Search NASA⌕ Search

SEARCH · Search NASA

Results for “LAMINAR BOUNDARY LAYER SEPARATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Transition and separation control on a low-Reynolds number airfoil

The major problem associated with the aerodynamic performance of airfoils at low Reynolds numbers is the presence of extensive laminar boundary-layer separation resulting in a large increase in presssure drag and a decrease in lift. The rapid deterioration in airfoil characteristics can be largely eliminated by artificially controlling the flow through the introduction of suitable disturbances in the boundary layer such that transition occurs ahead of the anticipated laminar separation. This paper presents the results of wind-tunnel tests conducted on a 10-cm model of LRN (1)-1007 airfoil with passive (roughness trips) and active (acoustic excitation) controls to trigger transition and suppress separation. Significant improvements in the aerodynamic characteristics of the airfoil were observed. Results of this study for a chord Reynolds number range of 40,000 to 250,000 are presented in this paper.

Mangalam, S. M.↗
NASA NTRS1952

Transition caused by the laminar flow separation

An experimental investigation of the effects of the geometry of body surface, Reynolds number, stream turbulence, and a roughness element (wire) on the reattachment of separated laminar boundary-layer flow on a bent flat plate is presented and discussed. The flow mechanisms determining reattachment of the boundary layer are analyzed and discussed.

BOUNDARY LAYER CHARACTERISTICS - WING SECTIONS↗
NASA NTRS1976

Upper wing surface boundary layer measurements and static aerodynamic data obtained on a 0.015-scale model (42-0) or the SSV orbiter configuration 140A/B in the LTV HSWT at a Mach number of 4.6 (LA58)

The purpose of the test was to investigate the nature of the Orbiter boundary layer characteristics at angles of attack from -4 to 32 degrees at a Mach number of 4.6. The effect of large grit, employed as transition strips, on both the nature of the boundary layer and the force and moment characteristics were investigated along with the effects of large negative elevon deflection on lee side separation. In addition, laminar and turbulent boundary layer separation phenomena which could cause asymmetric flow separation were investigated.

Ball, J. W.↗
NASA NTRS1989

Critical Evaluation of the Conference on Low Reynolds Number Aerodynamics at the University of Notre Dame

As a result of the continued interest in designing efficient low Reynolds number systems, the University of Notre Dame decided to organize a Conference on Low Reynolds Number Aerodynamics in June 1989. This Conference followed the 1986 International Conference in London by about three years and the first Conference on Low Reynolds Number Airfoil Aerodynamics at Notre Dame in 1985 by four years. The emphasis of the 1989 Conference was to assess the state-of-the-art in the chord Reynolds number range from about 10,000 to about 700,000. Applications of current interest include high altitude remotely or robotically piloted vehicles, ultra-light, and human powered vehicles as well as mini-RPVs at low altitudes. Other examples include small axial-flow fans used to cool electronic equipment in the unpressurized sections of high-altitude aircraft and gas turbine blades. High Reynolds number airfoil design strategies attempt to control the onset and development of turbulent boundary layers. This is difficult at low Reynolds numbers because of the increased stability of attached laminar boundary layers. Therefore, laminar separation is common even at small angles of attack at low Reynolds numbers. Under these conditions, the development of a turbulent boundary layer usually depends on the formation of a transitional separation bubble. The purpose of this Conference on Low Reynolds Number Aerodynamics was to bring together those researchers who have been active in areas closely related to this subject. It is clear from the papers presented that a great deal of progress has been made in understanding the occurrence and behavior of laminar separation and transition as well as their overall effect on the performance of airfoils at low chord Reynolds numbers. This progress has brought us closer to our goal of improving analytical methods for the design and evaluation of a variety of practical applications.

Mueller, Thomas J.↗
NASA NTRS2018

Scale-Resolving Simulations of Low-Pressure Turbine Cascades with Wall Roughness Using A Spectral-Element Method

The accurate prediction of wall-roughness effects in turbomachinery is becoming critical as turbine designers address airfoil surface quality and degradation concerns arising from the shift to advanced ceramic matrix composite (CMC) or additively-manufactured airfoils operating in higher temperature environments. In this paper, a recently developed computational capability for accurate and efficient scale-resolving simulations of turbomachinery is extended to analyze the boundary- layer separation and transition characteristics in a rough-wall low-pressure turbine (LPT) cascade. The computational capability is based on an entropy-stable discontinuous-Galerkin spectral-element approach that extends to arbitrarily high orders of spatial and temporal accuracy, and is implemented in an efficient manner for a modern high performance computer architecture. Results from the scale-resolving simulations of both smooth and rough airfoil cascades are presented and compared to previous experiments and numerical simulations. The results show that the suction surface boundary layer undergoes laminar separation, transition, and turbulent reattachment for the smooth airfoil cascade, while in the presence of roughness the separation and transition behavior of the suction surface boundary layer is substantially modified. The differences between the smooth and rough airfoil cascades are then highlighted by a detailed analysis of their respective turbulent flow fields.

Spectral-Element↗
NASA NTRS1994

Crossflow instability control on a swept-wing: Preliminary studies

The pressure distribution on a swept wing causes the streamlines at the edge of the boundary layer to be curved. This pressure gradient normal to the external streamline creates a velocity component normal to the external streamline within the boundary layer which is referred to as the crossflow velocity. Because the crossflow velocity profile perpendicular to the wing surface has an inflection point, the profile is unstable. The stationary instability mode takes the form of crossflow vortices. Under these conditions, the boundary layer on the wing is extremely unstable and transition to turbulent flow takes place much closer to the leading edge of the wing than it would on an unswept wing. Higher skin friction drag is associated with turbulent flow, and so better aircraft performance could be obtained if the crossflow could be eliminated One method of controlling crossflow that is being investigated is boundary-layer suction. An extensive airfoil suction experiment in the 8 feet Transonic Pressure Tunnel (TPT) at NASA Langley Research Center will begin late in 1994. Because of the size, complexity, and expense associated with this test, a number of 'risk-reduction' tests are currently being conducted. The 20 x 28 in. Shear Flow Control Tunnel at NASA Langley is being used for some of these tests. Prior to the summer of 1994, a flat plate with a swept leading edge was installed in the 20 x 28 in. tunnel, with a displacement body mounted on the tunnel ceiling that created a pressure distribution on the plate similar to the pressure distribution on a swept wing. The flow over the plate was investigated during the summer of 1994 using a laser Doppler velocimeter (LDV) system. The LDV measurements indicated the possible presence of multiple disturbance modes, a rarely-seen phenomena since, in most tests, one disturbance mode dominates. The possible existence of multiple disturbance modes in the flat plate boundary layer, however, means that the flow in the 20 x 28 in. tunnel is of interest itself, and will be investigated more thoroughly in the future. With a view to these investigations, the boundary layer traverse mechanism in the 20 x 28 in. tunnel was modified to improve its performance, and strain gauges were mounted on the traverse in order to monitor its deflection during a test. Other preliminary work conducted in the 20 x 28 in. tunnel included the use of an infrared camera system. Previous work with this system showed that transition indeed could be detected, but the signal produced by the crossflow vortices was too weak to be detected. It was hoped that spraying the flat plate with naphthalene would augment the heat transfer associated with the crossflow vortices so that they would show up in a IR image; however, experiments showed that this would not work. Another set of tests was conducted in the 20 x 28 in. tunnel to determine the tripping requirements for a set of airfoil-shaped struts that will be used in the 8 feet TPT experiment. Since the Reynolds number associated with these struts is small, a laminar boundary layer would separate early, causing large fluctuations in the flow field. A turbulent boundary layer would remain attached further back, but tripping from laminar to turbulent flow at low Reynolds number is very difficult. However, trip strip configurations were found that should effectively trip the boundary layer at the required conditions. Currently underway is an investigation of the data acquisition requirements for the 8 feet TPT experiment, with the purpose of the finding the minimum amount of data needed to characterize sufficiently the swept-wing boundary layer. This study is being conducted using a numerically generated data set.

Bridges, David H.↗
NASA NTRS1992

Plume effects on the flow around a blunted cone at hypersonic speeds

Tests at M = 8.2 show that a simulated rocket plume at the base of a blunted cone can cause large areas of separated flow, with dramatic effects on the heat transfer rate distribution. The plume was simulated by solid discs of varying sizes or by an annular jet of gas. Flow over the cone without a plume is fully laminar and attached. Using a large disc, the boundary layer is laminar at separation at the test Reynolds number. Transition occurs along the separated shear layer and the boundary layer quickly becomes turbulent. The reduction in heat transfer associated with a laminar separated region is followed by rising values as transition occurs and the heat transfer rates towards the rear of the cone substantially exceed the values obtained without a plume. With the annular jet or a small disc, separation occurs much further aft, so that heat transfer rates at the front of the cone are comparable with those found without a plume. Downstream of separation the shear layer now remains laminar and the heat transfer rates to the surface are significantly lower than the attached flow values.

Atcliffe, P.↗
NASA NTRS1986

Low-Reynolds number aerodynamics research at NASA Langley Research Center

The present status of various types of low-Reynolds number aerodynamics research being conducted at the Fluid Dynamics Branch of NASA Langley Research Center is reviewed. The facilities, testing techniques, airfoil design, and experimental verification are addressed, and ongoing studies of laminar separation bubbles, boundary layer stability and transition control, and low-Reynolds number juncture flow are discussed. The possibility of improving vehicle characteristics at low Reynolds numbers and the general trends of the most promising research in these areas are examined.

Harvey, William D.↗
NASA NTRS1990

Modelling the transitional boundary layer

Recent developments in the modelling of the transition zone in the boundary layer are reviewed (the zone being defined as extending from the station where intermittency begins to depart from zero to that where it is nearly unity). The value of using a new non-dimensional spot formation rate parameter, and the importance of allowing for so-called subtransitions within the transition zone, are both stressed. Models do reasonably well in constant pressure 2-dimensional flows, but in the presence of strong pressure gradients further improvements are needed. The linear combination approach works surprisingly well in most cases, but would not be so successful in situations where a purely laminar boundary layer would separate but a transitional one would not. Intermittency-weighted eddy viscosity methods do not predict peak surface parameters well without the introduction of an overshooting transition function whose connection with the spot theory of transition is obscure. Suggestions are made for further work that now appears necessary for developing improved models of the transition zone.

Narasimha, R.↗
NASA NTRS1949

Aerodynamic Study of a Wing-fuselage Combination Employing a Wing Swept Back 63 Degrees : Characteristics at a Mach Number of 1.53 Including Effect of Small Variations of Sweep

Measured values of lift, drag, and pitching moment at a Mach number of 1.53 and Reynolds numbers of 0.31, 0.62, and 0.84 million are presented for a wing-fuselage combination having a wing leading-edge sweep angle of 63 degrees, an aspect ratio of 3.42, a taper ratio of 0.25, and an NACA 64A006 section in the stream direction. Data are also presented for sweep angles of 57.0 degrees, 60.4 degrees, 67.0 degrees, and 69.9 degrees. The experimentally determined characteristics were less favorable than indicated by the linear theory but the experimental and theoretical trends with sweep were in good agreement. Boundary-layer-flow tests showed that laminar boundary-layer separation was the primary cause of the differences between experiment and theory.

REYNOLDS NUMBER EFFECTS - COMPLETE WING↗
NASA NTRS1976

Three-dimensional boundary layers approaching separation

The theory of semi-similar solutions of the laminar boundary layer equations is applied to several flows in which the boundary layer approaches a three-dimensional separation line. The solutions obtained are used to deduce the nature of three-dimensional separation. It is shown that in these cases separation is of the "ordinary" type. A solution is also presented for a case in which a vortex is embedded within the three-dimensional boundary layer.

Williams, J. C., III↗
NASA NTRS1985

Flight-measured laminar boundary-layer transition phenomena including stability theory analysis

Flight experiments were conducted on a single-engine turboprop aircraft fitted with a 92-in-chord, 3-ft-span natural laminar flow glove at glove section lift coefficients from 0.15 to 1.10. The boundary-layer transition measurement methods used included sublimating chemicals and surface hot-film sensors. Transition occurred downstream of the minimum pressure point. Hot-film sensors provided a well-defined indication of laminar, laminar-separation, transitional, and turbulent boundary layers. Theoretical calculations of the boundary-layer parameters provided close agreement between the predicted laminar-separation point and the measured transition location. Tollmien-Schlichting (T-S) wave growth n-factors between 15 and 17 were calculated at the predicted point of laminar separation. These results suggest that for many practical airplane cruise conditions, laminar separation (as opposed to T-S instability) is the major cause of transition in predominantly two-dimensional flows.

Obara, C. J.↗
NASA NTRS1981

Experimental investigation of the flow on the suction side of a thin Delta wing

Surface oil flow patterns were photographed and pressure distribution measurements were carried out on a sharp edged delta wing of aspect ratio lambda = 1.0 in order to determine the influence of Reynolds number and of vortex breakdown on the flow on the suction side of the wing. The formation of the secondary vortex occurs due to separation of a laminar boundary layer in the front part of the wing and due to separation of a turbulent boundary layer in the rear part of the wing. In the case of turbulent separation, the secondary separation line is closer to the wing leading edge than in the laminar case. The position of the transition depends on the Reynolds number and on the angle of incidence. The breakdown of a vortex above the wing leads to a kink in the secondary separation line.

Hummel, D.↗
NASA NTRS1989

Analysis of low Reynolds number separation bubbles using semiempirical methods

The formation and growth of transitional separation bubbles can significantly affect boundary-layer development on airfoils operating at low chord Reynolds numbers. Of primary concern is the change in boundary-layer thickness between laminar separation and turbulent reattachment. This can be estimated using semiempirical methods, such as the one devised by Horton (1968), which are based on solutions to the integral forms of the boundary-layer equations. The applicability of these methods at low Reynolds numbers was investigated using hot-wire measurements of bubbles formed on an NACA 66(3)-018 airfoil at chord Reynolds numbers of 50,000-200,000. The momentum thickness growth between separation and transition was found to be similar to that predicted for a laminar half-jet and appears to be influenced by the momentum thickness Reynolds number at separation. This parameter also was found to have a noticeable effect on the Reynolds number based on the length of a bubble's laminar portion.

Schmidt, Gordon S.↗