Search NASA⌕ Search

SEARCH · Search NASA

Results for “Interference Effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Interference effects on the hypersonic, rarefied flow about a flat plate

The Direct Simulatiaon Monte Carlo method is used to study the hypersonic, rarefied flow interference effects on a flat plate caused by nearby surfaces. Calculations focus on shock-boundary-layer and shock-lip interactions in hypersonic inlets. Results are presented for geometries consisting of a flat plate with different leading-edge shapes over a flat lower wall and a blunt-edge flat plate over a 5-degree wedge. The problems simulated correspond to a typical entry flight condition of 7.5 km/s at altitudes of 75 to 90 km. The results show increases in predicted local heating rates for shock-boundary-layer and shock-lip interactions that are quantitatively similar to those observed experimentally at much higher densities.

Wilmoth, Richard G.↗
NASA NTRS1931

Interference Effects and Drag of Struts on a Monoplane Wing

Tests were conducted in the Variable Density Wind Tunnel of the NACA to determine the importance of the interference effects and drag of struts on a monoplane. Inclined struts were placed upon a Gottingen 387 airfoil in the lower surface positions and in two upper surface positions. Tests were made at values of Reynolds Number comparable with those obtained in flight. It was found that the interference drag of struts may be as great as the drag of the struts alone.

Ward, Kenneth E↗
NASA NTRS1983

Interference effects of aft reaction-control yaw jets on the aerodynamic characteristics of a space shuttle orbiter model at supersonic speeds

A wind tunnel investigation of the interference effects of aft reaction control system yaw jet plumes on a 0.0125 scale Space Shuttle orbiter model was conducted at Mach numbers from 2.50 to 4.50. Test variables included model angle of attack, model angle of sideslip, jet to free stream mass flow ratio, and number and position of operating jets. The aft reaction control jet plume creates a blockage above and behind the wing on the side in which the jet exhausts and results in flow separation on the wing upper surface and fuselage side. Positive pitching moment and side force increments and negative yawing moment and rolling moment increments due to the flow separations are incurred for left side firing jets, primarily at angles of attack above 10 deg. The yawing moment interference increments are favorable and result in a small jet thrust amplification. As a result of this investigation, the aft reaction control system was certified for operation at supersonic Mach numbers prior to the first flight of the space transportation system (STS-1).

Covell, P. F.↗
NASA NTRS1974

Aerodynamic results of a support system interference effects test conducted at NASA/LaRC UPWT using an 0.015-scale model of the configuration 140A/B SSV orbiter (0A20B)

An experimental aerodynamic investigation was conducted to determine the interference effects of a wind tunnel support system. The test article was a 0.015 scale model of the space shuttle orbiter. The primary objective of the test was to determine the extent that aerodynamic simulation of the space shuttle orbiter is affected by base mounting the model, without nozzles, on a straight sting. Two support systems were tested. The characteristics of the support systems are described. Data from the tests are presented in the form of graphs and tables.

Campbell, J. H., II↗
NASA NTRS1984

Interference effects of thrust reversing on horizontal tail effectiveness of twin-engine fighter aircraft at Mach numbers from 0.15 to 0.90

An investigation was conducted in the Langley 16 foot Transonic Tunnel to determine the interference effects of thrust reversing on horizontal tail effectiveness of a twin engine, general research fighter model at approach and in-flight speeds. Twin vertical tails at three longitudinal locations were tested at a cant angle of 0 deg. One configuration was also tested at a cant angle of 20 deg. Two nonaxisymmetric nozzle reverser concepts were studied. Test data were obtained at Mach numbers of 0.15, 0.60, and 0.90 and at angles of attack from -3 to 9 deg. Nozzle pressure ratios varied from jet off to 7.0, depending upon Mach number. At landing approach speed (Mach number 0.15), thrust reverser operation usually resulted in large variations (up to 70% increase) in horizontal tail effectiveness as nozzle pressure ratio was varied at zero angle of attack or as angle of attack was varied at constant nozzle pressure ratio. There was always a decrease in effectiveness at Mach numbers of 0.60 and 0.90 as a result of reverser operation.

Capone, F. J.↗
NASA NTRS1983

A lifting surface computer code with jet-in-crossflow interference effects. Volume 1: Theoretical description

A method is proposed to combine a numerical description of a jet in a crossflow with a lifting surface panel code to calculate the jet/aerodynamic-surface interference effects on a V/STOL aircraft. An iterative technique is suggested that starts with a model for the properties of a jet/flat plate configuration and modifies these properties based on the flow field calculated for the configuration of interest. The method would estimate the pressures, forces, and moments on an aircraft out of ground effect. A first-order approximation to the method suggested is developed and applied to two simple configurations. The first-order approximation is a noniterative precedure which does not allow for interactions between multiple jets in a crossflow and also does not account for the influence of lifting surfaces on the jet properties. The jet/flat plate model utilized in the examples presented is restricted to a uniform round jet injected perpendicularly into a uniform crossflow for a range of jet-to-crossflow velocity ratios from three to ten.

Furlong, K. L.↗
NASA NTRS1990

Interference effects on Space Station Freedom and Space Shuttle Orbiter Ku-band single access return links

In a Ku-band single access return (KSAR) communication link via the tracking and data relay satellite system (TDRSS), the interference between spacecraft can be discriminated by opposite antenna polarizations, pseudo-noise code, and by TDRSS antenna beam pointing. For the Space Station Freedom (SSF) KSAR and the Space Shuttle Orbiter (SSO) KSAR links, the pseudo-noise coding technique is not exploited. In addition, the two KSAR links use the same carrier frequency. Therefore, if the SSF and SSO are in close proximity, it is expected that mutual interference will be significant. Mutual interference effects on the SSO-KSAR I-channel and the SSF-KSAR links are analytically derived and compared to the simulation results. For the analysis, the channel is assumed ideally bandlimited and linear. It is demonstrated that a simplified (linear bandlimited channel) analytical approach yields results of adequate accuracy in an estimation of the signal degradation by interference.

Kwon, Hyuck M.↗
NASA NTRS1962

Jet Interference Effects on a Model of a Single-Engine Four Jet V/STOL Airplane at Mach Numbers from 0.60 to 1.00

An investigation was conducted in the Langley 16-foot transonic tunnel to determine the interference from four exhaust jets on the aerodynamic characteristics of a model of a V/STOL airplane. The single- engine four-jet turbofan power plant of the airplane was simulated by inducing tunnel airflow through two large side inlets and injecting the decomposition products of hydrogen peroxide into the internal flow. The heated gas mixture was exhausted through four nozzles located on the sides of the fuselage under the wing, two near the wing leading edge and two forward of the trailing edge; the nozzles were deflected downward 1.5 deg and outward 5.0 deg to simulate cruise conditions. The wing of the model was a clipped delta with leading-edge sweep of 40 deg, aspect ratio of 3.06, taper ratio of 0.218, thickness-chord ratio of 0.09 at the root and 0.07 at the tip, and 10 deg negative dihedral. Aerodynamic and longitudinal stability coefficients were obtained for the model with the tail removed, and for horizontal-tail incidences of 0 deg and -5 deg. Data were obtained at Mach numbers from 0.60 to 1.00, angles of attack from 0 deg to 12 deg, and with jet total-pressure ratios up to 3.1. Jet operation generally caused a decrease in lift, an increase in pitching-moment coefficient, and a decrease in longitudinal stability at subsonic speeds. The jet interference effects on drag were detrimental at a Mach number of 0.60 and favorable at higher speeds for cruising-flight attitudes.

Schmeer, James W.↗
NASA NTRS1982

Experimental determination of flow-interference effects of wing-mounted, two-dimensional, full-capture propulsion nacelles in close proximity to a vehicle body at a Mach number of 6

Experimental tests have been conducted to determine possible aerodynamic interference effects due to the lateral positioning of two dimensional propulsion nacelles mounted on a wing surface in close proximity to a vehicle body. The tests were conducted at a Mach number of 6 and a Reynolds number 7 million per foot. The angle of attack range for force tests was -9 deg to 9 deg. The model configurations consisted of combinations of rectangular and trapezoidal cross section bodies with a wing swept 65 and a rectangular planform wing. A pair of two dimensional, flow through propulsion nacelles simulated full capture inlet operation.

Vahl, W. A.↗
NASA NTRS1959

External Interference Effects of Flow Through Static-Pressure Orifices of an Airspeed Head at Several Supersonic Mach Numbers and Angles of Attack

Wind-tunnel tests have been made to determine the static-pressure error resulting from external interference effects of flow through the static-pressure orifices of an NACA airspeed head at Mach numbers of 2.4, 3.0, and 4.0 for angles of attack of 0 deg, 5 deg, 10 deg, and 15 deg. Within the accuracy of the measurements and for the range of mass flow covered, the static-pressure error increased linearly with increasing mass-flow rate for both the forward and rear sets of orifices at all Mach numbers and angles of attack of the investigation. For a given value of flow coefficient, the static-pressure error varied appreciably with Mach number but only slightly with angle of attack. For example, for a flow coefficient out of the orifices of 0.01 (the approximate value for a vertically climbing airplane for which the airspeed system incorporates an airspeed meter, a Mach meter, and an altimeter), the error increased from about 5 percent to about 12 percent of the static pressure as the Mach number increased from 2.4 to 4.0 with the airspeed head at an angle of attack of 0 deg.

Silsby, Norman S.↗
NASA NTRS1985

Prediction of HiMAT RPRV component interference effects at transonic speeds

Detailed surface flow field analyses of the NASA Highly Maneuverable Aircraft Technology Remotely Piloted Research Vehicle (HiMAT RPRV) are described. Computational predictions are provided by a nonlinear finite difference transonic wing-body code. Component interference effects are obtained through modifications in lifting surface twist and camber boundary conditions. Complex aircraft interactions created by wing-tip fins, landing gear, and lower surface wing actuator fairings are included. Lifting surface viscous flow effects are modeled using a two-dimensional 'strip' boundary layer method. Correlations with flight test data presented demonstrate the high degree of accuracy achieved for this realistic aircraft configuration. This methodology and approach appears to be generally applicable to other multisurface configurations.

Laiosa, J.↗
NASA NTRS1972

Microwave emission from geological materials - Observations of interference effects.

Microwave radiometric field observations were conducted at wavelengths of 21, 2.8, and 0.95 cm to determine the microwave penetration depth of a number of sands and gravels as a function of particle size and moisture content. Observations of a reflecting plate covered with varying thicknesses of test material exhibit a pronounced oscillatory behavior that is consistent with established electromagnetic theory for plane-parallel layered mediums. Utilization of this interference effect is proposed as a microwave radiometric technique for determining the bulk electrical properties of geologic materials, snow, ice, and other materials readily adapted to layering experiments.

Blinn, J. C., III↗
NASA NTRSDate not supplied

CDISC Remote Design Method to Simulate Aircraft Interference Effects for the CATNLF Flight Test

The Crossflow Attenuated Natural Laminar Flow (CATNLF)flight test is an experimental evaluation of a laminar flow design approach that will be conducted on a small transonic wing-like model suspended from the Centerline Instrumented Pylon (CLIP) underneath an F-15 vehicle. The upcoming flight testis anticipated to provide experimental data that may be useful for transition prediction code calibrations or laminar flow computational studies. For the computational results to be reliable, relevant aerodynamics must be included in the simulations. It has been shown that the F-15 vehicle produces a notable aerodynamic influence on the CATNLF test article, and that removing the F-15 vehicle from the simulation significantly alters the laminar flow behavior. Because the F-15 vehicle is not a publicly-releasable geometry, if the CATNLF flight test dataset is to be widely used by the community, an alternative method to ensure that the CATNLF test article flight configuration aerodynamics is properly modeled is required. The objective of this research is to use the CDISC aerodynamic design tool to perform a remote design of a surface that would replicate the aerodynamic influence on the CATNLF test article. This new design approach, referred to as the Equivalent Loading via Interference Surface Effects (ELISE), is presented in this paper, including the details on the design setup and results. The ELISE design successfully reproduced theF-15 influence on the CATNLF test article, with predicted transition location within an average of 4% chord of the full flight configuration. An off-design assessment is included for small perturbations in Mach and sideslip angle that suggest the ELISE design can cover a reasonable range of expected flight conditions with the same geometry. This paper is intended to explain the design approach, as well as show results that can be expected when utilizing the ELISE design method.

CDISC↗
NASA NTRSDate not supplied

CDISC Remote Design Method to Simulate Aircraft Interference Effects for the CATNLF Flight Test

The Crossflow Attenuated Natural Laminar Flow (CATNLF) flight test is an experimental evaluation of a laminar flow design approach that will be conducted on a small transonic wing-like model suspended from the Centerline Instrumented Pylon (CLIP) underneath an F-15 vehicle. The upcoming flight test is anticipated to provide experimental data that may be useful for transition prediction code calibrations or laminar flow computational studies. For the computational results to be reliable, relevant aerodynamics must be included in the simulations. It has been shown that the F-15 vehicle produces a notable aerodynamic influence on the CATNLF test article, and that removing the F-15 vehicle from the simulation significantly alters the laminar flow behavior. Because the F-15 vehicle is not a publicly-releasable geometry, if the CATNLF flight test dataset is to be widely used by the community, an alternative method to ensure that the CATNLF test article flight configuration aerodynamics is properly modeled is required. The objective of this research is to use the CDISC aerodynamic design tool to perform a remote design of a surface that would replicate the aerodynamic influence on the CATNLF test article. This new design approach, referred to as the Equivalent Loading via Interference Surface Effects (ELISE), is presented in this paper, including the details on the design setup and results. The ELISE design successfully reproduced the F-15 influence on the CATNLF test article, with predicted transition location within an average of 4% chord of the full flight configuration. An off-design assessment is included for small perturbations in Mach and sideslip angle that suggest the ELISE design can cover a reasonable range of expected flight conditions with the same geometry. This paper is intended to explain the design approach, as well as show results that can be expected when utilizing the ELISE design method.

CDISC↗
NASA NTRS2004

Software Reduces Radio-Interference Effects in Radar Data

A computer program suppresses the effects of narrow-band radio-frequency interference (RFI) on the data collected by a wide-band radar system. The need for this program arises because some advanced wide-band synthetic-aperture radar systems utilize frequency bands that include frequencies used by other radio services. In this program, the RFI environment is represented by an auto-regressive process, the frequency band of which is narrow relative to that of the radar. Most of the RFI signals, both narrow- and wide-band, are estimated in one pass of a least-mean-square (LMS) adaptive filter. The program implements three popular LMS algorithms: the time-domain LMS, the frequency-domain LMS, and the filter-bank LMS adaptive-filter algorithms. The program can be run in a manual or automatic mode. In the manual mode, the user selects the filter parameters prior to execution. In the automatic mode, the program utilizes median-filter and spectral-estimation techniques plus the variable-step-size LMS algorithm for automatic determination of filter parameters, and the parameters are adaptively changed as functions of the inputs, resulting in better overall performance.

Le, Charles T-C↗
NASA NTRS1977

Aerodynamic interference effects on tilting proprotor aircraft

The Green's function method was used to study tilting proprotor aircraft aerodynamics with particular application to the problem of the mutual interference of the wing-fuselage-tail-rotor wake configuration. While the formulation is valid for fully unsteady rotor aerodynamics, attention was directed to steady state aerodynamics, which was achieved by replacing the rotor with the actuator disk approximation. The use of an actuator disk analysis introduced a mathematical singularity into the formulation; this problem was studied and resolved. The pressure distribution, lift, and pitching moment were obtained for an XV-15 wing-fuselage-tail rotor configuration at various flight conditions. For the flight configurations explored, the effects of the rotor wake interference on the XV-15 tilt rotor aircraft yielded a reduction in the total lift and an increase in the nose-down pitching moment. This method provides an analytical capability that is simple to apply and can be used to investigate fuselage-tail rotor wake interference as well as to explore other rotor design problem areas.

Soohoo, P.↗