Search NASA⌕ Search

SEARCH · Search NASA

Results for “Molten salt”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Electrochemistry of the NaI-AlBr 3 Molten Salt System: A Redox-Active, Low-Temperature Molten Salt Electrolyte

NaI-AlBr 3 is a very appealing low melting temperature (<100 °C), salt system for use as an electrochemically-active electrolyte. This system was investigated for its electrochemical and physical properties with focus to energy storage considerations. A simple phase diagram was generated; at >100 °C, lower NaI concentrations had two partially miscible liquid phases, while higher NaI concentrations had solid particles. Considering the fully molten regime, electrical conductivities were evaluated over 5–25 mol% NaI and 110 °C–140 °C. Conductivities of 6.8–38.9 mS cm −1 were observed, increasing with temperature and NaI concentration. Effective diffusion coefficients of the I − /I 3 − redox species were found to decrease with both increasing NaI concentration and increasing applied potential. Regardless, oxidation current density at 3.6 V vs Na/Na + was observed to increase with increasing NaI concentration over 5–25 mol%. Finally, the critical interface between the molten salt electrolyte and electrode materials was found to significantly affect reaction kinetics. When carbon was used instead of tungsten, an adsorbed species, most likely I 2 , blocked surface sites and significantly decreased current densities at high potentials. This study shows the NaI-AlBr 3 system offers an attractive, low-temperature molten salt electrolyte that could be useful to many applied systems, though composition and electrode material must be considered.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Rapid-charging aluminium-sulfur batteries operated at 85 °C with a quaternary molten salt electrolyte

Molten salt aluminum-sulfur batteries are based exclusively on resourcefully sustainable materials, and are promising for large-scale energy storage owed to their high-rate capability and moderate energy density; but the operating temperature is still high, prohibiting their applications. Here we report a rapid-charging aluminium-sulfur battery operated at a sub-water-boiling temperature of 85°C with a tamed quaternary molten salt electrolyte. The quaternary alkali chloroaluminate melt – possessing abundant electrochemically active high-order Al-Cl clusters and yet exhibiting a low melting point – facilitates fast Al 3+ desolvation. A nitrogen-functionalized porous carbon further mediates the sulfur reaction, enabling the battery with rapid-charging capability and excellent cycling stability with 85.4% capacity retention over 1400 cycles at a charging rate of 1 C. Importantly, we demonstrate that the asymmetric sulfur reaction mechanism that involves formation of polysulfide intermediates, as revealed by operando X-ray absorption spectroscopy, accounts for the high reaction kinetics at such temperature wherein the thermal management can be greatly simplified by using water as the heating media.

25 ENERGY STORAGE↗
DOE OSTI2025

MOSCATO Development and Integration in Fiscal Year 2025: Implementation of Multiphase, Multiphysics Modeling Capabilities for Molten Salt Systems

MOSCATO (Molten Salt Chemistry and Transport) is a multiphysics code that provides high-fidelity, coupled simulations of fluid flow, heat transfer, mass transfer, chemistry, electrochemical phenomena, and alloy corrosion for molten salt systems. In FY25, significant developments were made to the code package, enhancing its capabilities for modeling all relevant phenomena within operating moltens salt reactors (MSRs). The developments and activities in FY25 included: 1. Implementation of Level-Set methods to enable modeling of single-bubble behavior in molten salts. In FY25, the Level-Set two-phase flow modeling implementation was improved to simulate single bubble behavior with molten salt media. The large density and viscosity ratios between typical gases and molten salt liquids present challenges for these types of numerical solvers. With enhancements to the pressure projection method, MOSCATO’s Level-Set solver was able to be successfully validated to experiments related to helium bubble rise in stagnant molten salt. The simulated bubble rising velocity showed reasonable good agreement with experimental measurements. The bubble shape and dynamics were also visually compared with experimental snapshots, demonstrating a good qualitative match. 2. Generation of mass transfer correlations for multiphase flow systems. To enable calculations of the tritium transport across the interface between gas bubbles and salt, we modeled high- Schmidt-number mass transfer around a sphere across a broad range of Reynolds numbers. The mesh near the sphere surface was highly refined to resolve steep concentration gradients caused by the low diffusion coefficient. Literature-based mass transfer correlations were compared with the numerical results, and modifications were proposed to improve agreement, particularly at higher Schmidt numbers. These mass transfer correlations were subsequently provided to other national laboratories to help enable high quality mass transfer simulations using lower-order solvers under development within the NEAMS program. 3. Preliminary implementation of a bubbly flow solver. To model bubbly flow in molten salt, we implemented a bubbly flow solver for void fractions less than 5%. To do so, an algebraic relative velocity model that assumes small bubbles with rapid momentum equilibration was added to MOSCATO to compute bubble velocities. Preliminary comparisons with experimental data showed reasonable agreement, and further improvements are underway. 4. Generation of mass transfer correlations for MSRE subchannel The Molten-Salt Reactor Experiment (MSRE) was a landmark historical project that demonstrated the feasibility of molten-salt reactor technology. The MSRE campaign also generated a significant body of experimental data and reports that continue to support molten-salt–related research. In this report, the MSRE core subchannel was used as the reference geometry for a mass transfer study performed with MOSCATO. The geometry and computational mesh were adapted from a previous study, providing adequate resolution for the relatively low Reynolds number in this case. Additional mesh refinement was applied to reach higher Schmidt numbers, enabling the derivation of a reliable mass-transfer correlation for the present scenario. 5. Simulations of oxygen ingressions into molten salt. In the previous fiscal year, we initiated a study to simulate oxygen ingression in stagnant salt. As oxygen enters the salt through its surface, it reacts with Ce 3+ to form solid CeO 2 and other reaction products. To more fully capture the complex diffusion-convection-reaction mechanisms, capabilities for modeling natural convection in the salt vessel were added. These were needed as the flow of the ingressed gas induced flow in the salt caused by surface shear and non-isothermal effects. With these updated physics in place, we were able to successfully reproduce the experimental results for the rate of change of CeCl 3 concentrations versus time. 6. Flow corrosion model validation. In FY24, MOSCATO’s corrosion model was validated against static corrosion experiments. In FY25, this work was extended to a flow corrosion experiment, where FLiNaK salt was driven by natural convection, with initial salt impurities to initiate corrosion. Despite uncertainties in parameters such as elemental diffusion coefficients in the alloy and unknown H + concentrations, the simulations achieved good agreement with experimental results, especially in predicting sample mass losses.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

A Facile, One-Step Synthesis for Core–Shell Perovskite Materials via Molten Salt

Core–shell La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF)–La 0.8 Sr 0.2 MnO 3 (LSM) heterostructure crystalline materials have been synthesized in a simple, one-step feeding method via a KNO 3 molten salt solvent. Two-phase perovskite composites can be synthesized in times as short as 10 minutes and is demonstrated for the first time in a molten salt. Further, a combination of X-ray diffraction and S/TEM energy dispersive X-ray spectroscopy has been utilized to confirm the formation of an LSM shell on LSCF cores in all samples when adjusting dwell time, core size, weight ratio between core and shell precursors, and weight ratio of powder to salt. Specifically, decreasing the LSCF core size increases core–shell yield. Smaller cores introduce a greater density of facets on the crystal surface and provide more favorable sites for LSM heterogeneous nucleation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Molten Salt Electrodeposition: Review

Molten salt electrodeposition is the process of producing impressively dense deposits of refractory metals using the electrolysis of molten salts. However, predicting which electrochemical parameters and setup will best control different kinds of deposition (density, homogeneity, etc.) is an ongoing challenge, due to our limited understanding of the properties and mechanisms that drive molten salt electrodeposition. Because these advancements have been made rapidly and in different arenas, it is worth taking the time to stop and assess the progress of the field as a whole. These advancements have increasing relevance for the energy sector, the development of space materials and engineering applications. In this review, we assess four critical facets of this field: (1) how the current understanding of process variables enhances the electrodeposition of various molten salts and the quality of the resulting product; (2) how the electrochemical setup and the process parameters (e.g., cell reactions) are known to impact the electrodeposition of different metal coatings and refractory-metal coatings; (3) the benefits and drawbacks of non-aqueous molten salt electrodeposition, and (4) promising future avenues of research. The aim of this work is to enhance our understanding of the many procedures and variables that have been developed to date. The expectation is that this review will act as a stimulant, motivating scientists to delve further into the investigation of refractory-metal alloys by utilizing molten salt electrodeposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRSDate not supplied

Molten Salt Electrolytes: Computational Analysis of Transport, Electrochemical Properties and Designing New Mixtures

Electric aircraft propulsion has gained a traction over the last decade due to possible high-energy density electrochemistries with reasonable cycle life and identification of non-flammable chemistries that can guarantee much better safety. Commercial Li-ion batteries cannot reach such high capacities because of weight limitations that arise from the widely used intercalation electrodes. Also, use of organic electrolytes make them highly susceptible to fire on exposure to air and humidity. Currently, use of Lithium metal anode along with conversion electrochemistries such as Li-O2 and Li-S are being pursued to achieve such high energy densities. Safer inorganic solid-state electrolytes, recently discovered Water-in-Salt electrolytes, molten salt electrolytes are some of the alternatives being pursued for a safer/non-flammable battery. Of these safer alternatives, molten-salt electrolytes offer some attractive properties: liquid at operating temperatures resulting in better electrode-wetting, stable interface with Li-metal anodes and good ionic conductivity; their only drawback being high operating temperatures. In this talk, we will discuss some of the computational studies, driven via atomistic simulations, of the properties of molten-salt electrolytes including transport mechanism and interface stability. We will also discuss predicting electrochemical properties of these high-temperature electrolytes. Further, we will discuss a thermodynamic approach to predicting new molten-salt eutectics with lower melting points.

Molten Salt Electrolytes↗
DOE OSTI2025

Effect of Soluble Corrosion Products on Electrical Double Layer in LiCl-KCl Molten Salts

Corrosion in molten salts greatly hampers the application for renewable energy applications like molten salt reactors. To develop effective strategies for corrosion mitigation, understanding the interfacial structures and properties such as specific ion adsorption and electrical double layer capacitance are crucial. Using cyclic voltammetry and electrochemical impedance spectroscopy, we systematically studied the interfaces on various model electrodes including W (solid), Bi (liquid), and the stainless steel 316 in LiCl-KCl eutectic molten salts with the addition of corrosion species CrCl 2 and FeCl 2 . Both Cr 2+ and Fe 2+ ions increased electrical double layer capacitance, with Cr 2+ showing specific adsorption behavior and shifting the potential of zero charge, while Fe 2+ had minimal effect on point of zero charge. Two-working electrode measurements revealed increasing open-circuit potential and electrical double layer capacitance during the exposure of stainless steel 316, indicating its progressive corrosion and ion accumulation at the interface. X-ray photoelectron spectroscopy and Raman confirmed Cr enrichment at the interface. This work highlights the strong correlation between electrical double layer behavior and corrosion dynamics in molten salts and suggests electrical double layer capacitance as a sensitive, in situ indicator for corrosion monitoring.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Exploring the speciation of actinide salts in the presence of contaminants related to molten salt reactors

Molten salt reactors (MSR) are up-and-coming Generation IV nuclear reactors with either coolant and/or radioactive fuel in molten salt form. Due to their improved safety, efficiency, affordability and convenient waste processing system, these reactors are considered a superior alternative to conventional ones. However, prior to commercial implementation, it is necessary to have an extensive understanding of the reactions occurring in the MSR. The safety parameters of the MSR are determined by the rheological properties such as density and viscosity of the molten salt and these properties are governed by the local structure of the molten salts. Due to the high operational temperatures of MSR's, corrosion plays an important role. Because of their influence, the container corrosion products become part of the fuel salt matrix. In this work, we are investigating how these corrosion products, e.g., Mo, Ni, Cr, would impact the speciation of the actinide metal centers. For the initial studies, lanthanides are used as a surrogate for actinides. Lanthanide chloride salts (LnCl3) are mixed with transition metals and excess of alkali or alkali earth metal salts or salt mixtures (LiCl, NaCl, KCl). These are added to an alumina crucible, placed in a quartz tube, and sealed under a vacuum. This is heated up to around 1000 °C and slowly cooled to a temperature above the melting point of the salt and at that temperature, the reaction is taken out of the furnace. The excess salt is removed, and the resulting product is analyzed using X-ray diffraction techniques, scanning electron microscopy, and spectroscopic methods such as Raman, UV-Visible, and FTIR spectroscopy.

37 - INORGANIC, ORGANIC, PHYSICAL AND ANALYTICAL C↗
DOE OSTI2023

Design and testing of an enriched uranium fueled molten salt irradiation vehicle

Molten salt reactors (MSRs) have garnered increasing attention recently with several demonstration efforts on the way. A key challenge to the licensing basis for these reactors is the lack of experimental data on fueled salts. This is expected to be crucial to the safety evaluation and licensing basis of reactors of this type deployed in the future. While capability for irradiating molten salts has started being reestablished in the recent decade, no enriched fuel irradiation capability has been developed and tested as of yet. A new experiment vehicle under development at Idaho National Laboratory (INL) is presented here. The Molten-salt Research Temperature-controlled Irradiation (MRTI) experiment was developed to host enriched-uranium bearing salt samples to be irradiated at a test reactor within the lab complex. One of the key scientific objectives is to provide irradiated salt samples for post irradiation examination (PIE) to study the impact of fission product generation and neutron/gamma radioactivity on the salt solution and salt-facing wall material. This paper provides a detailed overview of the mechanical design of the experiment, followed by an overview of the fabrication and assembly of an initial prototype vehicle (with non-fuel bearing salt). A summary of the key analyses conducted as a part of the performance and safety evaluation is then provided. Lastly, an overview of the test conducted in prototypic out-of-pile (non-neutron) environment are shown. These evaluations provide the foundation for a planned irradiation of and enriched uranium-bearing chloride salt sample in the near term. The upcoming irradiation will contain 13cm 3 of UCl 3 -NaCl salt (93% enrichment) generating around 20 W/cm 3 of fission energy during irradiation and a temperature range that can be contained between bounds of 525-900°C.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1972

Al/Cl2 molten salt battery

Molten salt battery has been developed with theoretical energy density of 5.2 j/kg (650 W-h/lb). Battery, which operates at 150 C, can be used in primary mode or as rechargeable battery. Battery has aluminum anode and chlorine cathode. Electrolyte is mixture of AlCl3, NaCl, and some alkali metal halide such as KCl.

Giner, J.↗
DOE OSTI2025

Initial Design of SABRE Fueled Molten Salt Experiment Irradiation Vehicle

Molten Salt Reactors (MSRs) are emerging as promising advanced reactor technologies, utilizing molten salts for both fuel and primary cooling. These reactors may offer advantages such as passive safety, enhanced economic viability, and efficient waste reprocessing while operating at high temperatures and low pressures, which leads to increased system efficiency and reduced mechanical stress on containment structures. However, challenges arise from the complex chemistry and high corrosion rates of fueled molten salts, alongside the volatility of certain fission products during irradiation. The accumulation of these fission products can alter the fuel salt chemistry, affecting corrosion potential and radioactive source terms. Therefore, understanding these phenomena under neutron irradiation is essential for future MSR designs. The SABRE (Salt and Actinide Burnup in a Reactor Environment) experiment, currently in conceptual design at Idaho National Laboratory (INL), aims to investigate these challenges by conducting a drop-in capsule experiment in the Advanced Test Reactor (ATR). The primary objectives include achieving a minimum burnup of 2 GWd/MTU and characterizing fission products while studying corrosion behavior in molten salt systems. This innovative experiment will leverage recent advancements in ATR capabilities, allowing for the safe irradiation of molten salts, thereby advancing the understanding and qualification of MSR technology for future nuclear power generation.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Infrastructure and Testing Needs for Molten Salt Reactor Safeguards

Molten salt reactors (MSRs) are an attractive advanced reactor technology because of their increased fuel utilization and efficiency, the ease of fueling, and the potential to use alternative fuel cycles, including thorium and breeder/burner scenarios. Since an MSR has never been domestically operated for commercial electricity production, minimal infrastructure exists to support performance and materials testing, reactor licensing (including research, test, and operating reactors), and technology development in general. These factors could present challenges for the commercialization of the proposed design technology. Several research and development efforts and investments have begun to identify and supplement the infrastructure to accommodate the molten salt concept, including the United States Department of Energy Office of Nuclear Energy Molten Salt Reactor Program. This report reviews safeguards technology and domestic infrastructure to support the evaluation of nuclear safeguards (primarily material control and accounting) measures and approaches for salt-fueled MSRs. Recommendations for potential priority infrastructure investments, including safeguards measurement test beds and future research, are presented.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Corrosion Testing Trade Study on Testing Methods in Molten Salts

In assessing molten salt compatibility with structural materials, static testing is often reported because it is easy to conduct. However, in order to assess mass transfer, where material dissolves in the salt in the hot section and may precipitate out of the liquid in colder regions, a flowing salt experiment in a temperature gradient is needed. While a forced convection or pumped loop produces prototypic flowing conditions, it also is a multi-million dollar investment. Among the less expensive dynamic testing options, the thermal convection loop (TCL) was favored during the 1960’s development of molten salt reactor technology. Because the workforce and core facilities are currently available to conduct TCL experiments, it is the least expensive strategy to evaluate candidate structural alloys in flowing molten salt conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Gamma-ray spectra analyses of molten salts in spent nuclear fuels pyroprocessing facilities for mass measurement

To evaluate radioactive tracer dilution and gamma spectroscopy as a safeguards technique for monitoring the mass of liquid salt in molten salt systems, the gamma spectroscopy data of salt samples from the pyroprocessing facilities in Idaho National Laboratory were acquired and analyzed. The primary focus is the uncertainty analysis of the gamma radioactivity of 154 Eu isotope in the molten salts. The facilities include an electrorefiner for pyroprocessing spent oxide fuels (SOF-ER) and Mark-IV ER for processing the metallic fuels from Experimental Breeder Reactor-II (EBR-II). The relative gamma radioactivity uncertainty was consistently at 3% for 137 Cs for both Mark-IV ER and SOF-ER salts. However, for 154 Eu, it was 8% for SOF-ER salt and 7% for Mark-IV ER salt. Here, the main reason for the higher uncertainty for 154 Eu is believed to be the lower counting statistics in gamma spectroscopy. To improve the gamma radioactivity uncertainty of isotope 154 Eu, a longer data acquisition time (12 h instead of 4 h) and a higher count rate gamma detector for gamma spectroscopy were tested and it was found that the uncertainty for 154 Eu was significantly improved from 7% or 8–3%.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Protection of graphite from salt and gas permeation in molten salt reactors

The reactor core, moderator and reflectors of a thermal spectrum advanced molten salt reactor will constitute multi-tons of graphite. Porous reactor-grade graphite, if unprotected, can be permeated by molten salt depending on the infiltrating pressure differential and entrance diameters of accessible graphite pores. Salt and gas permeation of graphite can affect microstructural properties and radiation behavior but also facilitate diffusion, deposition and retention of fission products and tritium. Because of the significant void volume of nuclear graphite, fission products and tritium retention due to salt permeation necessitates seal coatings or pore impregnation to reduce open porosity. Alternatively, very fine-grained graphite grades with low Xe permeability are being developed. In this work, we survey the current technologies for mitigating salt and gas transport into graphite.

36 MATERIALS SCIENCE↗