Search NASA⌕ Search

SEARCH · Search NASA

Results for “Low Impact”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Investigation of low velocity impact damage on filamentary composite materials

Presented are the results of an investigation of the effect of low velocity impact on the residual modulus and residual strength of flat filamentary composite materials. Theoretical analysis of composite materials indicates that the modulus of the material must decrease as impact damage increases. This decrease must also correlate to the decrease in residual strength. This study attempts to verify these hypotheses. Graphite/epoxy laminates (AS4/3501-6) of various fiber orientations (8 (0 deg), 2 (+ or - 45 deg)sub 8) were impacted using a falling weight impact tester. Impact energies ranged from 0.42 to 1.55 ft-lb, with impact velocities from 2.03 to 3.98 ft/sec. The results show that there is a reduction in residual modulus of the plate as the impact energy increases.

Bower, Mark V.↗
NASA NTRS1992

Effect of low-speed impact damage and damage location on behavior of composite panels

An investigation of the effects of low-speed impact damage on the compression and tension strength of thin (less than .05 inches thick) and moderately thick (between .12 and .17 inches thick) composite specimens was conducted. Impact speeds ranged from 50 to 550 ft/sec (impact energies from .25 to 30.7 ft-lb) and impact locations were near or away from a lateral unloaded edge. In this study, thin tension-loaded or compression-loaded specimens with only 90 deg and +/- 40 deg plies which were impacted away from the unloaded edge suffered less reduction in maximum load-carrying capability due to impact damage than the same specimens impacted near the unloaded edge. Unlike the thin laminates, failure loads of thicker compression-loaded specimens with a similar stacking sequence were independent of impact location. Failure loads of thin tension-loaded specimens with 0 deg plies were independent of impact location while failure loads of thicker compression-loaded specimens with 0 deg plies were dependent upon impact location. A finite-element analysis of strain distributions across the panel width indicated that high axial strains occur near the unloaded edges of postbuckled panels, indicating that impacts near the unloaded edge would significantly effect the behavior of postbuckled panels.

Jegley, Dawn↗
NASA NTRS1981

Development of an engineering analysis of progressive damage in composites during low velocity impact

A computerized, analytical methodology was developed to study damage accumulation during low velocity lateral impact of layered composite plates. The impact event was modeled as perfectly plastic with complete momentum transfer to the plate structure. A transient dynamic finite element approach was selected to predict the displacement time response of the plate structure. Composite ply and interlaminar stresses were computed at selected time intervals and subsequently evaluated to predict layer and interlaminar damage. The effects of damage on elemental stiffness were then incorporated back into the analysis for subsequent time steps. Damage predicted included fiber failure, matrix ply failure and interlaminar delamination.

Humphreys, E. A.↗
NASA NTRS1983

Residual strength assessment of low velocity impact damage of graphite-epoxy laminates

This report contains the study of Low Velocity Transverse Impact Damage of graphite-epoxy T300/5208 composite laminates. The specimen, 100 mm diameter clamped plates, were impact damaged by a cantilever-type instrumented 1-inch diameter steel ball. Study was limited to impact velocity 6 m/sec. Rectangular strips, 50 mm x 125 mm, were cut from the impact-damage specimens so that the impact damage zone was in the center of the strips. These strips were tested in tension to obtain their residual strength. An energy dissipation model was developed to predict the residual strength from fracture mechanics concepts. Net energy absorbed I(a) was evaluated from coefficient of restitution concepts based on shear dominated theory of fiber-reinforced materials, with the modification that during loading and unloading the shear deformation are respectively elastic-plastic and elastic. Delamination energy I(d) was predicted by assuming that the stiffness of the laminate dropped due to debonding. Fiber-breakage energy, assumed to be equal to the difference of I(a) and I(d), was used to determine the residual strength. Predictions were compared with test results.

Lal, K. M.↗
NASA NTRS1983

Effect of specimen size on the buckling behavior of laminated composites subjected to low-velocity impact

An experimental investigation was conducted to study the effect of specimen size on the buckling strains of composite laminates subjected to low-velocity projectile impact. The specimens were fabricated from a T300/5208 graphite/epoxy material with laminate configurations (+ or - 45,0,90)2s and (+ or - 45,0,90)4s. These 16- and 32-ply quasi-isotropic laminates were side-supported during testing. Specimens of three different length-to-width aspect ratios of 1, 1.5, and 2 were studied. The low-velocity projectile impact was provided by an air gun. The preload and impact energy combination necessary to cause catastrophic buckling failure was determined. The residual strength of specimens that survived the impact damage was also measured. The results were compared with those of a 48-ply laminate tested elsewhere. The present experimental results show that (1) specimen length does not seem to have any significant influence on the buckling strains at failure caused by projectile impact and (2) the influence of specimen thickness on strain at failure decreases as the velocity of the projectile increases.

Avva, V. S.↗
NASA NTRS1979

Low-velocity impact craters in ice and ice-saturated sand with implications for Martian crater count ages

The paper reports on a series of low-velocity impact experiments performed in ice and ice-saturated sand. It is found that crater diameters in ice-saturated sand were about 2 times larger than in the same energy and velocity range in competent blocks of granite, basalt and cement, while craters in ice were 3 times larger. It is shown that if this dependence of crater size on strength persists to large hypervelocity impact craters, then surface of geologic units composed of ice or ice-saturated soil would have greater crater count ages than rocky surfaces with identical influx histories. Among the conclusions are that Martian impact crater energy versus diameter scaling may also be a function of latitude.

Croft, S. K.↗
NASA NTRS2010

NASA Docking System (NDS) Interface Definitions Document (IDD)

The NASA Docking System (NDS) mating system supports low approach velocity docking and provides a modular and reconfigurable standard interface, supporting crewed and autonomous vehicles during mating and assembly operations. The NDS is NASA's implementation for the emerging International Docking System Standard (IDSS) using low impact docking technology. All NDS configurations can mate with the configuration specified in the IDSS Interface Definition Document (IDD) released September 21, 2010. The NDS evolved from the Low Impact Docking System (LIDS). The acronym international Low Impact Docking System (iLIDS) is also used to describe this system. NDS and iLIDS may be used interchangeability. Some of the heritage documentation and implementations (e.g., software command names) used on NDS will continue to use the LIDS acronym. The NDS IDD defines the interface characteristics and performance capability of the NDS, including uses ranging from crewed to autonomous space vehicles and from low earth orbit to deep space exploration. The responsibility for developing space vehicles and for making them technically and operationally compatible with the NDS rests with the vehicle providers. Host vehicle examples include crewed/uncrewed spacecraft, space station modules, elements, etc. Within this document, any docking space vehicle will be referred to as the host vehicle. This document defines the NDS-to-NDS interfaces, as well as the NDS-to-host vehicle interfaces and performance capability.

Source record↗
NASA NTRSDate not supplied

Low-Velocity Impact Analyses of Composite Panels Using Cohesive Zone Modeling and Continuum Damage Mechanics

A parametric study was conducted to gage the sensitivity of simulations of low-velocity impacts on laminated composite panels to various finite element model and material model features. The material model used in this parametric study was previously verified and validated for conducting progressive damage analyses of post-buckled composite structures subjected to quasi-static loading conditions. Based on the results of this parametric study, updates have been made to a progressive damage analysis material model and the best practices for its application. Experimental results are compared to computational results obtained with and without the updates to the models. Both thermoset and thermoplastic fiber-reinforced materials are considered. The resulting enhancements to the material model are presented in detail.

Frank A Leone↗
NASA NTRSDate not supplied

Low-Velocity Impact Analyses of Composite Panels Using Cohesive Zone Modeling and Continuum Damage Mechanics

A parametric study was conducted to gage the sensitivity of simulations of low-velocity impacts on laminated composite panels to various finite element model and material model features. The material model used in this parametric study was previously verified and validated for conducting progressive damage analyses of post-buckled composite structures subjected to quasi-static loading conditions. Based on the results of this parametric study, updates have been made to a progressive damage analysis material model and the best practices for its application. Experimental results are compared to computational results obtained with and without the updates to the models. Both thermoset and thermoplastic fiber-reinforced materials are considered. The resulting enhancements to the material model are presented in detail.

Frank Leone↗
NASA NTRS1985

Large deflection behavior of quasi-isotropic laminates under low-velocity impact type point loading

Eight-ply quasi-isotropic circular composite plates of Thornel 300 graphite in Narmco 5208 epoxy resin (T300/5208) were analyzed to obtain the large deformation behavior under low-velocity impact type point loads. A simple plate-membrane coupling model was developed. The impact type point loads were replaced by equivalent quasi-static point loads. The plate-membrane coupling model was used to obtain the large deformation shapes for the thin circular composite laminates. The analyses indicated that the large deformation shapes of the composite plates under point loads vary with the center point displacements, and hence are different for different load levels. Quasi-isotropic plates were analyzed by replacing anisotropic bending stiffness components with the equivalent flexural stiffness for the isotropic plates. The plate-membrane coupling model was verified by conducting a series of tests on clamped circular quasi-isotropic laminates. Deflected shapes for the thin composite plates were experimentally obtained. These shapes agreed well with the analytically predicted shapes.

Kelkar, A.↗
NASA NTRS2011

NASA Docking System (NDS) Interface Definitions Document (IDD)

The NASA Docking System (NDS) mating system supports low approach velocity docking and provides a modular and reconfigurable standard interface, supporting crewed and autonomous vehicles during mating and assembly operations. The NDS is NASA s implementation for the International Docking System Standard (IDSS) using low impact docking technology. All NDS configurations can mate with the configuration specified in the IDSS Interface Definition Document (IDD), Revision A, released May 13, 2011. The NDS evolved from the Low Impact Docking System (LIDS). The term (and its associated acronym), international Low Impact Docking System (iLIDS) is also used to describe this system. NDS and iLIDS may be used interchangeability. Some of the heritage documentation and implementations (e.g., software command names) used on the NDS will continue to use the LIDS acronym.

Lewis, James↗
NASA NTRS1992

Acoustic emission monitoring of low velocity impact damage in graphite/epoxy laminates during tensile loading

An acoustic emission (AE) system was set up in a linear location data acquisition mode to monitor the tensile loading of eight-ply quasi-isotropic graphite/epoxy specimens containing low velocity impact damage. The impact damage was induced using an instrumented drop weight tower. During impact, specimens were supported by either an aluminum plate or a membrane configuration. Cross-sectional examinations revealed that the aluminum plate configuration resulted in primarily matrix cracking and back surface fiber failure. The membrane support resulted in only matrix cracking and delamination damage. Penetrant enhanced radiography and immersion ultrasonics were used in order to assess the amount of impact damage in each tensile specimen. During tensile loading, AE reliably detected and located the damage sites which included fiber failure. All specimens with areas of fiber breakage ultimately failed at the impact site. AE did not reliably locate damage which consisted of only delaminations and matrix cracking. Specimens with this type of damage did not ultimately fail at the impact site. In summary, AE demonstrated the ability to increase the reliability of structural proof tests; however, the successful use of this technique requires extensive baseline testing.

Parker, Bradford H.↗
NASA NTRS2023

Progressive Damage and Failure Analysis of Thermoplastic Composites in Low Velocity Impact Using MAT299

As part of the NASA Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project, state-of-the-art progressive damage and failure analysis (PDFA) tools developed for use with thermosets are being evaluated for use in modeling alternative material systems, like thermoplastics. Experimental low-velocity impact data of a thermoplastic material system, AS4D/PEKK-FC, is presented and includes characterization of the impact damage mechanisms as well as associated load and displacement data. Following the presentation of experimental results, two simulation approaches using the PDFA tool MAT299 in the commercial off-the-shelf finite element software LS-DYNA are employed to predict damage area and force-displacement responses of thermoplastic panels subjected to various impact energies. The first modeling method uses solid elements with a high-density mesh and a ply-by-ply modeling approach similar to previously published work for thermosets. This method has the capability of capturing individual crack development, progression, and delamination on a per ply basis. The second modeling method uses TSHELL elements that have in-plane dimensions that are an order of magnitude larger than the elements used in the solid element approach and reduces the number of elements through the thickness of the laminate. The second method produces a lower-fidelity model with reduced run times that is incapable of monitoring every delamination plane and damage within each ply. Results from both simulation methods are compared to experiment, and limitations of the methods are discussed.

Composite material↗
NASA NTRS2023

Progressive Damage and Failure Analysis of Thermoplastic Composites in Low Velocity Impact Using MAT299

As part of the NASA Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project, state-of-the-art progressive damage and failure analysis (PDFA) tools developed for use with thermosets are being evaluated for use in modeling alternative material systems, like thermoplastics. Experimental low-velocity impact data of a thermoplastic material system, AS4D/PEKK-FC, is presented and includes characterization of the impact damage mechanisms as well as associated load and displacement data. Following the presentation of experimental results, two simulation approaches using the PDFA tool MAT299 in the commercial off-the-shelf finite element software LS-DYNA are employed to predict damage area and force-displacement responses of thermoplastic panels subjected to various impact energies. The first modeling method uses solid elements with a high-density mesh and a ply-by-ply modeling approach similar to previously published work for thermosets. This method has the capability of capturing individual crack development, progression, and delamination on a per ply basis. The second modeling method uses TSHELL elements that have in-plane dimensions that are an order of magnitude larger than the elements used in the solid element approach and reduces the number of elements through the thickness of the laminate. The second method produces a lower-fidelity model with reduced run times that is incapable of monitoring every delamination plane and damage within each ply. Results from both simulation methods are compared to experiment, and limitations of the methods are discussed.

Composite material↗
NASA NTRS1972

Impact of low cost refurbishable and standard spacecraft upon future NASA space programs. Payload effects follow-on study, appendix

Mission analysis is discussed, including the consolidation and expansion of mission equipment and experiment characteristics, and determination of simplified shuttle flight schedule. Parametric analysis of standard space hardware and preliminary shuttle/payload constraints analysis are evaluated, along with the cost impact of low cost standard hardware.

Source record↗
NASA NTRSDate not supplied

Critical Progressive Damage Analysis Model Features for Low-Velocity Impact on Thermoset and Thermoplastic Panels

A previous verification and validation framework evaluated the ability of various progressive damage analysis (PDA) tools to predict the mechanical response and damage state in post-buckled stiffened aerospace structures composed of fiber-reinforced thermoset composite materials. Herein, the ability of PDA tools to predict damage in thermoplastic composite materials subject to low-velocity impact (LVI) loading has been assessed. LVI tests and analyses have been conducted for similar panels, comprising thermoset or thermoplastic composite materials. Preliminary test/analysis correlations revealed that using the same combination of PDA model features and finite element model-building guidelines for the thermoset and thermoplastic LVI specimens resulted in underprediction of matrix crack lengths and delaminated area in the thermoplastic analyses despite yielding good correlations for the thermoset specimens. In this paper, the quality of the test/analysis correlations for analyses of thermoplastic LVI specimens performed with different combinations of PDA model features using the NASA CompDam material model are presented. Model features that were assessed in terms of effect on the quality of the test/analysis correlation include the representation of damageable interfaces, residual thermal stresses, and fiber damage.

Frank Leone↗
NASA NTRSDate not supplied

Critical Progressive Damage Analysis Model Features for Low-Velocity Impact on Thermoset and Thermoplastic Panels

A previous verification and validation framework evaluated the ability of various progressive damage analysis (PDA) tools to predict the mechanical response and damage state in post-buckled stiffened aerospace structures composed of fiber-reinforced thermoset composite materials. Herein, the ability of PDA tools to predict damage in thermoplastic composite materials subject to low-velocity impact (LVI) loading has been assessed. LVI tests and analyses have been conducted for similar panels, comprising thermoset or thermoplastic composite materials. Preliminary test/analysis correlations revealed that using the same combination of PDA model features and finite element model-building guidelines for the thermoset and thermoplastic LVI specimens resulted in underprediction of matrix crack lengths and delaminated area in the thermoplastic analyses despite yielding good correlations for the thermoset specimens. In this paper, the quality of the test/analysis correlations for analyses of thermoplastic LVI specimens performed with different combinations of PDA model features using the NASA CompDam material model are presented. Model features that were assessed in terms of effect on the quality of the test/analysis correlation include the representation of damageable interfaces, residual thermal stresses, and fiber damage.

Frank Leone↗
NASA NTRS1979

Low-velocity impact damage in graphite-fiber reinforced epoxy laminates

An experimental investigation was conducted to identify the failure mechanisms and to understand damage propagation in compression-loaded composite structures. The tests were conducted on several laminates of different ply orientation with thickness that ranged from 0.56 to 0.75 cm. The panels were damaged by 1.27-cm-diameter aluminum spheres propelled normal to the specimen surface at velocities ranging from 30 m/s to 140 m/s. Results indicate that there is significant internal laminate damage due to low-velocity impact with no surface damage. The internal damage consists of delamination and intraply cracking. Three damage propagation modes were identified as causing specimen failure; which are delamination, axial load-lateral deformation coupling, and local shear failure.

Rhodes, M. D.↗