Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ni coarsening”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Phase instabilities in austenitic steels during particle bombardment at high and low dose rates

Disruption of phase stability by energetic particle bombardment is a major challenge in designing advanced radiation-tolerant alloys and ion beam processing of nanocomposites. Particularly, ballistic dissolution susceptibility of different solute nanocluster species in alloys is poorly understood. Here, low dose rate neutron irradiations were conducted on a Fe-Cr-Ni based austenitic steel in the BOR-60 reactor (9.4 × 10 -7 dpa/s, 318 °C) followed by accelerated dose rate ion irradiations at multiple temperatures ( 10 -3 dpa/s, 380 – 420 °C). Using atom probe tomography, the stability of radiation-enhanced Cu-rich and radiation-induced Ni-Si-Mn-rich nanoclusters was evaluated. During neutron irradiation, Cu-rich clusters nucleated with their core concentrations progressively increasing with dose, while Ni-Si-Mn-rich clusters formed and evolved into G-phase precipitates. Ion irradiations dramatically altered the nanoclusters. Cu-rich clusters were ballistically dissolved, but Ni-Si-Mn-rich clusters remained stable and coarsened with dose at 400 and 420 °C, highlighting that different nanocluster species in a single microstructure can have innately distinct ballistic dissolution susceptibilities. Solute-specific recoil rates were incorporated into the Heinig precipitate stability model, which shows that in addition to radiation-enhanced diffusion, recovery from ballistic dissolution depends on solute concentration gradient near cluster interfaces. Finally, the combined experimental-modeling study quantified the critical temperatures and damage rates where ballistic dissolution dominates for each cluster species.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Shuffling mode competition leads to directionally anisotropic mobility of faceted Σ11 boundaries in fcc metals

Faceted grain boundaries can migrate in interesting and unexpected ways. For example, faceted Σ11 <110> tilt grain boundaries were observed to exhibit mobility values that could be strongly dependent on the direction of migration. In order to understand whether this directionally-anisotropic mobility is a general phenomenon and to isolate mechanistic explanations for this behavior, molecular dynamics simulations of bicrystals evolved under an artificial driving force are used to study interface migration for a range of boundary plane inclination angles and temperatures in multiple face centered cubic metals (Al, Ni, and Cu). We find that directionally anisotropic mobility is active in a large fraction of these boundaries in Ni and Cu and should therefore impact the coarsening of polycrystalline materials. On the other hand, no such anisotropy is observed in any of the Al boundaries, showing that this behavior is material-dependent. Migration of the faceted boundaries is accomplished through transformation events at facet nodes and incommensurate boundary plane facets, which are termed shuffling modes. Three major shuffling modes have been identified, namely Shockley shuffling, slip plane shuffling, and disordered shuffling. A shift from the first two ordered modes to the third disordered mode is found to be responsible for reducing or removing directionally-anisotropic mobility, especially at the highest temperatures studied.

36 MATERIALS SCIENCE↗
NASA NTRS2004

The Role of Rhenium on the Temporal Evolution of the Nanostructure of a Model Ni-Al-Cr-Re Superalloy

Rhenium (2 at.%) additions to a model Ni-8.5 at.% Cr-10 at.% Al alloy are studied with respect to its effects on the temporal evolution of the nanostructure and the partitioning behavior of the four elements between the gamma (fcc) and gamma' (L1(sub 2)) phases. Chemical evolution of this quaternary alloy aged at 1073 K from 0.25 to 264 h, is investigated by three-dimensional atom-probe (3DAP) microscopy. The morphology of gamma'-precipitates remains spheroidal, even at an aging time of 264 h. The results demonstrate that Re slows the coarsening of gamma'-precipitates, in comparison to the ternary Ni-10 at.% A1-8.5 at.% Cr alloy at 1073 K.

Yoon, Kevin E.↗
NASA NTRS1985

The development of gamma-gamma-prime lamellar structures in a nickel-base superalloy during elevated temperature mechanical testing

The kinetics of the formation and subsequent development of the directional coarsening of the gamma-prime precipitate in model Ni-Al-Mo-Ta superalloy single crystals are examined during tensile creep under various stress levels at 982 and 1038 C. Special attention is given to the gamma and gamma-prime relation to creep time and strain in order to trace the changing gamma-gamma-prime morphology. Directional coarsening of gamma-prime is found to begin during primary creep and its rate is shown to increase with an increase in temperature or stress level. The length of gamma-prime thickness increased linearly with time up to a plateau reached after the onset of steady state creep. The raft thickness, equal to the gamma-prime size, remained constant at this initial value up through the onset of the tertiary creep. The interlaminar spacing indicates the stability of directionally coarsened structure.

Mackay, R. A.↗
DOE OSTI2023

Heterogeneous 3D Morphological Evolution of Ni Microparticles in Molten Salts: Visualized by Operando Synchrotron X-ray Nano-tomography

Ni-based superalloys are promising materials for high-temperature molten salt (MS) energy generation and storage. Studying morphological and chemical evolution of pure Ni in MS provides fundamental knowledge for MS technologies and corrosion mitigation. Here, in this study, real-time 3D morphological changes of Ni microparticles in molten KCl-MgCl 2 were studied by operando synchrotron X-ray nano-tomography at 700°C. Rapid Ni particle agglomeration occurred, without significant chemical reactions, such as oxide or chloride formation. The morphological growth evolved differently from classical coarsening or sintering behaviors and occurred nonuniformly, with other regions showing slight dissolution of Ni. Ni nanoparticles were found to be dispersed in many areas of the samples, either from microparticle dissolution or other radiation-induced nanoparticle formation mechanisms. This study discusses important factors, i.e., thermal gradient, amounts of salt and metals, and radiation effect, that influence morphological changes of materials in MS, critical for fundamental understanding of material–MS interactions as well as for practical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Assessment of binary eutectic Ni alloys for high-temperature applications via laser remelting

It has been recently demonstrated that eutectic alloys processed by additive manufacturing have excellent high-temperature mechanical properties. We suggest that nickel-base eutectic alloys may enable new combinations of structural and functional properties. To this end, we investigate the processability, microstructure, and thermal stability of five, binary near-eutectic Ni-X (X = B, Ce, La, Y, and Zr) alloys processed via surface laser-remelting. The microstructure of all alloys contain a two-phase lamellar eutectic microstructure consisting of γ-Ni and intermetallic phases; this microstructure is significantly finer (100–200 nm lamellar spacing) in the laser-remelted alloys than in the cast substrate (0.5–1.0 µm lamellar spacing). The microhardness of the laser-remelted alloys (550–770 HV) is 35–50% higher than that of the cast alloys (370–570 HV) due to this finer eutectic spacing. An anomalous eutectic microstructure appears at the meltpool boundaries, containing globular and lamellar γ-Ni phases. The alloys contain a high volume fraction (>50 vol%) of intermetallic phase which forms a continuous network, causing brittleness. Following laser-remelting trials, the alloys showed a high density of solid-state cracks, except for the Ni-Zr alloy which processed well. During thermal exposure at 700 and 900°C for up to 500 h, the eutectic microstructure coarsens. Coarsening occurs heterogeneously and initiates at the meltpool boundaries. This process occurs more slowly in the Ni-Zr and Ni-Y alloys, and more rapidly in the remaining alloys, resulting in greater microhardness retention in the Ni-Zr and Ni-Y alloys following thermal exposure at 700°C. Thus, among the five alloys, the Ni-Zr system exhibits a good combination of high-temperature mechanical properties and processability. Here, we conclude with recommendations for future work on designing additively manufactured alloys based on these eutectic Ni systems.

Additive manufacturing↗
DOE OSTI2020

Coupling computational thermodynamics with density-function-theory based calculations to design L12 precipitates in Fe Ni based alloys

Achieving a high-volume fraction of thermodynamically stable L12-type precipitates that are resistant to coarsening is of great importance for the development of low-cost FeNi based austenitic steels. With the aid of computational thermodynamics, this work designed two model alloys: Fe-37.4Ni-6.1Al-2.9Ti (FNAT) and Fe-45.2Ni-5.9Al-8.5Si (FNAS). Both alloys were designed to contain a similar amount of L1 2 precipitate in Fe-Ni matrix without forming other precipitates. Density-Function-Theory (DFT) calculation was coupled with computational thermodynamics to predict the critical radius at which the precipitates change shape from spherical to cuboidal. The calculation results suggest that critical radius for the FNAT alloy is about two orders of magnitude larger than that for the FeNiAlSi alloy. Phase stability and morphology of the L1 2 precipitates in these two alloys were experimentally investigated through X-ray diffraction, atom probe tomography, and scanning and transmission electron microscopy. The L1 2 precipitates in the FeNiAlSi system were found to be cuboidal and rod shaped, with much larger size than the spherical ones in the FeNiAlTi system, agreeing with the calculation results. This work suggested that coupling computational thermodynamics with DFT calculations can be reliably used to design L1 2 precipitates in FeNi based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

DOE-BU-26096-4

The infiltration of nanoparticle electrocatalysts into solid oxide fuel cell (SOFC) electrodes has been proven to produce a high density of electrochemically active sites, and reduce charge transfer polarization losses in SOFC electrodes. This is crucial for intermediate temperature operation, as these losses increase greatly at lower temperatures. Nickel-yttria stabilized zirconia (Ni-YSZ) cermets are low-cost, and exhibit excellent stability, but their main disadvantage stems from nickel coarsening and performance loss over their operational lifetimes. Infiltration of electrocatalyst nanoparticles has been shown to mitigate nickel coarsening and the consequent anode degradation. In this work, the effects of these infiltrants have been observed in a standard Ni-YSZ electrode. In addition to nickel, mixed ionic and electronic conducting (MIEC) phases have been infiltrated into Ni-YSZ scaffolds and their performance characterized using electrochemical impedance spectroscopy (EIS). Cross-sectional microscopy of fractured cells has been used to compare electrode microstructure and particle statistics. A model has been proposed to explain the origin of anode performance enhancement from nanoscale electrocatalysts.

Mo, Boshan↗
NASA NTRS1985

The influence of cobalt, tantalum, and tungsten on the microstructure of single crystal nickel-base superalloys

The influence of composition on the microstructure of single crystal nickel-base superalloys was investigated. Co was replaced by Ni, and Ta was replaced by either Ni or W, according to a matrix of compositions based on MAR-M247. Substitution of Ni for Co caused an increase in gamma-prime solvus temperature, an increase in gamma-gamma-prime lattice mismatch, and the precipitation of W-rich phases in the alloys with high refractory metal levels. Substitution of Ni for Ta caused large decreases in gamma-prime solvus temperature, gamma-prime volume fraction, and gamma-gamma-prime lattice mismatch, whereas substitution of W for Ta resulted in smaller decreases in these features. For the alloys with gamma-prime particles that remained coherent, substitution of Ni for Co caused an increase in gamma-prime coarsening rate. The two alloys with the largest magnitude of lattice mismatch possessed gamma-prime particles which lost coherency during unstressed aging and exhibited anomalously low coarsening rates. Creep exposure at 1000 C resulted in the formation of gamma-prime lamellae oriented perpendicular to the applied stress axis in all alloys.

Nathal, M. V.↗
DOE OSTI2023

Microstructure and mechanical properties of hypoeutectic Al–6Ce–3Ni-0.7Fe (wt.%) alloy

Here, a hypoeutectic, Fe-modified Al–Ce–Ni alloy (Al–6Ce–3Ni-0.7Fe, wt.%) is studied in terms of microstructure, thermal stability, ambient temperature strengthening, and creep resistance. The as-cast microstructure consists of primary Al dendrites and interdendritic binary eutectic regions (Al–Al11Ce3 and/or Al–Al9(Fe,Ni)2), with micron/submicron lamellar spacing, depending on the location along the height of the ingot. The cast alloy exhibits excellent coarsening resistance at 400 °C, with mostly unchanged microstructure and microhardness after 6 weeks of aging, indicating good thermal stability of Al11Ce3 and Al9(Fe,Ni)2. Orowan strengthening and load transfer are identified as strengthening mechanisms at ambient and elevated temperature. A high volume fraction of the intermetallic phases (providing load transfer) and relatively coarse eutectic spacing (for modest Orowan strengthening) result in a moderate as-cast microhardness of 566 ± 32 MPa. Creep resistance at 300 and 350 °C is similar to a binary Al-12.5Ce eutectic alloy (with twice the Ce content) because of two countering effects: Al–6Ce–3Ni-0.7Fe shows a higher volume fraction of strengthening intermetallic phases, but it also exhibits a large fraction of primary Al dendrites which weaken the alloy. By contrast, the alloy, when laser-remelted at the surface, has a fully eutectic microstructure without primary aluminum dendrites achieved by high undercooling on solidification, with a refined network of eutectic phases that doubles the microhardness as compared to the cast alloy. Whereas coarsening is faster due to the shorter diffusion distances between the eutectic phases, hardness remains ~30% higher than the as-cast alloy after ~6 weeks aging at 400 °C.

36 MATERIALS SCIENCE↗
NASA NTRS1987

Advanced powder metallurgy aluminum alloys via rapid solidification technology, phase 2

Marko's rapid solidification technology was applied to processing high strength aluminum alloys. Four classes of alloys, namely, Al-Li based (class 1), 2124 type (class 2), high temperature Al-Fe-Mo (class 3), and PM X7091 type (class 4) alloy, were produced as melt-spun ribbons. The ribbons were pulverized, cold compacted, hot-degassed, and consolidated through single or double stage extrusion. The mechanical properties of all four classes of alloys were measured at room and elevated temperatures and their microstructures were investigated optically and through electron microscopy. The microstructure of class 1 Al-Li-Mg alloy was predominantly unrecrystallized due to Zr addition. Yield strengths to the order of 50 Ksi were obtained, but tensile elongation in most cases remained below 2 percent. The class 2 alloys were modified composition of 2124 aluminum alloy, through addition of 0.6 weight percent Zr and 1 weight percent Ni. Nickel addition gave rise to a fine dispersion of intermetallic particles resisting coarsening during elevated temperature exposure. The class 2 alloy showed good combination of tensile strength and ductility and retained high strength after 1000 hour exposure at 177 C. The class 3 Al-Fe-Mo alloy showed high strength and good ductility both at room and high temperatures. The yield and tensile strength of class 4 alloy exceeded those of the commercial 7075 aluminum alloy.

Ray, Ranjan↗
DOE OSTI2020

Characterizing Performance of Electrocatalyst Nanoparticles Infiltrated into Ni-YSZ Cermet Anodes for Solid Oxide Fuel Cells

The infiltration of nanoparticle electrocatalysts into solid oxide fuel cell (SOFC) electrodes has been proven to produce a high density of electrochemically active sites, and reduce charge transfer polarization losses for SOFC electrodes. This is crucial for intermediate temperature operation, as these losses increase greatly at lower temperatures. Nickel-yttria stabilized zirconia (NiYSZ) cermets are low-cost, and exhibit excellent stability, but their main disadvantage stems from nickel coarsening and performance loss over their operational lifetimes. Infiltration of electrocatalyst nanoparticles has been shown to mitigate nickel coarsening and the consequent anode degradation. In this study, the effects of these infiltrants are observed in a standard Ni-YSZ electrode. In addition to nickel, mixed ionic and electronic conducting (MIEC) phases were infiltrated into Ni-YSZ scaffolds and their performances were characterized using electrochemical impedance spectroscopy (EIS). Cross-sectional microscopy of fractured cells was used to compare electrode microstructure and particle statistics. A model is proposed for how the nanoparticle electrocatalysts improve the anode performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Growth and structural transitions of core-shell nanorods in nanocrystalline Al-Ni-Y

Unique nanorod precipitates with a core-shell structure are found to nucleate from the grain boundaries of a bulk nanocrystalline Al-Ni-Y alloy fabricated via powder consolidation, contributing significantly to stabilization and strengthening. The local structure, chemistry, and evolution of these features during annealing are reported here. In the as-consolidated state, the nanorods can be either structurally ordered or disordered, yet a consistent chemical patterning is found where the core is primarily Al plus C while the shell is enriched with Y. As annealing time increases, more nanorods transform to an ordered structure as they coarsen while the core composition remains unchanged. In contrast, the shell chemistry transitions from Y-rich to Ni-rich with longer annealing treatments, most likely due to the different diffusivities of Y and Ni in Al. Furthermore, a spatial and chemical correlation between the nanorods and amorphous complexions is observed, suggesting that these complexions serve as preferential nucleation sites.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Substitution-Mediated Calcination of Nickel-Based Cathodes: Decoupling Lithiation and Crystallization

Nickel-based layered cathodes such as LiNiO 2 offer high energy density for lithium-ion batteries, yet improvements in cycling performance and safety are required for practical use–often achieved through manganese and cobalt substitution as in LiNi 0.80 Mn 0.10 Co 0.10 O 2 (NMC811). However, how such substitution impacts calcination, the key process that governs lithiation, structural ordering, crystallization, and ultimately the resulting material properties, remains unclear. Here, in this study, we investigate substitution-mediated calcination dynamics in NMC811 compared to LiNiO 2 using multiscale-correlated in situ spectroscopy and atomistic-to-mesoscale modeling. While both systems progress through the same sequence of intermediates toward the thermodynamically favored layered phase, NMC811 exhibits an earlier onset of layering, concurrent with hydroxide decomposition followed by sluggish crystallization. Modeling reveals that Mn and Co lower the energy barrier for lithium incorporation and ordering but increase the penalty for interlayer gliding, thereby slowing crystal growth at elevated temperatures. This substitution-mediated decoupling of lithiation and crystallization explains the fine-grained microstructure observed in NMC811 versus coarsened particles in LiNiO 2 and establishes a mechanistic framework for predictive microstructure engineering of Ni-based cathodes.

Calcination↗
DOE OSTI2021

Grain boundary velocity and curvature are not correlated in Ni polycrystals

Grain boundary velocity has been believed to be correlated to curvature, and this is an important relationship for modeling how polycrystalline materials coarsen during annealing. We determined the velocities and curvatures of approximately 52,000 grain boundaries in a nickel polycrystal using three-dimensional orientation maps measured by high-energy diffraction microscopy before and after annealing at 800°C. Unexpectedly, the grain boundary velocities and curvatures were uncorrelated. Instead, we found strong correlations between the boundary velocity and the five macroscopic parameters that specify grain boundary crystallography. The sensitivity of the velocity to grain boundary crystallography might be the result of defect-mediated grain boundary migration or the anisotropy of the grain boundary energy. The absence of a correlation between velocity and curvature likely results from the constraints imposed by the grain boundary network and implies the need for a new model for grain boundary migration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2010

Microstructure Modeling of Third Generation Disk Alloys

The objective of this program was to model, validate, and predict the precipitation microstructure evolution, using PrecipiCalc (QuesTek Innovations LLC) software, for 3rd generation Ni-based gas turbine disc superalloys during processing and service, with a set of logical and consistent experiments and characterizations. Furthermore, within this program, the originally research-oriented microstructure simulation tool was to be further improved and implemented to be a useful and user-friendly engineering tool. In this report, the key accomplishments achieved during the third year (2009) of the program are summarized. The activities of this year included: Further development of multistep precipitation simulation framework for gamma prime microstructure evolution during heat treatment; Calibration and validation of gamma prime microstructure modeling with supersolvus heat treated LSHR; Modeling of the microstructure evolution of the minor phases, particularly carbides, during isothermal aging, representing the long term microstructure stability during thermal exposure; and the implementation of software tools. During the research and development efforts to extend the precipitation microstructure modeling and prediction capability in this 3-year program, we identified a hurdle, related to slow gamma prime coarsening rate, with no satisfactory scientific explanation currently available. It is desirable to raise this issue to the Ni-based superalloys research community, with hope that in future there will be a mechanistic understanding and physics-based treatment to overcome the hurdle. In the mean time, an empirical correction factor was developed in this modeling effort to capture the experimental observations.

Jou, Herng-Jeng↗
DOE OSTI2021

Exploring the Role of Humidity, Temperature, and Mixed Ionic and Electronic Conductivity on SOFC Anode Electrocatalysis

Infiltration of nanoscale electrocatalysts into Ni/yttria-stabilized zirconia (Ni-YSZ) cermets has been shown to improve the electrochemical performance of solid oxide fuel cell (SOFC) anodes. While infiltrated electrodes in SOFCs result in improved cell performance, long-term operation leads to coarsening of the infiltrated nanoparticles and negates the short-term performance improvements. This study explores the roles of humidity, temperature, and number of cycles of nanocatalyst infiltration in improving mixed conduction within the Ni-YSZ electrode. Two mixed conduction phases were studied: Gd 0.1 Ce 0.9 O 2-δ (GDC) as an infiltrant into Ni-YSZ electrodes, and Ni/transition metal doped-YSZ electrodes infiltrated with Ni. Analysis of impedance data from these cells shows improved electrochemical performance in infiltrated cells with mixed conduction compared with infiltrated cells containing purely ionic and electronic conducting phases. Improved anode performance is attributed to the availability of electronic pathways through predominantly ionic-conducting phases to connect distant Ni nanoparticles and/or Ni grains.

25 ENERGY STORAGE↗
NASA NTRS1984

Factors which influence directional coarsening of Gamma prime during creep in nickel-base superalloy single crystals

Changes in the morphology of the gamma prime precipitate were examined as a function of time during creep at 982 C in 001 oriented single crystals of a Ni-Al-Mo-Ta superalloy. In this alloy, which has a large negative misfit of -0.80 pct., the gamma prime particles link together during creep to form platelets, or rafts, which are aligned with their broad faces perpendicular to the applied tensile axis. The effects of initial microstructure and alloy composition of raft development and creep properties were investigated. Directional coarsening of gamma prime begins during primary creep and continues well after the onset of second state creep. The thickness of the rafts remains constant up through the onset of tertiary creep a clear indication of the stability of the finely-spaced gamma/gamma prime lamellar structure. The thickness of the rafts which formed was equal to the initial gamma prime size which was present prior to testing. The single crystals with the finest gamma prime size exhibited the longest creep lives, because the resultant rafted structure had a larger number of gamma/gamma prime interfaces per unit volume of material. Reducing the Mo content by only 0.73 wt. pct. increased the creep life by a factor of three, because the precipitation of a third phase was eliminated.

Mackay, R. A.↗