Search NASA⌕ Search

SEARCH · Search NASA

Results for “Laminar Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Assessment of the Amplification Factor Transport Transition Model for High-Mach Number Flows

In its present state, the Amplification Factor Transport (AFT) model provides an efficient alternative for high-fidelity stability methods for complex geometries subject to low-speed conditions considered in the industrial-production CFD environment. Its performance has not yet been documented for the typical transition scenarios in hypersonic conditions. The goal of the present study is to apply the AFT model to a yawed- and flared-cone configuration, for which the laminar flows respectively support the crossflow and second-mode instability mechanisms, and to compare the amplification results against high-fidelity results computed with Linear Parabolized Stability Equations (LPSE). High-resolution viscous-flow solutions are provided with OVERFLOW and COFFE. For the yawed-cone case, the AFT model yields the largest amplification in a region of the flow where the expected crossflow instability is not amplified (in the leeward symmetry plane) according to LPSE. For the flared-cone case with a wall-temperature slightly lower than the adiabatic value, the AFT model yields extremely large amplification factors (in excess of 100), exceeding the computed LPSE amplification of second-mode instability results by a factor 14. Upon considering a cold-wall condition, the model shows much smaller amplification factors, which is the opposite with respect to the expected behavior of the second mode. The AFT model does not adequately capture the crossflow and second-mode instability mechanisms in its present state.

Groot, Koen J.↗
DOE OSTI2022

Non-Boussinesq subgrid-scale model with dynamic tensorial coefficients

A major drawback of Boussinesq-type subgrid-scale stress models used in large-eddy simulations is the inherent assumption of alignment between large-scale strain rates and filtered subgrid-stresses. A priori analyses using direct numerical simulation (DNS) data have shown that this assumption is invalid locally as subgrid-scale stresses are poorly correlated with the large-scale strain rates [J. Bardina, J. Ferziger, and W. Reynolds, Improved subgrid-scale models for large-eddy simulation, in Proceedings of the 13th Fluid and Plasmadynamics Conference, AIAA (1980); C. Meneveau and K. Katz, Scale-invariance and turbulence models for large-eddy simulation, Ann. Rev. Fluid Mech. 32, 1 (2000)]. In the present work, a new, non-Boussinesq subgrid-scale model is presented where the model coefficients are computed dynamically. Some previous non-Boussinesq models have observed issues in providing adequate dissipation of turbulent kinetic energy [e.g., Bardina et al., Proceedings of the 13th Fluid and Plasmadynamics Conference (1980); R. A. Clark, J. Ferziger, and W.C. Reynolds. Evaluation of subgrid-scale models using an accurately simulated turbulent flow, J. Fluid Mech. 91, 1 (1979); S. Stolz and N. A. Adams, An approximate deconvolution procedure for large-eddy simulation, Phys. Fluids 11, 1699 (1999)]; however, the present model is shown to provide sufficient dissipation using dynamic coefficients. Modeled subgrid-scale Reynolds stresses satisfy the consistency requirements of the governing equations for large-eddy simulation (LES), vanish in laminar flow and at solid boundaries, and have the correct asymptotic behavior in the near-wall region of a turbulent boundary layer. The new model, referred to as the dynamic tensor-coefficient Smagorinsky model (DTCSM), has been tested in simulations of canonical flows: decaying and forced homogeneous isotropic turbulence, and wall-modeled turbulent channel flow at high Reynolds numbers. The results show favorable agreement with DNS data. It has been shown that DTCSM offers similar predictive capabilities as the dynamic Smagorinsky model for canonical flows. In order to assess the performance of DTCSM in more complex flows, wall-modeled simulations of high Reynolds number flow over a Gaussian bump (Boeing speed bump) exhibiting smooth-body flow separation are performed. Predictions of surface pressure and skin friction, compared against DNS and experimental data, show improved accuracy from DTCSM in comparison to existing static coefficient (Vreman) and dynamic Smagorinsky model. The computational cost of performing LES with this model is up to 15% higher than the dynamic Smagorinsky model.

42 ENGINEERING↗
DOE OSTI2021

Graph convolutional networks applied to unstructured flow field data

Abstract Many scientific and engineering processes produce spatially unstructured data. However, most data-driven models require a feature matrix that enforces both a set number and order of features for each sample. They thus cannot be easily constructed for an unstructured dataset. Therefore, a graph based data-driven model to perform inference on fields defined on an unstructured mesh, using a graph convolutional neural network (GCNN) is presented. The ability of the method to predict global properties from spatially irregular measurements with high accuracy is demonstrated by predicting the drag force associated with laminar flow around airfoils from scattered velocity measurements. The network can infer from field samples at different resolutions, and is invariant to the order in which the measurements within each sample are presented. The GCNN method, using inductive convolutional layers and adaptive pooling, is able to predict this quantity with a validation R 2 above 0.98, and a Normalized Mean Squared Error below 0.01, without relying on spatial structure.

Ogoke, Francis (ORCID:0000000224327783)↗
DOE OSTI2020

Controllable vortex shedding from dissipative exchange flows in ferromagnetic channels

Ferromagnetic channels subject to spin injection at one extremum sustain long-range coherent textures that carry spin currents known as dissipative exchange flows (DEFs). In the weak injection regime, spin currents carried by DEFs decay algebraically and extend through the length of the channel, a regime known as spin superfluidity. Similar to fluids, these structures are prone to phase slips that manifest as vortex-antivortex pairs. In this work, we numerically study vortex shedding from DEFs excited in a magnetic nanowire with a physical obstacle. Using micromagnetic simulations, we find regimes of laminar flow and vortex shedding as a function of obstacle position tunable by the spin injection sign and magnitude. Vortex-antivortex pairs translate forward (VF regime) or backward (VB regime) with respect to the detector's extremum, resulting in well-defined spectral features. Qualitatively similar results are obtained when temperature, anisotropy, and weak nonlocal dipole fields are included in the simulations. These results provide clear features associated with DEFs that may be detected experimentally in devices with nominally identical boundary conditions. Furthermore, our results suggest that obstacles can be considered as DEF control gates, opening an avenue to manipulate DEFs via physical defects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Fractal Model for Drag Reduction on Multiscale Nonwetting Rough Surfaces

Rough surfaces in contact with a flow of fluid exhibit alternating no-slip and free shear boundary conditions at the solid–liquid and air–liquid interfaces, respectively, thereby potentially offering drag reduction benefits. The balance between the dynamic pressure in the flow and the restoring capillary pressure in the interasperity spaces determines the stability of the Cassie state of wettability and is a function of the relative extent of no-slip and free shear regions per unit surface area. In the present study, using a fractal representation of rough surface topography, an analytical model is developed to quantify the stability of the Cassie state of wettability as well as drag reduction and the friction factor for laminar flow in a rectangular channel between nonwetting multiscale rough surfaces. A systematic study is conducted to quantify the effects of fractal parameters of the surfaces and the flow Reynolds number on drag reduction and the friction factor. The studies are used to develop friction factor curves extending the classical Moody diagram to hydrophobic and superhydrophobic surfaces. On the basis of the studies, regime maps are derived for estimating the extent of drag reduction offered by hydrophobic and superhydrophobic surfaces, revealing that superhydrophobic surfaces do not always offer the best drag reduction performance. The application of the fractal model to practical topographies of nonwetting surfaces of copper, aluminum, and zinc oxide fabricated via electrodeposition and etching is also discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Flow Reactor Study of the Soot Precursors of Novel Cycloalkanes as Synthetic Jet Fuel Compounds: Octahydroindene, p -Menthane, and 1,4-Dimethylcyclooctane

Sustainable aviation fuels (SAFs) or Synthetic aviation turbine fuels (SATFs) derived from nonpetroleum sources are essential for energy security and a strong rural and agricultural economy. Airplanes operating on SAF can have lower particle emissions compared to those of conventional jet fuel, reducing air quality impacts near airports. Processing biobased isoprene or wood and agricultural waste can produce cycloalkane-rich fuels with properties meeting ASTM International’s SATF requirements. The unique structures of these cycloalkanes yield lower soot emissions because of their lack of aromatic rings. We measured the soot formation tendency as yield sooting index (YSI) and used laminar flow reactor experiments to evaluate soot precursors formed for isoprene-derived compounds p-menthane and 1,4-dimethylcyclooctane (DMCO), and octahydroindene (OHI)─ produced from woody biomass via catalytic fast pyrolysis. The combustion chemistry of the OHI and DMCO has not been previously studied. Experiments were conducted at 10 bar from 800 to 1200 K, equivalence ratios of 1.0 and 3.0, and residence times of 1.0 and 0.6 s, respectively. Experimentally detected species were used to elucidate the mechanisms of soot precursor formation. OHI exhibited the highest YSI (94.5) and formed a high concentration of benzene primarily by direct dehydrogenation of the six-membered ring. p-Menthane (YSI 92.0) and DMCO (YSI 85.0) oxidation products included fewer aromatic components but higher benzene precursors, including 1,3-butadiene, propyne, and allene. This suggests that the ring-opening pathway is dominant over the dehydrogenation pathway in the benzene formation for these compounds. This experimental speciation provides insight into the influence of the cycloalkane structure on the sooting tendencies of potential SAF blend components, thereby aiding in fuel design processes.

09 BIOMASS FUELS↗
DOE OSTI2022

Pressure drop and heat transfer characteristics of nitrate salt and supercritical CO 2 in a diffusion-bonded heat exchanger

A lab-scale 316/L stainless steel diffusion-bonded heat exchanger was examined within a coupled high-temperature test facility consisting of an atmospheric-pressure nitrate salt loop and a supercritical carbon dioxide (sCO 2 ) loop operating between 10 and 16 MPa. Pressure loss measurements collected for flow rates up to 0.55 kg/s of Solar Salt and up to 0.6 kg/s of carbon dioxide were used to generate friction factor correlations for the respective circular and semicircular zig-zag flow passages. Heat transfer measurements were also performed over a wide range of conditions to produce Nusselt correlations for the CO 2 and nitrate salt geometries. The Nusselt number is deduced from a heat transfer resistance network and overall conductance measurements collected across the operating envelope of the coupled sCO 2 – nitrate salt test facility. The CO 2 side correlation showed excellent agreement with existing correlations in the literature. Further, the salt side, having nearly circular channels with a different zig-zag angle and hydraulic diameter, yielded a new correlation applicable to the laminar flow regime. To examine the similitude of the friction correlations, pressure drop testing with water was performed on both sides of the component as well. Finally, results from non-destructive examination are discussed to provide insights regarding inspection methods and draining performance of high-temperature liquids in compact heat exchangers.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Radiative Heat Transport and Optical Characterization of High Temperature Molten Salts

The goal of this project was to advance the field of molten fluoride radiative heat transfer (RHT), through optical property measurements, heat transfer loop construction and operation, and computational fluid dynamics simulations. The following outcomes have been accomplished. A comprehensive review has been conducted to compile all available RHT-relevant optical absorption data for molten fluorides. The various measurement methods have also been compiled and critiqued. Thermal emission measurement methods have been refined and documented. A unique thermal emissivity measurement facility has been constructed and used to measure the emissivity of flowing FLiBe-exposed SS316 samples. A slight increase has been observed in the emissivity compared to unexposed SS316. A dual reflectance-emission setup was partially demonstrated for the purpose of molten fluoride absorption measurement. Preliminary infrared edge data for FLiNaK was obtained. A visible near-infrared (NIR) measurement setup has been constructed and will be used to measure absorption of corrosion products in FLiBe. A new multi-band thermal radiation method using blackbody-weighted spectral bands for the absorption-coefficient was deployed to investigate the thermal performance of the UW Natural Circulation FLiBe Loop under various power levels and operating conditions. The results showed an increasing and decreasing trend in the overall heat transfer with optical thickness with a maximum at optical thickness τ D ≈Ο(1). A forced convection FLiBe loop was constructed for the purpose of studying corrosion and thermal hydraulic phenomena. A vertical cantilever pump is used to achieve up to 5 gpm and 5 m/s flow velocity in hot and cold test sections. A methodology has been established for modeling radiative heat transfer (RHT) in molten salt coolants for the purpose of quantifying the contribution of thermal radiation in conditions relevant to FHR or MSR systems. The comparison between the results obtained for forced and mixed convection showed that in the studied ranges of optical thickness, the maximum effect of RHT on overall heat transfer was 60% improvement observed at z/D = 250 for forced convection; whereas for mixed convection, that value was higher at 170% observed at z/D = 30. The highest effect of RHT on the overall energy distribution was observed at τ D ≈3.4. Negligible effect (<20%) was observed above τ D =18 and below τ D ≈0.002. A CFD code-to-code comparison was conducted using COMSOL Multiphysics at UW-Madison and STAR-CCM at MIT, for a forced and mixed convection laminar flow for a grey medium in a vertical heated using both COMSOL Multiphysics at UW-Madison and STAR-CCM at MIT. The relative error was the largest at τ D =40 for the radiative heat flux, bulk temperature, and Nusselt number. On the other hand, the relative error was the least at τ D =0.002 for the conductive heat flux, bulk temperature, and Nusselt number.

Anderson, Mark↗
DOE OSTI2020

Electrical monitoring of saline tracers to reveal subsurface flow pathways in a flat ditch-drained field

Time-lapse electrical resistivity imaging (ERI) combined with salt tracers can enhance our understanding of subsurface flow and transport in ditch-drained agroecosystems. In a nearly level field adjacent to a drainage ditch, we installed 192 electrodes in a 72-m2 plot along with five hydrometric stations to enable time-lapse ERI monitoring during storms. Immediately prior to a wintertime rainstorm, we applied 5 kg of KBr to a shallow trench located roughly 11 m upgradient from the ditch. Antecedent conditions prior to the storm were wet, assuring a hydrologically connected state that favored tracer dissolution and movement in the subsurface. We monitored the evolution of the tracer plume with ERI over a seven-day period. Four-dimensional (4D) delineation of precipitation and tracer transport using time-lapse ERI showed that the tracer plume moved preferentially downward through a discontinuity in the argillic horizon within the first 57 hrs. Over the following 79 hrs, the tracer plume exhibited steady, lateral movement towards the drainage ditch within a more permeable sandy horizon situated just below the argillic. A spatial moment analysis of logarithmic changes in conductivity in the sand layer revealed seepage velocities ranging from 0.0027 to 0.0482 m d-1; these values were positively correlated with hydraulic gradients, suggesting laminar flow processes typical of sandy aquifers. Increasing groundwater velocities with hydraulic gradients suggest that solute transfers from groundwater to ditch are likely to be faster in storms, especially during wet periods. Even so, predominantly slow lateral transport within the sandy horizon, even during storms, indicates that critical source areas of pollutant loss are likely within a few meters of the ditch.

Robinson, Judith L.↗
DOE OSTI2023

Colloidal State Machines as Smart Tracers for Chemical Reactor Analysis

A widely utilized tool in reactor analysis is passive tracers that report the residence time distribution, allowing estimation of the conversion and other properties of the system. Recently, advances in microrobotics have introduced powered and functional entities with sizes comparable to some traditional tracers. This has motivated the concept of Smart Tracers that could record the local chemical concentrations, temperature, or other conditions as they progress through reactors. Herein, the design constraints and advantages of Smart Tracers by simulating their operation in a laminar flow reactor model conducting chemical reactions of various orders are analyzed. It is noted that far fewer particles are necessary to completely map even the most complex concentration gradients compared with their conventional counterparts. Design criteria explored herein include sampling frequency, memory storage capacity, and ensemble number necessary to achieve the required accuracy to inform a reactor model. Cases of severe particle diffusion and sensor noise appear to bind the functional upper limit of such probes and require consideration for future design. The results of the study provide a starting framework for applying the new technology of microrobotics to the broad and impactful set of problems classified as chemical reactor analysis.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

High‐pressure oxidation of n ‐butane

Abstract The oxidation of n ‐butane at elevated pressures has been investigated by experiments in a laminar flow reactor at 100 bar and temperatures of 450–900 K. The onset temperature for reaction increased from 550 K under oxidizing conditions (Φ = 0.02) to 625 K under reducing conditions (Φ = 13). NTC behavior was observed at 600–650 K (Φ = 0.02) and 625–675 K (Φ = 1.0). A detailed chemical kinetic model for the oxidation of n ‐butane was established. The present model and those suggested in literature were evaluated against the present experimental results and literature data at elevated pressures. None of the tested models could accurately reproduce the NTC behavior of n ‐butane under stoichiometric conditions of the present study, but all evaluated models could reproduce experimental data from literature with different levels of accuracy.

Hashemi, Hamid↗
DOE OSTI2022

Machine learning-based optimization of air-cooled heat sinks

Machine learning-based models using Artificial Neural Network (ANN) and greedy search algorithm are used to optimize air-cooled parallel plate-finned heat sinks (PPFHSs) subjected to laminar flow over an extensive range of design parameters. Here, the thermal and hydraulic performances of PPFHSs are represented by heat transfer coefficient (h) and pressure drop (ΔP), respectively. Optimization objectives for PPFHS designs can vary from industry to industry depending on their design priorities. The present study proposes a novel and generalized optimization method that defines practical optimization objectives and provides an accurate optimization process to design effective PPFHSs for a wide range of industrial applications with different design requirements. Three optimization objectives are presented in this study: (i) the largest h PΔ, (ii) the largest h within a specified maximum allowed flow rate, and (iii) the lowest weight that maximizes h for operation within the maximum allowed flow rate. While the shortcoming of the first objective is demonstrated, the other two objectives are found to be suitable for designing effective heat sinks (HSs) across different applications. Results suggest a promising trend from the third objective to develop HSs with ~ 37-68% lower weight, 80-85% reduced ΔP, and negligible penalty in h compared with optimized HSs obtained from the second objective. However, since the third objective leads to HSs with thinner fins, structural analysis should be performed to ensure reliable operation of the HSs.

42 ENGINEERING↗
DOE OSTI2026

Design and demonstration of a direct air capture system with moisture-driven CO 2 delivery into aqueous medium

Two direct air capture (DAC) systems were designed and demonstrated to passively capture CO 2 from ambient air and use moisture to release the CO2 into an alkaline medium. A bench-scale system delivering ∼1 g CO 2 d –1 was demonstrated in a laminar flow hood, and a small pilot-scale system that could deliver ∼100 g CO 2 d –1 was operated outdoors in a 4.2 m 2 raceway pond. Novel elongated mesh-tube packets containing anion-exchange resin (AER) beads were found to reduce drying and CO 2 loading time 4.3-fold compared to larger mesh bags. Technoeconomic analysis (TEA) estimates the cost of capturing CO 2 into an alkaline solution, suitable for cultivating photosynthetic microorganisms, to be $\$229$ per tonne for a practical scenario based on current results and $\$72$ per tonne for an aspirational scenario considering improvements to sorbent capacity, hydrophobicity, and sorbent lifetime. TEA further estimates an additional $\$110$ per tonne to extract CO 2 from solution, purify it, and compress it to 15 MPa, suitable for sequestration. Furthermore, moisture-driven processes have the potential to use up to 87% less energy than thermal and/or vacuum swing DAC by using energy from water evaporation.

09 BIOMASS FUELS↗
DOE OSTI2023

Probing High-Temperature Amine Chemistry: Is the Reaction NH 3 + NH 2 ⇌ N 2 H 3 + H 2 Important?

The reaction NH 3 + NH 2 ⇌ N 2 H 3 + H 2 (R1) has been identified as a key step to explain experimental results for pyrolysis and oxidation of ammonia. However, no direct experimental or theoretical evidence for the reaction has been reported. In the present work, the reaction was studied by ab initio theory and by reinterpretation of experimental data. We could not locate a transition state for R1 occurring as a direct process, but alternative mechanisms yielded an upper bound to k 1 of 1.5 × 10 13 exp(–58.9 kcal mol –1 /RT) cm 3 mol –1 s –1 over 1000–2500 K, several orders of magnitude lower than values applied in modeling. Consistent with the theoretical work, re-evaluation of NH 3 pyrolysis data supported a very low value of k 1 . However, this finding opens up a novel unresolved issue. Current kinetic models cannot capture the NH 3 oxidation behavior in a number of laminar flow reactor and jet-stirred reactor experiments without adopting an improbably high value for k 1 . Furthermore, important oxidation steps might be underestimated or missing from mechanisms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Gravity-driven controls on fluid and carbonate precipitation distributions in fractures

Abstract Many challenges related to carbon-dioxide ( $$\hbox {CO}_2$$ CO 2 ) sequestration in subsurface rock are linked to the injection of fluids through induced or existing fracture networks and how these fluids are altered through geochemical interactions. Here, we demonstrate that fluid mixing and carbonate mineral distributions in fractures are controlled by gravity-driven chemical dynamics. Using optical imaging and numerical simulations, we show that a density contrast between two miscible fluids causes the formation of a low-density fluid runlet that increases in areal extent as the fracture inclination decreases from 90 $$^\circ$$ ∘ (vertical fracture plane) to 30 $$^\circ$$ ∘ . The runlet is sustained over time and the stability of the runlet is controlled by the gravity-driven formation of 3D vortices that arise in a laminar flow regime. When homogeneous precipitation was induced, calcium carbonate covered the entire surface for horizontal fractures (0 $$^\circ$$ ∘ ). However, for fracture inclinations greater than 10 $$^\circ$$ ∘ , the runlet formation limited the areal extent of the precipitation to less than 15% of the fracture surface. These insights suggest that the ability to sequester $$\hbox {CO}_2$$ CO 2 through mineralization along fractures will depend on the fracture orientation relative to gravity, with horizontal fractures more likely to seal uniformly.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Limiting current in a collisional crossed-field gap

Crossed-field devices are often used in pulsed power and high-power microwave applications. Previous studies derived closed-form solutions for the limiting current of a vacuum crossed-field system, corresponding to the maximum permissible current for laminar flow, below and above the Hull cutoff B H for magnetic insulation. We extend these studies by introducing collision frequency into the electron force law as a friction term to derive the limiting current in a collisional crossed-field gap. The resulting solution recovers the vacuum crossed-field case in the limit of no collisions and the collisional space-charge limited current with general initial velocity for magnetic field B → 0. In the limit of infinite collisions, we obtain a crossed-field equivalent to the Mott–Gurney law for the maximum current permissible in a collisional, nonmagnetic diode. When the collision frequency ν is less than the electron cyclotron frequency Ω, increasing initial velocity makes the critical current nonmonotonic with increasing ν with the critical current higher at B = B H for ν = Ω. As for a misaligned crossed-field gap where a component of the magnetic field was introduced parallel to the electric field across the gap, magnetic insulation is eliminated and the discontinuity at B = B H for limiting current observed in a vacuum crossed-field gap vanishes. As B → ∞, the limiting current approaches a constant that depends on the initial velocity and the collision frequency.

Breen, Lorin I.↗
DOE OSTI2020

Field-emission plasma enhancement of H₂–O₂ micro-combustion

In this paper, a detailed three-dimensional computational model is developed to assess the potential of micron-scale field emission dielectric barrier discharge (FE-DBD) plasma actuators in non-premixed microburners with channel heights in the range of L z = 0.25–0.75 mm. Results for H 2 –O 2 combustion with Reynolds number Re = 100 are studied for different configurations of plasma actuator arrays. Without plasma actuation, results agree with corresponding experiments, although in this case the burner typically suffers from incomplete combustion due to thermal quenching, radical quenching, and slow diffusive mixing. For the range of conditions simulated, plasma actuation increases combustion completeness from 25%–70% to 40%–80% by enhancing mixing, generating radicals, and Joule heating. Ionic wind resulting from the FE-DBD plasma disrupts the otherwise simple laminar flow in the burner, accelerating the growth of a mixing layer and enhancing heat transfer to channel walls. The larger, lower temperature flames reduce thermal gradients (and thereby thermal stresses) in the walls. Radical generation due to electron-impact dissociation extends the reaction zone in the diffusion flame and increases combustion completeness. In all cases, the additional heat release with plasma actuation (100–190 W) is significantly larger than the power needed to sustain the plasma (≲0.1 W), suggesting that plasma actuation may provide a significant advantage in energy generation using realistic portable micro-combustion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Magnetohydrodynamics with physics informed neural operators

Abstract The modeling of multi-scale and multi-physics complex systems typically involves the use of scientific software that can optimally leverage extreme scale computing. Despite major developments in recent years, these simulations continue to be computationally intensive and time consuming. Here we explore the use of AI to accelerate the modeling of complex systems at a fraction of the computational cost of classical methods, and present the first application of physics informed neural operators (NOs) (PINOs) to model 2D incompressible magnetohydrodynamics (MHD) simulations. Our AI models incorporate tensor Fourier NOs as their backbone, which we implemented with the TensorLY package. Our results indicate that PINOs can accurately capture the physics of MHD simulations that describe laminar flows with Reynolds numbers Re ⩽ 250 . We also explore the applicability of our AI surrogates for turbulent flows, and discuss a variety of methodologies that may be incorporated in future work to create AI models that provide a computationally efficient and high fidelity description of MHD simulations for a broad range of Reynolds numbers. The scientific software developed in this project is released with this manuscript.

97 MATHEMATICS AND COMPUTING↗