Search NASA⌕ Search

SEARCH · Search NASA

Results for “Number”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Coherent large-scale structures in high Reynolds number supersonic jet of Mach number 1.4

Large-scale coherent structures are found to exist in fully expanded shock free supersonic jets with Reynolds number 1.6 million and Mach number 1.4. The jet was excited by a weak upstream tone to extract the large-scale structures from the random turbulence. The most preferential excitation Strouhal number is found to be in the vicinity of 0.4, and the dependence of the large-scale structure phase velocity on the excitation Strouhal number shows a similar trend to that found for subsonic acoustically excited jets.

Lepicovsky, J.↗

A study of the effects of Reynolds number and Mach number on constant pressure coefficient jump for shock-induced trailing-edge separation

The influence of Mach and Reynolds numbers as well as airfoil and planform geometry on the phenomenon of constant shock jump pressure coefficient for conditions of shock induced trailing edge separation (SITES) was studied. It was demonstrated that the phenomenon does exist for a wide variety of two and three dimensional flow cases and that the influence of free stream Mach number was not significant. The influence of Reynolds number was found to be important but was not strong. Airfoil and planform geometric characteristics were found to be very important where the pressure coefficient jump was shown to vary with the sum of: (1) airfoil curvature at the upper surface crest, and (2) camber surface slope at the trailing edge. It was also determined that the onset of SITES could be defined as a function of airfoil geometric parameters and Mach number normal to the leading edge. This onset prediction was shown to predict the angle of onset to within + or - 1 deg accuracy or better for about 90% of the cases studied.

Cunningham, Atlee M., Jr.↗

The Aerodynamic Design and Calibration of an Asymmetric Variable Mach Number Nozzle with a Sliding Block for the Mach Number Range 1.27 to 2.75

A method of designing as asymmetric, fixed geometry, variable Mach number nozzle has been developed by using the method of characteristics. A small nozzle conforming to the analytically determined ordinates was constructed and calibrated over a range of Mach numbers extending from 1.27 to 2.75. The results show the variation in Mach number to be plus or minus 0.01 or less and in the flow direction to be plus or minus 0.2 degrees within the test section. The range of Mach numbers from 1.27 to 2.75 was obtained by translating the lower block in a straight line parallel to the test-section center line for a distance of 2.17 test-section heights.

NOZZLES↗

Investigation at Supersonic Speeds of the Variation with Reynolds Number and Mach Number of the Total, Base, and Skin-friction Drag of Seven Boattail Bodies of Revolution Designed for Minimum Wave Drag

Results are presented from an investigation of the variation with Reynolds number and Mach number of the total, base, and skin-friction drag of seven boattail bodies of revolution designed for minimum wave drag according to the theory of NACA-TN-2550. The tests covered a Reynolds number range from approximately 1.0 x 10(6) to 10.0 x 10(6) at Mach numbers of 1.62, 1.93, and 2.41 respectively.

Bromm, August, F , jr↗

Lewis number and Damkohler number effects in vort ex-flame interactions

A combined experimental-numerical study of the interaction of a two-dimensional vortex pair with a plane premixed laminar flame has been carried out. The selected geometry is two-dimensional in order to allow for the use of quantitative line-of-sight measurement techniques and for comparisons with two-dimensional direct numerical simulations. The experiment is used to identify possible effects of the Lewis number and of radiative heat losses, and direct numerical simulations reproducing the experimental conditions are used to investigate the role of the Lewis number, of heat losses, and of multi-step kinetics. The heat losses considered in this study are essentially radiative losses from the burnt gases and do not include conductive losses to the walls. This report presents the final results of this study of vortex-flame interactions. The main result is the creation of experimental data sets of vortex-flame interactions, which demonstrate the importance of the Lewis and Damkohler numbers to the flame and which allow for comparison with direct numerical simulations. In turn, the comparison between experimental and numerical results shows that the Lewis number effects and complex chemistry play significant roles, which can be reproduced using a two-step reaction mechanism.

Samaniego, Jean-Michael↗

Lift, Drag, and Pitching Moments of an Arrow Wing Having 80 Degree of Sweepback at Mach Numbers from 2.48 to 3.51 and Reynolds Numbers up to 11.0 Million

Measurements were made of the lift, drag, and pitching moments on an arrow wing (taper ratio of zero) having an aspect ratio of 1.4 and a leading-edge sweepback of 80 (degrees). The wing was designed to have a subsonic leading-edge and a Clark-Y airfoil with a thickness ratio of 12 percent of the chord perpendicular to the wing leading edge. The wing was tested both with and without the wing tips bent upward in an attempt to alleviate possible flow separation in the vicinity of the wing tips. Small jets of air were used to fix transition near the wing leading edge. Force results are presented for Mach numbers of 2.48, 2.75, 3.04, 3.28, and 3.51 at Reynolds numbers of 3.5 and 9.0 million and for a Mach number of 3.04 at a Reynolds number of 11.0 million. The measured aerodynamic characteristics are compared with those estimated by linear theory. The maximum lift-drag ratio measured was much less than that predicted. This difference is attributed to lack of full leading-edge thrust and to the experimental lift-curve slope being about 20 percent below the theoretical value.

Hopkins, Edward J.↗

Role of Turbulent Prandtl Number on Heat Flux at Hypersonic Mach Number

Present simulation of turbulent flows involving shock wave/boundary layer interaction invariably overestimates heat flux by almost a factor of two. One possible reason for such a performance is a result of the fact that the turbulence models employed make use of Morkovin's hypothesis. This hypothesis is valid for non-hypersonic Mach numbers and moderate rates of heat transfer. At hypersonic Mach numbers, high rates of heat transfer exist in regions where shock wave/boundary layer interactions are important. As a result, one should not expect traditional turbulence models to yield accurate results. The goal of this investigation is to explore the role of a variable Prandtl number formulation in predicting heat flux in flows dominated by strong shock wave/boundary layer interactions. The intended applications involve external flows in the absence of combustion such as those encountered in supersonic inlets. This can be achieved by adding equations for the temperature variance and its dissipation rate. Such equations can be derived from the exact Navier-Stokes equations. Traditionally, modeled equations are based on the low speed energy equation where the pressure gradient term and the term responsible for energy dissipation are ignored. It is clear that such assumptions are not valid for hypersonic flows. The approach used here is based on the procedure used in deriving the k-zeta model, in which the exact equations that governed k, the variance of velocity, and zeta, the variance of vorticity, were derived and modeled. For the variable turbulent Prandtl number, the exact equations that govern the temperature variance and its dissipation rate are derived and modeled term by term. The resulting set of equations are free of damping and wall functions and are coordinate-system independent. Moreover, modeled correlations are tensorially consistent and invariant under Galilean transformation. The final set of equations will be given in the paper.

Xiao, X.↗

Independent Effects of Reynolds Number and Mach Number on the Aerodynamics of an Iced Swept Wing

Aerodynamic assessment of icing effects on swept wings is an important component of a larger effort to improve three-dimensional (3D) icing simulation capabilities. An understanding of ice-shape geometric fidelity and Reynolds and Mach number effects on the iced-wing aerodynamics is needed to guide the development and validation of ice-accretion simulation tools. To this end, wind tunnel testing was carried out for a 13.3-percent-scale semispan wing based upon the Common Research Model airplane configuration. The wind tunnel testing was conducted at the Office National d’Etudes et de Recherches Aérospatiales (ONERA) F1 pressurized wind tunnel with Reynolds numbers of 1.6 x 10(exp 6) to 11.9 x 10(exp 6 ) and Mach numbers of 0.09 to 0.34. Five different configurations were investigated using fully 3D, high-fidelity artificial ice shapes that maintain nearly all of the 3D ice-accretion features documented in prior icing wind tunnel tests. These large, leading-edge ice shapes were nominally based upon airplane holding in icing conditions scenarios. For three of these configurations, lower fidelity simulations were also built and tested. The results presented in this paper show that while Reynolds and Mach number effects are important for quantifying the clean-wing performance, there is very little to no effect for an iced wing with 3D, high-fidelity artificial ice shapes or 3D smooth ice shapes with grit roughness. These conclusions are consistent with the large volume of past research on iced airfoils. However, some differences were also noted for the associated stalling angle of the iced swept wing and for various lower fidelity versions of the leading-edge ice accretion. More research is planned to further investigate the key features of ice-accretion geometry that must be simulated in lower fidelity versions in order to capture the essential aerodynamics.

Aircraft icing↗

On the use of freon-12 for increasing Reynolds number in wind-tunnel testing of three dimensional aircraft models at subcritical and supercritical Mach numbers

The aerodynamic suitability of Freon-12 for general wind-tunnel testing was investigated at low and high subsonic speeds. Static aerodynamic characteristics of two transport airplane models were determined from strain gage balance measurements in both air and Freon-12 at several Reynolds numbers. A low-speed high-lift configuration was evaluated at Mach number 0.25, and a high-speed cruise wing-fuselage combination was tested at Mach numbers up to 0.825. The data obtained in air and in Freon-12 agree well, even in stalled flow, until compressibility effects evidently become significant in air and in Freon-12 agree well, even in stalled flow, until compressibility effects evidently become significant in air.

Treon, S. L.↗

An experimental investigation of turbulent boundary layers at high Mach number and Reynolds numbers

Skin friction, heat transfer and pressure measurements were obtained in laminar, transitional and turbulent boundary layers on flat plates at Mach numbers from 7 to 13 at wall-to-free stream stagnation temperature ratios from 0.1 to 0.3. Measurements in laminar flows were in excellent agreement with the theory of Cheng. Correlations of the transition measurements with measurements on flight vehicles and in ballistic ranges show good agreement. Our transition measurements do not correlate well with those of Pate and Schueler. Comparisons have been made between the skin friction and heat transfer measurements and the theories of Van Driest, Eckert and Spalding and Chi. These comparisons reveal in general that at the high end of our Mach number range (10-13) the theory of Van Driest is in best agreement with the data, whereas at lower Mach numbers (6.5-10) the Spalding Chi theory is in better agreement with the measurements.

Holden, M. S.↗

Aerodynamic Characteristics at Mach Numbers from 0.6 to 2.16 of a Supersonic Cruise Fighter Configuration with a Design Mach Number of 1.8

An investigation was made in the Langley 8-foot transonic tunnel and the Langley Unitary Plan wind tunnel, over a Mach number range of 0.6 to 2.16, to determine the static longitudinal and lateral aerodynamic characteristics of a model of a supersonic-cruise fighter. The configuration, which is designed for efficient cruise at Mach number 1.8, is a twin-engine tailless arrow-wing concept with a single rectangular inlet beneath the fuselage and outboard vertical tails and ventral fins. It had untrimmed values of lift-drage ratio ranging from 10 at subsonic speeds to 6.4 at the design Mach number. The configuration was statically stable both longitudinally and laterally.

Shrout, Barrett L.↗

Flowfield and acoustic properties of a Mach number 0.9 jet at a low Reynolds number

An anechoic vacuum chamber test facility is used to assess the flow field and acoustic properties of a jet with a low Reynolds number of about 3600 and a Mach number of 0.9. A conventional Pitot pressure probe is used to monitor the mean flow field, a hot-wire probe is employed to detect flow fluctuations, and the acoustic field is probed by condenser microphones. The jet is operated at the low Reynolds number in order to examine the behavior of the large-scale 'orderly' structure with particular emphasis on its noise-generating capabilities. It is shown that a nonlinear mechanism involving the large-scale flow instability is responsible for a dominant portion of the noise generated from the jet.

Stromberg, J. L.↗

Flow field and acoustic properties of a Mach number 0.9 jet at a low Reynolds number

An experimental study of the flow field and acoustic properties of a low Reynolds number M = 0.9 jet has been performed in a low pressure anechoic test chamber. The mean flow field was surveyed with a conventional pitot pressure probe and flow fluctuations were detected with a normal hot wire probe. Also, condenser microphone measurements were made in the acoustic field. The flow fluctuations within the jet were found to be dominated initially by a relatively discrete, large-scale, wave-like instability centered around a Strouhal number of 0.44. The axial wavelength of this instability was determined to be 1.45 jet diameters and its azimuthal character includes the n = 0 and n = plus or minus 1 modes. The growth of this instability coupled with its nonlinear breakdown are major contributors to the termination of the potential core region of the jet. The acoustic field of the jet, in contrast to the flow field, has a broad frequency spectrum with a peak amplitude near a Strouhal number of St = 0.2. The results indicate that a nonlinear mechanism involving the large-scale flow instability is responsible for a dominant portion of the noise generated from this jet.

Stromberg, J. L.↗

Flight and wind-tunnel measurements showing base drag reduction provided by a trailing disk for high Reynolds number turbulent flow for subsonic and transonic Mach numbers

The effectiveness of a trailing disk, or trapped vortex concept, in reducing the base drag of a large body of revolution was studied from measurements made both in flight and in a wind tunnel. Pressure data obtained for the flight experiment, and both pressure and force balance data were obtained for the wind tunnel experiment. The flight test also included data obtained from a hemispherical base. The experiment demonstrated the significant base drag reduction capability of the trailing disk to Mach 0.93 and to Reynolds numbers up to 80 times greater than for earlier studies. For the trailing disk data from the flight experiment, the maximum decrease in base drag ranged form 0.08 to 0.07 as Mach number increased from 0.70 to 0.93. Aircraft angles of attack ranged from 3.9 to 6.6 deg for the flight data. For the trailing disk data from the wind tunnel experiment, the maximum decrease in base and total drag ranged from 0.08 to 0.05 for the approximately 0 deg angle of attack data as Mach number increased from 0.30 to 0.82.

Powers, Sheryll Goecke↗

Comparison of experimental and theoretical normal-force distributions (including Reynolds number effects) on an ogive-cylinder body at Mach number 1.98

Effects of Reynolds number and angle of attack on the pressure distribution and normal-force characteristics of a body of revolution consisting of a fineness ratio 3 ogival nose tangent to a cylindrical afterbody 7 diameters long have been determined. The test Mach number was 1.98 and the angle-of-attack range from 0 degree to 20 degrees. The Reynolds numbers, based on body diameter, were 0.15 x 10(6) and 0.45 x 10(6). The experimental results are compared with theory.

Perkins, Edward W↗

Free-flight Performance of 16-inch-diameter Supersonic Ram-jet Units II : Five Units Designed for Combustion-chamber-inlet Mach Number of 0.16 at Free-stream Mach Number of 1.60 (units B-1, B-2, B-3, B-4, and B-5) /c Wesley E. Messing and Scott H. S

Free-flight performance of five 16-inch-diameter ram-jet units was determined over range of free-stream Mach numbers of 0.50 to 1.86 and gas total-temperature ratios between 1.0 and 6.1 Time histories of performance data are presented for each unit. Correlations illustrate effect of free-stream Mach number and gas total-temperature ratio on diffuser total-pressure recovery, net-thrust coefficient, and external drag coefficient. One unit had smooth steady burning throughout the entire flight and encountered a maximum free-stream Mach number of 1.86 with a net acceleration of approximately 4.2 g's.

COMBUSTION - RAM-JET ENGINES↗

Observation of Laminar Flow on a Blunted 15 Degree Cone-cylinder in Free Flight at High Reynolds Numbers and Free-stream Mach Numbers to 8.17

A highly polished 15 degree included-angle cone-cylinder with hemispherical tip has been flown to obtain boundary-layer transition and heat-transfer data. The model was launched from a carrier plane at an altitude of 47,500 feet. Laminar flow existed at a Reynolds number greater than 38.5 x 10(exp) 6 on the cylinder when the model was at the peak free-stream Mach number of 8.17. The results indicate an appreciable and favorable effect of tip bluntness in raising the allowable skin temperature for a given boundary-layer transition Reynolds number.

Disher, John H↗