SEARCH · Search NASA
Results for “Microstructures”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Comparing non-destructive 3D X-ray computed tomography with destructive optical microscopy for microstructural characterization of fiber reinforced composites
Due to their lightweight, relatively high stiffness properties, and formability into complex shapes, discontinuous fiber composites are advantageous for producing small and medium size components. Improved characterization techniques and post-processing methodologies are required for more reliable quantification of the microstructure and defect distributions in these materials, in order to employ model-based approaches to assess their structural integrity. This work compares a non-destructive X-ray approach with a destructive optical microscopy approach for characterizing the microstructural attributes, specifically the fiber volume fraction, porosity volume fraction, fiber orientation distribution, and fiber length distribution of discontinuous glass fibers in a polypropylene matrix. Additionally, a method for destructively determining the ambiguous components of the orientation tensor (related to the sign ambiguity of the out-of-plane angle in a destructive cross-sectional cut of a fiber) over a large surface area is included. It was found that fiber volume fraction and average fiber aspect ratio matched well, while fiber orientation and porosity detection had small but notable differences. The differences in the detection capabilities of each technique are quantified and discussed shedding light on the specific advantages and disadvantages of each approach, and enabling engineers to quantify uncertainty in their microstructural characterization measurements especially as they relate to model based structural integrity activities.
Influence of processing on the microstructure and mechanical properties of 14YWT
The investigation of the mechanical alloying (MA) conditions for producing the advanced oxide dispersion strengthened (ODS) 14YWT ferritic alloy led to significant improvements in balancing the strength, ductility and fracture toughness properties while still maintaining the salient microstructural features consisting of ultra-fine grains and high concentration of Y-, Ti- and O-enriched nanoclusters. The implemented changes to the processing conditions included reducing the contamination of the powder during ball milling, applying a pre-extrusion annealing treatment on the ball milled powder and exploring different extrusion temperatures at 850 C (SM170 heat), 1000 C (SM185) and 1150 C (SM200). The microstructural studies of the three 14YWT heats showed similarities in the dispersion of nanoclusters and sub-micron size grains, indicating the microstructure was insensitive to the different extrusion conditions. Compared to past 14YWT heats, the three new heats showed lower strength, but higher ductility levels between 25 and 800 C and significantly higher fracture toughness values between 25 C and 700 C. The lower contamination levels of O, C and N achieved with improved ball milling conditions plus the slightly larger grain size were identified as important factors for improving the balance in mechanical properties of the three heats of 14YWT.
Mesoscale Modeling of the Effects of Accelerated Burnup on UO2 Microstructural Evolution
Accelerating the nuclear fuel qualification process will rely on some combination of advanced modeling and simulation techniques with accelerated irradiation testing and separate effects experiments to enable the development of new fuel concepts in a shorter time frame. One of the key challenges to successfully leveraging accelerated irradiation tests will be understanding the artifacts that may be introduced with accelerated accumulation of dose and/or burnup. This work presents phase field (MARMOT) simulations of the evolution of representative 2D UO2 microstructures up to 40 MWd/kgU. Simulations were performed under both commercial light water reactor fuel conditions as well as those that would be expected for highly accelerated (~10x) burnup conditions similar to those used in the MiniFuel irradiations in Oak Ridge National Laboratory’s High Flux Isotope Reactor. The phase field model was coupled with a discrete nucleation algorithm to model re- structuring at high burnup. The effect of the different fission rates in both microstructures was investigated at two temperatures: 650?C and 800?C. The lower temperature simulations both showed an onset of restructuring at nearly 60 MWd/kgU. More extensive restructuring was obtained in the MiniFuel microstructure compared with that of the PWR fuel. At 800?C, no restructuring was obtained as a result of the thermally activated diffusion of Xe atoms and U vacancies to fission gas bubbles, which reduces the nucleation driving force. These results highlight the importance of using modeling and simulation tools to inform the environmental conditions during targeted accelerated irradiation tests to extract the most useful fuel performance data.
Microstructure Scale Lithium-Ion Battery Modeling, Part IV: The Representativity of Microstructure Parameters and Electrochemical Response
Lithium-ion battery electrochemical models require an accurate description of the electrodes microstructures to be predictive, that can be achieved through nanoscale imaging. Such observations are however limited by their field of view (FOV), as they provide only a subset of the whole electrode volume that does not necessarily represent the whole electrode microstructure heterogeneity, and therefore can bias the analysis. A representativity analysis has been performed on the microstructure parameters and, in a novel way, on the full cell electrochemical response to evaluate the predictions representativeness, and thus relevance, of a microstructure scale electrochemical model. The microstructure parameter deviation propagations to the electrochemical response have been quantified for different charge rates. This defines a threshold for the microstructure parameters FOV for a desired maximum deviation of the electrochemical response. Electrochemical model shows cell representative section areas are increasing with C-rate, due to higher in-plane heterogeneities, indicating larger FOVs are required specifically for fast charge modeling. Representativity analysis determines a cell FOV of 144.4 × 154.4 μm 2 is large enough to establish a convergence on the representative section areas for low-intermediate C-rate (≤2.5 C), therefore positively concludes on the model representativeness for these rates, but is not large enough to conclude for higher rates.
Implications of doping on microstructure, processing, and thermoelectric performance: The case of PbSe
Abstract In this work, we highlight the often-overlooked effects of doping on the microstructure and performance of bulk thermoelectric materials to offer a broader perspective on how dopants interact with their parent material. Using PbSe doped with Na, Ag, and K as a model material system, we combine original computational, experimental, and microscopy data with established trends in material behavior, to provide an in-depth discussion of the relationship between dopants, processing, and microstructure, and their effects on thermoelectric efficiency and thermal stability. Notable observations include differences in the microstructure and mass loss of thermally treated samples of Na- and Ag-doped PbSe, as well as findings that Na and K cations exist predominantly as substitutional point defects while Ag also occupies interstitial sites and exhibits lower solubility. We discuss how these differences in point defect populations are known to affect a dopants’ ability to alter carrier concentration and how they may affect the mechanical properties of PbSe during processing. Graphic Abstract
Reification of latent microstructures: On supervised unsupervised and semi-supervised deep learning applications for microstructures in materials informatics
Machine learning (ML), including deep learning (DL), has become increasingly popular in the last few years due to its continually outstanding performance. In this context, we apply machine learning techniques to "learn" the microstructure using both supervised and unsupervised DL techniques. In particular, we focus (1) on the localization problem bridging (micro)structure (localized) property using supervised DL and (2) on the microstructure reconstruction problem in latent space using unsupervised DL. The goal of supervised and semi-supervised DL is to replace crystal plasticity finite element model (CPFEM) that maps from (micro)structure (localized) property, and implicitly the (micro)structure (homogenized) property relationships, while the goal of unsupervised DL is (1) to represent high-dimensional microstructure images in a non-linear low-dimensional manifold, and (2) to discover a way to interpolate microstructures via latent space associating with latent microstructure variables. At the heart of this report is the applications of several common DL architectures, including convolutional neural networks (CNN), autoencoder (AE), and generative adversarial network (GAN), to multiple microstructure datasets, and the quest of neural architecture search for optimal DL architectures.
The microstructure of near-equiatomic B2/f.c.c. FeNiMnAl alloys
A microstructural analysis of two FeNiMnAl alloys, Fe{sub 30}Ni{sub 20}Mn{sub 30}Al{sub 20} and Fe{sub 25}Ni{sub 25}Mn{sub 30}Al{sub 20}, was performed by a combination of atom probe tomography and transmission electron microscopy techniques. Although the microstructures of both alloys, which consist of alternating platelets aligned along < 100> of the B2-ordered phase, are similar to B2/b.c.c. two-phase alloys previously observed in the FeNiMnAl system, the two phases present in the current alloys are B2-ordered and f.c.c., with the latter phase being heavily twinned. Very fine ({approx} 5 nm) precipitates, whose chemistry was similar to that of the f.c.c. (Fe, Mn)-rich phase, were found within the B2 (Ni, Al)-rich phase in both alloys. - Highlights: {yields} The microstructures of the novel alloys Fe{sub 30}Ni{sub 20}Mn{sub 30}Al{sub 20} and Fe{sub 25}Ni{sub 25}Mn{sub 30}Al{sub 20} were characterized. {yields} Atom probe tomography and transmission electron microscopy were used in the study. {yields} A < 100>-aligned B2-ordered phase and heavily-twinned f.c.c. phase were present. {yields} Very fine (Fe, Mn)-rich precipitates were found within the B2 (Ni, Al)-rich phase.
Comparison of SOFC Cathode Microstructure Quantified using X-ray Nanotomography and Focused Ioni Beam-scanning Electron Microscopy
X-ray nanotomography and focused ion beam scanning electron microscopy (FIB-SEM) have been applied to investigate the complex 3D microstructure of solid oxide fuel cell (SOFC) electrodes at spatial resolutions of 45 nm and below. The application of near edge differential absorption for x-ray nanotomography and energy selected backscatter detection for FIB-SEM enable elemental mapping within the microstructure. Using these methods, non-destructive 3D x-ray imaging and FIB-SEM serial sectioning have been applied to compare three-dimensional elemental mapping of the LSM, YSZ, and pore phases in the SOFC cathode microstructure. The microstructural characterization of an SOFC cathode is reported based on these measurements. The results presented demonstrate the viability of x-ray nanotomography as a quantitative characterization technique and provide key insights into the SOFC cathode microstructure.
Effect of stress evolution on microstructural behavior in U-Mo/Al dispersion fuel [Effect of stress on microstructural evolution in U-Mo/Al dispersion fuel]
U-Mo/Al dispersion fuel irradiated to high burnup at high power (high fission rate) exhibited microstructural changes such as deformation of the fuel particles, pore growth, and rupture of the Al matrix. The driving force for these microstructural changes was meat swelling caused by a combination of fuel particle swelling and interaction layer growth. Five miniplates with well-recorded fabrication data and irradiation conditions were selected, and their PIE data was analyzed. ABAQUS finite element analysis (FEA) was utilized to simulate the microstructural evolution of the plates. Using the simulation results shear stress, effective stress and hydrostatic stress exerted on both the fuel particles and the Al matrix were determined. The effects of fabrication and irradiation variables on stress-induced microstructural evolutions, such as pore growth in the interaction layers and Al matrix rupture, were investigated. The observed microstructural changes were consistent with the calculated stress distribution in the meat.
The influence of steel microstructure and inclusion characteristics on the formation of premature bearing failures with microstructural alterations
The formation of premature cracking damage associated with local microstructural alterations, commonly referred to as "white etching cracks" (WECs) has led to unpredictable bearing failures in numerous industrial applications. WECs are known to occur in the field independent of material characteristics such as heat treatment, predominant microstructure and surface coatings, as well as lubricant characteristics such as additive packages and viscosity. However, WECs have proven difficult to recreate at a benchtop scale; to date, no benchtop test has been reported to recreate WECs using commercially available field lubricants. The present work intends to identify key differences between the microstructure of field bearings and the microstructure of benchtop samples, focusing on the characteristics of the inclusions contained in both steels. Synchrotron scale X-ray tomography revealed that AISI 52100 steel used in industrial scale field bearings contained a drastically different inclusion microstructure then the AISI 52100 steels used in standard benchtop test specimens. Additionally, the authors were able to form WECs in test samples manufactured out of the steel of a field bearing using fully formulated field lubricants; a finding which has not yet been reported in open literature.
Microstructure and mechanical properties of heat-treated and neutron irradiated TRISO-ZrC coatings
Not Available
Mechanical property degradation and microstructural evolution of cast austenitic stainless steels under short-term thermal aging
Mechanical testing and microstructural characterization were performed on short-term thermally aged cast austenitic stainless steels (CASS) to understand the severity and mechanisms of thermal-aging degradation experienced during extended operation of light water reactor (LWR) coolant systems. Four CASS materials – CF3, CF3M, CF8, and CF8M – were thermally aged for 1500 hours at 290 °C, 330 °C, 360 °C, and 400 °C. All four alloys experienced insignificant change in strength and ductility properties but a significant reduction in absorbed impact energy. The primary microstructural and compositional changes during thermal aging were spinodal decomposition of the δ-ferrite into α/ α`, precipitation of G-phase in the δ-ferrite, segregation of solute to the austenite/ ferrite interphase boundary, and growth of M23C6 carbides on the austenite/ferrite interphase boundary. These changes were shown to be highly dependent on chemical composition, particularly the concentration of C and Mo, and aging temperature. A comprehensive model is being developed to correlate the microstructural evolution with mechanical behavior and simulation for predictive evaluations of LWR coolant system components.
Microstructure Scale Lithium-Ion Battery Modeling: Part III. When and Where Lithium Plating Occurs and its Correlation with the Electrode Microstructure
Li-ion battery performance and degradation are closely related to the cell’s underlying electrode microstructure. Electrode microstructures are typically characterized with volume-averaged properties that neglect the impact of local heterogeneities. However, local heterogeneities create hot spots that can trigger degradation onset. Herein, a microstructure scale electrochemical model is used to investigate the impact of microstructure heterogeneity on lithium plating. The model predicts lithium plating is not uniform, even when considering a relatively small portion of the electrode (a cross-sectional area of 154×144 µm 2 ), preferring to plate on larger particles as compared to smaller particles. While local heterogeneities control where plating occurs, the model predicts that volume-averaged properties control when plating occurs. Additionally, the model predicts that the active material specific surface area has a linear relationship with the plating onset. However, the linear relationship between increased active material surface area and delayed plating response appears to be sensitive to the microstructure feature used to increase the active interface area. Here, a comparative case-study is explored where the specific surface area is increased by either reducing the active material particle diameter, adding open-porosity cracks, or increasing the active material surface roughness. The model predicts that increasing the specific surface area by reducing the active material particle diameter is the most effective strategy for delaying lithium plating. At 6C, reducing particle size is shown to be 3 and 20 times more effective than, respectively, adding open-porosity cracks and increasing surface roughness. A dual-layer electrode architecture combining gradations both for average properties and uniformities is eventually proposed to improve homogeneous material utilization and reduce degradation at high charge rates.
Microstructural effects in the simulation of creep of concrete
The influence of the microstructure on the visco-elastic properties of concrete is investigated using finite element simulations at the meso-scale. We first derive a constitutive law for the creep of the cement paste which accounts for both recoverable and permanent deformations, as well as the influence of temperature and internal relative humidity. The model is calibrated on a set of experiments at the cement paste scale, and then validated after upscaling to the concrete scale. The model is then applied to study the influence of the microstructure on the macroscopic creep of concrete. We show that materials with finer particles exhibit less creep, and that the anisotropy of creep can be explained with the shape and orientation of the aggregates. Furthermore, the acceleration of the stress relaxation in the presence of damage is explained by the micro-mechanical interaction between the aggregates, the cement paste, and the micro-cracks.
Quantitative Microstructure Characterization of a NMC Electrode
Performance of lithium-ion batteries (LIBs) is strongly influenced by the porous microstructure of their electrodes. In this work, 3D microstructures of calendared and un-calendared positive electrode LiNi1/3Mn1/3Co1/3O2 (NMC) have been investigated in order to extract relevant properties useful for battery modeling. Transport (volume fraction, connectivity, particle size and tortuosity) and electrochemical (specific surface area) properties have been calculated for the pore and the active material. Special attention has been paid to determine the size of the so-called representative volume element (RVE) required to be statistically representative of the heterogeneous medium. Several parameters have been calculated using a panel of different numerical methods in order to compare their results. Besides, the image level of detail has been evaluated (using original criteria based upon edge detection) to assess the overall data quality available for the study.
Three-dimensional microstructural changes in the Ni–YSZ solid oxide fuel cell anode during operation
Explore the source record for details and available documents.
Processing effects on microstructure in Er and ErD 2 thin-films
Erbium metal thin-films have been deposited on molybdenum-on-silicon substrates and then converted to erbium dideuteride (ErD 2 ). Here in this work, we study the effects of deposition temperature (≈300 or 723 K) and deposition rate (1 or 20 nm/s) upon the initial Er metal microstructure and subsequent ErD 2 microstructure. We find that low deposition temperature and low deposition rate lead to small Er metal grain sizes, and high deposition temperature and deposition rate led to larger Er metal grain sizes, consistent with published models of metal thin-film growth. ErD 2 grain sizes are strongly influenced by the prior-metal grain size, with small metal grains leading to large ErD 2 grains. A novel sample preparation technique for electron backscatter diffraction of air-sensitive ErD 2 was developed, and allowed the quantitative measurement of ErD 2 grain size and crystallographic texture. Finer-grained ErD 2 showed a strong (1 1 1) fiber texture, whereas larger grained ErD 2 had only weak texture. Finally, we hypothesize that this inverse correlation may arise from improved hydrogen diffusion kinetics in the more defective fine-grained metal structure or due to improved nucleation in the textured large-grain Er.