Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ion impact angle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Thermal evaporation of thin Li films

Thermal evaporation of lithium is considered a promising technique for the fabrication of clean lithium thin films for solid-state batteries. Here, in this study, we present a practical investigation of nanometer scale lithium films prepared by evaporation on different substrates. These substrates include Li-alloying and nonalloying metals as well as different classes of solid-state lithium-ion conductors. The deposition rate was also varied. For films less than 100 nm thick, the data show that the deposition rate has the biggest impact on the surface coverage. At 50 Å/s, Li forms small particles <1 μm in diameter while higher deposition rate of 150 Å/s resulted in more uniform film morphology on all the substrates. At the lower deposition rates, the wetting of Li to the substrate will impact the particle morphology. We also used the particles to estimate a contact angle between Li and the substrate to qualitatively compare the adhesion from substrate to substrate. The smallest contact angle was observed from lithium films on Li 7 La 3 Zr 2 O 12 and LiPON (nominal Li 2.94 PO 3.5 N 0.31 ) solid-state electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Validation of a synthetic fast ion loss detector model for Wendelstein 7-X

Abstract We present the first validated synthetic diagnostic for fast ion loss detectors (FILDs) in the Wendelstein 7-X (W7-X) stellarator. This model has been developed on, and validated against experimental data from, a FILD provided by the National Institute for Fusion Science (NIFS-FILD), with potential future applicability to the existing Faraday Cup FILD (FC-FILD) on W7-X as well as the scintillating FILD (S-FILD) currently under development. A workflow combining Monte Carlo codes BEAMS3D and ASCOT5 is used to track fast ions produced by neutral beam injection from the moment of ionization until they are thermalized or lost from the last closed flux surface, and from there to a virtual plane which serves as a projection of the entrance aperture to the FILD. Simulations in ASCOT5 are analyzed via a geometric method to determine the probability of transmission through the FILD aperture and onto the detector as a function of normalized momentum, pitch angle, gyrophase, and position at the virtual plane. This probability is then applied to the simulated ions arriving from the plasma, producing a simulated signal from a computationally tractable number of simulated fast ions. Simulated signals are presented for two W7-X experiments with neutral beam injection and quantitatively compared with experimental measurements from the NIFS-FILD diagnostic. An estimate of the frequency of charge-exchange with neutral particles in the edge is performed, and it is found that this process may have a significant impact on the measured signals.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Minimizing Selection Bias in Inclusive Jets in Heavy-Ion Collisions with Energy Correlators

The first-ever measurement of energy correlators within inclusive jets produced in heavy-ion collisions, revealed by the CMS Collaboration, shows a clear enhancement at large angles relative to the proton-proton (p-p) baseline. However, interpreting this enhancement is complicated due to selection bias from energy loss, which also distorts the energy correlator heavy-ion to p-p ratio in the hadronization region, hindering our understanding of parton/hadron dynamics in a colored medium. In this Letter, we introduce a new ratio of energy correlator observables that removes the leading effects of selection bias from the two-point energy correlator spectrum (E2C). PYTHIA and HERWIG simulations show that the impact of selection bias in the E2C is reduced by an order of magnitude, while sensitivity to any other medium modifications is retained. This quantity can be obtained directly from the experimental measurements presented by CMS, as illustrated in an accompanying note [C. Andres and J. Holguin, arXiv:2409.07526].

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Interpretive modeling of tungsten divertor leakage during experiments with neon gas seeding

Abstract Many existing and future tokamaks with tungsten divertors operate, or will operate, with low- Z impurity seeding, but the direct effect of these seeded impurities on tungsten Scrape-off-Layer (SOL) transport has not been explored in detail. This paper reports on a DIII-D experiment designed to test how tungsten divertor leakage from the Small-Angle Slot V-Shaped, tungsten-coated divertor is impacted by neon seeding at a variety of injection rates and poloidal injection locations. Measurements from the experiment show an inverse relationship between the neon injection rate and the tungsten core penetration factor. Interpretive modeling is performed with a combination of the SOLPS-ITER and DIVIMP codes to assess the underlying tungsten behavior. The modeling results show that the reduction in tungsten divertor leakage is driven by both an increase in the divertor collisionality as well as a reduction in the ion temperature gradient near the divertor target. Collisions between low- Z impurities and tungsten impurities are found to have a significant impact on the tungsten SOL transport, such that ignoring the low- Z impurity collisional effects on the tungsten transport can result in an overestimate of the divertor leakage by an order-of-magnitude. Given the importance of these localized interactions, neon seeding from the closed, slot-like divertor has a clear advantage in being able to reduce tungsten divertor leakage without the high levels of neon core contamination that occur when seeding from other poloidal locations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Impact of Cation Insertion on Semiconducting Polymer Thin Films toward Electrochemical Energy Conversion

Semiconducting polymers are being explored for electrochemical and photoelectrochemical energy transformation and storage applications. For these applications, it is critical to understand how ion insertion from the electrolyte into polymer electrodes modulates the polymer electronic structure and electron doping levels. Here, this study explores electrochemical cation insertion in the n-type conjugated redox polymer P90, composed of alternating naphthalene diimide (NDI) acceptor and bithiophene (T2) donor units, where the NDI units are functionalized with heptaethylene glycol (HEG, 90%) and 2-octyl dodecyl (OD, 10%) side chains. By combining in situ techniques (UV-vis absorption and Raman spectroscopies with electrochemistry), structural analysis using ex situ grazing-incidence wide-angle X-ray scattering (GIWAXS), and density functional theory (DFT) calculations, we reveal that dications enable negative polaron and bipolaron formation in the P90 at less reducing potentials while supporting more bipolaron formation than the monocations; moreover, larger dications with smaller hydrated radii increase the maximum P90 electron doping level. We also determine that the monocations lead to more thermodynamically stabilized polarons compared with the dications. These findings highlight the critical role of cation identity in tuning electrochemical charging, charge stabilization, and electronic structure of n-type conjugated redox polymers, providing guidance on the rational design of polymer-based (photo)electrochemical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Fast ion confinement in quasi-axisymmetric stellarator equilibria

This report presents an initial analysis of the fast ion confinement and losses within quasi-axisymmetric stellarator equilibria in consideration by Thea Energy. The equilibria have not yet been explicitly optimized for fast particle confinement and require validation. Modeling with the ASCOT5 code is used to directly examine the fast ion transport. The particle tracking simulations are purely (neo)classical in nature and simply contain the supplied equilibrium and collisions (pitch-angle, energy slowing, and velocity diffusion) from supplied thermal profiles. Uniform marker deposition is used to probe the general confinement properties of the equilibria while a realistic beam-born population is provided from the BEAMS3D code and an alpha particle population is calculated from a fusion source integrator. A first wall is included and defines the loss boundary. Analysis for NBI ions within Thea Energy’s conceptual Eos neutron source are presented along with alpha particles in an enlarged DT-plasma. The fast ions are assessed in regards to their confinement time, pitch, energy, and spatial coordinates. For each population, the impact of collisions and orbit drifts are discussed. It is found that NBI born ions in Eos are strongly confined until slowing-down, owing largely to the tangential injection geometry, while 22% of DT-born alpha energy is lost in the scaled device, indicating that any fusion pilot plant design optimization should include metrics for fast ion confinement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Self-Assembly of Partially Charged Diblock Copolymer-Homopolymer Ternary Blends

Ternary blends comprising of a diblock copolymer and the corresponding homopolymers provide ready access to a variety of morphologies, but the impact of charge on their phase behavior has not been studied extensively. Here, three partially charged ternary blends consisting of symmetric poly[(oligo(ethylene glycol) methyl ether methacrylate-co-oligo(ethylene glycol) propyl sodium sulfonate methacrylate)] (POEGMA#), polystyrene (PS), and POEGMA#-PS with different charge fractions were prepared, where # denotes the mole fraction of charged monomers in the POEGMA chain. Here, the phase behavior was systematically studied using small-angle X-ray scattering (SAXS), and isothermal phase diagrams at 120 °C were constructed. The resulting isothermal planes contain a wide lamellar (LAM) phase window with a slight deviation from symmetry for ion-containing ternary blends, due to the homopolymer size difference. Given the absence of any significant change in the phase diagrams as the charge fraction increases, the role of charge is primarily to increase the segregation strength in the ternary system, as in the case of partially charged diblock polymers. In addition, examination of the increase in domain size along the volumetrically symmetric isopleth reveals a “dry-brush” like swelling behavior of homopolymers in all three blends, presumably due to the space-filling nature of the oligomeric ethylene glycol side chains on POEGMA.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Advanced characterization of surface-modified nanoparticles and nanofilled antibacterial dental adhesive resins

Nanotechnology can improve the performance of dental polymers. The objective of this study was to modify the surfaces of nanoparticles with silanes and proteins, characterize nanoparticles’ agglomeration levels and interfaces between nanoparticles and the polymeric matrix. Undoped (n-TiO 2 ), nitrogen-doped (N_TiO 2 ) and nitrogen-fluorine co-doped titanium dioxide nanoparticles (NF_TiO 2 ) were synthesized and subjected to surface modification procedures in preparation for Small-Angle X-Ray Scattering (SAXS) and Small-Angle Neutron Scattering (SANS) characterizations. Experimental adhesives were manually synthesized by incorporating 20% (v/v) of n-TiO 2 , N_TiO 2 or NF_TiO 2 (as-synthesized or surface-modified) into OptiBond Solo Plus (OPTB). Specimens (n = 15/group; d = 6.0 mm, t = 0.5 mm) of OPTB and experimental adhesives were characterized using Time-of-Flight Secondary Ion Mass Spectroscopy (ToF-SIMS), 2-D ToF-SIMS chemical imaging and SANS. SAXS results indicated that surface-modified nanoparticles displayed higher scattering intensities in a particle-size dependent manner. ToF-SIMS results demonstrated that nanoparticles’ incorporation did not adversely impact the parental polymer. 2-D ToF-SIMS chemical imaging demonstrated the distribution of Ti + and confirmed nitrogen-doping levels. SANS results confirmed nanoparticles’ functionalization and revealed the interfaces between nanoparticles and the polymer matrix. Metaloxide nanoparticles were successfully fabricated, incorporated and covalently functionalized in a commercial dental adhesive resin, thereby supporting the utilization of nanotechnology in dentistry.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Full 3D Kinetic Modeling and Quantification of Positive Streamer Evolution in an Azimuthally Swept Pin-to-Plane Wedge Geometry

Cathode-directed streamer evolution in near atmospheric air is modeled in 3D pin-to-plane geometries using a 3D kinetic Particle-In-Cell (PIC) code that simulates particle-particle collisions via the Direct Simulation Monte Carlo (DSMC) method. Due to the computational challenges associated with a complete 360° volumetric domain, a practical alternative was achieved using a wedge domain and a range of azimuthal angles was explored (5°, 15°, 30°, and 45°) to study possible effects on the streamer growth and propagation due to the finite wedge angle. A DC voltage of 6 kV is administered to a hemispherical anode of radius 100 μm, with a planar cathode held at ground potential, generating an over-volted state with an electric field of 4 MV/m across a 1500 μm gap. The domain is seeded with an initial ion and electron density of 10 18 m -3 at 1 eV temperature confined to a spherical region of radius 100 μm centered at the tip of the anode. The air chemistry model [1] includes standard Townsend breakdown mechanisms (electron-neutral elastic, excitation, ionization, attachment, and detachment collision chemistry and secondary electron emission) as well as streamer mechanisms (photoionization and ion-neutral collisions) via tracking excited state neutrals which can then either quench via collisions or spontaneously emit a photon based on specific Einstein-A coefficients [2, 3]. In this work, positive streamer dynamics are formally quantified for each wedge angle in terms of electron velocity and density as temporal functions of coordinates r, Φ, and z. Applying a random plasma seed for each simulation, particles of interest are tracked with near femtosecond temporal resolution out to 1.4 ns and spatially binned. This process is repeated six times and results are averaged. Prior 2D studies have shown that the reduced electric field, E/n, can significantly impact streamer evolution [4]. We extend the analysis to 3D wedge geometries, to limit computational costs, and examine the wedge angle’s effect on streamer branching, propagation, and velocity. Results indicate that the smallest wedge angle that produced an acceptably converged solution is 30°. The potential effects that a mesh, when under-resolved with respect to the Debye length, can impart on streamer dynamics and numerical heating were not investigated, and we explicitly state here that the smallest cell size was approximately 10 times the minimum λ D in the streamer channel at late times. This constraint on cell size was the result of computational limitations on total mesh count.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Mitigating Sodium Ordering for Enhanced Solid Solution Behavior in Layered NaNiO 2 Cathodes

Abstract The O‐type layered nickel oxides suffer from undesired cooperative Jahn–Teller distortion stemming from Ni 3+ ions and undergo multiple biphasic structural transformations during the insertion/extraction of large Na + ions, posing a significant challenge to stabilize the structural integrity. We present here a systematic investigation of the impact of substituting 5 % divalent (Mg 2+ ) or trivalent (Al 3+ or Co 3+ ) ions for Ni 3+ to alleviate Na + ion ordering and perturb the Jahn–Teller effect to enhance structural stability. We gauge a fundamental understanding of the Mg−O and Na−O or Mg−O−Na bonding interactions, noting that the ionicity of the Mg−O bond deshields the electronic cloud of oxygen from Na + ions. Furthermore, calculations of the Van Vleck distortion modes reveal a relaxation of NiO 6 octahedra from Jahn–Teller distortion and a reduced electron density at the interlayer with Mg 2+ substitution. Long‐range ( operando X‐ray diffraction) and short‐range (magic angle spinning nuclear magnetic resonance) structural analyses provide insights into reduced ordering, allowing a stable continuous solid solution. Overall, Mg‐substitution results in a high‐capacity retention of ~96 % even after 100 cycles, showcasing the potential of this strategy for overcoming the structural instabilities and enhancing the performance of sodium‐ion batteries.

Sada, Krishnakanth↗
DOE OSTI2020

Tin-based ionic chaperone phases to improve low temperature molten sodium–NaSICON interfaces

High temperature operation of molten sodium batteries impacts cost, reliability, and lifetime, and has limited the widespread adoption of these grid-scale energy storage technologies. Poor charge transfer and high interfacial resistance between molten sodium and solid-state electrolytes, however, prevents the operation of molten sodium batteries at low temperatures. In this study, in situ formation of tin-based chaperone phases on solid state NaSICON ion conductor surfaces is shown in this work to greatly improve charge transfer and lower interfacial resistance in sodium symmetric cells operated at 110 °C at current densities up to an aggressive 50 mA cm –2 . It is shown that static wetting testing, as measured by the contact angle of molten sodium on NaSICON, does not accurately predict battery performance due to the dynamic formation of a chaperone NaSn phase during cycling. This work demonstrates the promise of sodium intermetallic-forming coatings for the advancement of low temperature molten sodium batteries by improved mating of sodium–NaSICON surfaces and reduced interfacial resistance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Hard-photon-triggered jets in 𝑝−𝑝 and 𝐴−𝐴 collisions

An investigation of high-transverse-momentum (high-𝑝 𝑇 ) photon-triggered jets in proton-proton (𝑝−𝑝) and ion-ion (𝐴−𝐴) collisions at $\sqrt{s_{NN}}$=0.2 and 5.02TeV is carried out, using the multistage description of in-medium jet evolution. Monte Carlo simulations of hard scattering and energy loss in heavy-ion collisions are performed using parameters tuned in a previous study of the nuclear modification factor (𝑅 𝐴⁢𝐴 ) for inclusive jets and high-𝑝𝑇 hadrons. We obtain a good reproduction of the experimental data for photon-triggered jet 𝑅 𝐴⁢𝐴 , as measured by the ATLAS detector, the distribution of the ratio of jet to photon 𝑝 𝑇 (𝑋 𝐽⁢𝛾 ), measured by both CMS and ATLAS, and the photon-jet azimuthal correlation as measured by CMS. We obtain a moderate description of the photon-triggered jet 𝐼 𝐴⁢𝐴 , as measured by STAR. A noticeable improvement in the comparison is observed when one goes beyond prompt photons and includes bremsstrahlung and decay photons, revealing their significance in certain kinematic regions, particularly at 𝑋 𝐽⁢𝛾 >1. Moreover, azimuthal angle correlations demonstrate a notable impact of bremsstrahlung photons on the distribution, emphasizing their role in accurately describing experimental results. This work highlights the success of the multistage model of jet modification to straightforwardly predict (this set of) photon-triggered jet observables. This comparison, along with the role played by bremsstrahlung photons, has important consequences on the inclusion of such observables in a future Bayesian analysis.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Transition Metal Dichalcogenide MoS 2 : Oxygen and Fluorine Functionalization for Selective Plasma Processing

Low-temperature plasma processing is a promising technique for tailoring transition metal dichalcogenides (TMDs). For chalcogen substitution processing, a key challenge is to identify the ion energy window that enables selective chalcogen removal while preserving the metal lattice. Using ab initio molecular dynamics (AIMD), we demonstrate that oxygen and fluorine functionalization widen the processing window by significantly lowering the sulfur sputtering energy threshold (E sputt,S ) of MoS 2 from ∼30 to ∼10 eV via formation of sputtering products such as SO 2 and SF n . Additionally, we show that experimentally relevant cryogenic temperatures strongly affect E sputt,S (T). The dependence is confirmed via AIMD and also predicted by a mechanistic parameter-free theory, suggesting that E sputt (T) generalizes to other TMDs, functionalizations, and surface impact conditions. Our results highlight oxygen/fluorine functionalization, ionic impact angle, and material temperature to be key control parameters for selective, damage-controlled chalcogen removal in TMD processing.

Polyachenko, Yury [Princeton Plasma Physics Labora↗
DOE OSTI2024

Mitigating Sodium Ordering for Enhanced Solid Solution Behavior in Layered NaNiO 2 Cathodes

The O-type layered nickel oxides suffer from undesired cooperative Jahn–Teller distortion stemming from Ni 3+ ions and undergo multiple biphasic structural transformations during the insertion/extraction of large Na + ions, posing a significant challenge to stabilize the structural integrity. We present here a systematic investigation of the impact of substituting 5 % divalent (Mg 2+ ) or trivalent (Al 3+ or Co 3+ ) ions for Ni 3+ to alleviate Na + ion ordering and perturb the Jahn–Teller effect to enhance structural stability. Here, we gauge a fundamental understanding of the Mg−O and Na−O or Mg−O−Na bonding interactions, noting that the ionicity of the Mg−O bond deshields the electronic cloud of oxygen from Na + ions. Furthermore, calculations of the Van Vleck distortion modes reveal a relaxation of NiO 6 octahedra from Jahn–Teller distortion and a reduced electron density at the interlayer with Mg 2+ substitution. Long-range (operando X-ray diffraction) and short-range (magic angle spinning nuclear magnetic resonance) structural analyses provide insights into reduced ordering, allowing a stable continuous solid solution. Overall, Mg-substitution results in a high-capacity retention of ~96 % even after 100 cycles, showcasing the potential of this strategy for overcoming the structural instabilities and enhancing the performance of sodium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Anion exchange membranes based on (3-acrylamidopropyl) trimethylammonium chloride (APTA) and phenyl Acrylate: Impact of crosslinker and crosslinker content on physiochemical properties and transport behavior of acetate and formate

CO 2 reduction cells are innovative devices that convert CO 2 into valuable chemicals, such as formate (OFm - ) and acetate (OAc - ), at the cathode. One of the key challenges in these devices is the development of ion exchange membranes that enable the transport of charge carriers between electrodes while minimizing the transfer of CO 2 reduction products. This study focuses on the preparation and characterization of crosslinked anion exchange membranes (AEMs) made of phenyl acrylate (PA) and (3-acrylamidopropyl) trimethylammonium chloride (APTA), crosslinked with either poly(ethylene glycol) diacrylate (PEGDA) or N,N’-methylenebisacrylamide (MBAA). Here, the membranes are characterized to understand their physiochemical properties and corresponding transport behavior through characterization of water volume fraction, mechanical properties, ionic conductivity, ion exchange capacity, water contact angle, glass transition temperature as well as their permeability and solubility to formate and acetate. MBAA crosslinked membranes exhibit higher Young’s modulus and lower strain at break compared to PEGDA-crosslinked membranes, which is attributed to their shorter chain length. Within a series of membranes of varied comonomer content, for either PEGDA or MBAA as crosslinker, permeabilities generally follow free volume theory (increasing permeability with increasing water content where water content increases with decreasing crosslinker content). Interestingly, for membranes with different crosslinkers but analogous water volume fraction significant differences (∼2 orders of magnitude) in permeability are observed which we attribute to differences in chain mobility as characterized through the glass transition temperature.

25 ENERGY STORAGE↗
DOE OSTI2020

Impact of Dispersion Solvent on Ionomer Thin Films and Membranes

Perfluorosulfonic acid (PFSA) ionomers are an important class of materials that many electrochemical devices rely on as their ion-conducting electrolyte. Often, PFSA films are prepared through solution-processing techniques. Previous research has demonstrated that the solvent environment affects PFSA dispersion conformation, but it is not clear to what extent (if at all) these conformational effects persist for thin films and membranes upon casting, nor how dispersion solvent impacts film formation during the drying process. Here in this paper, we explore these questions by systematically examining the effect of Thin Film all length scales affected by dispersion solvent water and n-propanol mixtures on PFSA thin-film formation and structure, membrane structure, and resulting properties. Using a combination of in situ, time-resolved grazing incidence X-ray scattering and tender wide-angle X-ray scattering, it is shown that films prepared from high-water-concentration dispersions exhibit stronger interactions and arrangement upon drying, and possess larger network domain sizes than those prepared from low-water-concentration dispersions. These stronger interactions likely manifest in greater network connectivity, as evidenced by enhanced conductivity for membranes and decreased water uptake for thin films. Significantly, these solvent-induced differences persist even after thermal annealing. It is clear that the dispersion solvent choice is a critical parameter controlling PFSA nano- and mesoscale structure and presents an important dial with which to direct PFSA macroscale properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Ferromagnetic MnBi 4 Te 7 obtained with low-concentration Sb doping: A promising platform for exploring topological quantum states

The tuning of the magnetic phase, chemical potential, and structure is crucial to observe diverse exotic topological quantum states in Mn Bi 2 Te 4 (Bi 2 Te 3 ) m (m = 0–3). Here we show a ferromagnetic (FM) phase with a chiral crystal structure in Mn (Bi 1–x Sb x ) 4 Te 7 , obtained via tuning the growth conditions and Sb concentration. Unlike previously reported Mn (Bi 1–x Sb x ) 4 Te 7 , which exhibits FM transitions only at high Sb doping levels, our samples show FM transitions (T C = 13.5 K) at 15%–27% doping levels. Furthermore, our single-crystal x-ray-diffraction structure refinements find Sb doping leads to a chiral structure with the space group of P3, contrasted with the centrosymmetric $P\bar{3}m1$ crystal structure of the parent compound MnBi 4 Te 7 . Through angle-resolved photoemission spectroscopy measurements, we also demonstrated that the nontrivial band topology is preserved in the Sb-doped FM samples. Given that the nontrivial band topology of this system remains robust for low Sb doping levels, our success in making FM Mn(Bi 1–x Sb x ) 4 Te 7 with x = 0.15, 0.175, 0.2, and 0.27 paves the way for realizing the predicted topological quantum states, such as the axion insulator and Weyl semimetals. Additionally, we also observed magnetic glassy behavior in both antiferromagnetic MnBi 4 Te 7 and FM Mn (Bi 1–x Sb x )4 Te 7 samples, which we believe originates from cluster spin-glass phases coexisting with long-range antiferromagnetic/FM orders. Further, we have also discussed how the antisite Mn ions impact the interlayer magnetic coupling and how FM interlayer coupling is stabilized in this system.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tungsten erosion during L-mode discharges in the DIII-D SAS-VW divertor

A series of L-mode plasma discharges was performed in the DIII-D tokamak to assess the impact of outer strike point (OSP) position and toroidal magnetic field direction on erosion and core contamination potential of the recently-installed, tungsten-coated Small Angle Slot (SAS-VW) divertor. In one discharge, in-slot emission spectroscopy measured an<48 % increase in the W gross erosion rate when the OSP was moved 3 cm outwards, away from the V-shaped vertex of the slot divertor. However, the effective W yield (erosion rate divided by the incident D flux) was, overall, insensitive to changes in OSP location. Consistently low estimates of the effective W yield based on measurements taken a few cm outwards from the vertex suggest potentially significant C surface contamination. No W emission signal was detected when orienting the toroidal magnetic field such that the ion B×∇B drift direction is pointed away from the X-point. However, measurements of W content in the plasma core for both toroidal magnetic field directions suggest the presence of additional, unmeasured sources of erosion. The difference in the measured core W density with OSP position is much greater than the difference in the measured erosion rates, which may suggest that the leakage of eroded impurities out of the divertor is governed primarily through the parallel ion temperature gradient and friction forces.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗