A calculation of proton-induced damage in germanium
High energy proton irradiation damage in germanium semiconductor
PROTON IRRADIATION↗
SEARCH · Search NASA
Results for “Irradiation Damage”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Technological aspects in blanket design: Effects of micro-alloying and thermo-mechanical treatments of EUROFER97 type steels after neutron irradiation
Presently available data on neutron irradiation damage raise doubts on the feasibility of using EUROFER97 steel for a water-cooled starter blanket in a DEMO reactor, since the ductile-to-brittle transition temperature (DBTT) increases significantly for irradiation temperatures below 350°C. The additional DBTT shift caused by H and He transmutation can only be estimated based on very few results with isotopically tailored EUROFER97 steel. Conservative calculations show that the DBTT of EUROFER97 steel could exceed the operating temperature in water-cooled starter blankets within a relatively short time period. This paper presents results from a EUROfusion funded irradiation campaign that was performed in the High Flux Isotope Reactor at Oak Ridge National Laboratory. The paper compares ten newly developed reduced activation ferritic-martensitic (RAFM) steels irradiated to a nominal dose of 2.5 dpa at 300°C. The post-irradiation experiments using Small Specimen Test Technology included hardness, tensile, and fracture mechanics tests combined with fractography and microstructure analysis are presented. Results show that micro-alloying EUROFER97-type steels influenced the mechanical properties but a dominating impact on irradiation damage resistance could not be identified. In contrast, specific thermo-mechanical treatments lead to better DBTT behavior. Discussion about irradiation response to heat treatment conditions is also given. Here, despite requiring data also at high dpa values, the results indicate that with these modified materials an increased lifetime and potentially also an increased operating temperature window can be achieved compared to EUROFER97.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Correlation of electron and proton irradiation-induced damage in InP solar cells
When determining the best solar cell technology for a particular space flight mission, accurate prediction of solar cell performance in a space radiation environment is essential. The current methodology used to make such predictions requires extensive experimental data measured under both electron and proton irradiation. Due to the rising cost of accelerators and irradiation facilities, such extensive data sets are expensive to obtain. Moreover, with the rapid development of novel cell designs, the necessary data are often not available. Therefore, a method for predicting cell degradation based on limited data is needed. Such a method has been developed at the Naval Research Laboratory based on damage correlation using 'displacement damage dose' which is the product of the non-ionizing energy loss (NIEL) and the particle fluence. Displacement damage dose is a direct analog of the ionization dose used to correlate the effects of ionizing radiations. In this method, the performance of a solar cell in a complex radiation environment can be predicted from data on a single proton energy and two electron energies, or one proton energy, one electron energy, and Co(exp 60) gammas. This method has been used to accurately predict the extensive data set measured by Anspaugh on GaAs/Ge solar cells under a wide range of electron and proton energies. In this paper, the method is applied to InP solar cells using data measured under 1 MeV electron and 3 MeV proton irradiations, and the calculations are shown to agree well with the measured data. In addition to providing accurate damage predictions, this method also provides a basis for quantitative comparisons of the performance of different cell technologies. The performance of the present InP cells is compared to that published for GaAs/Ge cells. The results show InP to be inherently more resistant to displacement energy deposition than GaAs/Ge.
Walters, Robert J.↗
Mechanical Behavior of Neutron Irradiated Refractory Multi-Principal Element Alloys Processed via Spark Plasma Sintering
The search for advanced materials capable of withstanding the extreme conditions of Generation IV reactors is a critical area in materials science research. These reactors operate under severe environments, including high temperatures, corrosion, stress, and irradiation damage. Consequently, there is a need for innovative alloy systems to ensure the reliability and longevity of proposed Generation IV reactor components. Refractory multi-principal-element alloys (RMPEA) have emerged as a promising candidate due to their exceptional properties. These alloys, characterized by their composition of multiple principal elements in near-equiatomic ratios, exhibit superior resistance to irradiation damage, reduced void swelling, enhanced microstructural stability, and minimal irradiation-induced hardening. While initial studies on RMPEAs have shown promising results, most research has been limited to thin films, nanocrystalline microstructures, and ion irradiation, which do not accurately represent the behavior of bulk materials. To address this gap, our research focused on the neutron irradiation of bulk RMPEAs. We aim to conduct comprehensive post-irradiation examinations (PIE) of RMPEAs irradiated at the Advanced Test Reactor at Idaho National Laboratory. The RMPEAs were synthesized using spark plasma sintering (SPS) with mechanically alloyed metallurgical powder. The RMPEA specimens are a MoNbTi alloy system with additions of -Zr, and -ZrV. Furthermore, PIE consisted of mechanical testing and advanced materials characterization. The mechanical testing consisted of sub-sized tensile testing, micro- and nano- indentation. Microstructural characterization included scanning electron microscopy and transmission electron microscopy. Mechanical testing coupled with advanced microscopy techniques provides insight into phase morphology and its effects on the mechanical properties of the RMPEA specimens. The results indicate that both pristine and irradiated RMPEA specimens exhibited brittle behavior during tensile testing, which can be attributed to their heterogeneous microstructure. The SPS manufacturing process did not include any post treatment, which resulted in a heterogeneous microstructure. Energy-dispersive X-ray spectroscopy revealed the presence of intermetallic such as laves phases within the microstructure. Specifically, Ti-rich precipitates were observed in the MoNbTi specimen, while Mo-rich precipitates were found in the MoNbTiZrV specimen. Nano-hardness testing of pristine samples showed that the laves phases exhibited higher hardness values compared to the matrix phase, suggesting that precipitate hardening is likely the dominant hardening mechanism in these specimens. The results from this work will be used to build a finite element model to predict mechanical behavior of future MPEA compositions. Thus, enabling for a streamlined approach to developing novel MPEAs for the nuclear industry.
36 - MATERIALS SCIENCE↗
Annealing kinetics of electron-irradiated GaAs heteroface solar cells in the range 175-200 C
Annealing of electron-irradiation damage in GaAs solar cells is important for space applications. This paper describes studies conducted to understand this annealing process. GaAs heteroface solar cells were irradiated with 10 to the 15th 1-MeV electrons/sq cm followed by thermal annealing. An activation energy for annealing of 1.25 + or - 0.14 eV and a frequency factor of (3.7 + or - 1.9) x 10 to the 9th per sec were determined. A small component of the irradiation damage which does not anneal measurably at 200 C was observed.
Walker, G. H.↗
Comparison of Ion and Neutron Irradiations to 3 dpa at 500C in Ferritic-Martensitic Alloys
The growing global demand for energy will increasingly call upon advanced nuclear fission reactors to supply safe and reliable electricity. The structural and fuel cladding components of these reactors will be subject to extreme conditions of irradiation damage up to several hundred displacements per atom (dpa) at temperatures as high as 700°C. Ferritic-martensitic (F-M) steels are leading candidates for these challenging conditions due to their strength and dimensional stability under irradiation. In order to accelerate the process for evaluating F-M alloys, charged particles are increasingly being used to emulate neutron irradiations. Charged particle irradiations allow the possibility of conducting irradiation experiments within a shorter time period (i.e. at a rate up to 4 orders of magnitude faster) and with minimal radioactivation of the material, enabling lower cost and faster turnaround of post irradiation examination and analysis. However, the irradiation dose rate, damage cascade morphologies, and irradiation damage depth profiles all differ widely between protons, heavier ions, and neutrons. Currently, there is limited understanding of the significance of these physical differences and how they manifest in the irradiated microstructure and mechanical properties of F-M steels. The objective of this study is to evaluate charged particles as a surrogate for neutron irradiations in F-M alloys by assessing common irradiation conditions using Fe++ ions, protons, and neutrons. Keeping the temperature and dose consistent enables isolation of the effects of each irradiating particle and their respective dose rates and cascade morphologies.
Swenson, M.J.↗
Irradiation-induced damage in concrete-forming aggregates: revisiting literature data through micromechanics
The radiation-induced volumetric expansion (RIVE) of aggregate-forming minerals causes damage in concrete exposed to high levels of fast neutrons fluence ( \(>\,\sim \,10^{19}\, \hbox {n}\,\hbox {cm}^{-2}\) at kinetics energy above 0.1 MeV). Historical post-irradiation RIVE and Young’s modulus data obtained in test reactors were revisited using a polycrystalline homogenization model (self-consistent scheme) accounting for the aggregates’ minerals content and the formation of voids/cracks during irradiation. It was found that the formation of extra voids/cracks can contribute to the aggregate expansion more substantially than the cumulated expansions of aggregate-forming minerals. Furthermore, the rate of void creation appears to be inversely correlated to the silica content, although aggregates of higher silicate contents exhibit higher RIVEs. The loss of Young’s modulus decreases exponentially with the aggregates’ expansion. At a comparable RIVE level, the relative loss of modulus is more significant in aggregates of higher silica content.
36 MATERIALS SCIENCE↗
Microstructurally resolved electrochemical evolution of mechanical- and irradiation-induced damage in nuclear alloys
Abstract There is a need for high-throughput, scale-relevant, and direct electrochemical analysis to understand the corrosion behavior and sensitivity of nuclear materials that are exposed to extreme (high pressure, temperature, and radiation exposure) environments. We demonstrate the multi-scale, multi-modal application of scanning electrochemical cell microscopy (SECCM) to electrochemically profile corrosion alterations in nuclear alloys in a microstructurally resolved manner. Particularly, we identify that both mechanically deformed and irradiated microstructures show reduced charge-transfer resistance that leads to accelerated oxidation. We highlight that the effects of mechanical deformation and irradiation are synergistic, and may in fact, superimpose each other, with implications including general-, galvanic-, and/or irradiation-activated stress-corrosion cracking. Taken together, we highlight the ability of non-destructive, electrochemical interrogations to ascertain how microstructural alterations result in changes in the corrosion tendency of a nuclear alloy: knowledge which has implications to rank, qualify and examine alloys for use in nuclear construction applications.
Chen, Xin↗
The Mechanical Response of High Burnup 17x17 PWR Fuel Rods Under Bending
As a part of the US Department of Energy Office of Nuclear Energy High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory has performed 4pt-bend tests on a series of 17x17 PWR fuel rods that were discharged with rod average burnups between 50 and 60 GWd/MTU. The rods include four different kinds of fuel cladding: standard Zircaloy-4 (Zirc-4), low-tin (LT) Zirc-4, ZIRLO, and M5. Six rods of each type (combining Zirc-4 and LT Zirc-4 as one type) were tested to failure at room temperature and 200 oC. Three of each type experienced a full-length heat treatment cycle from RT to 400 oC to RT with an 8 hr soak at 400 oC to simulate the expected limiting vacuum drying condition, which potentially induces hydride reorientation and causes some annealing of irradiation damage in the cladding. Overall, the fuel rods show significant capacity to deflect in bending and exhibit non-linear deformation before failing. The calculated failure strains range from 1.5% to 3.8%. The simulated vacuum drying heat treatment had the largest effect on fuel rods with ZIRLO and M5 cladding. In both cases the heat treatment caused increases in the plastic strain at failure, suggesting some annealing of irradiation damage is occurring. The finite element modeling of the 4pt bending test assume the pellet is a collection of pellet wedge pieces. The results for the Zircaloy-4 rods suggest that the pellets are bonded to the cladding and friction controls the relative motion of the pellet wedge pieces.
Cantonwine, Paul↗
Mesoscale Modeling of Dislocation Cell Structure Evolution and Radiation-Induced Segregation in Additively Manufactured Austenitic Stainless Steel
Structural alloys under irradiation develop radiation-induced segregation (RIS) at point defect sinks, which lead to undesired changes in the alloy's properties. Additively manufactured austenitic stainless steels are expected to yield a distinct response to irradiation damage owing to their unique as-printed dislocation cell structure. In this talk, we present the development of a mesoscale model for dislocation cell structure evolution coupled with RIS using the MOOSE framework. The evolution of network dislocations within spatially distinct cells and cell walls are modeled using climb-mediated edge annihilation and generation processes. Starting with initial microstructures of as-printed non-equilibrium segregations at dislocation cell walls, our 2D and 3D simulations explore the effects of irradiation temperature, dose rate, dislocation sink bias, and specimen thickness on microstructure evolution. The results will be compared against experimental characterizations of in-situ and ex-situ ion-irradiated samples, and the implications of evolving cell structure on irradiation damage response will be discussed.
additive manufacturing↗
Synthesis and characterization of electron beam irradiation-induced damage in polycrystalline metal thin films
High-energy physics research, industrial sterilizing, and material processing depend extensively on electron beam accelerators. Exit windows are crucial components of such electron accelerator systems, maintaining vacuum integrity inside the machine while providing mechanical strength, thermal stability, and radiation resistance at the beam-target interface. In this study, thin metallic films of Ni, Ti, Cr, and V were explored for use in electron beam exit windows, and their properties were compared with the properties of their bulk counterparts. Simulation results of metal foils predicted Ti to exhibit less beam power dissipation compared to Ni. However, Ni possesses superior mechanical and structural properties compared to Ti. The performance of these films under electron beam irradiation was examined by depositing thin layers of these films on silicon and metallic substrates using magnetron sputtering and exposing them to e-beam irradiation in a controlled setup. The deposited films were subjected to a dose of approximately 66 kGy at a beam energy of 10 MeV and characterized prior to and postexposure to the beam using field emission scanning electron microscopy, atomic force microscopy, x-ray diffraction (XRD), and nanoindentation. Particular emphasis was given to characteristics like the grain structure, surface morphology, dislocation density, and hardness. XRD patterns revealed irradiation-induced changes in peak intensities, while the crystallinity remained largely unchanged. Nanoindentation results showed that the pristine and irradiated Ti and Ni films were twice as hard when compared to bulk Ti and Ni samples, regardless of the substrate type used (Si or bulk Ti, or Ni). These results emphasize the superior mechanical properties of thin metal films compared to their bulk counterparts. In conclusion, this study advances the optimization of thin film materials for robust and efficient e-beam applications, ensuring improved durability and operational reliability.
AFM↗
Testing in Support of Space Fission System Development and Qualification
Extensive data would be required for the qualification of a fission surface power (FSP) system. The strategy for qualifying a FSP system could have a significant programmatic impact. This paper explores potential options that could be used for qualifying FSP systems, including cost-effective means for obtaining required data. three methods for obtaining qualification data are analysis, non-nuclear testing, and nuclear testing. It has been over 40 years since the US qualified a space reactor for launch. During that time, advances have been made related to all three methods. Perhaps the greatest advancement has occurred in the area of computational tools for design and analysis. Tools that have been developed, coupled with modem computers, would have a significant impact on a FSP qualification. This would be especially true for systems with materials and fuels operating well within temperature, irradiation damage, and burnup limits. The ability to perform highly realistic non-nuclear testing has also advanced throughout the past four decades. Instrumented thermal simulators were developed during the 1970s and 1980s to assist in the development, operation, and assessment of terrestrial fission systems. Instrumented thermal simulators optimized for assisting in the development, operation, and assessment of modem FSP systems have been under development (and utilized) since 1998. These thermal simulators enable heat from fission to be closely mimicked (axial power profile, radial power profile, temperature, heat flux, etc.} and extensive data to be taken from the core region. Both steady-state and transient operation can be tested. For transient testing, reactivity feedback is calculated (or measured in cold/warm criticals) based on reactor temperature and/or dimensional changes. Pin power during a transient is then calculated based on the reactivity feedback that would occur given measured values of temperature and/or dimensional change. In this way nonnuclear testing can be used to provide very realistic information related to nuclear operation. Non-nuclear testing can be used at all levels, including component, subsystem, and integrated system testing. Realistic non-nuclear testing is most useful for systems operating within known temperature, irradiation damage, and burnup capabilities.
Houts, Mike↗
AMMT Round Robin 316H HFIR Irradiation Test Matrix and Readiness for Insertion
The Round Robin 316H HFIR-2 irradiation campaign, conducted under the Advanced Materials and Manufacturing Technologies (AMMT) Program, is designed to evaluate the variability in irradiation response of laser powder bed fusion (LPBF) stainless steel (SS)-316H across multiple national laboratories, powder heats, and processing conditions, with comparison to wrought counterparts. A total of 11 materials are intended for irradiation in the High Flux Isotope Reactor (HFIR), targeting two irradiation temperatures (400°C and 600°C) and one level of irradiation damage (2 dpa). This irradiation campaign utilizes the standardized general tensile (GENTEN) capsule design to accommodate subsized tensile specimens of these materials. Thermal analyses were performed to ensure appropriate temperature control by design and uniformity within the capsules. All the capsules for this irradiation except one have been successfully assembled, welded, and tested and are ready for HFIR insertion. The last capsule requires re-build following a failed weld. All eight capsules are intended to be inserted in HFIR cycle 517, which is scheduled to start September 8, 2026. This report summarizes the design, material selection, and readiness for insertion of the capsules.
36 MATERIALS SCIENCE↗
Study of drift-field solar cells damaged by low-energy protons Progress report, Sep. 10 - Oct. 15, 1965
Irradiation damage of drift-field solar cells by low energy protons - computer analysis of current-voltage and spectral response data
PROTON DAMAGE↗
Field and charge dependence of radiation damage in silicon.
Impurity concentration effect of electron irradiation damage in photovoltaic silicon cell with shallow p-n junction
SILICON↗
Diffusion-mediated chemical concentration variation and void evolution in ion-irradiated NiCoFeCr high-entropy alloy
High-entropy alloys (HEAs) are proposed as potential structural materials for advanced nuclear systems, but little is known about the response of matrix chemistry in HEAs upon irradiation. Here, we reveal a substantial change of matrix chemical concentration as a function of irradiation damage (depth) in equiatomic NiCoFeCr HEA irradiated by 3 MeV Ni ions. After ion irradiation, the matrix contains more Fe/Cr in depth shallower than ~900–1000 nm but more Ni/Co from ~900–1000 nm to the end of the ion-damaged region due to the preferential diffusion of vacancies through Fe/Cr. Preferential diffusion also facilitates migration of vacancies from high radiation damage region to low radiation damage region, leading to no void formation below ~900–1000 nm and void formation around the end of the ion-damaged region at a fluence of 5 × 10 16 cm -2 (~123 dpa, displacements per atom, peak dose under full cascade mode). As voids grow significantly at an increased fluence (8 × 10 16 cm -2 , 196 dpa), the matrix concentration does not change dramatically due to new voids formed below ~900–1000 nm.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Diffusion-mediated chemical concentration variation and void evolution in ion-irradiated NiCoFeCr high-entropy alloy
High-entropy alloys (HEAs) are proposed as potential structural materials for advanced nuclear systems, but little is known about the response of matrix chemistry in HEAs upon irradiation. Here, we reveal a substantial change of matrix chemical concentration as a function of irradiation damage (depth) in equiatomic NiCoFeCr HEA irradiated by 3 MeV Ni ions. After ion irradiation, the matrix contains more Fe/Cr in depth shallower than ~900–1000 nm but more Ni/Co from ~900–1000 nm to the end of the ion-damaged region due to the preferential diffusion of vacancies through Fe/Cr. Preferential diffusion also facilitates migration of vacancies from high radiation damage region to low radiation damage region, leading to no void formation below ~900–1000 nm and void formation around the end of the ion-damaged region at a fluence of 5 × 10 16 cm –2 (~123 dpa, displacements per atom, peak dose under full cascade mode). As voids grow significantly at an increased fluence (8 × 10 16 cm –2 , 196 dpa), the matrix concentration does not change dramatically due to new voids formed below ~900–1000 nm.
36 MATERIALS SCIENCE↗