Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mg alloys”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Interfacial reaction during friction stir assisted scribe welding of immiscible Fe and Mg alloy system

We report on interfacial characteristics and chemistry of bonded Mg-Fe interfaces welded using friction stir assisted scribe technique (FaST). Two pairs of dissimilar joints: (AZ31-DP590) and (Pure Mg-DP590) were studied to shed light on joining mechanisms responsible for bonding of “immiscible” pairs of Mg and Fe. We present first direct experimental evidence of presence of oxide layer, Al segregation by atom probe tomography and nano steel grains close to interface by transmission electron microscopy study.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Numerical investigation of micro-galvanic corrosion in Mg alloys: Role of the cathodic intermetallic phase size and spatial distributions

Magnesium alloys are of increasing interest in structural applications due to their low-density, moderate specific strength and stiffness, recyclability, and high damping among other properties. However, the wide-scale applicability of magnesium alloys in structural applications has been limited due to many factors including its poor corrosion resistance. In this work, a numerical investigation to simulate the micro-galvanic corrosion behavior was performed to examine the influence of size and distribution of cathodic intermetallic phase (ß-Mg17Al12) in a Mg matrix. The ratio of cathodic to anodic surface area was kept constant in each simulation condition to understand the effect of size and spacing distributions. In general, fragmentation of a larger intermetallic particle into smaller ones was found to enhance the localized current density. However, the uniform distribution of this small intermetallic phase throughout the matrix was found to reduce the overall dissolution current density and hence, pitting corrosion severity.

Beura, Vikrant↗
DOE OSTI2020

Modeling of the thermo-mechanical response and texture evolution of WE43 Mg alloy in the dynamic recrystallization regime using a viscoplastic self-consistent formulation

This paper presents a microstructure sensitive model for predicting mechanical response and texture evolution of metals in the dynamic recrystallization regime. A recently proposed viscoplastic self-consistent (VPSC) formulation for the prediction of recrystallization driven by strain energy and intragranular misorientation is extended to hexagonal close-packed (hcp) metals. The model is applied to the dynamic recrystallization of magnesium alloy WE43 at different temperatures and strain rates. Model predictions in terms of stress-strain response and texture evolution are compared to the experimental measurements and acceptable agreement is achieved. According to the model predictions, superplastic behavior of nuclei was found to be the dominant softening mechanism at high temperatures and low strain rates. High concentration of precipitates at the grain boundaries and presence of alloying elements are the likely causes of low boundary mobility, resulting in nucleation dominated dynamic recrystallization. Relatively strong basal compression textures indicate dominant activity of basal slip, which can be achieved only through large difference in slip resistance between soft basal and hard prismatic and pyramidal modes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Melt-Pool Dynamics and Microstructure of Mg Alloy WE43 under Laser Powder Bed Fusion Additive Manufacturing Conditions

Magnesium-based alloy WE43 is a state-of-the-art bioresorbable metallic implant material. There is a need for implants with both complex geometries to match the mechanical properties of bone and refined microstructure for controlled resorption. Additive manufacturing (AM) using laser powder bed fusion (LPBF) presents a viable fabrication method for implant applications, as it offers near-net-shape geometrical control, allows for geometry customization based on an individual patient, and fast cooling rates to achieve a refined microstructure. In this study, the laser–alloy interaction is investigated over a range of LPBF-relevant processing conditions to reveal melt-pool dynamics, pore formation, and the microstructure of laser-melted WE43. In situ X-ray imaging reveals distinct laser-induced vapor depression morphology regimes, with minimal pore formation at laser-scan speeds greater than 500 mm/s. Optical and electron microscopy of cross-sectioned laser tracks reveal three distinct microstructural regimes that can be controlled by adjusting laser-scan parameters: columnar, dendritic, and banded microstructures. These regimes are consistent with those predicted by the analytic solidification theory for conduction-mode welding, but not for keyhole-mode tracks. The results provide insight into the fundamental laser–material interactions of the WE43 alloy under AM-processing conditions and are critical for the successful implementation of LPBF-produced WE43 parts in biomedical applications.

36 MATERIALS SCIENCE↗
NASA NTRS1988

Dispersion strengthening of precipitation hardened Al-Cu-Mg alloys prepared by rapid solidification and mechanical alloying

Several Al-4Cu-1Mg-1.5Fe-0.75Ce alloys have been processed from either rapidly solidified or mechanically alloyed powder using various vacuum degassing parameters and consolidation techniques. Strengthening by the fine subgrains, grains, and the dispersoids individually or in combination is more effective when the alloys contain shearable precipitates; consequently, the strength of the alloys is higher in the naturally aged rather than the artificially aged condition. The strengths of the mechanically alloyed variants are greater than those produced from prealloyed powder. Properties and microstructural features of these dispersion strengthened alloys are discussed in regards to their processing histories.

Gilman, P. S.↗
NASA NTRS1991

Natural aging and reversion behavior of Al-Cu-Li-Ag-Mg alloy Weldalite (tm) 049

This study was initiated to understand the natural aging and reversion behavior of Weldalite (trademark) 049 in tempers without cold work. Of particular interest are: (1) the microstructural basis for the high strength in the T4 condition; (2) an explanation of the reversion phenomenon; and (3) the effect of re-aging at room temperature after a reversion treatment. Mechanical properties were measured and transmission electron microscopy (TEM) analysis performed at various stages of microstructural development during aging, reversion, and subsequent re-aging.

Gayle, Frank W.↗
NASA NTRS1990

The roles of Zr and Mn in processing and superplasticity of Al-Mg alloys

Processing studies have been conducted on two alloys, of nominal compositions Al-10Mg-0.1Zr or Al-10Mg-0.5Mn, in order to clarify the role of the dispersoid forming Zr or Mn additions. Mechanical property data reveal that the Mn-containing alloy has a lower maximum elongation but exhibits superplastic response over a broader range of temperature. Microstructural investigations and texture analyses were utilized to assess the effect of the presence of Al8Mg5 precipitates in combination with either Al3Zr or Al6Mn dispersoid particles during isothermal rolling at 300 C and subsequent tensile deformation at temperatures from 200-425 C.

Mcnelley, Terry R.↗
DOE OSTI2024

Effect of Si impurities on microstructure and tensile properties of a cast Al-Mg-Fe alloy

Al-Mg alloys are attractive for structural castings owing to their superior strength and ductility in the as-cast state. However, given the tight tolerance for impurities, Al-Mg alloys produced from secondary sources still face multiple challenges. Here, we report the effect of increased Si impurity (0.05–1.6 wt%), which is commonly found in secondary Al sources, on microstructure and tensile properties of a cast Al-4.3Mg-1.6Fe (wt%) alloy, commercially referred to as Castaduct-42 alloy. Microstructural characterization revealed that Si addition increased the volume fraction, size, and aspect ratio of primary Al13Fe4 intermetallic particles as well as the volume fraction of other binary and ternary eutectic phases. Tensile testing results demonstrated that increasing Si impurities from 0.05 to 1.6 wt% reduced ductility from 14.3 ± 1.4 % to 2.2 ± 1.0 %. A particle cracking damage accumulation model coupled with failure analysis indicated primary Al13Fe4 intermetallic particles to be the major contributing factor to the deterioration in ductility with increasing Si content. Additionally, the stabilizing effect of Si on primary Al 13 Fe 4 was inconsistent with the CALPHAD calculation results based on existing CALPHAD databases which predict a slightly decreasing primary Al13Fe4 phase fraction with increasing Si concentration. This work provides new insights into the phase stability and mechanical behavior of the lesser studied Al-Mg-Fe-Si alloy system that will contribute to the development of sustainable cast Al-Mg based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Comparative Study of Zinc Cold-Spray Coating and Pre-treatments for Magnesium Alloys

Magnesium (Mg) alloys are appealing for automotive lightweighting owing to their high specific strength. However, their susceptibility to corrosion in harsh environments remains a major challenge. Conventional industrial pre-treatment coatings, including zinc phosphate, chromate conversion, and non-chromate conversion, often exhibit discontinuities and microcracks, leading to localized corrosion near fasteners and parting lines. Here, this study investigates cold-sprayed zinc (Zn) coatings as a novel pre-treatment alternative for high-pressure die cast (HPDC) AZ91 Mg alloys, demonstrating significant improvements in wear and corrosion performance. Cold spray produces uniform and robust coatings, reducing wear rate by over 50% and reducing corrosion rate by over 99.3%, as measured by evolved hydrogen release, compared to traditional pre-treatments. Multimodal corrosion testing reveals that Zn cold-spray coatings form a protective layer during exposure, minimizing general and filiform corrosion, and exhibiting corrosion potential (E corr ) that is nobler by ~ 400 mV than the surfaces of both pre-treated and uncoated AZ91. Scalability of cold spray for selective application around multimaterial joints further strengthens their industrial viability. This work establishes Zn cold-spray coatings as highly effective pre-treatment solutions for the advancement of corrosion resistant Mg alloy components in automotive applications.

multimodal corrosion↗
DOE OSTI2026

Investigation of the Surface Chemistry of Magnesium and Magnesium Alloy Powders

Magnesium (Mg) and Mg alloy powders are generally difficult to sinter at atmospheric pressure in inert atmospheres purportedly due to the presence of powder particle surface oxide layers. To better understand sintering of Mg and Mg alloy powders, x-ray photoelectron spectroscopy (XPS) was performed to characterize the surface chemistry of gas atomized pure Mg and Mg alloys AZ91D and WE43 powders. These results are used to quantitatively determine the surface chemistry of these powders. Additionally, equilibrium thermodynamic modeling of these Mg/Mg alloys materials exposed to oxygen down to part per billion concentrations are presented for relative comparison to experimental XPS results. Analysis of these results are intended to improve sintering of Mg and Mg alloy powder materials through more quantitative knowledge of powder surface chemistry.

25 ENERGY STORAGE↗