Search NASA⌕ Search

SEARCH · Search NASA

Results for “L/D”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Benefits of high aerodynamic efficiency to orbital transfer vehicles

The benefits and costs of high aerodynamic efficiency on aeroassisted orbital transfer vehicles (AOTV) are analyzed. Results show that a high lift to drag (L/D) AOTV can achieve significant velocity savings relative to low L/D aerobraked OTV's when traveling round trip between low Earth orbits (LEO) and alternate orbits as high as geosynchronous Earth orbit (GEO). Trajectory analysis is used to show the impact of thermal protection system technology and the importance of lift loading coefficient on vehicle performance. The possible improvements in AOTV subsystem technologies are assessed and their impact on vehicle inert weight and performance noted. Finally, the performance of high L/D AOTV concepts is compared with the performances of low L/D aeroassisted and all propulsive OTV concepts to assess the benefits of aerodynamic efficiency on this class of vehicle.

Andrews, D. G.↗
NASA NTRS1990

Atmospheric effects on Martian aerocapture

A preliminary study of the effects of the atmosphere on Martian aerocapture has been completed at NASA-Johnson. Nominal cases were defined and several types of density dispersions utilized to show the effect of L/D ratio on aerocapture performance. Both open and closed loop three-degree-of-freedom simulations were developed. The open loop work demonstrated the reduction of the aerocapture corridor in the presence of density biases and shears. Closed loop runs were studied in the presence of shear-biases where the aerocapture trajectory was divided into three regions or phases. Each phase independently had a nominal density or a dispersed + 100 percent density. Two phase combinations were found to cause aerocapture failures with the three L/Ds considered: 0.3, 0.7, 1.0. There is a significant improvement in aerocapture performance as the L/D is increased from 0.3 to 0.7, but a much smaller increase in performance as the L/D is increased from 0.7 to 1.0. Based on current knowledge of the Martian atmosphere, a minimum L/D of 0.7 is recommended for early Mars missions.

Ess, Robert H.↗
NASA NTRS1992

Aerodynamics of the advanced launch system (ALS) propulsion and avionics (P/A) module

This paper discusses the design and testing of candidate Advanced Launch System (ALS) Propulsion and Avionics (P/A) Module configurations. The P/A Module is a key element of future launch systems because it is essential to the recovery and reuse of high-value propulsion and avionics hardware. The ALS approach involves landing of first stage (booster) and/or second stage (core) P/A modules near the launch site to minimize logistics and refurbishment cost. The key issue addressed herein is the aerodynamic design of the P/A module, including the stability characteristics and the lift-to-drag (L/D) performance required to achieve the necessary landing guidance accuracy. The reference P/A module configuration was found to be statically stable for the desired flight regime, to provide adequate L/D for targeting, and to have effective modulation of the L/D performance using a body flap. The hypersonic aerodynamic trends for nose corner radius, boattail angle and body flap deflections were consistent with pretest predictions. However, the levels for the L/D and axial force for hypersonic Mach numbers were overpredicted by impact theories.

Ferguson, Stan↗
NASA NTRS1993

Aerobraking technology studies

For a Mars Expedition, aerobrakes can play a vital role in several major mission events, including aerocapture to achieve orbit and descent to the planetary surface both at Mars and upon return to Earth. The feasibility of aerobrake designs will depend upon material and structures technologies because they will serve as a key factor in determining: (1) aerobrake mass and mass fraction; (2) the extent to which aerobrakes can survive the thermal environment. This is especially important for reusable aerobrakes. With the cancellation of the Aeroassist Flight Experiment, the effort to validate aerobrake designs has focused on laboratory test and analysis; (3) the feasibility of assembling and/or deploying large aerobrakes. On-orbit assembly is a critical issue for all spacecraft intended for Mars exploration missions. Current studies are addressing options related to inspace assembly and construction; and (4) configuration lift-to-drag (L/D) ratio. High L/D increases convective heating, whereas low L/D emphasizes radiative heating. In general, the lowest L/D design that can satisfy mission requirements is preferred.

Eldred, Charles H.↗
NASA NTRS2005

Entry, Descent, and Landing Technology Concept Trade Study for Increasing Payload Mass to the Surface of Mars

A trade study was conducted that compared various entry, descent, and landing technologies and concepts for placing an 1,800 kg payload on the surface of Mars. The purpose of this trade study was to provide data, and make recommendations, that could be used in making decisions regarding which new technologies and concepts should be pursued. Five concepts were investigated, each using a different combination of new technologies: 1) a Baseline concept using the least new technologies, 2) Aerocapture and Entry from Orbit, 3) Inflatable Aeroshell, 4) Mid L/D Aeroshell-A (high ballistic coefficient), and 5) Mid L/D Aeroshell-B (low ballistic coefficient). All concepts were optimized to minimize entry mass subject to a common set of key requirements. These key requirements were: A) landing a payload mass of 1,800 kg, B) landing at an altitude 2.5 km above the MOLA areoid, C) landing with a descent rate of 2.5 m/s, and D) using a single launch vehicle available within the NASA Expendable Launch Vehicle Contract without resorting to in-space assembly. Additional constraints were implemented, some common to all concepts and others specific to the new technologies used. Among the findings of this study are the following observations. Concepts using blunt-body aeroshells (1, 2, and 3 above) had entry masses between 4,028 kg and 4,123 kg. Concepts using mid L/D aeroshells (4 and 5 above) were significantly heavier with entry masses of 5,292 kg (concept 4) and 4,812 kg (concept 5). This increased weight was mainly due to the aeroshell. Based on a comparison of the concepts it was recommended that: 1) re-qualified and/or improved TPS materials be developed, 2) large subsonic parachutes be qualified. Aerocapture was identified as a promising concept, but system issues beyond the scope of this study need to be investigated. Inflatable aeroshells were identified as a promising new technology, but they require additional technology maturation work. For the class of missions investigated in this trade study, mid L/D aeroshells were not competitive on an entry mass basis as compared to blunt-body aeroshells.

Cruz, Juan R.↗
NASA NTRS2009

Cold-Flow Testing of a Proposed Integrated Center-Body Diffuser/Steam Blocker Concept for Plum Brook Station's B-2 Test Facility

The center-body diffuser (CBD) steam blocker (SB) system is a concept that incorporates a set of secondary drive nozzles into the envelope of a CBD, such that both nozzle systems (i.e., the rocket engine and the steam blocking nozzles) utilize the same supersonic diffuser, and will operate either singularly or concurrently. In this manner, the SB performs as an exhaust system stage when the rocket engine is not operating, and virtually eliminates discharge flow on rocket engine shutdown. A 2.25-percent scale model of a proposed SB integrated into a diffuser for the Plum Brook B-2 facility was constructed and cold-flow tested for the purpose of evaluating performance characteristics of various design options. These specific design options addressed secondary drive nozzle design (method of steam injection), secondary drive nozzle location relative to CBD throat, and center-body throat length to diameter (L/D) ratios. The objective of the test program is to identify the desired configuration to carry forward should the next phase of design proceed. The tested scale model can provide data for various pressure ratios; however, its design is based on a proposed B-2 spray chamber (SC) operating pressure of 4.0 psia and a steam supply pressure of 165 psia. Evaluation of the test data acquired during these tests indicate that either the discrete axial or annular nozzle configuration integrated into a CBD, with an annular throat length of 1.5 L/D at the nominal injection position, would be suitable to carry forward from the SB's perspective. Selection between these two then becomes more a function of constructability and implementation than performance. L/D also has some flexibility, and final L/D selection can be a function of constructability issues within a limited range.

Edwards, Daryl A.↗
NASA NTRS1975

Thermodynamic effects on developed cavitation

The results of an investigation of thermodynamic effects are presented. Distributions of temperature and pressure in a developed cavity were measured for zero- and quarter-caliber ogives. A semiempirical entrainment theory was developed to correlate the measured temperature depression in the cavity. This theory correlates the maximum temperature depression expressed in dimensionless form as the Jakob number in terms of the dimensionless numbers of Nusselt, Reynolds, Froude, and Peclet, and dimensionless cavity length, L/D. The results show that in general, the temperature depression increases with L/D and temperature and the cavitation number based on measured cavity pressure is a function of L/D for a given model contour, independent of the thermodynamic effect.

Holl, J. W.↗
NASA NTRS1980

A Summery of an In-flight Evaluation of Control System Pure Time Delays During Landing Using the F-8 DFBW Airplane

An in-flight investigation of the effect of pure time delays on low L/D space shuttle type landing tasks was undertaken. The results indicate that the sensitivity of the pilot ratings to changes in pure time delay in pitch is strongly affected by the task and only slightly affected by changes in control system augmentation mode. Low L/D spot landings from a lateral offset were twice as sensitive to pure time delay as normal low L/D landings. For comparison purposes, formation flying was also investigated, and was found to be less sensitive to time delay than the landing tasks.

Berry, D. T.↗
NASA NTRS1983

Minimum-fuel aeroassisted coplanar orbit transfer using lift-modulation

Minimum-fuel trajectories and lift controls are computed for aeroassisted coplanar transfer from high orbit to low orbit. The optimal aeroassisted transfer requires less fuel than the all-propulsive Hohmann transfer for a wide range of high orbit to low orbit transfers. The optimal control program for the atmospheric portion of the transfer is to fly at maximum positive L/D initially to recover from the downward plunge, and then, to fly at negative L/D to level off the flight, such that the vehicle skips out of the atmosphere with a flight path angle near zero degrees. To avoid excessive heating rates, the vehicle flies initially at high angle of attack in order to slow down higher in the atmosphere, allowing recovery from the downward plunge, which occurs subsequently using the maximum positive L/D, to take place at a lower atmospheric density, or equivalently, at a higher altitude.

Mease, K. D.↗
NASA NTRS1984

Low lift-to-drag aero-assisted orbit transfer vehicles

The results of systems analysis conducted on low life drag ratio (L/D) aero-assisted orbit transfer vehicle (AOTV's) are presented. The objectives for this class of vehicle and formulate technology development plans and funding levels to bring the required technologies to readiness levels, as well as develop a credible decision data base encompassing the entire range of low L/D concepts for use in future NASA Aeroassist Orbit Transfer Vehicles studies. Each candidate low L/D concept, the aerobrake, the lifting brake, and the aeromaneuvering concept could be made to work with technologies achievable by the early 1990's. All concepts require flexible structure with flexible thermal protection system (TPS) to be successfully integrated into the shuttle orbiter for launch, all required improvements in guidance and control to fly the dispersed atmospheres at high altitude, and all concepts had potential to evolve from ground-based to space-based operations.

Andrews, D. G.↗
NASA NTRS1985

Optimum configuration of high-lift aeromaneuvering orbital transfer vehicles in viscous flow

The results of an analysis to determine the geometrical configuration of an aeroassisted transfer vehicle with a high lift-to-drag ratio (L/D) are described and the constraints imposed on this type of entry vehicle are considered. The aerodynamic characteristics of three configurations, a flat-plate delta wing, a truncated straight cone, and a truncated bent biconic are compared. The effect of viscosity is included in the analysis which examines the rounding of the sharp leading edges. It is shown that, under the constraints of carrying a given volume in the dead air region, the values of L/D are similar for each configuration and that a small blunt leading edge only slightly affects each vehicle's aerodynamic performance, causing less than a 5 percent drop in L/D. The truncated bent biconic is found to be the only configuration that provides the necessary stabilizing moments.

Davies, C. B.↗
NASA NTRS1986

Rarefied flow lift-to-drag measurements of the Shuttle Orbiter

This report presents a discussion of the analysis and the results of sensitive micro-g accelerometry measurements on the Shuttle Orbiter in the rarefied flow flight regime, that is, from altitudes of 60 km to 160 km. A brief description of the experimental apparatus called High Resolution Accelerometer Package (HiRAP) is given along with a description of the ground processing to obtain the lift-to-drag ratio (L/D) from the flight measurements. The flight results of L/D from six missions are presented and discussed. Comparisons are made with preflight wind tunnel data in the near continuum viscous interaction regime and preflight analytical estimates in the rarefied transition regime. Excellent agreement is obtained between flight and wind tunnel data in the viscous regime, but differences are noted between flight and preflight predictions in the transition regime. Free molecule flow F/D data are also obtained on each mission. Comparisons of flight data with classical theory show that complete diffuse reflection is not an appropriate model for rarefied aerodynamic coefficient calculations, and, for the Shuttle, some specular fraction is required. Surface reflection laws are explored to define the sensitivity of the L/D measurements to gas-surface molecule interactions.

Blanchard, R. C.↗
NASA NTRS1987

Rarefied aerodynamics and upper atmospheric flight results from the Orbiter High Resolution Accelerometer Package experiment

Data from the High Resolution Accelerometer Package (HiRAP) experiment on the Space Shuttle Orbiter have been analyzed for 10 flights to produce lift-drag (L/D) ratios in the free molecule, transition, and continuum flow flight regimes. Freestream density is also obtained in the altitude range from 60 km to 160 km using an aerodynamic model based upon earlier flight analysis of accelerometer data. The results of the L/D analysis of the latest four flights have been compared with the aerodynamic model developed from the first six HiRAP missions. The new data agree with the established flight-derived model, thereby validating earlier analysis. However, the arithmetic mean of the 10 flight-derived L/D values in the free molecular flow regime is 0.053 (+ or - 0.1) as compared to the initial value of 0.10 (+ or - 0.3), determined from STS-6. Updates to the Orbiter aerodynamic model values and calibration factors have been incorporated into the density calculations for all 10 flights to provide realistic absolute density. The derived density altitude profiles, which have been normalized to the U.S. Standard Atmosphere 1976, are characterized by a large amplitude wave pattern relative to the standard as seen in the initial flight analysis.

Blanchard, R. C.↗
NASA NTRS1989

Aerodynamic requirements for a Mars rover/sample return aerocapture vehicle

The sensitivity of Martian aerocapture performance to L/D and flight path angle is studied. By adding the minimum energy constraint to the classical corridor width definition, an L/D of at least 0.8 was found to be necessary to ensure a 3.0-deg actual corridor width. The plane change desired during the aeropass was also found to affect L/D requirements.

Ess, Robert H., Jr.↗
NASA NTRS1990

Aerodynamic requirements of a manned Mars aerobraking transfer vehicle

In this investigation, entry corridor analyses are performed to identify the aerodynamic requirements of a manned Mars aerobraking transfer vehicle. The major emphasis is on identifying the required aerobrake hypersonic L/D to insure a successful aerocapture. Aerobraking entry requirements are also imposed on a set of interplanetary mission opportunities to demonstrate their effect on mission flexibility. Based on the requirements of a 1 deg corridor width, deceleration into a parking orbit witn an apoapsis altitude of 32,972 km, and a 5-g deceleration limit, a manned Mars aerobrake characterized by an L/D of at least 1.5 is required for entry velocities as high as 10.0 km/sec. Limiting the Mars entry velocity to values below 8.5 km/sec is shown to induce a minor restriction on mission flexibility while alleviating aerothermodynamic and vehicle packaging concerns; hence, Mars entry velocities in the range of 6.0-8.5 km/sec are suggested, and a manned Mars aerobrake characterized by an L/D between 0.3 and 0.5 is recommended.

Braun, Robert D.↗
NASA NTRS1991

Effect of lift-to-drag ratio upon pilot rating for a preliminary version of the HL-20 lifting body

A man-in-the-loop simulation study of the handling qualities of the HL-20 lifting body vehicle has been performed in a fixed-base simulation cockpit. The study was aimed at identifying opportunities to improve the original design of the vehicle from a handling qualities and landing performance perspective. A subsonic aerodynamic model of the HL-20 was used as a baseline, and visual approaches and landings were made at various vehicle lift-to-drag (L/D) ratios. It is concluded that there is a high degree of correlation between maximum L/D ratio and pilot rating. Using the pilot ratings Level 1, flying qualities were found to be possible for configurations with a maximum L/D ratio of 3.8 or higher.

Jackson, E. B.↗
NASA NTRS1991

Aerothermodynamic environments of aerobraking vehicles for manned Mars missions

The aerothermodynamic environments of manned spacraft aerobraking in the Martian and earth atmospheres are evaluated. Thermal performance of aerobrake concepts are examined for current cryogenic-aerobrake and advanced propulsion missions entailing three different modes of aerobraking: (1) aerocapture into an orbit about Mars, (2) descent and landing at Mars, and (3) Mars return direct entry at earth. Analyses for these vehicles and modes included both radiative and convective heating, where radiative heating is shown to be a significant portion of the total stagnation point heating induced on the vehicle. A comprehensive parametric study of the effects of ballistic coefficient, nose radius, entry velocity, and L/D on stagnation point heating is described. Optimal nose radii for ranges of ballistic coefficient and entry velocity are determined. The peak heating rates are shown to be 83 W/sq cm and 90 W/sq cm for a low and high L/D Mars transfer vehicle configuration, respectively. Heating profiles for these vehicles using boundary layer techniques show that a high L/D shape will result in a smaller high-temperature region provided the flow is laminar. An examination of a crew return vehicle for a Mars return direct entry trajectory shows that the thermal protection for this aerobrake will require an ablative material for heat rejection due to the large heating rates (about 1 kW/sq cm).

Ledoux, Stephen T.↗
NASA NTRS1991

Aerodynamic characteristics of the HL-20 and HL-20A lifting-body configurations

The data show that the HL-20 is longitudinally and laterally stable over the test range from Mach 10 to 0.2. At hypersonic speeds it has a trimmed lift/drag ratio of 1.4. This values gives the vehicle a cross range capability similar to that of the Space Shuttle. At subsonic speeds, the HL-20 has a trimmed lift/drag ratio of about 3.6. Replacing the flat plate outboard fins with fins having an airfoil shape, increased the maximum trimmed L/D to 4.3. Preliminary evaluation of configuration modifications (the HL-20A series), indicates that trim at higher values of lift at hypersonic speeds could be achieved with an L/D of about 1.0. In the supersonic range, the lift and directional stability characteristics were improved. The untrimmed subsonic L/D was increased to 5.8 with airfoil fins.

Ware, George M.↗