Search NASA⌕ Search

SEARCH · Search NASA

Results for “Layer-by-Layer Fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

53 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Metallization of 3D Printed Parts for Electrode Fabrication

Additive manufacturing has the potential to fabricate electrodes with extremely small features with control of the electrode structure. However, most of the 3D printing capabilities produce structures made of polymers rather than electrodes which much be metal. This work aims to compare methods of metallization for parts created with additive manufacturing to allow them to be used as electrodes. We used three different methods of metallization: layer-by-layer gold nanoparticle coating, electroless copper deposition, and a combination of the two. We measured the resistance of the samples and observed the uniformity of the coating. We find that the standard electroless deposition procedure and using the layer-by-layer gold as a pretreatment yield similar resistances of less than 1 Ω. However, using gold as a pretreatment has possible cost benefits as compared to the standard electroless deposition procedure. Therefore, if many samples over a long period of time need to be metallized, we recommend using the layer-by-layer process combined with copper electroless deposition.

36 MATERIALS SCIENCE↗
DOE OSTI2024

AOI [1] Advanced Manufacturing of Ceramic Anchors with Embedded Sensors for Process and Health Monitoring of Coal Boilers

Researchers at West Virginia University (WVU) developed methods to fabricate and test ceramic anchors with an embedded sensor technology for monitoring the health and processing conditions within pulverized coal (PC) and fluidized-bed combustion (FBC) boiler systems. The technology included the development of advanced manufacturing processes for 2D/3D printing electroceramic (conductive ceramic) sensor designs within the ceramic anchor microstructure during the manufacturing process. This advanced manufacturing process would allow for the precise control of local microstructure and composition in order to engineer layer-by-layer any protective and electrically active materials within the refractory anchor. This 3D printing technology would permit the rapid and controlled design of the refractory microstructure and embedded sensor design throughout the volume of the ceramic anchor. The work also included a method to interconnect the sensors to boiler shell through the anchor clamp, where the sensor signals will be processed by low-power electronics and transmitted wirelessly to a central processing hub. The end-goal of the program was to produce a ceramic anchor sensor system which would be ready for implementation within a coal boiler, and/or other similar refractory liner systems (such as that in the glass and metal manufacturing areas). The project objectives were to: 1) Define the chemical and microstructural stability, in addition to the electrical properties, of oxide and non-oxide ceramic composites to be embedded within the ceramic anchor compositions that may operate up to 1400ºC; 2) Develop and implement the 2D/3D printing technology to pattern and control the microstructure of the ceramic anchor and embedded sensor circuits; 3) Develop an interconnect technology which will permit easy installation of the ceramic anchors and signal collection at the boiler shell; 4) Develop low power analog electronics and wireless communication hardware to efficiently collect the sensor signal at each processing unit and transmit data to a central hub for data analysis; 5) Demonstrate the smart ceramic anchor system for temperature and liner fracture within a high-temperature processing unit, such as a boiler furnace or glass melting furnace floor/wall liner.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

LLMs for Mfg.—On the State of Large Language Models and Applications to Manufacturing

Additive Manufacturing (AM), referred to as 3D printing, has emerged as a key pillar of Industry 4.0 enabling layer-by-layer fabrication of intricate geometries from CAD models. In parallel, Large Language Models (LLMs), deep learning models for natural language generation trained on vast text corpora, have demonstrated unprecedented capabilities in understanding and generating human-like text. The convergence of these trends opens new opportunities at the intersection of AM and AI/ML, where LLMs can assist engineers and researchers in design, manufacture planning, and knowledge discovery. Recent academic work has begun to explore LLM applications in AM and adjacent fields, such as material science, mechanical engineering, and design for additive manufacturing. This exploration ranges from intelligent process planning to domain-specific knowledge retrieval. This survey provides a comprehensive review of current developments, focusing on peer-reviewed literature contributions that apply, adapt, and advance LLMs in general and domain-specific domains. We analyze state-of-the-art (SOTA) techniques, such as fine-tuning foundational models for specific domains, retrieval-augmented generation (RAG) pipelines, knowledge graph integration, and delve into the architectures and evaluation methods employed. The goal of this survey is to inform researchers and practitioners of the current capabilities and limitations of LLMs in general and in domain-specific applications, and to outline how these models are being tailored to meet the requirements of these applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Residual Strains in an Additively Processed Ni-based Superalloy Transpiration-Cooled Aerodynamic Leading Edge Structure using Neutron Diffraction

Selective Laser Melting (SLM) is a well-known additive manufacturing method based on a layer-by-layer building process that is capable of fabricating gas turbine Ni-based superalloy parts with complex and integrated cooling geometries that are typically not achievable using conventional casting methods. However, the impact of residual stress concentration on SLM component life is a concern. In this work, residual strains present at room temperature in an SLM Inconel 718 generic aerodynamic leading edge segment with transpiration cooling were investigated using neutron diffraction at Oak Ridge National Laboratory. This study reveals that areas of the part where complex cooling holes were printed exhibit residual tensile strains that can be detrimental to its integrity. The study paves the way for future studies of the design of cooling hole geometries and manufacturing parameters that achieve improved cooling while minimizing stress concentration effects.

Fouliard, Quentin↗
DOE OSTI2020

Wire-Based Additive Manufacturing of Stainless Steel Components

In this work three different wire-fed additive manufacturing (AM) processes were employed to evaluate differences between laser, arc, and electron beam heat sources used for high-deposition-rate AM on the order of 1 kg/h. Optimum weld and build parameters were developed independently to match the characteristics of each heat source using 308L stainless steel welding wire as the feedstock. Laser-wire AM was made with the lowest energy per unit length of weld and had the best control of the melt pool and surface finish. Wire arc-based AM had an intermediate energy per unit length of weld of approximately 5× that of the laser process, while electron beam wire AM had the highest energy per unit length of weld at approximately 10× that of the laser process. Analysis of the parts that were built included evaluation of mechanical properties and microstructures, and these properties are discussed with respect to the difference in input energy and cooling rates. Results show that all three processes build parts with properties that exceed those of annealed 304L wrought stainless steel. However, significant differences exist between the processes, and the results presented here can be used to help select the best wire-fed process for a given high-deposition-rate application.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Altering the Supply of Shielding Gases to Fabricate Distinct Geometry in GMA Additive Manufacturing

Wire arc additive manufacturing (WAAM) is the process by which large, metallic structures are built, layer-by-layer, using a welding arc to melt wire feedstock. In this process, the proper selection of the shielding gas plays a vital role in the achievement of structurally acceptable part geometries and quality surface finishes. In this study, the authors used either a ternary mix (He, Ar and CO 2 ) or a binary mix (Ar and CO 2 ) of shielding gases to deposit wall geometries using an open loop-controlled WAAM system developed at Oak Ridge National Laboratory’s Manufacturing Demonstration Facility. The binary blend produced a wider and shorter geometry, while the ternary blend resulted in a narrower build that was more equivalent to the CAD geometry. The data indicated that the binary blend provided a higher oxygen concentration in the weld as compared to that of the ternary blend. The results imply that the arc characteristics and heat input had a significantly higher impact on the weld penetration than the surface tension effect of surface active elements. This was further verified by developing and applying a high-fidelity computational fluid dynamics (CFD) model of the thermophysical properties of gas mixtures. The results from the model showed that, while the influence of increased oxygen concentration on the surface tension for the binary blend led to a deeper penetration, the ternary blend gave rise to heat flux to the workpiece.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Optimization of La 2–x Sr x CuO 4 Single Crystal Film Growth via Molecular Beam Epitaxy

Atomic layer-by-layer molecular beam epitaxy (ALL-MBE) combined with ozone is one of the best methods to fabricate single-crystal thin films of complex oxides. Cuprate such as La 2-x Sr x CuO 4 (LSCO) is a representative complex-oxide high-temperature superconductor (HTS) material. Our group utilizes this method to produce high-quality single-crystal HTS films with atomically smooth surfaces and interfaces. In addition, ALL-MBE enables us to engineer multilayer heterostructures with atomic precision. This allows the fabrication of tunnel junctions, various nanostructures, and other HTS devices of interest for superconducting electronics. We have synthesized over three thousand LSCO thin films in the past two decades. These films’ structural and electronic properties have been studied and characterized by various methods. Here, we distill the extensive experience we accumulated into a step-by-step protocol to fabricate atomically perfect LSCO films. The recipe includes substrate preparation, ozone generation and distillation, source calibration, the in situ monitoring of the film synthesis, post-growth annealing, and ex situ characterization. It discloses a reproducible way to fabricate single-crystal LSCO films for basic research and HTS electronic applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

The Effect of Interlayer Delay on the Heat Accumulation, Microstructures, and Properties in Laser Hot Wire Directed Energy Deposition of Ti-6Al-4V Single-Wall

Laser hot wire directed energy deposition (LHW-DED) is a layer-by-layer additive manufacturing technique that permits the fabrication of large-scale Ti-6Al-4V (Ti64) components with a high deposition rate and has gained traction in the aerospace sector in recent years. However, one of the major challenges in LHW-DED Ti64 is heat accumulation, which affects the part quality, microstructure, and properties of as-built specimens. These issues require a comprehensive understanding of the layerwise heat-accumulation-driven process–structure–property relationship in as-deposited samples. In this study, a systematic investigation was performed by fabricating three Ti-6Al-4V single-wall specimens with distinct interlayer delays, i.e., 0, 120, and 300 s. The real-time acquisition of high-fidelity thermal data and high-resolution melt pool images were utilized to demonstrate a direct correlation between layerwise heat accumulation and melt pool dimensions. The results revealed that the maximum heat buildup temperature of the topmost layer decreased from 660 °C to 263 °C with an increase to a 300 s interlayer delay, allowing for better control of the melt pool dimensions, which then resulted in improved part accuracy. Furthermore, the investigation of the location-specific composition, microstructure, and mechanical properties demonstrated that heat buildup resulted in the coarsening of microstructures and, consequently, the reduction of micro-hardness with increasing height. Extending the delay by 120 s resulted in a 5% improvement in the mechanical properties, including an increase in the yield strength from 817 MPa to 859 MPa and the ultimate tensile strength from 914 MPa to 959 MPa. Cooling rates estimated at 900 °C using a one-dimensional thermal model based on a numerical method allowed us to establish the process–structure–property relationship for the wall specimens. The study provides deeper insight into the effect of heat buildup in LHW-DED and serves as a guide for tailoring the properties of as-deposited specimens by regulating interlayer delay.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Machine Learning for Additive Manufacturing of Functionally Graded Materials

Additive Manufacturing (AM) is a transformative manufacturing technology enabling direct fabrication of complex parts layer-by-layer from 3D modeling data. Among AM applications, the fabrication of Functionally Graded Materials (FGMs) has significant importance due to the potential to enhance component performance across several industries. FGMs are manufactured with a gradient composition transition between dissimilar materials, enabling the design of new materials with location-dependent mechanical and physical properties. This study presents a comprehensive review of published literature pertaining to the implementation of Machine Learning (ML) techniques in AM, with an emphasis on ML-based methods for optimizing FGMs fabrication processes. Through an extensive survey of the literature, this review article explores the role of ML in addressing the inherent challenges in FGMs fabrication and encompasses parameter optimization, defect detection, and real-time monitoring. The article also provides a discussion of future research directions and challenges in employing ML-based methods in the AM fabrication of FGMs.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

Neutron Imaging of Al6061 Prepared by Solid-State Friction Stir Additive Manufacturing

Solid-state Friction Stir Additive Manufacturing has recently gained attention as a result of its capacity to fabricate large-scale parts while preserving the mechanical properties of the feedstock material. However, the correlation between the quality of layer-by-layer bonding of the deposited metal and processing parameters has remained unknown. Neutron imaging techniques, with 90% total transmission per cm, are employed for Al6061 parts fabricated by MELD ® Technology as a non-destructive evaluation approach for the first time to investigate the layer-by-layer structure of a stadium-shaped ingot in different sections. The post-processed results show the fabricated parts with an optimized set of processing parameters are void-free. However, the hydrocarbon-based feedstock lubricant segregates between the layers, which consequently may lead to non-uniform weaker mechanical properties along the build direction and stimulate crack initiation during mechanical loading. The tensile test results show 14% lower strain-to-failure values in alleged contaminated areas in transmission imaging results. Additionally, layer bonding is significantly impacted by hot-on-hot and hot-on-cold layer deposition schemes, especially for larger layer thicknesses.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Advancing Industry 4.0: Multimodal Sensor Fusion for AI-Based Fault Detection in 3D Printing

Additive manufacturing, particularly fused deposition modeling, is transforming modern production by enabling rapid prototyping and complex part fabrication. However, its layer-by-layer process remains vulnerable to faults such as nozzle clogging, filament runout, and layer misalignment, which compromise print quality and reliability. Traditional inspection methods are costly, time-intensive, and often limited to post-process analysis, making them unsuitable for real-time intervention. In this current study, the authors developed a novel, low-cost, and portable faultdetection system that leverages multimodal sensor fusion and artificial intelligence for real-time monitoring in FDM-based 3D printing. The system integrates acoustic, vibration, and thermal sensing into a non-intrusive architecture, capturing complementary data streams that reflect both mechanical and process-related anomalies. Acoustic and thermal sensors operate in a fully contactless manner, while the vibration sensor requires minimal attachment such that it will not interfere with printer hardware, thereby preserving portability and ease of deployment. The multimodal signals are processed into spectrograms and time-frequency features, which are classified using convolutional neural networks for intelligent fault detection. The proposed system advances Industry 4.0 objectives by offering an affordable, scalable, and practical monitoring solution that improves faultdetection accuracy, reduces waste, and supports sustainable, adaptive manufacturing.

42 ENGINEERING↗
DOE OSTI2021

Metal fluoride passivation coatings prepared by atomic layer deposition for Li-ion batteries

The fabrication of robust interfaces between transition metal oxides and non-aqueous electrolytes is one of the great challenges of lithium ion batteries. Atomic layer deposition (ALD) of aluminum tungsten fluoride (AlWxFy) improves the electrochemical stability of LiCoO2. AlWxFy thin films were deposited by combining trimethylaluminum and tungsten hexafluoride. in-situ quartz crystal microbalance and transmission electron microscopy studies show that the films grow in a layer-by-layer fashion and are amorphous nature. Ultrathin AlWxFy coatings (<10 Å) on LiCoO2 significantly enhance stability relative to bare LiCoO2 when cycled to 4.4 V. The coated LiCoO2 exhibited superior rate capability (up to 400 mA/g) and discharge capacities at a current of 400 mA/g were 51% and 92% of the first cycle capacities for the bare and AlWxFy coated materials. These results open new possibilities for designing ultrathin and electrochemically robust coatings of metal fluorides via ALD to enhance the stability of Li-ion electrodes.

Mane, Anil U.↗
DOE OSTI2022

Design and Use of a Penetrating Deposition Nozzle for Z-Pinning Additive Manufacturing

Fused Filament Fabrication (FFF) involves depositing material layer-by-layer to create athree-dimensional object. This method often demonstrates high mechanical anisotropy in theprinted structure, leading to a drop in the material strength of the part when comparing structuresalong the deposition plane (X/Y-Axis) versus across layers in the build direction (Z-Axis). Initialefforts to improve anisotropy led to the development of the Z-Pinning process, where continuouspins are deposited across layers in the Z-Axis. Z-pinning has demonstrated significant gains intoughness and inter-layer strength, particularly in fiber-reinforced materials. However, thisprocess can also create flaws in the structure that increase in severity and frequency as the pinsgrow in length and diameter. To mitigate this, a penetrating nozzle has been developed thatextends a fine-tipped extrusion nozzle deep into the pin cavity and simultaneously extrudesmaterial as it retracts. This study investigates the printability of the penetrating nozzle for simplegeometries and evaluates the resulting Z-pinning mesostructure. As a result of this study, theprototype penetrating nozzle design was analyzed and built. Through a pressure driven flowanalysis it was determined that the penetrating nozzle extruder can not only flow extrudefilament. After a transient thermal simulation it was found that after a pause of 15 secondsresume printing with no drop in heat at nozzle exit.

Bales, Brenin↗
DOE OSTI2022

Emulsion stereolithography and 3D printing of multimaterials and nanoscale material gradients

A functionally graded material is formed by pipetting individual micro-or-nano-litter droplets with a variety of materials including multi-nanostructured material (nanowires, carbon nanotubes, enzymes, multi-element and/or multi-color, multi-biomolecules) and UV polymerization of the flat hydrogel meniscus surface formed at the carrier fluid interface. After step-by-step droplet pipetting and subsequent layer-by-layer UV polymerization via a digital mask, the complete fabricated part without supporting layers is taken out of the carrier fluid while the un-cured micro-litter residue is conveniently suctioned out of the carrier fluid.

Zheng, Xiaoyu↗
DOE OSTI2022

System and method for high power diode based additive manufacturing

The present disclosure relates to a system for performing an Additive Manufacturing (AM) fabrication process on a powdered material (PM) forming a substrate. The system uses a first optical subsystem to generate an optical signal comprised of electromagnetic (EM) radiation sufficient to melt or sinter a PM of the substrate. The first optical subsystem is controlled to generate a plurality of different power density levels, with a specific one being selected based on a specific PM forming a powder bed being used to form a 3D part. At least one processor controls the first optical subsystem and adjusts a power density level of the optical signal, taking into account a composition of the PM. A second optical subsystem receives the optical signal from the first optical subsystem and controls the optical signal to help facilitate melting of the PM in a layer-by-layer sequence of operations.

El-Dasher, Bassem S.↗
DOE OSTI2024

Metal fluoride passivation coatings prepared by atomic layer deposition for Li-ion batteries

The fabrication of robust interfaces between transition metal oxides and non-aqueous electrolytes is one of the great challenges of lithium ion batteries. Atomic layer deposition (ALD) of aluminum tungsten fluoride (AlWxFy) improves the electrochemical stability of LiCoO 2 . AlWxFy thin films were deposited by combining trimethylaluminum and tungsten hexafluoride. in-situ quartz crystal microbalance and transmission electron microscopy studies show that the films grow in a layer-by-layer fashion and are amorphous nature. Ultrathin AlWxFy coatings (<10 Å) on LiCoO 2 significantly enhance stability relative to bare LiCoO 2 when cycled to 4.4 V. The coated LiCoO 2 exhibited superior rate capability (up to 400 mA/g) and discharge capacities at a current of 400 mA/g were 51% and 92% of the first cycle capacities for the bare and AlWxFy coated materials. These results open new possibilities for designing ultrathin and electrochemically robust coatings of metal fluorides via ALD to enhance the stability of Li-ion electrodes.

Mane, Anil U.↗
DOE OSTI2024

System and method for high power diode based additive manufacturing

The present disclosure relates to a system for performing an Additive Manufacturing (AM) fabrication process on a powdered material, deposited as a powder bed and forming a substrate. The system makes use of a laser for generating a laser beam, and an optical subsystem. The optical subsystem is configured to receive the laser beam and to generate an optical signal comprised of electromagnetic radiation sufficient to melt or sinter the powdered material. The optical subsystem uses a digitally controlled mask configured to pattern the optical signal as needed to melt select portions of a layer of the powdered material to form a layer of a 3D part. A power supply and at least one processor are also included for generating a plurality of different power density levels selectable based on a specific material composition, absorptivity and diameter of the powder particles, and a known thickness of the powder bed. The powdered material is used to form the 3D part in a sequential layer-by-layer process.

El-Dasher, Bassem S.↗