Search NASA⌕ Search

SEARCH · Search NASA

Results for “IMPACT STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Impact and cratering processes on asteroids, satellites, and planets

A new model for scaling the outcome of catastrophic collisions from laboratory scale experiments was developed and applied to large bodies where gravitational binding is dominant. This algorithm includes a pressure dependent impact strength which predicts that large asteroids behave as intrinsically strong objects due to compressive loading of overburden throughout their interiors. For small bodies, where the gravitational loading is negligible, this model assumes that the impact strength is independent of size. There was considerable discussion of scaling laws for disruption when these results were presented to one authors colleagues. The pressure strengthening impact strength model was viewed as physically quite plausible; however, it was argued that the impact strength should decrease with increasing size in the size range where gravitational compression is negligible.

Chapman, Clark R.↗
NASA NTRS1978

Thermal environment effects on strength and impact properties of boron-aluminum composites

A systematic study was conducted regarding the degradation of fracture strength and impact energy in commercial B-Al composites in both static and cyclic thermal environments. The composites used in the study contained approximately 50 vol % boron fibers, unidirectionally aligned in either a 6061 Al or 1100 Al matrix. The tensile strengths of the composites after 3000 thermal cycles as a function of upper cycle temperature are presented in graphs. The temperature at which the strengths of 6061 Al matrix, B-Al composites were significantly degraded after 3000 cycles was noticeably higher than that for the 1100 Al matrix composites. Static heating at 420 C resulted in no significant strength degradation for the 6061 Al matrix composites. In the case of 1100 matrix composites, some degradation was observed at 420 C but markedly less than in the composites cycled to 420 C.

Grimes, H. H.↗
NASA NTRS1994

Coagulation of grains in static and collapsing protostellar clouds

We simulate collisional evolution of grains in dense turbulent molecular cloud cores (or Bok globules) in static equilibrium and free-fall collapse, assuming spherical symmetry. Relative velocities are due to thermal motions, differential settling, and turbulence, with the latter dominant for sonic turbulence with an assumed Kolmogorov spectrum. Realistic criteria are used to determine outcomes of collisions (coagulation vs. destruction) as functions of particle size and velocity. Results are presented for a variety of cloud parameters (radial density profile, turbulent velocity) and particle properties (density, impact strength). Results are sensitive to the assumed mechanical properties (density and impact strength) of grain aggregates. Particle growth is enhanced if aggregates have low density or fractal structures. On a timescale of a few Myr, an initial population of 0.1 micrometers grains may produce dense compact particles approximately 1 micrometer in size, or fluffy aggregates approximately 100 micrometers. For impact strengths less than or equal to 10(exp 6) ergs/g, a steady state is reached between coagulation of small grains and collisional disruption of larger aggregates. Formation of macroscopic aggregates requires high mechanical strengths and low aggregate densities. We assume sonic turbulence during collapse, with varied eddy size scales determining the dissipation rate or turbulence strength. The degree of collisional evolution during collapse is sensitive to the assumed small-scale structure (inner sc ale) of the turbulence. Weak turbulence results in few collisions and preserves the precollapse particle size distribution with little change. Strong turbulence tends to produce net destruction, rather than particle growth, during infall, unless inpact strengths are greater than 10(exp 6)ergs/g.

Weidenschilling, S. J.↗
NASA NTRS2018

The Adhesion Strength of Impact Ice Measured Using a Modified Lap Joint Test

Numerous methodologies have been utilized to measure the adhesion strength of impact ice, and the data reported in the literature varies significantly from test to test. In order to initiate an investigation to determine the cause of this disparity, a new test methodology has been developed and utilized in the Icing Research Tunnel at the NASA Glenn Research Center. Data was obtained while varying the temperature, test section velocity, and cloud droplet mean volumetric diameter. The first data set acquired using this new test method is presented. New trends demonstrate the effect of annealing ice samples, with temperature being a key variable. Observations during the test and analysis of the results suggest the presence of large residual stresses in the samples.

Work, Andrew H., Jr.↗
DOE OSTI2018

Effects of Natural and Artificial Weathering on the Physical Properties of Recycled Poly(ethylene terephthalate)

In accelerated weathering tests, specimens are exposed to higher radiation intensity, temperature and humidity than is likely under natural weathering in order to achieve rapid degradation of the polymer in a convenient short time. In the current work, a correlation between the two environments is attempted so that a prediction of lifetimes in the natural environment can be achieved. During aging, surface flaws are created due to the chain scission process. This is initiated by the absorption of ultra-violet light and directly affects visual appearance and impact strength. After natural weathering, the material shows only plastic deformation in an impact test. However, after artificial weathering to 5000 h of UV exposure, there is a decrease of 85% in impact strength. Colour change occurs at a high rate in the early stages of UV exposure. Beyond 2000 h of exposure, the colour change approaches a steady state and a correlation between the changes under natural and artificial weathering becomes apparent for a potential prediction of lifetimes. From the analysis including the specular component (SCI), taking surface roughening into account, 1 year under natural weathering was found to be equivalent to 25 days under accelerated weathering.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Material property characterization of 3D printed polypropylene wood plastic composites

Abstract Wood flour (WF) at 10 wt.% and 20 wt.% loadings was used as a reinforcing filler to enhance the applicability of polypropylene (PP) for 3D printing. After performing printability tests of PP wood plastic composites (WPCs), the mechanical properties of both injection‐molded and 3D‐printed PP WPC specimens were explored. Test specimens were prepared from 3D printed hexagons for analyzing the mechanical properties. Adding WF to neat PP increased the storage modulus and the glass transition temperature while decreasing the degree of crystallinity and the coefficient of thermal expansion, while enhancing the printability of neat PP. The tensile strength, tensile modulus of elasticity, flexural strength, and flexural modulus of elasticity of injection‐molded neat PP improved by up to 21%, 59%, 30%, and 56%, respectively, with 20 wt.% WF. However, the impact strength of injection‐molded neat PP decreased by 85%, with 20 wt.% WF. After 3D printing, the tensile strength and tensile modulus of elasticity of printed neat PP increased by up to 84% and 60%, respectively, with 20 wt.% WF. The flexural strength and flexural modulus of elasticity of neat printed PP remained unchanged compared to those of PP filled with 20 wt.% WF, while the impact strength decreased by 87%. Highlights WF was used as a reinforcement in polypropylene designed for 3D printing A pilot‐scale, pellet‐fed 3D printer was used to print hollow hexagons, and then test specimens were fabricated from these hexagons for mechanical properties The tensile and flexural properties of 3D printed neat polypropylene improved, while the impact strength decreased after adding 20 wt.% WF to the neat PP.

Hwang, Sungjun↗
NASA NTRS1987

Effective collision strengths for electron impact excitations in S II

Electron impact collision strengths for forbidden, semiforbidden, and allowed transitions in S II calculated using the R-matrix method are presented. Configuration interaction wave functions are used to represent the six target states included in the calculation. At low impact energies the collision strengths are dominated by resonances for several transitions. The contribution from higher partial waves is obtained in the close-coupling approximation with exchange terms omitted. Results are presented for the effective collision strengths over a wide temperature range (5000-150,000 K) of astrophysical interest. The present results for the 4S(0) yields 2P(0) transition are 20-30 percent lower than previous calculations, while for the 4S(0) yields 2D(0) transition they are in good agreement. The results are approximately 30 percent higher than those of Ho and Henry (1983) for the 4S(0) yields 2P(0) transition at 80,000 K, and the difference between the two results increases with decreasing temperatures (under 80,000 K).

Tayal, S. S.↗
NASA NTRS1972

Pendulum impact resistance of tungsten fiber/metal matrix composites.

The impact properties of copper, copper-10 nickel, and a superalloy matrix reinforced with tungsten fibers were studied. In most cases the following increased composite impact strength: increased fiber or matrix toughness, decreased fiber-matrix reaction, increased test temperature, hot working and heat treatment. Notch sensitivity was reduced by increasing fiber or matrix toughness. The effect of fiber content depended on the relative toughness of the fibers and matrix. Above 530 K a 60 volume per cent superalloy matrix composite had a greater impact strength than a turbine blade superalloy, whereas below 530 K a hot worked 56 volume per cent composite had a greater impact strength than the superalloy.

Winsa, E. A.↗
NASA NTRS1990

On collisional disruption - Experimental results and scaling laws

Both homogeneous and inhomogeneous targets have been addressed by the present experimental consideration of the impact strengths, fragment sizes, and fragment velocities generated by cement mortar targets whose crushing strengths vary by an order of magnitude, upon impact of projectiles in the velocity range of 50-5700 m/sec. When combined with additional published data, dynamic impact strength is found to correlate with quasi-static material strengths for materials ranging in character from basalt to ice; two materials not following this trend, however, are weak mortar and clay targets. Values consistent with experimental results are obtainable with a simple scaling algorithm based on impact energy, material properties, and collisional strain rate.

Davis, Donald R.↗
DOE OSTI2018

Chemically Functionalized Plant Fibers and Carbon Nanotubes for High Compatibility and Reinforcement in Polylactic Acid (PLA) Composite

In this study, surface modification is used to improve the compatibility of Kenaf fibers (KFs) and multi-walled carbon nanotubes (MWCNTs) in a polylactic acid (PLA) matrix, as well as to enhance the mechanical properties. Through the use of a silane coupling agent, the KF is grafted with functional groups to generate a chemical bond with the PLA; the modified KF shows high compatibility in the PLA matrix. Compared to the bare PLA, the optimal KF/MWCNT/PLA composite (PC1F30-OX) shows increases of 58% in tensile strength, and 113% in impact strength. A small addition of MWCNTs (1 wt%) dramatically improves the antistatic ability by lowering the surface resistance to 3.47 GΩ. With the addition of hydrophilic KF into the PLA, the composite becomes much more environmentally friendly, and the biodegradation rate can be controlled by the amount of KF added. The addition of hydrophilic KF allowed the composite to accommodate more enzyme to hasten the biodegradation; almost complete decomposition occurred after 11 weeks.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2018

Performance of Cow Dung Reinforced Biodegradable Poly(Lactic Acid) Biocomposites for Structural Applications

In this work, performance of cow dung (CD) reinforced poly(lactic acid) (PLA) biocomposites was investigated for the potential use in load bearing application. CD of average 4 mm size was blended with PLA at different CD ratios (0–50 wt%) and their effects on the biocomposite properties were studied. The results showed an improvement in the flexural properties, while the tensile and impact strength dropped by 20 and 28% with the addition of 50% CD. The decline in the tensile and impact strength was due to micro-cracking and voids formation at higher CD content. Also, the incorporation of CD slightly decreased the thermal stability of the biocomposite. However, dynamic mechanical properties of the biocomposites generally improved. SEM analysis of tensile and impact fractured surfaces indicated that the CD had a reasonable adhesion with matrix. Moreover, the SEM micrographs of soil burial studies showed an accelerated degradation of higher CD wt% biocomposites.

36 MATERIALS SCIENCE↗
NASA NTRS2009

Developing a Material Strength Design Value Based on Compression after Impact Damage for the Ares I Composite Interstage

The derivation of design values for compression after impact strength for two types of honeycomb sandwich structures are presented. The sandwich structures in this study had an aluminum core and composite laminate facesheets of either 16-ply quasi or 18-ply directional lay-ups. The results show that a simple power law curve fit to the data can be used to create A- and B-basis residual strength curves.

Nettles, A. T.↗
DOE OSTI2019

Study on Mechanical and Thermal Properties of Poly(Lactic acid)/Poly(Butylene adipate-co-terephthalate)/Office Wastepaper Fiber Biodegradable Composites

Office wastepaper fibers(OWF)/poly(butylene adipate-co-terephthalate) (PBAT)/poly(lactic acid) (PLA) biodegradable composites with different mass ratio were made by melt blending and injection moulding process. At the same time, the use of MAPLA and KH560 was studied as a potential approach for improving interfacial adhesion between OWF, PBAT and PLA. The results revealed that with the increasing of PBAT, the notched impact strength of PLA/PBAT/OWF composites can be first increased and then decreased. When the content of PBAT was 20 wt%, the notch impact strength of PLA/PBAT/OWF composite was the highest, increased by 291% compared with pure PLA. TGA results revealed that the onset degradation temperature of the composites can be increased and its thermal decomposition step can be changed. According to the crystallization and melting performance table, OWF can act as nucleating agent to promote the crystallization properties of composites, while PBAT can prevent the crystallization and the higher the content is, the more obvious it is. It can be seen from the SEM figures that the addition of MAPLA and KH560 simultaneously makes the composites interface bond closer, thus improving the interface performance of PLA/20PBAT/OWF composite. Among the three kinds of modified composites, PLA/20PBAT/OWF/MK composite has the lowest water absorption and the best comprehensive performance.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Polymeric materials from renewable resources

The goals of our studies have been the use of renewable raw materials in the preparation of polymeric materials with diversified properties. In this context, lignosulfonate, which is produced in large scale around the world, but not widely used in the production of polymeric materials, was used to replace phenol and polyols in the preparation of phenolic- (Ligno-PH) and polyurethane-type (Ligno-PU) polymers, respectively. These polymers were used to prepare composites reinforced with sisal lignocellulosic fibers. The use of lignosulfonate in the formulation of both types of polymers was beneficial, because in general composites with improved properties, specially impact strength, were obtained. Composites were also prepared from the so called “biopolyethylene” (HDPE), curaua lignocellulosic fiber, and castor oil (CO). All composites HDBPE/CO/Fiber exhibited higher impact strength, when compared to those of the corresponding HDBPE/Fiber. These results, combined with others (eg SEM images of the fractured surfaces) indicated that, in addition to acting as a plasticizer, this oil may have acted as a compatibilizer of the hydrophilic fiber with the hydrophobic polymer. The set of results indicated that (i) mats with nano (diameter ≤ 100nm) and/or ultrafine (submicron scale) fibers were produced, (ii) hybrid fibers were produced (bio-based mats composites), (iii) cellulosic pulp (CP) and/or lignin (Lig) can be combined with PET matrices to control properties such as stiffness and hydrophilicity of the respective mats. Materials with diversified properties were prepared from high content of renewable raw materials, thus fulfilling the proposed targets.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Thermal stability and aging of some new anaerobic adhesives for structural binding

Polyurethane-modified high impact anaerobic adhesives have been chosen for a bonding application where impact cushion is critical. These adhesives meet all the requirements for high rate production and automatic assembly techniques. With aluminum adherends, one selected adhesive cured at room temperature with the recommended activator retained sixty percent of its original impact strength after twenty-six week aging at 100 C. The impact strength aging, the thermogravimetric analysis results, the outgassing data, and other observations made in this work indicate that the adhesives cured by simple heating give a more durable bond than that cured with an activator at room temperature.

Lee, S. Y.↗
NASA NTRSDate not supplied

A Statistical Analysis of Impact Ice Adhesion Strength Data Acquired with a Modified Lap Joint Test

Numerous methodologies have been utilized to measure the adhesion strength of impact ice, and the data reported in the literature varies significantly from method to method. In order to initiate an investigation to determine the cause of this disparity, a lap-joint shear test methodology that was recently developed was utilized in the Icing Research Tunnel at the NASA Glenn Research Center. Data was obtained while varying the temperature, test section velocity, liquid water content, and cloud droplet median volumetric diameter, among other parameters, over five campaigns. A new data set acquired using this new test method is presented. The results are analyzed with standard statistical methodologies and demonstrate a strong correlation between the apparent adhesion strength of ice and temperature, annealing time, and heating time. Observations during the test and analysis of the results suggest the presence of large residual stresses in the samples, which is in agreement with prior work. Due to the nature of the test methodology, and all known ice adhesion test methodologies, the measured, or apparent, adhesion strength is geometry dependent, a fact emphasized by the results presented here. The data was organized both cumulatively and independently by result code. Trends in the data are discussed in the context of causal physical mechanisms. The data shows the apparent adhesion strength was not linear with temperature, liquid water content, annealing time, and other variables. Short-term heating of the samples was shown to have negligible effect, and the apparent adhesion strength had a flat trend with velocity.

Ice Adhesion↗
DOE OSTI2016

Thermal and mechanical properties of TPU/PBT reinforced by carbon fiber

In this study, thermal, mechanical properties and processability were performed on a series of carbon fiber (CF) filled thermoplastic polyurethane (TPU)/poly (butylene terephthalate) (PBT) composites to identify the effect of CF weight fraction on the properties of TPU/PBT. Scanning Electronic Microscope (SEM) show that CFs are uniformly dispersed in TPU/PBT matrix and there are no agglomerations. Melt flow index (MFI) show that the melt viscosity increased with the CF loading. Thermogravimetric analysis (TGA) revealed that the introduction of CF into organic materials tend to improve their thermal stability. The mechanical properties indicated that tensile strength and modulus, flexural strength and modulus, improved with an increase in CF loading, but the impact strength decreased by the loading of CF.

36 MATERIALS SCIENCE↗