulted from a gradient doping by Ba 2+ . We report that 0.1 mol% Ba 2+ can effectively compensate the p-doping of Sn-Pb perovskites or even turns it to n-type without changing its bandgap. Ba 2+ cations are found to stay at the interstitial sites and work as shallow electron donor. In addition, Ba 2+ cations show a unique heterogeneous distribution in perovskite film. Most of the barium ions stay in the top 600 nanometer region of the perovskite films and turn it into weakly n-type, while the bottom portion of the film remains to be p-type. The gradient doping forms of a homojunction from top to bottom of the perovskite films with a built-in field that facilitates extraction of photogenerated carriers, resulting an increased carrier extraction length. Furthermore, this strategy enhanced the efficiency of Sn-Pb perovskite single-junction solar cells to over 21.0% and boosted the efficiencies of monolithic perovskite-perovskite tandem solar cells to 25.3% and 24.1%, for active areas of 5.9 mm2 and 0.94 cm 2 , respectively.
Cu(In,Ga)Se{sub 2} (CIGSe) pellets at different Sn contents were fabricated by reactive liquid-phase sintering at 600–700 °C with the help of sintering aids of Sb{sub 2}S{sub 3} and Te. Powder preparation was based upon the molecular formula of Cu{sub 0.9}[(In{sub 0.7−x}Sn{sub x}Ga{sub 0.3}){sub 0.9}Sb{sub 0.1}](S{sub 0.15}Te{sub 0.2}Se{sub 1.65}) or Sn-x-CIGSe. Morphology, structure, and electrical property of Sn-doped CIGSe bulks were investigated. The composition of Sn-doped CIGSe is purposely designed for studying the doping effect on the CIGSe performance. The unexpected increase in hole concentration of CIGSe due to the donor doping is rationalized. A controllable n-type semiconductor is deliberately achieved for Sn-0.15-CIGSe and important for making a p/n homojunction in CIGSe solar cells. - Graphical abstract: The controls in defect type and electrical properties of Cu(In,Ga)Se{sub 2} by doping Sn{sup 4+} on the In{sup 3+} site. Highlights: • n-type Sn-CIGSe with n{sub e} of 6.4×10{sup 16} cm{sup −3} and μ{sub e} of 2.3 cm{sup 2}/V s was obtained. • This n-type Sn-CIGSe was obtained by material design and composition control. • The reported n-type CIGSe was obtained from the Zn/CIGSe and CdS/CIGSe bilayers. • Extrinsic donor doping was explored through the results of electrical properties. • A n/p homojunction with Sn-CIGSe and undoped one can be used for solar cell devices.
A new compact modeling approach is presented which describes the full current-voltage (I-V) characteristic of high-performance (aggressively scaled-down) tunneling field-effect-transistors (TFETs) based on homojunction direct-bandgap semiconductors. The model is based on an analytic description of two key features, which capture the main physical phenomena related to TFETs: (1) the potential profile from source to channel and (2) the elliptic curvature of the complex bands in the bandgap region. It is proposed to use 1D Poisson's equations in the source and the channel to describe the potential profile in homojunction TFETs. This allows to quantify the impact of source/drain doping on device performance, an aspect usually ignored in TFET modeling but highly relevant in ultra-scaled devices. The compact model is validated by comparison with state-of-the-art quantum transport simulations using a 3D full band atomistic approach based on non-equilibrium Green's functions. It is shown that the model reproduces with good accuracy the data obtained from the simulations in all regions of operation: the on/off states and the n/p branches of conduction. This approach allows calculation of energy-dependent band-to-band tunneling currents in TFETs, a feature that allows gaining deep insights into the underlying device physics. The simplicity and accuracy of the approach provide a powerful tool to explore in a quantitatively manner how a wide variety of parameters (material-, size-, and/or geometry-dependent) impact the TFET performance under any bias conditions. The proposed model presents thus a practical complement to computationally expensive simulations such as the 3D NEGF approach.
We fabricated epitaxial CdTe:In/CdTe:As homojunction and CdZnTe/CdTe and CdMgTe/CdTe heterojunction devices grown on bulk CdTe substrates in order to study the fundamental device physics of CdTe solar cells. Selection of emitter-layer alloys was based on passivation studies using double heterostructures as well as band alignment. Initial results show significant device integration challenges, including low dopant activation, high resistivity substrates and the development of low-resistance contacts. To date, the highest open-circuit voltage is 715 mV in a CdZnTe/CdTe heterojunction following anneal, while the highest fill factor of 52% was attained in an annealed CdTe homojunction. In general, all currentvoltage measurements show high series resistance, capacitancevoltages measurements show variable doping, and quantum efficiency measurements show low collection. Ongoing work includes overcoming the high resistance in these devices and addressing other possible device limitations such as non-optimum junction depth, interface recombination, and reduced bulk lifetime due to structural defects.
In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.
Increasing the power conversion efficiency of silicon (Si) photovoltaics is a key enabler for continued reductions in the cost of solar electricity. Here, we describe a two-terminal perovskite/Si tandem design that increases the Si cell’s output in the simplest possible manner: by placing a perovskite cell directly on top of the Si bottom cell. The advantageous omission of a conventional interlayer eliminates both optical losses and processing steps and is enabled by the low contact resistivity attainable between n-type TiO 2 and Si, established here using atomic layer deposition. We fabricated proof-of-concept perovskite/Si tandems on both homojunction and passivating contact heterojunction Si cells to demonstrate the broad applicability of the interlayer-free concept. Stabilized efficiencies of 22.9 and 24.1% were obtained for the homojunction and passivating contact heterojunction tandems, respectively, which could be readily improved by reducing optical losses elsewhere in the device. This work highlights the potential of emerging perovskite photovoltaics to enable low-cost, high-efficiency tandem devices through straightforward integration with commercially relevant Si solar cells.
Embodiments of the invention provide a method for direct heteroepitaxial growth of vertical III-V semiconductor nanowires on a silicon substrate. The silicon substrate is etched to substantially completely remove native oxide. It is promptly placed in a reaction chamber. The substrate is heated and maintained at a growth temperature. Group III-V precursors are flowed for a growth time. Preferred embodiment vertical Group III-V nanowires on silicon have a core-shell structure, which provides a radial homojunction or heterojunction. A doped nanowire core is surrounded by a shell with complementary doping. Such can provide high optical absorption due to the long optical path in the axial direction of the vertical nanowires, while reducing considerably the distance over which carriers must diffuse before being collected in the radial direction. Alloy composition can also be varied. Radial and axial homojunctions and heterojunctions can be realized. Embodiments provide for flexible Group III-V nanowire structures. An array of Group III-V nanowire structures is embedded in polymer. A fabrication method forms the vertical nanowires on a substrate, e.g., a silicon substrate. Preferably, the nanowires are formed by the preferred methods for fabrication of Group III-V nanowires on silicon. Devices can be formed with core/shell and core/multi-shell nanowires and the devices are released from the substrate upon which the nanowires were formed to create a flexible structure that includes an array of vertical nanowires embedded in polymer.
We present a novel, industrially relevant method to fabricate high-performance poly-Si passivating contacts for Si PV. Passivating contacts based on SiOx/poly-Si layer stacks have been implemented in record-efficiency homojunction Si solar cells. In this technology, the carrier transport through a surface-passivating SiOx is enabled either by quantum-tunneling or nanopinholes. The doped poly-Si layer provides charge-carrier selectivity. Previously, the ISFH research group demonstrated a record 26.1% efficient Si homojunction cell, where transport pinholes in ~2 nm SiOx were produced by thermal breakdown at > 1000 degrees C, which is hard to control and is surface morphology-dependent. At room temperature, our new process uses electroless plating of Ag nanoparticles, followed by metal-assisted chemical etching. Nanogalvanic corrosion yields < 20 nm-wide nanopinholes in an insulating > 2 nm SiOx layer. The nanopinholes are filled by a heavily doped a-Si:H overlayer. We drive in the dopants into the Si wafer with subsequent high-temperature annealing. Preferential incorporation of dopants at pinhole locations results in nanoscale p+/n or n+/n junctions near the wafer interface. Each heavily-doped nanoscale pinhole junction collects and transports photogenerated carriers to the cell metal contacts. The density of the engineered nanopinholes can be tuned over a wide range which is critical for optimization of device performance. The same nanogalvanic corrosion principles can be applied to produce doped transport pinholes in well-passivating thick dielectric SiOx/SiNy stacks. Importantly, our process does not rely on thermal breakdown of the dielectric layers and can be applied to textured wafers resulting in Si solar cells with > 20% conversion efficiency.
Here, we determined the electrical junction (EJ) locations in Cu(In,Ga)Se 2 (CIGS) and Cu 2 ZnSnSe 4 (CZTS) solar cells with ~20-nm accuracy by developing scanning capacitance spectroscopy (SCS) applicable to the thin-film devices. Cross-sectional sample preparation for the SCS measurement was developed by high-energy ion milling at room temperature for polishing the cross section to make it flat, followed by low-energy ion milling at liquid nitrogen temperature for removing the damaged layer and subsequent annealing for growing a native oxide layer. The SCS shows distinct p-type, transitional, and n-type spectra across the devices, and the spectral features change rapidly with location in the depletion region, which results in determining the EJ with ~20-nm resolution. We found an n-type CIGS in the region next to the CIGS/CdS interface; thus, the cell is a homojunction. The EJ is ~40 nm from the interface on the CIGS side. In contrast, such an n-type CZTS was not found in the CZTS/CdS cells. The EJ is ~20 nm from the CZTS/CdS interface, which is consistent with asymmetrical carrier concentrations of the p-CZTS and n-CdS in a heterojunction cell. Our results of unambiguously determination of the junction locations contribute significantly to understanding the large open-circuit voltage difference between CIGS and CZTS.
In the past ten years, there has been significant progress in solid-state optical refrigeration, causing a renewed interest in the possibility of electroluminescent cooling (ELC) in light emitting diodes (LEDs). More recently, our work on III-As based intracavity double diode structures (DDSs) indicates that the threshold for ELC can be reached, in practice, at high powers and 300 K if certain non-radiative recombination mechanisms and photodetector (PD) losses are minimized. The studied DDSs consist of a LED, incorporating a high-quality GaAs active layer, optically coupled to a GaAs p–n homojunction PD. Both the LED and PD are integrated in a single device, offering a unique environment for studying ELC. In this paper, we provide a brief overview of the DDS characteristics and investigate the impact of non-radiative interface recombination on the LED, showing how the choice of the barrier layer materials can suppress this effect. We use experimental characterization techniques to calibrate numerical simulations, coupling the drift-diffusion model for charge transport to a photon transport model. To explore the interface effects, we compare DDSs with either GaInP/GaAs or AlGaAs/GaAs double heterojunctions. The results suggest that GaInP barriers allow interface recombination suppression that is sufficient to reach internal cooling in the LED.
The performance of conventional p-type CdTe solar cells has plateaued in recent years, motivating exploration of n-type absorbers. Here, we evaluate a homojunction solar cell employing iodine-doped CdTe (CdTe:I) as the absorber in a Ti 3 C 2 T x MXene/p-CdTe:As/n-CdTe:I/indium structure through SCAPS-1D simulations and prototype devices. Optimized simulations predict efficiencies above 25% for thin CdTe:I absorbers (~0.7 μm). In contrast, the first prototype achieved only ~1.36% efficiency with V OC = 0.48 V, J SC = 6.45 mA/cm 2 and FF = 43.8%. When the simulation is adjusted to match the actual device structure, and the effective illumination is reduced to account for front-side light loss, the predicted V OC (0.48 V) and JSC (6.74 mA/cm 2 ) closely reproduce the experimental values. This suggests that the device performance is primarily limited by reduced front-side photon transmission and other material non-idealities. These results highlight the promise of iodine-doped n-type CdTe and identify clear pathways for further efficiency improvement.