Search NASA⌕ Search

SEARCH · Search NASA

Results for “Measurement noise”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

A Study of Acoustic Reflections in Full-Scale Rotor Low Frequency Noise Measurements Acquired in Wind Tunnels

Difficulties in obtaining full-scale rotor low frequency noise measurements in wind tunnels are addressed via residual sound reflections due to non-ideal anechoic wall treatments. Examples illustrated with the Boeing-SMART rotor test in the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel facility demonstrated that these reflections introduced distortions in the measured acoustic time histories that are not representative of free-field rotor noise radiation. A simplified reflection analysis, based on the method of images, is used to examine the sound measurement quality in such "less-than-anechoic" environment. Predictions of reflection-adjusted acoustic time histories are qualitatively shown to account for some of the spurious fluctuations observed in wind tunnel noise measurements

Barbely, Natasha L.↗
NASA NTRS1975

Experimental clean combustor program noise measurement addendum, phase 1

The test results of combustor noise measurements taken with waveguide probes are presented. Waveguide probes were shown to be a viable measurement technique for determining high sound pressure level broadband noise. A total of six full-scale annular combustors were tested and included the three advanced combustor designs: swirl-can, radial/axial, and double annular.

Emmerling, J. J.↗
NASA NTRS1972

Noise measurements of model jet-augmented lift systems

Noise measurements were obtained on models of jet-augmented lift systems which are currently being considered for use on proposed short takeoff and landing vehicles. These configurations included a conventional internally blown flap, an augmenter wing, an externally blown flap, and modifications of these basic concepts. The tests were conducted in the Langley anechoic noise facility at zero forward speed with cold air jets. The conventional internally blown flap exhibited lower noise levels than the augmenter wing and the externally blown flap at the same pressure ratios, being of the order of 8 dB or more at the lowest pressure ratio and of the order of 20 dB at the highest pressure ratio of the tests. The data also indicated that for the conventional internally blown flap, there may be an optimum gap size (other than zero) between the turning lip and the flap leading edge from the standpoint of minimum noise generation or admittance. Increasing the trailing-edge thickness of the plain internally blown flap produced no appreciable change in the overall sound pressure level or frequency spectral content in the range of the tests. The data indicated that at a position on the ground directly under the jet exit, the externally blown flap and the augmeter-wing overall noise levels are comparable to each other throughout the pressure range of the tests.

Gibson, F. W.↗
NASA NTRS1990

Olympus receiver evaluation and phase noise measurements

A set of measurements performed by the Michigan Tech Sensing and Signal Processing Group on the analog receiver built by the Virginia Polytechnic Institute (VPI) and the Jet Propulsion Laboratory (JPL) for propagation measurements using the Olympus Satellite is described. Measurements of local oscillator (LO) phase noise were performed for all of the LOs supplied by JPL. In order to obtain the most useful set of measurements, LO phase noise measurements were made using the complete VPI receiver front end. This set of measurements demonstrates the performance of the receiver from the Radio Frequency (RF) input through the high Intermediate Frequency (IF) output. Three different measurements were made: LO phase noise with DC on the voltage controlled crystal oscillator (VCXO) port; LO phase noise with the 11.381 GHz LO locked to the reference signal generator; and a reference measurement with the JPL LOs out of the system.

Campbell, Richard L.↗
NASA NTRS1987

Adaptive control for flexible space structures with measurement noise

Simulation results are presented to address the problem of measurement noise in the design of adaptive controllers for large flexible space structures. In order to reduce the unrealistically high overall control demand resulting from the presence of leakage terms, a method has been developed for the introduction of noise filters into the adaptive controller while at the same time ensuring the global stability of the adaptive algorithm. A branch filter allows filtering of the output error without introducing phase lag into the adaptive loop. The technique is demonstrated in the simulation of an adaptive payload articulation control for a Space Station model.

Bayard, David S.↗
NASA NTRS1961

Near-Field and Far-Field Noise Measurements for a Blowdown-Wind-Tunnel Supersonic Exhaust Jet having about 475,000 Pounds of Thrust

Near-field and far-field noise surveys were made of the supersonic The exhaust jet of the Langley 9- by 6-foot thermal structures tunnel. The jet had a thrust rating of approximately 475,000 pounds. The sound power radiated was found to be about 3.6 x 10(exp 6) watts, and on an acoustical-mechanical efficiency basis this value is in reasonable agreement with data for smaller supersonic jets and for rocket engines of other investigations. Octave-band analyses of the near-field noise show that the maximum sound pressure levels in the low-frequency bands are greatest downstream, whereas maximum sound pressure levels in the high-frequency bands were greatest near the jet exit. A comparison of near-field noise measurements is made with data previously obtained for rocket engines. Noise survey measurements of the original jet are compared with similar data obtained after the addition of a 97-foot-long exit diffuser section, and an example of the application of this facility to the problem of acoustic environmental testing of a large space capsule is cited.

Mayes, William H.↗
NASA NTRS1973

Results of the flight noise measurement program using a standard and modified SH-3A helicopter

A field noise measurement program has been conducted using both a standard SH-3A helicopter and an SH-3A helicopter modified to reduce external noise levels. Modifications included reducing rotor speed, increasing the number of rotor blades, modifying the blade-tip shapes, and acoustically treating the engine air intakes and exhaust. The purpose of this study was to document the noise characteristics recorded on the ground of each helicopter during flyby, hover, landing, and take-off operations. Based on an analysis of the measured results, the average of the overhead, overall, ontrack noise levels was approximately 4 db lower for the modified helicopter than for the standard helicopter. The improved in-flight noise characteristics, and associated small footprint areas and time durations, were judged to be mainly due to tail-rotor noise reductions. The noise reductions were obtained at the expense of required power increases at airspeeds greater than 70 knots for the modified helicopter.

Pegg, R. J.↗
NASA NTRS1980

Landing approach airframe noise measurements and analysis

Flyover measurements of the airframe noise produced by the AeroCommander, JetStar, CV-990, and B-747 airplanes are presented for various landing approach configurations. Empirical and semiempirical techniques are presented to correlate the measured airframe noise with airplane design and aerodynamic parameters. Airframe noise for the jet-powered airplanes in the clean configuration (flaps and gear retracted) was found to be adequately represented by a function of airplane weight and the fifth power of airspeed. Results show the airframe noise for all four aircraft in the landing configuration (flaps extended and gear down) also varied with the fifth power of airspeed, but this noise level could not be represented by the addition of a constant to the equation for clean-configuration airframe noise.

Lasagna, P. L.↗
NASA NTRS1974

Vibration and noise measuring instruments built in the RSR

The demands placed upon vibration and noise measuring instruments are discussed. The instruments that are now being manufactured in the RSR are described, as well as those that are being made ready for manufacture, namely: the VP-3 portable vibrometer, the N2103 precision electronic vibrometer, the N2103 B sonometric preamplifier, as well as vibration transducers of the electrodynamic and piezoelectric types.

Georgescu, I.↗
NASA NTRS1991

Detailed noise measurements on the SR-7A propeller: Tone behavior with helical tip Mach number

Detailed noise measurements were taken on the SR-7A propeller to investigate the behavior of the noise with helical tip Mach number and then to level off as Mach number was increased further. This behavior was further investigated by obtaining detailed pressure-time histories of data. The pressure-time histories indicate that a portion of the primary pressure pulse is progressively cancelled by a secondary pulse which results in the noise leveling off as the helical tip Mach number is increased. This second pulse appears to originate on the same blade as the primary pulse and is in some way connected to the blade itself. This leaves open the possibility of redesigning the blade to improve the cancellation; thereby, the propeller noise is reduced.

Dittmar, James H.↗