SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The results of a feasibility study showed that on-orbit commandable lubrication of ball bearings can be accomplished by direct oil application to the moving ball surfaces. Test results for the lubricant applicator portion of the system are presented, in conjunction with a design approach for the reservoir and metering components.
On-orbit commandable lubrication of ball bearings accomplished by direct oil application to the moving ball surfaces was studied. Test results for the lubricant applicator portion of the system are presented in conjunction with a design approach for the reservoir and metering components.
Methane (CH4) emission budgets remain uncertain and are projected to grow as oil and gas production from short-lived wells increases and their subsequent transport through aging gas distribution networks. Orders-of-magnitude variations in temporal, spatial, and emission scales present a key challenge to leak detection and quantification. Also, the probability distributions for large and stochastic, leaky systems such as geological reservoirs (by natural migration-seeps) and petroleum production from those reservoirs remain largely unknown, needed to address current approach limitations. The scale of many petroleum systems favors remote sensing, but the sensitivity of such systems often precludes detection of weak emissions. Consequently, an accurate evaluation requires that the relative contribution from the emission "tails" of small leaks also be quantified, which is best carried out using high-sensitivity in situ methods. Fusion of remote sensing and in situ approaches leverages complementary capabilities to address these limitations. We show results from mobile surface (AMOG) and airborne in situ (AJAX) and thermal-infrared (TIR) hyperspectral imaging spectroscopy (Mako) data applied to a producing oil field in the California Central Valley near Bakersfield. AMOG is an automobile-based mobile lab that measures 13 trace gases, aerosol size distributions and vertical profiles, 3D winds and other meteorology, and atmospheric column measurements by solar spectroscopy at highway speeds. AJAX measures 5 trace gases and 3D winds at ~140 m/s. Mako is a broad-area TIR imaging spectrometer that can discriminate multiple gases present in each pixel acquired. In situ-derived, total field emissions were 31±16 Gg/yr CH4. This was compared with Mako-derived emissions from all plumes identified across the study site. We found that super-emitters were not the dominant emissions mode and the spatial pattern of plume locations from production infrastructure was correlated to geological structures.
In situ systems that provide fresh lubricants to ball/race contacts on demand have been developed to prolong the operational lives of ball bearings. These systems were originally intended to be incorporated into ball bearings in mechanisms that are required to operate in outer space for years, in conditions in which lubricants tend to deteriorate and/or evaporate. These systems may also be useful for similarly prolonging bearing lifetimes on Earth. Reservoirs have been among the means used previously to resupply lubricants. Lubricant- resupply reservoirs are bulky and add complexity to bearing assemblies. In addition, such a reservoir cannot be turned on or off as needed: it supplies lubricant continuously, often leading to an excess of lubricant in the bearing. A lubricator of the present type includes a porous ring cartridge attached to the inner or the outer ring of a ball bearing (see Figure 1). Oil is stored in the porous cartridge and is released by heating the cartridge: Because the thermal expansion of the oil exceeds that of the cartridge, heating causes the ejection of some oil. A metal film can be deposited on a face of the cartridge to serve as an electrical-resistance heater. The heater can be activated in response to a measured increase in torque that signals depletion of oil from the bearing/race contacts. Because the oil has low surface tension and readily wets the bearing-ring material, it spreads over the bearing ring and eventually reaches the ball/race contacts. The Marangoni effect (a surface-tension gradient associated with a temperature gradient) is utilized to enhance the desired transfer of lubricant to the ball/race contacts during heating. For a test, a ball bearing designed for use at low speed was assembled without lubricant and equipped with a porous-ring lubricator, the resistance heater of which consumed a power of less than 1 W when triggered on by a torque-measuring device. In the test, a load of 20 lb (.89 N) was applied and the bearing was turned at a rate of 200 RPM. The lubricator control was turned on at the beginning of the test, turned off for about 800 seconds, then turned on again. As shown in Figure 2, the controlled lubricator stabilized the torque in a low range, starting immediately after initial turn-on and immediately after resumption of the lubricator control.
National awareness of the potential future shortages in energy resources has heightened interest in exploration and utilization of a variety of geothermal energy (GTE) reservoirs. The status of conventional drilling of GTE wells is reviewed briefly and problem areas which lead to higher drilling costs are identified and R and D directions toward solution are suggested. In the immediate future, an expanded program of drilling in GTE formations can benefit from improvements in drilling equipment and technology normally associated with oil or gas wells. Over a longer time period, the new rock-melting drill bits being developed as a part of the Los Alamos Scientific Laboratory's Subterrene Program offer new solutions to a number of problems which frequently hamper GTE drilling, including the most basic problem - high temperature. Two of the most favorable characteristics of rock-melting penetrators are their ability to operate effectively in hot rock and produce glass linings around the hole as an integral part of the drilling process. The technical advantages to be gained by use of rock-melting penetrators are discussed in relation to the basic needs for GTE wells.
A study is presented of the evaluation of the potential geothermal resources of Egypt using a thermal gradient/heat flow technique and a groundwater temperature/chemistry technique. Existing oil well bottom-hole temperature data, as well as subsurface temperature measurements in existing boreholes, were employed for the thermal gradient/heat flow investigation before special thermal gradient holes were drilled. The geographic range of the direct subsurface thermal measurements was extended by employing groundwater temperature and chemistry data. Results show the presence of a regional thermal high along the eastern margin of Egypt with a local thermal anomaly in this zone. It is suggested that the sandstones of the Nubian Formation may be a suitable reservoir for geothermal fluids. These findings indicate that temperatures of 150 C or higher may be found in this reservoir in the Gulf of Suez and Red Sea coastal zones where it lies at a depth of 4 km and deeper.