Search NASA⌕ Search

SEARCH · Search NASA

Results for “MATERIALS SELECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Nonlinear viscoelastic response of silicone additively manufactured direct ink write (DIW) foams under repetitive compression

To investigate dynamic fatigue behavior of foam in military protective applications, such as helmets, additively manufactured (AM) foams were compressively strained into the plateau region using a reduced design of experiments. A simple power law was found to govern the decline in dynamic stiffness (complex modulus) as the foams underwent the purchase order requirement of 10,000 cycles of small deformation in the plateau region. This rate of decline was newly found to correlate with the degree of nonlinearity in the material’s deformation, quantified using total harmonic distortion. Materials with low nonlinearity exhibited relatively stable stiffness across cycles, while those with high nonlinearity experienced greater losses. The observed nonlinearity depended on both applied stress and strain rate. A strong linear correlation (R 2 = 0.78) was identified between second-order nonlinearity and the time-dependent stiffness response. Two lattice structures were examined: face-centered tetragonal (FCT) and simple cubic (SC). The SC material exhibited higher total harmonic distortion (5%) and lower stiffness retention than the FCT (2%). In conclusion, these results suggest that for cyclic compression applications in a wide variety of industries such as packaging, personal protective equipment, or aerospace, selecting materials with lower stress and greater structural uniformity can enhance the stability of dynamic performance.

42 ENGINEERING↗
DOE OSTI2025

Updating the Building Science Advisor (BSA): A Tool to Assist in the Design of Durable Building Envelopes

Predicting the moisture durability of building envelope components remains challenging due to multiple influencing factors, including material selection, assembly positioning, local climate conditions, air tightness, interior environment, and construction quality. Building codes increasingly emphasize energy efficiency through enhanced insulation and tighter envelopes but offer limited guidance on moisture durability considerations. Consequently, builders face uncertainty, particularly as new materials and assemblies enter the market.The Building Science Advisor (BSA) is a free, web-based expert system developed to address these challenges by providing actionable insights into the moisture durability and energy efficiency of both new and retrofit wall designs. Recently updated, we are now providing version 3.0 of the tool. BSA features significant user interface improvements, enhancing navigation and user interaction through a refreshed, intuitive design. Additionally, the tool incorporates a newly developed database containing pre-simulated wall assembly cases, significantly reducing response times and improving the accuracy of moisture durability assessments. Furthermore, the updated BSA includes moisture content as a performance criterion, providing users with a more comprehensive understanding of moisture-related durability risks. These enhancements enable rapid, reliable assessments tailored to specific climate zones and local building practices. BSA continues to offer targeted guidance on wall retrofit scenarios and delivers access to an expanded library of location-specific building science resources.This paper describes these key updates, highlighting the enhanced features, expanded capabilities, and overall improvements to user experience and educational content. The paper includes a demonstration that illustrates how the revised BSA effectively supports practitioners in designing durable, energy-efficient building envelope assemblies.

Salonvaara, Mikael [ORNL] (ORCID:0000000318991554)↗
DOE OSTI2024

High temperature electrical property measurements of ceramics

Emerging applications in energy and aerospace systems require high quality data on the high temperature electrical properties of ceramics, particularly oxides, to guide material selection, design, and modeling. This presentation demonstrates the functionality of a specially designed sample fixture that enables electrical measurements to be conducted up to temperatures as high as 1600°C. Utilizing the mismatch in the coefficient of thermal expansion between two materials, a purely mechanical method for establishing electrical contact in the van der Pauw geometry is used to measure the bulk resistivity of ceramic materials. Measurements conducted on a number of common high temperature materials will be presented, including 20 mol % Gd-doped cerium oxide. Measurements are performed using multiple techniques and compared to literature values finding excellent agreement. The approach described in this work enables the van der Pauw method to be applied to many ceramic materials over a wide range of temperatures and environments.

Cann, David P.↗
DOE OSTI2024

Permeation of niobium through grain boundaries in copper

Low mutual solubility is expected to avert interdiffusion in layered composites of phase-separating metals. However, we show that Nb diffuses through polycrystalline Cu—despite the minimal bulk solubility of these elements—due to short circuit transport of Nb along certain grain boundaries in Cu. Atomistic modeling demonstrates that Nb-permeable Cu grain boundaries exhibit negative enthalpy of mixing of Nb, resulting in an enthalpically-stabilized solution of highly mobile Nb atoms that easily diffuse through the boundary. By contrast, Mo, which also has minimal solubility with Cu, has positive enthalpy of mixing at Nb-permeable Cu grain boundaries and does not diffuse through them. Furthermore, our findings suggest material selection and grain boundary engineering as pathways for designing improved diffusion barriers and thermally stable laminate composites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Permeation of niobium through grain boundaries in copper

Low mutual solubility is expected to avert interdiffusion in layered composites of phase-separating metals. However, we show that Nb diffuses through polycrystalline Cu—despite the minimal bulk solubility of these elements—due to short circuit transport of Nb along certain grain boundaries in Cu. Atomistic modeling demonstrates that Nb-permeable Cu grain boundaries exhibit negative enthalpy of mixing of Nb, resulting in an enthalpically-stabilized solution of highly mobile Nb atoms that easily diffuse through the boundary. By contrast, Mo, which also has minimal solubility with Cu, has positive enthalpy of mixing at Nb-permeable Cu grain boundaries and does not diffuse through them. Furthermore, our findings suggest material selection and grain boundary engineering as pathways for designing improved diffusion barriers and thermally stable laminate composites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A mechanistic interpretation of Nelson curves for PVP failures under high temperature hydrogen attack

As an empirically established design criterion, Nelson curves that relate the service temperature and the allowable hydrogen partial pressure have been developed and utilized for more than sixty years in pressure vessels and piping (PVP) safety design. Despite a relatively clear thermodynamic understanding of the high-temperature-hydrogen-attack (HTHA) problem, the detailed fracture process on the microstructural length scales, however, remains elusive, and a quantitative assessment of the PVP lifetime under HTHA from the available creep fracture dataset is still not possible. This work develops a microstructure-informed and micromechanics-based model by incorporating a synergy between hydrogen transport and intergranular-cavity-based fracture process. Based on the available creep lifetime data of C-0.5Mo steels, we are able to calibrate material constitutive parameters, and then conduct nonlinear finite element simulations that reveal a real-time stress-induced hydrogen diffusional transport along grain boundaries, coupled with a microstructure-explicit failure process, from which Nelson curves can be computed. Such failure analyses allow us to delineate two distinct regimes on the Nelson curves, i.e., dislocation-creep-controlled or grain boundary diffusion-assisted cavity growth. More importantly, we found that a small change of the pipe thickness and applied stresses can significantly shift these lifetime curves. However, these two parameters are usually not provided in Nelson curves, thus limiting their usage in material selection and safety design. In conclusion, this discrepancy can clearly be mitigated by extensive parametric studies from our micromechanical modeling/simulation framework.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Novel Hot Gas Components for Gas Turbine Engines Enabled by Materials and Additive Manufacturing Process Development

Additive Manufacturing (AM), also known as 3D printing, has emerged as a manufacturing method that enables new design freedom for gas turbine engine manufacturers. However, the material selection for AM processable high-temperature super alloys is currently limited. Additionally, the heat transfer performance of AM enabled micro-cooling architectures is not yet well understood. Accordingly, in support of advanced manufacturing and engine performance development, Oak Ridge National Laboratory (ORNL)and Solar Turbines (Solar) conducted a multidisciplinary project to generate both AM super alloy material properties data and micro-channel performance data for two AM super alloys. The data supported the design and analysis of an internally cooled turbine hot section AM tip shoe component. This data was used to analytically predict the reduction in operating temperature of a gas turbine tip shoe. The work concluded that the cooling flow required to cool the tip shoe can be tuned to suit the efficiency improvements desired in an industrial gas turbine.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermocouple and RTD Drift Due to Neutron Irradiation and Temperature for Space Nuclear Applications: A Review

Temperature measurement is a key factor in the safe and reliable operation of nuclear reactors. Thermocouples and resistance temperature detectors (RTDs) are among the most common and reliable tools deployed for temperature measurement, and some are capable of operating in extreme environments such as very high temperature and neutron radiation fields anticipated in nuclear thermal propulsion (NTP) or fission surface power. These devices are known to exhibit drifting behavior in their temperature readings throughout their operational lifetimes. Here, to help select appropriate instrumentation, it is important to identify the factors that influence drift as well as typical behavior in these environments. This work is focused on identifying contributing factors in the performance of thermocouples and RTDs. An extensive literature review is included that discusses several experimental results in different environments. Although individual instrument performance may vary with construction methods, materials selection, and vendors, this review aims to assist in the selection process and identify typical expected behaviors of several devices.

Chesser, Ryan J. [Oak Ridge National Laboratory (O↗
DOE OSTI2025

Investigating Fast Scanning Calorimetry and Differential Scanning Calorimetry as Screening Tools for Thermoset Polymer Material Compatibility with Laser-Based Powder Bed Fusion

As additive manufacturing (AM) technology has developed and progressed, a constant topic of research in the area is expanding the library of materials to be used with these techniques. Among AM methods that utilize polymers, laser-based powder bed fusion (PBF-LB) has preferentially used thermoplastic polymers as its starting materials, but the deposition and material joining method employed in PBF-LB may also be compatible with powdered thermoset polymer precursors as feedstocks. To assess the compatibility of candidate thermosetting polymers and PBF-LB, characterization techniques and protocols that link fundamental material behavior to material behavior in the processing environment are needed. Therefore, the objectives of this work are to compare the curing behavior measured with two different calorimetry techniques that can operate in different heating rate regimes, differential scanning calorimetry (DSC) and fast scanning calorimetry (FSC), and to assess the capabilities of these techniques to act as materials screening tools for PBF-LB. A commercial polyester powder coating is used as a model material to evaluate the potential of obtaining complimentary information for material screening through a combination of calorimetry methods, and its non-isothermal curing behavior is measured at heating rates between 5 °C/min and 7500 °C/min. Curing exotherms are observed with both calorimetry techniques, and comparing the enthalpy associated with curing shows that incomplete curing occurs at higher heating rates, with relative conversion values of approximately 30%. The curing data are fit with two isoconversional models, Friedman and Starink, which show a reduced activation energy at higher heating rates as well, signifying a lower barrier to curing at the conditions used in the FSC experiments. Overall, the results of this work indicate that using these two calorimetry techniques as tiered screening tools can provide valuable information about how curing may proceed in PBF-LB and inform materials selection and design activities for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Final Report on Characterization of Irradiated Sensors and Coupling Adhesive Bonds

This report summarizes characterization via scanning/transmission electron microscopy of the microstructures of the unirradiated and irradiated piezoelectric ultrasonic sensor/aluminum substrate assemblies using four commercially available inorganic coupling adhesives to bond two types of piezoelectric crystals to the substrates. The sample assemblies were irradiated in the PULSTAR reactor at NC State University and ultrasonic data was collected in-situ. ORNL LAMDA Laboratory capabilities were utilized to perform pre- and post-irradiation examination of the sensor assemblies. This document summarizes the PIE performed at the ORNL LAMDA laboratory. The results of the PIE described in this report are consistent with the ultrasonic data collected during irradiation – in particular, high temperature epoxy adhesive seemed to provide the best coupling as compared to the refractory ceramic adhesives. It was determined that the quality of the sensor-adhesive-substrates governed the ultrasonic performance of the sensors. It was also apparent that irradiation did not significantly affect bond quality, which is also supported by the ultrasonic data collected during irradiation. A more comprehensive DOE NSUF Final Report including details of materials selection, sample fabrication, initial ultrasonic testing, irradiation and in-situ ultrasonic testing, positron annihilation lifetime spectroscopy and doppler broadening spectroscopy performed at EPRI and NC State University will be published at the conclusion of the project.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Assessing the coating implications of slurry formulations in NCMA and LFMP blend cathodes for lithium-ion batteries

This paper investigates the implications of slurry formulations and electrode processing on the performance of lithium-ion battery (LIB) cathodes, focusing on Nickel Cobalt Manganese Aluminum (NCMA) and Lithium Ferro Manganese Phosphate (LFMP) blends. Through a comprehensive examination of electrode processing steps, from material selection to coating application, we elucidate the critical role of processing parameters in shaping electrode morphology and electrochemical behavior. Rheological studies reveal the influence of slurry composition on viscosity and flow behavior, highlighting the importance of achieving optimal rheological properties for uniform coating deposition. Electrochemical characterization, including cyclic voltammetry and rate capability tests, unveils the electrochemical behavior of NCMA, LFMP, and their blend, showcasing the synergistic effects of material blending on battery performance. In conclusion, our findings underscore the intricate relationship between slurry formulation, electrode processing, and LIB performance, offering valuable insights for the design and optimization of high-performance electrode materials for next-generation batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Large radiation back-flux from Monte Carlo simulations of fusion neutron–material interactions

Abstract Fusion power reactors will generate intense neutron fluxes into plasma-facing and structural materials (SMs). Radiation back-fluxes, generated from neutron–material interactions under these fluxes, can dramatically impact the plasma dynamics, e.g. by seeding runaway electrons during disruptions via Compton scattering of background electrons by wall-emitted gamma radiation. Here, we quantify these back-fluxes, including neutrons, gamma rays, and electrons, using Monte Carlo calculations for a range of SM candidates and first wall (FW) thicknesses. The radiation back-flux magnitudes are remarkably large, with neutron and gamma radiation back-fluxes on the same order of magnitude as the incident fusion neutron flux. Electron back-fluxes are two orders of magnitudes lower, but are emitted at sufficiently high energies to impact the sheath and boundary plasma dynamics. Material configuration plays a key role in determining back-flux magnitudes. The SM chiefly determines the neutron back-flux magnitude, while the FW thickness principally attenuates the gamma ray and electron back-fluxes. In addition to prompt back-fluxes, which are emitted immediately after fusion neutrons impact the surface, significant delayed gamma ray and electron back-fluxes arise from nuclear decay processes in the activated materials. These delayed back-flux magnitudes range from 2% to 7% of the prompt back-fluxes, and remain present during transients when fusion no longer occurs. During disruptions, build-up of delayed gamma radiation back-flux represents potential runaway electron seeding mechanisms, posing additional challenges for disruption mitigation in a power reactor compared with non-nuclear plasma operations. This work highlights the impact of these radiation back-fluxes plasma performance and demonstrates the importance of considering back-flux generation in materials selection for fusion power reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Irradiation of Advanced Cladding Specimens in the High Flux Isotope Reactor: Capsule Designs and Test Matrix

The Advanced Fuels Campaign (AFC) has initiated the Advanced Reactor Cladding (ARC) irradiation campaign to generate irradiation performance data for candidate fuel cladding concepts. The campaign includes a diverse set of ferritic/martensitic steels, oxide dispersion strengthened (ODS) alloys, FeCrAlbased alloys, coated materials, and welded cladding specimens produced through multiple US Department of Energy (DOE) programs and international collaborations. Three complementary experimental thrusts comprise the campaign: tensile testing (ARC Tensile) to rapidly screen candidate alloys, fracture toughness testing (ARC Fracture) to evaluate irradiation effects on crack resistance, and tubular weld testing (ARC Weld) to quantify irradiation-induced changes in the mechanical performance of end cap welds. This report documents the irradiation campaign design, including the selected materials, specimen types, irradiation matrix, and capsule designs for irradiation within the High Flux Isotope Reactor (HFIR). A total of 14 irradiation capsules were developed to achieve target irradiation temperatures between 300°C and 600°C and doses up to 30 dpa. Thermal analyses were performed using finite element methods to establish capsule geometries capable of achieving the desired specimen temperatures while accommodating differences in specimen geometry and material properties. The resulting capsule designs provide the basis for irradiation of the AFC-ARC experimental matrix and subsequent post-irradiation examination to assess the effects of neutron irradiation on advanced cladding materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Materials Assessment for FLiBe Fusion Blankets

This evaluation was prepared at the request of DOE-FES and expands on an earlier evaluation prepared by Wilson, Wiffen and Keiser in 2015 (attached as Appendices A and B). Additional useful information for materials in fission molten salt reactor systems that use FLiBe can be found in a prior NRC report [Busby 2019]. The purpose of this report is to review the considerations that will determine the fusion blanket structural materials that will be suitable for use in a FLiBe breeder-coolant fusion power plant (FPP). Identifying a fusion-relevant structural material that is sufficiently compatible with FLiBe is a key issue to be addressed. The constraints and trade-offs made in structural materials selection include the usual power generation requirements such as mechanical properties, fabricability and durability, which assumes reasonable compatibility with the working fluid. For an FPP, additional constraints include neutron economy (breeding ratio), resistance to irradiation damage and low activation (i.e. waste disposal) characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding Process–Structure Relationships during Lamination of Halide Perovskite Interfaces

Fabrication of halide perovskite (HP) solar cells typically involves the sequential deposition of multiple layers to create a device stack, which is limited by the thermal and chemical incompatibility of top contact layers with the underlying HP semiconductor. One emerging strategy to overcome these restrictions on material selection and processing conditions is lamination, where two half-stacks are independently processed and then diffusion bonded to complete the device. Lamination reduces the processing constraints on the top side of the solar cell to allow new device designs, expanded use of deposition methods, and self-encapsulation of devices. While laminated perovskite solar cells with high efficiencies and novel interlayer combinations have been demonstrated, there is a limited understanding of how the lamination process parameters affect the diffusion-bond quality and material properties of the resulting HP layer. In this study, we systematically vary temperature, pressure, and time during lamination and quantify the resulting impacts on bonded area, grain domain size, and photoluminescence. A design of experiments is performed, and statistical analysis of the experimental results is used to quantitatively evaluate the resulting process–structure–property relationships. The lamination temperature is found to be the key parameter controlling these properties. Furthermore, a temperature of 150 °C enables successful bonding over 95% of the substrate area and also results in increases in apparent grain domain size and photoluminescence intensity. Based on these insights, the lamination temperature of functional perovskite solar cell devices is varied, demonstrating the importance of the resulting bond quality on device performance metrics.

14 SOLAR ENERGY↗
DOE OSTI2024

MaterialsMap: A CALPHAD-based tool to design composition pathways through feasibility map for desired dissimilar materials, demonstrated with resistance spot welding joining of Ag-Al-Cu

Assembly of dissimilar metals can be achieved by different methods, for example, casting, welding, and additive manufacturing (AM). However, undesired phases formed in liquid-phase assembling processes due to solute segregation during solidification diminish mechanical and other properties of the processed parts. In the present work, an open-source software named MaterialsMap, has been developed based on the CALculation of Phase Diagrams (CALPHAD) approach. The primary objective of MaterialsMap is to facilitate the design of an optimal composition pathway for assembling dissimilar alloys with liquid-phases based on the formation of desired and undesired phases along the pathway. In MaterialsMap, equilibrium thermodynamic calculations are used to predict equilibrium phases formed at slow cooling rate, while Scheil-Gulliver simulations are employed to predict non-equilibrium phases formed during rapid cooling. Additionally, by combining these two simulations, MaterialsMap offers a thorough guide for understanding phase formation in various manufacturing processes, assisting users in making informed decisions during material selection and production. As a demonstration of this approach, a compositional pathway was designed from pure Al to pure Cu through Ag using MaterialsMap. The design was experimentally verified using resistance spot welding (RSW).

36 MATERIALS SCIENCE↗
DOE OSTI2024

The influence of electrode crack dimensions on the durability of polymer electrolyte membrane fuel cells

Electrode cracks in polymer electrolyte membrane fuel cells (PEMFCs) are correlated with early onset failures. Here, in this work we investigate the influence of cracked gas diffusion electrodes (GDEs) on the durability of the membrane electrode assembly (MEA) using a combined chemical-mechanical accelerated stress test (AST). Electrode crack dimensions were systematically tuned using ink formulations and material selection strategies. A parameter to describe the crack width areal density (Φ CW ) was used to quantify the degree of discontinuity in the electrode surfaces. Open circuit voltage (OCV) transient analyses were used to benchmark and characterize the failure mechanisms in the MEAs as a function of the Φ CW . While smaller electrode-level cracks, on the order of microns, yielded a 28 % decrease in operating lifetime, larger cracks that propagated from a discontinuous, microporous layer (MPL) coating, decreased the operating lifetime by 56 %. This work emphasizes the need for material processing strategies that consider defect tolerances to limit membrane failures in PEMFCs.

08 HYDROGEN↗
DOE OSTI2024

Update on Activities Related to the Library of Graphite Microstructures

This report provides an overview and update of the ongoing efforts to create a comprehensive library of microstructures for nuclear graphite and carbon-based materials under consideration for nuclear applications. The library includes data on microstructural characterization of unirradiated graphite materials, a guide to the techniques used to analyze graphite (which complements the ASME guidelines and ASTM standards), a summary of characterization data for neutron-irradiated or oxidized material, and a compendium of microstructural information for carbon-based materials. These efforts are being conducted at various length scales for the filler and binder phases in graphite to better understand graphite’s local structure and property relationships. This report is a follow-up to the previous milestone report titled Report on initial development of a database of nuclear graphite characteristics based on microstructural characterization, ORNL/TM/-2023/2992, published in July 2023.The effort to develop the library of microstructures supports the US Department of Energy Office of Advanced Reactor Technologies program objectives of aiding the material selection, licensing, management, and core assessments of a graphite core by documenting the unirradiated microstructure of relevant grades or characterizing the microstructure’s evolution under the reactor environment. Additionally, this project aims to provide (1) information and guidelines for the characterizing of graphite and (2) a protocol to assess a nuclear graphite grade.

36 MATERIALS SCIENCE↗