Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mars Transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Navigating MarCO, the first interplanetary CubeSats

The NASA’s Mars Cube One (MarCO) probes are twin 6U CubeSats that were launched into space on May 5, 2018. The MarCOs shared a launch vehicle with NASA’s InSight mission, separating from the Atlas V Centaur upper stage after InSight. The MarCOs were injected into an Earth-Mars transfer trajectory and were independently navigated to the proximity of Mars. On 26 November, 2018 the MarCO probes flew by Mars as the InSight lander descended to the surface, providing real-time relay of InSight UHF data back to the Earth. This paper describes the approaches used to design the MarCOs’ trajectories and to navigate them to Mars, presenting the challenges of navigating and operating CubeSats in deep space, and the technological firsts achieved by the MarCO mission.

Young, Brian↗
NASA NTRS1992

Engine system assessment study using Martian propellants

A top-level feasibility study was conducted that identified and characterized promising chemical propulsion system designs which use two or more of the following propellant combinations: LOX/H2, LOX/CH4, and LOX/CO. The engine systems examined emphasized the usage of common subsystem/component hardware where possible. In support of this study, numerous mission scenarios were characterized that used various combinations of Earth, lunar, and Mars propellants to establish engine system requirements to assess the promising engine system design concept examined, and to determine overall exploration leverage of such systems compared to state-of-the-art cryogenic (LOX/H2) propulsion systems. Initially in the study, critical propulsion system technologies were assessed. Candidate expander and gas generator cycle LOX/H2/CO, LOX/H2/CH4, and LOX/CO/CH4 engine system designs were parametrically evaluated. From this evaluation baseline, tripropellant Mars Transfer Vehicle (MTV) LOX cooled and bipropellant Lunar Excursion Vehicle (LEV) and Mars Excursion Vehicle (MEV) engine systems were identified. Representative tankage designs for a MTV were also investigated. Re-evaluation of the missions using the baseline engine design showed that in general the slightly lower performance, smaller, lower weight gas generator cycle-based engines required less overall mission Mars and in situ propellant production (ISPP) infrastructure support compared to the larger, heavier, higher performing expander cycle engine systems.

Pelaccio, Dennis↗
NASA NTRS2020

Multi-Impulse to Time Optimal Finite Burn Trajectory Conversion

A novel conversion algorithm is presented that combines the fidelity of indirect optimization methods with the generality of direct methods to more easily solve time-optimal, finite-burn pseudo-rendezvous problems. An algorithm is described that converts a set of multiple-impulses, representing the entirety or a portion of a high- or low-thrust maneuver, to an exact time optimal finite-burn trajectory for a thrust limited, constant exhaust velocity spacecraft. A pseudo-rendezvous problem is one that yields a solution whose final time, position and velocity state is equal to that of the original post-impulsive trajectory. An iterative adjoint-control transformation is used to initialize the optimal control two-point boundary value problem. Examples are shown for both high and low-thrust non-coplanar Earth orbit transfers, as well as a low-thrust Hohmann-type Earth-Mars transfer.

Fogel, J.↗
NASA NTRS1990

Assembly vs. direct launch of transfer vehicles

A top level assessment is performed of the relative impacts of on-orbit assembly of the lunar or Mars transfer vehicles versus direct launch. The objective is to identify the major option paths for the Earth-to-orbit, ETO, transportation systems. Heavy lift launch vehicles, if large enough, could reduce or eliminate on-orbit assembly. However, with every new approach, there are always counter-balancing considerations and it is the objective to begin the delineation of the necessary follow-on trade study issues.

Katzberg, Stephen J.↗
NASA NTRS2010

Analysis of Shroud Options in Support of the Human Exploration of Mars

In support of the Mars Design Reference Architecture (DRA) 5.0, the NASA study team analyzed several shroud options for use on the Ares V launch vehicle.1,2 These shroud options included conventional "large encapsulation" shrouds with outer diameters ranging from 8.4 to 12.9 meters (m) and overall lengths of 22.0 to 54.3 meters, along with a "nosecone-only" shroud option used for Mars transfer vehicle component delivery. Also examined was a "multi-use" aerodynamic encapsulation shroud used for launch, Mars aerocapture, and entry, descent, and landing of the cargo and habitat landers. All conventional shroud options assessed for use on the Mars launch vehicles were the standard biconic design derived from the reference shroud utilized in the Constellation Program s lunar campaign. It is the purpose of this paper to discuss the technical details of each of these shroud options including material properties, structural mass, etc., while also discussing both the volume and mass of the various space transportation and surface system payload elements required to support a "minimum launch" Mars mission strategy, as well as the synergy, potential differences and upgrade paths that may be required between the Lunar and Mars mission shrouds.

Feldman, Stuart↗
NASA NTRS2012

Modular Growth NTR Space Transportation System for Future NASA Human Lunar, NEA and Mars Exploration Missions

The nuclear thermal rocket (NTR) is a proven, high thrust propulsion technology that has twice the specific impulse (I(sub sp) approx.900 s) of today's best chemical rockets. During the Rover and NERVA (Nuclear Engine for Rocket Vehicle Applications) programs, twenty rocket reactors were designed, built and ground tested. These tests demonstrated: (1) a wide range of thrust; (2) high temperature carbide-based nuclear fuel; (3) sustained engine operation; (4) accumulated lifetime; and (5) restart capability - everything required for affordable human missions beyond LEO. In NASA's recent Mars Design Reference Architecture (DRA) 5.0 study, the NTR was selected as the preferred propulsion option because of its proven technology, higher performance, lower IMLEO, versatile vehicle design, and growth potential. Furthermore, the NTR requires no large technology scale-ups since the smallest engine tested during the Rover program - the 25 klb(sub f) "Pewee" engine is sufficient for human Mars missions when used in a clustered engine configuration. The "Copernicus" crewed Mars transfer vehicle developed for DRA 5.0 was an expendable design sized for fast-conjunction, long surface stay Mars missions. It therefore has significant propellant capacity allowing a reusable "1-year" round trip human mission to a large, high energy near Earth asteroid (NEA) like Apophis in 2028. Using a "split mission" approach, Copernicus and its two key elements - a common propulsion stage and integrated "saddle truss" and LH2 drop tank assembly - configured as an Earth Return Vehicle / propellant tanker, can also support a short round trip (approx.18 month) / short orbital stay (60 days) Mars reconnaissance mission in the early 2030's before a landing is attempted. The same short stay orbital mission can be performed with an "all-up" vehicle by adding an "in-line" LH2 tank to Copernicus to supply the extra propellant needed for this higher energy, opposition-class mission. To transition to a reusable Mars architecture, Copernicus' saddle truss / drop tank assembly is replaced by an in-line tank and "star truss" assembly with paired modular drop tanks to further increase the vehicle's propellant capacity. Shorter "1-way" transit time fast-conjunction Mars missions are another possibility using this vehicle configuration but, as with reusability, increased launch mass is required. "Scaled down" versions of Copernicus (sized to a SLS lift capability of approx.70 t - 100 t) can be developed initially allowing reusable lunar cargo delivery and crewed landing missions, easy NEA missions (e.g., 2000 SG344 also in 2028) or an expendable mission to Apophis. Mission scenario descriptions, key vehicle features and operational characteristics are provided along with a brief discussion of NASA's current activities and its "pre-decisional" plans for future NTR development.

Borowski, Stanley K.↗
NASA NTRS1991

Space Station Freedom/lunar transfer vehicle propellant operation hazard analysis

Space Station Freedom (SSF), as a transportation node for Space Exploration Initiative missions, would involve the assembly and refurbishing of lunar and Mars transfer vehicles. This includes operations involving cryogenic propellants (LH2 7 LO2) such as storing and handling of loaded propellant tanks, assembly onto the vehicle, and propellant transfer. Cryogenic propellants dictate rigorous safety precautions and impose unique requirements to ensure flight safety to both personnel and SSF elements. The objective of this study is to identify potential hazards and risks associated with cryogenic propellants. This involves identification of pertinent system design features and operational procedures. Criticality of identified risks/hazards shall be assessed and those that fall in the catastrophic and critical categories shall include mitigating solutions.

Dominick, Sam↗
NASA NTRS1990

Metallized Propellants for the Human Exploration of Mars

Advanced chemical propulsion using Metallized Propellants (MP) can lead to significant reductions in launch mass for piloted Mars missions. MP allow the propellant density or the specific impulse I(sub sp) of the propulsion system, or both, to increase. It can reduce the propellant mass and the propulsion system dry mass. Detailed mass-scaling equations and estimates of the I(sub sp) for several MP combinations are presented. The most significant savings with MP are derived from increasing the payload delivered to Mars. For the mass in low Earth orbit (LEO), a metallized Mars transfer vehicle can deliver 20 to 22 percent additional payload. This 20-percent payload increase reduces the total number of Mars flights and therefore significantly reduces the number of Space Transportation System-Cargo launches for the entire Mars architecture. Using MP to reduce the mass in LEO per flight is not as effective as increasing the payload delivery capacity. The mass saving per flight, while delivering the same payload with a higher I(sub sp) system, is much smaller. Using MP in all of the Mars propulsion systems would produce a modest 3.3 percent LEO mass saving. This translates into a saving of 38,000 kg over the mass required with O2/H2 propulsion. A Mars excursion vehicle using Earth- or space-storable propellants for the ascent can be an alternative to storing cryogenic H2 on Mars. A space-storable system using oxygen/monomethyl hydrazine/aluminum (O2/MMH/Al) would deliver the lowest mass penalty over O2/H2. For lower-energy expedition missions the LEO mass penalty for using metallized O2/MMH/Al would be only 3 to 5 percent.

Palaszewski, Bryan A.↗
NASA NTRS2012

Near Earth Asteroid Human Mission Possibilities Using Nuclear Thermal Rocket (NTR) Propulsion

The NTR is a proven technology that generates high thrust and has a specific impulse (Isp (is) approximately 900 s) twice that of today's best chemical rockets. During the Rover and NERVA (Nuclear Engine for Rocket Vehicle Applications) programs, twenty rocket reactors were designed, built and ground tested. These tests demonstrated: (1) a wide range of thrust; (2) high temperature carbide-based nuclear fuel; (3) sustained engine operation; (4) accumulated lifetime; and (5) restart capability - all the requirements needed for a human mission to Mars. Ceramic metal fuel was also evaluated as a backup option. In NASA's recent Mars Design reference Architecture (DRA) 5.0 study, the NTR was selected as the preferred propulsion option because of its proven technology, higher performance, lower launch mass, versatile vehicle design, simple assembly, and growth potential. In contrast to other advanced propulsion options, NTP requires no large technology scale-ups. In fact, the smallest engine tested during the Rover program - the 25 klbf 'Pewee' engine is sufficient for a human Mars mission when used in a clustered engine configuration. The 'Copernicus crewed NTR Mars transfer vehicle design developed for DRA 5.0 has significant capability that can enable reusable '1-year' round trip human missions to candidate near Earth asteroids (NEAs) like 1991 JW in 2027, or 2000 SG344 and Apophis in 2028. A robotic precursor mission to 2000 SG344 in late 2023 could provide an attractive Flight Technology Demonstration of a small NTR engine that is scalable to the 25 klbf-class engine used for human missions 5 years later. In addition to the detailed scientific data gathered from on-site inspection, human NEA missions would also provide a valuable 'check out' function for key elements of the NTR transfer vehicle (its propulsion module, TransHab and life support systems, etc.) in a 'deep space' environment prior to undertaking the longer duration Mars orbital and landing missions that would follow. The initial mass in low Earth orbit required for a mission to Apophis is approximately 323 t consisting of the NTR propulsion module ((is) approximately 138 t), the integrated saddle truss and LH2 drop tank assembly ((is) approximately 123 t), and the 6-crew payload element ((is) approximately 62 t). The later includes a multi-mission Space Excursion Vehicle (MMSEV) used for close-up examination and sample gathering. The total burn time and required restarts on the three 25 klbf 'Pewee-class' engines operating at Isp (is) approximately 906 s, are approximately 76.2 minutes and 4, respectively, well below the 2 hours and 27 restarts demonstrated on the NERVA eXperimental Engine, the NRX-XE. The paper examines the benefits, requirements and characteristics of using NTP for the above NEA missions. The impacts on vehicle design of HLV payload volume and lift capability, crew size, and reusability are also quantified.

Borowski, Stanley↗
NASA NTRS2009

Power Requirements for The NASA Mars Design Reference Architecture (DRA) 5.0

This paper summarizes the power systems analysis results from NASA s recent Mars DRA 5.0 study which examined three architecture options and resulting mission requirements for a human Mars landing mission in the post-2030 timeframe. DRA 5.0 features a long approximately 500 day surface stay split mission using separate cargo and crewed Mars transfer vehicles. Two cargo flights, utilizing minimum energy trajectories, pre-deploy a cargo lander to the surface and a habitat lander into a 24-hour elliptical Mars parking orbit where it remains until the arrival of the crew during the next mission opportunity approximately 26 months later. The pre-deployment of cargo poses unique challenges for set-up and emplacement of surface assets that results in the need for self or robotically deployed designs. Three surface architecture options were evaluated for breadth of science content, extent of exploration range/capability and variations in system concepts and technology. This paper describes the power requirements for the surface operations of the three mission options, power system analyses including discussion of the nuclear fission, solar photovoltaic and radioisotope concepts for main base power and long range mobility.

Cataldo, Robert L.↗
NASA NTRS1991

Trajectory and navigation system design for robotic and piloted missions to Mars

Future Mars exploration missions, both robotic and piloted, may utilize Earth to Mars transfer trajectories that are significantly different from one another, depending upon the type of mission being flown and the time period during which the flight takes place. The use of new or emerging technologies for future missions to Mars, such as aerobraking and nuclear rocket propulsion, may yield navigation requirements that are much more stringent than those of past robotic missions, and are very difficult to meet for some trajectories. This article explores the interdependencies between the properties of direct Earth to Mars trajectories and the Mars approach navigation accuracy that can be achieved using different radio metric data types, such as ranging measurements between an approaching spacecraft and Mars orbiting relay satellites, or Earth based measurements such as coherent Doppler and very long baseline interferometry. The trajectory characteristics affecting navigation performance are identified, and the variations in accuracy that might be experienced over the range of different Mars approach trajectories are discussed. The results predict that three sigma periapsis altitude navigation uncertainties of 2 to 10 km can be achieved when a Mars orbiting satellite is used as a navigation aid.

Thurman, S. W.↗
NASA NTRS1991

Trajectory and navigation system design for robotic and piloted missions to Mars

Future Mars exploration missions, both robotic and piloted, may utilize Earth to Mars transfer trajectories that are significantly different from one another, depending upon the type of mission being flown and the time period during which the flight takes place. The use of new or emerging technologies for future missions to Mars, such as aerobraking and nuclear rocket propulsion, may yield navigation requirements that are much more stringent than those of past robotic missions, and are very difficult to meet for some trajectories. This article explores the interdependencies between the properties of direct Earth to Mars trajectories and the Mars approach navigation accuracy that can be achieved using different radio metric data types, such as ranging measurements between an approaching spacecraft and Mars orbiting relay satellites, or Earth based measurements such as coherent Doppler and very long baseline interferometry. The trajectory characteristics affecting navigation performance are identified, and the variations in accuracy that might be experienced over the range of different Mars approach trajectories are discussed. The results predict that three sigma periapsis altitude navigation uncertainties of 2 to 10 km can be achieved when a Mars orbiting satellite is used as a navigation aid.

Thurman, S. W.↗
NASA NTRS2013

Launch and Assembly Reliability Analysis for Mars Human Space Exploration Missions

NASA s long-range goal is focused upon human exploration of Mars. Missions to Mars will require campaigns of multiple launches to assemble Mars Transfer Vehicles in Earth orbit. Launch campaigns are subject to delays, launch vehicles can fail to place their payloads into the required orbit, and spacecraft may fail during the assembly process or while loitering prior to the Trans-Mars Injection (TMI) burn. Additionally, missions to Mars have constrained departure windows lasting approximately sixty days that repeat approximately every two years. Ensuring high reliability of launching and assembling all required elements in time to support the TMI window will be a key enabler to mission success. This paper describes an integrated methodology for analyzing and improving the reliability of the launch and assembly campaign phase. A discrete event simulation involves several pertinent risk factors including, but not limited to: manufacturing completion; transportation; ground processing; launch countdown; ascent; rendezvous and docking, assembly, and orbital operations leading up to TMI. The model accommodates varying numbers of launches, including the potential for spare launches. Having a spare launch capability provides significant improvement to mission success.

Cates, Grant R.↗
NASA NTRS2006

Overview of Small and Large-Scale Space Solar Power Concepts

An overview of space solar power studies performed at the Boeing Company under contract with NASA will be presented. The major concepts to be presented are: 1. Power Plug in Orbit: this is a spacecraft that collects solar energy and distributes it to users in space using directed radio frequency or optical energy. Our concept uses solar arrays having the same dimensions as ISS arrays, but are assumed to be more efficient. If radiofrequency wavelengths are used, it will necessitate that the receiving satellite be equipped with a rectifying antenna (rectenna). For optical wavelengths, the solar arrays on the receiving satellite will collect the power. 2. Mars Clipper I Power Explorer: this is a solar electric Mars transfer vehicle to support human missions. A near-term precursor could be a high-power radar mapping spacecraft with self-transport capability. Advanced solar electric power systems and electric propulsion technology constitute viable elements for conducting human Mars missions that are roughly comparable in performance to similar missions utilizing alternative high thrust systems, with the one exception being their inability to achieve short Earth-Mars trip times. 3. Alternative Architectures: this task involves investigating alternatives to the traditional solar power satellite (SPS) to supply commercial power from space for use on Earth. Four concepts were studied: two using photovoltaic power generation, and two using solar dynamic power generation, with microwave and laser power transmission alternatives considered for each. All four architectures use geostationary orbit. 4. Cryogenic Propellant Depot in Earth Orbit: this concept uses large solar arrays (producing perhaps 600 kW) to electrolyze water launched from Earth, liquefy the resulting hydrogen and oxygen gases, and store them until needed by spacecraft. 5. Beam-Powered Lunar Polar Rover: a lunar rover powered by a microwave or laser beam can explore permanently shadowed craters near the lunar poles to search for water ice and other frozen volatiles. Near such craters are mountain peaks and highlands that are in near permanent sunlight. Power can be beamed from a collector on a sunlit mountain or crater rim to a rover inside a crater. Near-term applications of space solar power technology can therefore pave the way toward large-scale commercial power from space.

Potter, Seth↗
NASA NTRS1990

STS Derivative Cargo Vehicles for the 1990's decade and beyond

Shuttle-derived vehicle options are described in the context of supporting earth-LEO space transportation for the lunar and Mars missions. An evolutionary model is delineated which can provide heavy-lift capabilities for these missions with a system based on STS booster elements. The Shuttle-C unmanned launch system and the Mars heavy-lift launch vehicles (HLLV) are examined as reference vehicles with launch configurations illustrated for lunar and Martian transportation scenarios. The Shuttle-C prelunar vehicle can be modified for lunar transportation as the Shuttle-C Block I which can then be extended to a two-stage HLLV by adding a third stage in the form of a Mars transfer vehicle. The development of a liquid-rocket booster is proposed to replace the STS solid booster for added mission flexibility. The use of shuttle-derived vehicles is concluded to be an effective means for supporting the lunar and Mars initiatives while minimizing near-term costs.

Shelton, Billy W.↗
NASA NTRS1991

Aerothermodynamic environments of aerobraking vehicles for manned Mars missions

The aerothermodynamic environments of manned spacraft aerobraking in the Martian and earth atmospheres are evaluated. Thermal performance of aerobrake concepts are examined for current cryogenic-aerobrake and advanced propulsion missions entailing three different modes of aerobraking: (1) aerocapture into an orbit about Mars, (2) descent and landing at Mars, and (3) Mars return direct entry at earth. Analyses for these vehicles and modes included both radiative and convective heating, where radiative heating is shown to be a significant portion of the total stagnation point heating induced on the vehicle. A comprehensive parametric study of the effects of ballistic coefficient, nose radius, entry velocity, and L/D on stagnation point heating is described. Optimal nose radii for ranges of ballistic coefficient and entry velocity are determined. The peak heating rates are shown to be 83 W/sq cm and 90 W/sq cm for a low and high L/D Mars transfer vehicle configuration, respectively. Heating profiles for these vehicles using boundary layer techniques show that a high L/D shape will result in a smaller high-temperature region provided the flow is laminar. An examination of a crew return vehicle for a Mars return direct entry trajectory shows that the thermal protection for this aerobrake will require an ablative material for heat rejection due to the large heating rates (about 1 kW/sq cm).

Ledoux, Stephen T.↗
NASA NTRS1990

High and low thrust mission analysis for a Mars exploration program

The purpose of the study is to identify limits, trends, and sensitivities of Mars Transportation System performance over several Mars mission opportunities. Two Mars Transfer Vehicle (MTV) configurations utilizing different propulsion systems (Chemical/Aerobrake and NEP - Nuclear Electric Propulsion) are outlined. The trades involved in comparing two MTS candidate designs are assessed. Mission analysis for mission opportunities beginning in around 2010 and continuing past 2030 is performed, and a Mars mission model is covered, along with orbit selection and NEP and Chemical/Aerobrake performance. The results of several sensitivity studies are given in order to allow for contingency planning in design and performance. It is concluded that the low-thrust system perform best, its vehicle mass is lower and its trip times are more stable.

Shepard, Kyle M.↗