SEARCH · Search NASA

Results for “INTERFERENCE - PROPELLER BLADES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS2002

Methodology of Blade Unsteady Pressure Measurement in the NASA Transonic Flutter Cascade

In this report the methodology adopted to measure unsteady pressures on blade surfaces in the NASA Transonic Flutter Cascade under conditions of simulated blade flutter is described. The previous work done in this cascade reported that the oscillating cascade produced waves, which for some interblade phase angles reflected off the wind tunnel walls back into the cascade, interfered with the cascade unsteady aerodynamics, and contaminated the acquired data. To alleviate the problems with data contamination due to the back wall interference, a method of influence coefficients was selected for the future unsteady work in this cascade. In this approach only one blade in the cascade is oscillated at a time. The majority of the report is concerned with the experimental technique used and the experimental data generated in the facility. The report presents a list of all test conditions for the small amplitude of blade oscillations, and shows examples of some of the results achieved. The report does not discuss data analysis procedures like ensemble averaging, frequency analysis, and unsteady blade loading diagrams reconstructed using the influence coefficient method. Finally, the report presents the lessons learned from this phase of the experimental effort, and suggests the improvements and directions of the experimental work for tests to be carried out for large oscillation amplitudes.

Lepicovsky, J.↗

NASA NTRS1977

Theoretical study of the effect of ground proximity on the induced efficiency of helicopter rotors

A study of rotors in forward flight within ground effect showed that the ground-induced interference is an upwash and a decrease in forward velocity. The interference velocities are large, oppose the normal flow through the rotor, and have large effects on the induced efficiency. Hovering with small ground clearances may result in significant blade stall. As speed is increased from hover in ground effect, power initially increases rather than decreases. At very low heights above the ground, the power requirements become nonlinear with speed as a result of the streamwise interference. The streamwise interference becomes greater as the wake approaches the ground and eventually distorts the wake to form the ground vortex which contributes to certain observed directional stability problems.

Heyson, H. H.↗

NASA NTRS1974

Experimental investigation of model variable-geometry and ogee tip rotors

An experimental investigation was conducted to systematically explore the effects of inter-blade spatial relationships and pitch variations on rotor performance and wake geometry. Variable-geometry rotors consisting of various combinations of blade length, axial spacing, azimuth spacing, and collective pitch were tested at model scale in hover and forward flight. In addition, a hover test of a model rotor with an ogee blade tip design was conducted to determine its performance and wake characteristics. The results of this investigation indicate that properly selected variable geometry rotor configurations can offer substantial improvements in hover performance without adversely affecting forward flight performance. Axial spacing of alternate blades was found to provide the greatest performance benefit, and further improvements were achieved by combining azimuth spacing with axial spacing. The performance benefit appears to be related to the relief of local adverse aerodynamic phenomena produced by vortex interference. The ogee tip design was found to substantially reduce the concentrated core intensity of the tip vortex, and could thus prove beneficial for the relief of blade-vortex interaction problems. However, the ogee tip was found to reduce hover performance at model scale.

Landgrebe, A. J.↗

NASA NTRS2010

Augmented Adaptive Control of a Wind Turbine in the Presence of Structural Modes

Wind turbines operate in highly turbulent environments resulting in aerodynamic loads that can easily excite turbine structural modes, potentially causing component fatigue and failure. Two key technology drivers for turbine manufacturers are increasing turbine up time and reducing maintenance costs. Since the trend in wind turbine design is towards larger, more flexible turbines with lower frequency structural modes, manufacturers will want to develop methods to operate in the presence of these modes. Accurate models of the dynamic characteristics of new wind turbines are often not available due to the complexity and expense of the modeling task, making wind turbines ideally suited to adaptive control. In this paper, we develop theory for adaptive control with rejection of disturbances in the presence of modes that inhibit the controller. We use this method to design an adaptive collective pitch controller for a high-fidelity simulation of a utility-scale, variable-speed wind turbine operating in Region 3. The objective of the adaptive pitch controller is to regulate generator speed, accommodate wind gusts, and reduce the interference of certain structural modes in feedback. The control objective is accomplished by collectively pitching the turbine blades. The adaptive pitch controller for Region 3 is compared in simulations with a baseline classical Proportional Integrator (PI) collective pitch controller.

Frost, Susan A.↗

NASA NTRSDate not supplied

Rotor Performance Predictions of a Next Generation Mars Science Helicopter

Since Ingenuity took flight and proved aerial capabilities on Mars, the horizon for rotorcraft on the Red Planet has only expanded. One proposed future Martian rotorcraft is the Mars Science Helicopter (MSH). The MSH is a hexacopter capable of carrying scientific payloads. As a part of its joint development by NASA Ames Research Center (ARC) and the Jet Propulsion Laboratory (JPL), key MSH rotor components will be tested inside the in-development Reduced Atmospheric Pressure Testing Of Rotors (RAPTOR) wind tunnel in the Planetary Aeolian Laboratory (PAL) at NASA ARC. In preparation for the test, the Comprehensive Hierarchical Aeromechanics Rotorcraft Model (CHARM) analysis was utilized to predict the aerodynamic performance for one MSH hexacopter isolated rotor. This paper provides an overview of the planned experiments involving the MSH reference blades, as well as CHARM pretest predictions of rotor performance in hover and forward flight. Additionally, the interference effects of wind tunnel walls on rotor performance will be evaluated to inform the test matrix of the upcoming test in the RAPTOR tunnel.

MHS↗

NASA NTRS1991

Rotorcraft application of advanced computational aerodynamics

The objective was to develop the capability to compute the unsteady viscous flow around rotor-body combinations. In the interest of tractability, the problem was divided into subprograms for: (1) computing the flow around a rotor blade in isolation; (2) computing the flow around a fuselage in isolation, and (3) integrating the pieces. Considerable progress has already been made by others toward computing the rotor in isolation (Srinivasen) and this work focused on the remaining tasks. These tasks required formulating a multi-block strategy for combining rotating blades and nonrotating components (i.e., a fuselage). Then an appropriate configuration was chosen for which suitable rotor body interference test data exists. Next, surface and volume grids were generated and state-of-the-art CFD codes were modified and applied to the problem.

Stanaway, Sharon↗

NASA NTRS1984

Hovering model helicopter rotor testing

A relatively large test chamber, chosen to minimize room interference effects during helicopter hovering rotor tests, was found in initial operations to exhibit large, random variations of thrust, torque, and blade flapping. The source of these problems, unsteady recirculation of test chamber flow, was addressed by the addition of a 'flow straightener' that reduced these parameter variations to 1.5 percent of mean values. Rotor performance was then measured outside the chamber in calm, free air conditions and compared with chamber results obtained before and after modifications. Attention is given to wake flow visualization conducted in the test chamber, as well as outside.

Piziali, R. A.↗

NASA NTRS2015

Wind Tunnel Interference Effects on Tilt Rotor Testing Using Computational Fluid Dynamics

Experimental techniques to measure rotorcraft aerodynamic performance are widely used. However, most of them are either unable to capture interference effects from bodies, or require an extremely large computational budget. The objective of the present research is to develop an XV-15 Tilt Rotor Research Aircraft rotor model for investigation of wind tunnel wall interference using a novel Computational Fluid Dynamics (CFD) solver for rotorcraft, RotCFD. In RotCFD, a mid-fidelity URANS solver is used with an incompressible flow model and a realizable k-ε turbulence model. The rotor is, however, not modeled using a computationally expensive, unsteady viscous body-fitted grid, but is instead modeled using a blade element model with a momentum source approach. Various flight modes of the XV-15 isolated rotor, including hover, tilt and airplane mode, have been simulated and correlated to existing experimental and theoretical data. The rotor model is subsequently used for wind tunnel wall interference simulations in the National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames Research Center in California. The results from the validation of the isolated rotor performance showed good correlation with experimental and theoretical data. The results were on par with known theoretical analyses. In RotCFD the setup, grid generation and running of cases is faster than many CFD codes, which makes it a useful engineering tool. Performance predictions need not be as accurate as high-fidelity CFD codes, as long as wall effects can be properly simulated. For both test sections of the NFAC wall interference was examined by simulating the XV-15 rotor in the test section of the wind tunnel and with an identical grid but extended boundaries in free field. Both cases were also examined with an isolated rotor or with the rotor mounted on the modeled geometry of the Tiltrotor Test Rig (TTR). A 'quasi linear trim' was used to trim the thrust for the rotor to compare the power as a unique variable. Power differences between free field and wind tunnel cases were found from -7 % to 0 % in the 80- by 120-Foot Wind Tunnel test section and -1.6 % to 4.8 % in the 40- by 80-Foot Wind Tunnel, depending on the TTR orientation, tunnel velocity and blade setting. The TTR will be used in 2016 to test the Bell 609 rotor in a similar fashion to the research in this report.

CFD↗

NASA NTRS1988

SSME single-crystal turbine blade dynamics

A study was performrd to determine the dynamic characteristics of the Space Shuttle Main Engine high pressure fuel turbopump (HPFTP) blades made of single crystal (SC) material. The first and second stage drive turbine blades of HPFTP were examined. The nonrotating natural frequencies were determined experimentally and analytically. The experimental results of the SC second stage blade were used to verify the analytical procedures. The study examined the SC first stage blade natural frequencies with respect to crystal orientation at typical operating conditions. The SC blade dynamic response was predicted to be less than the directionally solidified base. Crystal axis orientation optimization indicated that the third mode interference will exist in any SC orientation.

Moss, Larry A.↗

NASA NTRS2015

Fuselage-Induced Velocity Model for LRTA, RTA, and HART Fuselages

In order to make the aerodynamic fuselage-rotor interference effects available to comprehensive rotor codes, a simple analytical model of the fuselage-induced velocities within the volume of rotor blade operation above the fuselage is developed here for the following bodies used in wind tunnel experiments: the Large Rotor Test Apparatus (LRTA), the Rotor Test Apparatus (RTA), and the Higher Harmonic Control Aeroacoustic Rotor Test (HART).While the first two are used in the National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames, California, the third one is used by DLR in the large low-speed facility of the German-Dutch wind tunnel in the Netherlands. The fuselage-induced velocity model is based on parameter identification of isolated fuselage-induced velocity data (computed by means of computational fluid dynamics, CFD) and is intended to be generic enough to be used for real helicopter fuselages as well. The accuracies obtained in reproducing the CFD data show a remaining average error of less or equal 5 of the peak-to-peak induced velocity range, which is considered sufficient for comprehensive code analysis.

HART↗

NASA NTRS1947

Laboratory Report on the Investigation of the Flow around Two Turbine-Blade Profiles using the Interferometer Method

At the request of the Junkers Aircraft and Engine Construction Company, Engine Division, Dessau Main Plant, an investigation was made using the interferometer method on the two turbine-blade profiles submitted. The interferometer method enables making visible the differences in density and consequently the boundary layers that develop when a flow is directed on the profile. Recognition of the points on the profile at which separation of flow occurs is thus possible. By means of the interference photographs the extent of the dead-water region may be ascertained. The size of the dead-water region provides evidence as to the quality of the flow and allows a qualitative estimate of the amount of the flow losses. Interference photographs thus provide means of judging the utility of profiles under specific operating conditions and provide suggestions for possible changes of profile contours that might help to improve flow relations. Conclusions may be drawn concerning the influence of the blade-spacing ratio, the inlet-air angle, and the connection between the curvature of the profile contour and the point of separation of the flow from the profile surface.

vonVietinghoff-Scheel, K.↗

NASA NTRS1985

Study for prediction of rotor/wake/fuselage interference, part 1

A method was developed which allows the fully coupled calculation of fuselage and rotor airloads for typical helicopter configurations in forward flight. To do this, an iterative solution is carried out based on a conventional panel representation of the fuselage and a blade element representation of the rotor where fuselage and rotor singularity strengths are determined simultaneously at each step and the rotor wake is allowed to relax (deform) in response to changes in rotor wake loading and fuselage presence. On completion of the iteration, rotor loading and inflow, fuselage singularity strength (and, hence, pressure and velocity distributions) and rotor wake are all consistent. The results of a fully coupled calculation of the flow around representative helicopter configurations are presented. The effect of fuselage components on the rotor flow field and the overall wake structure is detailed and the aerodynamic interference between the different parts of the aircraft is discussed.

Clark, D. R.↗

NASA NTRS2016

Wind Tunnel Interference Effects on Tilt Rotor Testing Using Computational Fluid Dynamics

Experimental techniques to measure rotorcraft aerodynamic performance are widely used. However, most of them are either unable to capture interference effects from bodies, or require an extremely large computational budget. The objective of the present research is to develop an XV-15 Tiltrotor Research Aircraft rotor model for investigation of wind tunnel wall interference using a novel Computational Fluid Dynamics (CFD) solver for rotorcraft, RotCFD. In RotCFD, a mid-fidelity Unsteady Reynolds Averaged Navier-Stokes (URANS) solver is used with an incompressible flow model and a realizable k-ε turbulence model. The rotor is, however, not modeled using a computationally expensive, unsteady viscous body-fitted grid, but is instead modeled using a blade-element model (BEM) with a momentum source approach. Various flight modes of the XV-15 isolated rotor, including hover, tilt, and airplane mode, have been simulated and correlated to existing experimental and theoretical data. The rotor model is subsequently used for wind tunnel wall interference simulations in the National Full-Scale Aerodynamics Complex (NFAC) at Ames Research Center in California. The results from the validation of the isolated rotor performance showed good correlation with experimental and theoretical data. The results were on par with known theoretical analyses. In RotCFD the setup, grid generation, and running of cases is faster than many CFD codes, which makes it a useful engineering tool. Performance predictions need not be as accurate as high-fidelity CFD codes, as long as wall effects can be properly simulated. For both test sections of the NFAC wall, interference was examined by simulating the XV-15 rotor in the test section of the wind tunnel and with an identical grid but extended boundaries in free field. Both cases were also examined with an isolated rotor or with the rotor mounted on the modeled geometry of the Tiltrotor Test Rig (TTR). A "quasi linear trim" was used to trim the thrust for the rotor to compare the power as a unique variable. Power differences between free field and wind tunnel cases were found from -7 to 0 percent in the 80- by 120-Foot Wind Tunnel and -1.6 to 4.8 percent in the 40- by 80-Foot Wind Tunnel, depending on the TTR orientation, tunnel velocity, and blade setting. The TTR will be used in 2016 to test the Bell 609 rotor in a similar fashion to the research in this report.

CFD↗

NASA NTRS1985

Study for prediction of rotor/wake/fuselage interference. Part 2: Program users guide

A method was developed which permits the fully coupled calculation of fuselage and rotor airloads for typical helicopter configurations in forward flight. To do this, an iterative solution is carried out based on a conventional panel representation of the fuselage and a blade element representation of the rotor where fuselage and rotor singularity strengths are determined simultaneously at each step and the rotor wake is allowed to relax (deform) in response to changes in rotor wake loading and fuselage presence. On completion of the iteration, rotor loading and inflow, fuselage singularity strength (and, hence, pressure and velocity distributions) and rotor wake are all consistent. The results of a fully coupled calculation of the flow around representative helicopter configurations are presented. The effect of fuselage components on the rotor flow field and the overall wake structure is discussed as well as the aerodynamic interference between the different parts of the aircraft. Details of the computer program are given.

Clark, D. R.↗

NASA NTRS1977

Study of noise and inflow distortion sources in the NASA QF-1B fan using measured blade and vane pressures

Pressure transducers were installed on the blades and vanes of QF-1B, a transonic-tip-speed fan from the NASA Quiet Fan Program which was tested on the outdoor quiet fan test facility at NASA-Lewis. Signals from the transducers and from far field microphones were analyzed to determine sources of nonuniform inflow and noise. The nonuniform inflow was mostly unsteady with roughly equal contributions from atmospheric turbulence and rig interference. The rig interference was largest at the bottom and appeared to be generated by the support structure which was located behind the inlet lip under the fan. Interaction of this inflow distortion was the dominant source of noise at 1, 2, and 3 times blade passing frequency (BPF) at 60, 70, and 80 percent of design speed. At 90 percent speed, noise at BPF was dominated by the steady rotor field. A broadband spectrum peak centered at about 2.2 times BPF was identified as rotor/stator interaction stemming from a high frequency rotor exit flow component. The remaining broadband energy from 0.3 to 3.5 times BPF was attributed to the better known type of rotor/stator interaction associated with rotor wake turbulence.

Hanson, D. B.↗

NASA NTRS1955

Effect of Reduced Stator-blade Trailing-edge Thickness on Over-all Performance of a Transonic Turbine

A transonic turbine with a stator trailing-edge thickness reduced from 0.030 to 0.010 inch has been investigated experimentally. The performance results indicated an increase in efficiency of 0.6 of a point at design operation, and as much as 2.4 points at off-design conditions, as a result of reducing the trailing-edge thickness. This improvement could only be partially accounted for by the theoretical change in mixing loss for the two stator-blade rows, and it was felt that the improvement was largely due to a reduced amount of low-velocity fluids entering the rotor and the interference effect of these fluids whth the mainstream flow.

Whitney, Warren J↗

NASA NTRS1976

An investigation of possible causes for the reduction of fan noise in flight

An experimental investigation of the impact on fan tone-noise generation of several engine inflow distortions found in conventional static testing has been made. Inflow distortions examined included the ground vortex, atmospheric turbulence, and test-stand structure interference. This work was undertaken to help explain results from noise measurements made on modern turbofan engines which show lower fan tone levels in flight at the blade-passing frequency than are predicted from static measurements. The results indicate that the ground vortex can greatly increase noise at the blade-passing frequency. A special inlet was designed to examine the effects of atmospheric turbulence. Use of this inlet reduced the variability of the sound-pressure level at the blade-passing frequency, and the results were similar to those found in flight.

Hodder, B. K.↗

NASA NTRS1983

Special opportunities in helicopter aerodynamics

Aerodynamic research relating to modern helicopters includes the study of three dimensional, unsteady, nonlinear flow fields. A selective review is made of some of the phenomenon that hamper the development of satisfactory engineering prediction techniques, but which provides a rich source of research opportunities: flow separations, compressibility effects, complex vortical wakes, and aerodynamic interference between components. Several examples of work in progress are given, including dynamic stall alleviation, the development of computational methods for transonic flow, rotor-wake predictions, and blade-vortex interactions.

Mccroskey, W. J.↗