SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The wave representation and scattering matrix of n-ports is discussed. This representation is particularly suited to the treatment of microwave switching.
During the summer of 1994, the performance of an experimental mobile satellite communication system was demonstrated to the industry and government representatives by the NASA Lewis Research Center (LeRC) and the Jet Propulsion Laboratory (JPL). The system was based on the Advanced Communications Technology Satellite (ACTS) and consisted of an K-/Ka-band active MMIC phased array antenna system, ACTS Mobile Terminal (AMT) and Link Evaluation Terminal (LET). A LeRC research aircraft, Learjet Model 25, was outfitted with the active MMIC phased array antenna system and AMT and served as the experimental 20/30 Ghz aeronautical terminal. The LET at LeRC in Cleveland, OH was interfaced with portions of fixed-AMT equipment and together provided the gateway station functions including ACTS satellite interface and Public Service Telephone Network (PSTN) interface. The ACTS was operated in its Microwave Switch Matrix (MSM) mode with a spot beam for the Learjet and another spot beam dedicated to the LET. The Learjet was flown over several major cities across the US and demonstrated the feasibility of full-duplex compressed voice link for an aeronautical terminal through the 20/30 Ghz ACTS satellite channel. This paper will present a technical description of the system including the MMIC phased array antenna system, AMT, Learjet, LET and ACTS satellite. The array antenna system consists of a 30 Ghz transmit array (LeRC/Texas Instruments) and two 20 Ghz receive arrays (USAF Rome Lab/Boeing and Martin Marietta), each one very small with sufficient performance for satellite voice link. The AMT consists of 2.4/4.8/9.6 Kbps voice coder/decoder, modem, PSTN interface and RF/IF converters. Link analysis will be presented and compared to the actual performance data collected during the demonstration flights.
During the summer of 1994, the performance of an experimental mobile satellite communication system was demonstrated to industry and government representatives by the NASA Lewis Research Center (LeRC) and the Jet Propulsion Laboratory (JPL). The system was based on the advanced communications technology satellite (ACTS) and consisted of a K-/Ka-band active monolithic microwave integrated circuit (MMIC) phased array antenna system, ACTS mobile terminal (AMT) and link evaluation terminal (LET). A LeRC research aircraft, Learjet model 25, was outfitted with the active MMIC phased array antenna system and AMT and served as the experimental 20/30 Ghz aeronautical terminal. The LET at LeRC in Cleveland, OH, was interfaced with portions of fixed-AMT equipment and together provided the gateway station functions including ACTS interface and public service telephone network (PSTN) interface. The ACTS was operated in its microwave switch matrix (MSM) mode with a spot beam for the Learjet and another spot beam dedicated to the LET. The Learjet was flown over several major cities across the US and demonstrated the feasibility of a full-duplex compressed voice links for an aeronautical terminal through the 20/30 Ghz ACTS channel. This paper presents a technical description of the system including the MMIC phased array antenna system, AMT, Learjet, LET, and ACTS. The array antenna system consists of a 30 Ghz transmit array (LeRc/Texas Instruments) and two 20 Ghz receive arrays (USAF Rome Lab., Boeing, and Martin Marietta), each one very small with sufficient performance for a satellite voice link. The AMT consists of 2.4/4.8/9.6 Kbps voice coder/decoder, modem, PSTN interface and RF/IF converters. Link analysis is presented and compared to the actual performance data collected during the demonstration flights.
The Advanced Communications Technology Satellite (ACTS) was conceived at the National Aeronautics and Space Administration (NASA) in the late 1970's as a follow-on program to ATS and CTS to continue NASA's long history of satellite communications projects. The ACTS project set the stage for the C-band satellites that started the industry, and later the ACTS project established the use of Ku-band for video distribution and direct-to-home broadcasting. ACTS, launched in September 1993 from the space shuttle, created a revolution in satellite system architecture by using digital communications techniques employing key technologies such as a fast hopping multibeam antenna, an on-board baseband processor, a wide-band microwave switch matrix, adaptive rain fade compensation, and the use of 900 MHz transponders operating at Ka-band frequencies. This paper describes the lessons learned in each of the key ACTS technology areas, as well as in the propagation investigations.
During the summer of 1994, the performance of an experimental mobile satellite communication system was demonstrated. Using the Advanced Communications Technology Satellite (ACTS) and the ACTS Mobile Terminal (AMT), the system demonstrated an active Monolithic Microwave Integrated Circuit (MMIC) phased-array antenna system. The antenna system was installed onboard one of NASA Lewis Research Center's research aircraft, a Learjet Model 25. It proved the viability of in-flight satellite communications services via small, flush, mountable electronic phased-array antennas. The overall system setup for the ACTS Aeronautical Terminal Experiment (AERO-X) is illustrated. The Link Evaluation Terminal (LET) at Lewis in Cleveland, Ohio, interfaced with fixed-AMT equipment, providing a seamless connection with the Public Service Telephone Network. As the Learjet was flown over several major cities across the U.S., this demonstration system allowed passengers onboard to make telephone calls as if they were using a cellular system. ACTS was operated in its microwave switch matrix mode with a spot beam for the Learjet and another spot beam dedicated to the LET.
The performance of semiconductor and high critical temperature superconductor switches is compared as they are used in delay-line-type microwave and millimeter-wave phase shifters. Such factors as their ratios of the off-to-on resistances, parasitic reactances, power consumption, speed, input-to-output isolation, ease of fabrication, and physical dimensions are compared. Owing to their almost infinite off-to-on resistance ratio and excellent input-to-output isolation, bolometric superconducting switches appear to be quite suitable for use in microwave phase shifters; their only drawbacks are their speed and size. The SUPERFET, a novel device whose operation is based on the electric field effect in high critical temperature ceramic superconductors is also discussed. Preliminary results indicate that the SUPERFET is fast and that it can be scaled; therefore, it can be fabricated with dimensions comparable to semiconductor field-effect transistors.
The performance of semiconductor and high critical temperature superconductor switches is compared as they are used in delay-line-type microwave and millimeter-wave phase shifters. Such factors as their ratios of the off-to-on resistances, parasitic reactances, power consumption, speed, input-to-output isolation, ease of fabrication, and physical dimensions are compared. Owing to their almost infinite off-to-on resistance ratio and excellent input-to-output isolation, bolometric superconducting switches appear to be quite suitable for use in microwave phase shifters; their only drawbacks are their speed and size. The SUPERFET, a novel device whose operation is based on the electric field effect in high critical temperature ceramic superconductors is also discussed. Preliminary results indicate that the SUPERFET is fast and that it can be scaled; therefore, it can be fabricated with dimensions comparable to semiconductor field-effect transistors.
Receiver remains connected to both antennas, transmitter switched to connect it to one or other. Combination of hybrid junction, circulators, and filter provides simultaneous reception paths from both antennas without significantly altering radiation patterns of antennas. Communication system considered for use in spacecraft and in which mechanical switch permitted on downlink but not on uplink. Applicable to terrestrial microwave communication stations subject to dual-antenna requirements.
Switches, electrical components that either permit or prevent the flow of electricity, are the most important and widely used electrical devices in integrated circuits. In microwave systems, switches are required for switching between the transmitter and receiver; in communication systems, they are needed for phase shifters in phased-array antennas, for radar and communication systems, and for the new class of digital or software definable radios. Ideally, switches would be lossless devices that did not depend on the electrical signal's frequency or power, and they would not consume electrical power to change from OFF to ON or to maintain one of these two states. Reality is quite different, especially at microwave frequencies. Typical switches in microwave integrated circuits are pin diodes or gallium arsenide (GaAs) field-effect transistors that are nonlinear, with characteristics that depend on the power of the signal. In addition, they are frequency-dependent, lossy, and require electrical power to maintain a certain state. A new type of component has been developed that overcomes most of these technical difficulties. Microelectromechanical (MEMS) switches rely on mechanical movement as a response to an applied electrical force to either transmit or reflect electrical signal power. The NASA Glenn Research Center has been actively developing MEMS for microwave applications for over the last 5 years. Complete fabrication procedures have been developed so that the moving parts of the switch can be released with near 100-percent yield. Moreover, the switches fabricated at Glenn have demonstrated state-of-the-art performance. A typical MEMS switch is shown. The switch extends over the signal and ground lines of a finite ground coplanar waveguide, a commonly used microwave transmission line. In the state shown, the switch is in the UP state and all the microwave power traveling along the transmission line proceeds unimpeded. When a potential difference is applied between the cantilever and the transmission line, the cantilever is pulled downward until it connects the signal line to the ground planes, creating a short circuit. In this state, all the microwave power is reflected. The graph shows the measured performance of the switch, which has less than 0.1 dB of insertion loss and greater than 30dB of isolation. These switches consume negligible electrical power and are extremely linear. Additional research is required to address reliability and to increase the switching speed.
In multiple-port microwave power combiner, each of outputs of two or more power amplifiers of same frequency and phase passed to common output port separately or together. Each amplifier connected to combiner through switch consisting of resonant structures, radio-frequency chokes, and diode. Switches not only permit flexiblity in selection of amplifiers but isolate unused amplifiers from network, all while operating at relatively low power loss.
Laser-activated microwave semiconductor device switches at microwave speeds, generates pulses, or detects optical pulses with fast response. Device consists essentially of back-to-back metal/thin oxide/silicon (MTOS) capacitors on silicon chip.
In this presentation, we describe the fabrication of micro-electro-mechanical system (MEMS) devices, in particular, of low-frequency multi-element electrical switches using SiO2 cantilevers. The switches discussed are related to micromechanical membrane structures used to perform switching of optical signals on silicon substrates. These switches use a thin metal membrane which is actuated by an electrostatic potential, causing the switch to make or break contact. The advantages include: superior isolation, high power handling capabilities, high radiation hardening, very low power operations, and the ability to integrate onto GaAs monolithic microwave integrated circuit (MMIC) chips.
The design and fabrication of a 3-8 GHz, 20 x 20 Satellite Switched-Time Division Multiple Access IF switch matrix applicable to a 30/20 GHz communications satellite are described. An assessment of switch architecture in 1980 concluded that the GaAs FET-based coupled crossbar switch matrix, incorporating high speed CMOS LSI logic for switch crosspoint addressing, would be the optimum technology available for communications satellite switching by 1982. This assessment was based on such factors as switching speed, bandwidth, off-state isolation, and reliability, over a 10-year mission life. A proof-of-concept model's construction and testing are presented.
Combiner system can be used for combining output powers of two transmitters or for switching from one to the other. This can be done when pair of transmitters operate on same frequency and carriers are phase coherent as by excitation from single exciter.
Beam switching Cassegrain antenna for millimeter wave radio astronomical measurements, describing RF and electronic systems
Microwave signals switched or modulated optically. Planar diode with transparent cathode made in BaAs, Si, and InSb versions. Depending on specific configuration and material, such diode used for optical modulation of microwave signal or as infrared detector. Transparent cathode fabricated on GaAs diode so diode illuminates to generate and control short-circuit current.
The Advanced Communications Technology Satellite (ACTS) was sponsored by NASA to develop the technology for 30/20 Ghz, spot beam communications satellites with on-board baseband and microwave matrix switching. The spot beams allow the use of very small aperture, low cost terminals as well as provide a large degree of frequency reuse. These technologies also significantly reduce the on-orbit weight per unit communication capacity. The ACTS system provides, for the most part, on-demand, integrated digital satellite /terrestrial networks with service data rates from 64 Kbps to 622 Mbps. This paper discusses the results obtained from the ACTS development and its first two years of on-orbit operations for fixed and mobile services.
The goal of this technology is to provide improved calibration and measurement sensitivity to the Soil Moisture Active Passive Mission (SMAP) radiometer. While RF switches have been used in the past to calibrate microwave radiometers, the switch used on SMAP employs several techniques uniquely tailored to the instrument requirements and passive remote-sensing in general to improve radiometer performance. Measurement error and sensitivity are improved by employing techniques to reduce thermal gradients within the device, reduce insertion loss during antenna observations, increase insertion loss temporal stability, and increase rejection of radar and RFI (radio-frequency interference) signals during calibration. The two legs of the single-pole double-throw reference switch employ three PIN diodes per leg in a parallel-shunt configuration to minimize insertion loss and increase stability while exceeding rejection requirements at 1,413 MHz. The high-speed packaged diodes are selected to minimize junction capacitance and resistance while ensuring the parallel devices have very similar I-V curves. Switch rejection is improved by adding high-impedance quarter-wave tapers before and after the diodes, along with replacing the ground via of one diode per leg with an open circuit stub. Errors due to thermal gradients in the switch are reduced by embedding the 50-ohm reference load within the switch, along with using a 0.25-in. (approximately equal to 0.6-cm) aluminum prebacked substrate. Previous spaceflight microwave radiometers did not embed the reference load and thermocouple directly within the calibration switch. In doing so, the SMAP switch reduces error caused by thermal gradients between the load and switch. Thermal issues are further reduced by moving the custom, highspeed regulated driver circuit to a physically separate PWB (printed wiring board). Regarding RF performance, previous spaceflight reference switches have not employed high-impedance tapers to improve rejection. The use of open-circuit stubs instead of a via to provide an improved RF short is unique to this design. The stubs are easily tunable to provide high rejection at specific frequencies while maintaining very low insertion loss in-band.