Search NASA⌕ Search

SEARCH · Search NASA

Results for “Oxide reducibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

High-Sensitivity NO 2 Gas Sensor: Exploiting UV-Enhanced Recovery in a Hexadecafluorinated Iron Phthalocyanine-Reduced Graphene Oxide

Monitoring ultralow nitrogen dioxide (NO 2 ) concentrations is crucial for air quality management and public health. However, the existing NO 2 gas sensors have several defects, like high cost and power consumption, and exhibit poor selectivity. This study addresses these challenges by presenting a novel hexadecafluorinated iron phthalocyanine-reduced graphene oxide (FePcF 16 -rGO) covalent hybrid sensor for NO 2 detection. This innovative approach, which overcomes the limitations of fabrication cost, energy efficiency, and gas selectivity, is a significant step forward in gas sensor technology. The sensor demonstrates exceptional sensitivity toward ultralow NO 2 concentrations (15.14% response for 100 ppb) with a rapid 60 s UV light-induced recovery. Additionally, the sensor exhibits high selectivity for NO 2 , achieving a limit of detection (LOD) of 8.59 ppb. This approach paves the way for developing cost-effective, energy-efficient, and miniature NO 2 monitoring devices for improved environmental monitoring and enhanced safety in workplaces where NO 2 exposure is a concern.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Reduced graphene oxide catalytically enhances the rate of cyanate ester curing under variable frequency microwave heating

Here, the curing of Lonza Primaset PT-30 novolac cyanate ester resin and EPON 826 bisphenol-A diglycidyl ether were investigated using convective thermal heating and variable frequency microwave (VFM) heating. The addition of 1 part per hundred reduced graphene oxide (r-GO) to PT-30 novolac cyanate ester increased the VFM cure rate compared to thermal heating. Curing it at 160°C for 240 min with VFM heating resulted in a 55% degree of cure compared to a 26% degree of cure with thermal heating. This observed VFM rate enhancement is due to selective microwave heating of the r-GO particles in the resin resulting in increased r-GO catalytic activity toward cyanate ester curing. It is both a thermal and catalytic effect, the latter of which is absent when r-GO is added to a bisphenol-A diglycidyl ether resin with o-phenylenediamine hardener. Impurities present in the PT-30 matrix do not appear to contribute to its overall cure kinetics, nor do they participate in the observed VFM rate enhancement.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Porous potassium tantalate-reduced graphene oxide nano cube architecture for high performance hybrid supercapacitors

Energy storage has always been a major concern in the present-day situation. Advanced energy storage devices are batteries, supercapacitor and solar cells. However, advancements have been noteworthy in the field of high-performance hybrid supercapacitors. On this note, we have fabricated a hybrid supercapacitor electrode material Potassium tantalate nano cube (KT NCs) and its reduced graphene oxide composite (KT-rGO NCs) and tested its electrochemical performance. The materials showed high performances with specific capacitance of 565 F/g for KT NCs and 850 F/g for KT-rGO NCs respectively. Energy densities of both KT NCs & KT-rGO NCs are 28.24 Wh/Kg and 29.50 Wh/kg with good retention capacities. Further detailed study of both KT NCs and KT-rGO NCs are carried out with characterization techniques like XRD, FTIR, BET, Raman and HRTEM for structural analysis and electrochemical measurements to analyse various parameters pertaining to its charge storage capacity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Theoretical insights into the surface physics and chemistry of redox-active oxides

Redox active oxides are ubiquitous in materials applications, including catalysis, photovoltaics, self-cleaning glasses, chemical sensors, and electronic components. Their utility derives from their unique ability to access multiple metal charge states within a finite energy window. However, this property also confounds our ability to study reducible oxides, because it leads to structural, compositional, and electronic complexities that elude simplistic models of materials structure and function. Oxygen vacancies play a critical role in shaping the functional properties of such oxides; most notably, they lead to mobile charge imbalances that impact surface processes at significant distances from the originating defect. Atomistic simulations are inherently equipped to illuminate these phenomena at a fundamental level; however, reducible oxides pose great challenges due to the high level of electron correlation needed to correctly describe them. Knowing how defects form, couple, propagate, agglomerate, or repel each other and influence the surface properties of reducible oxides is only now coming into the grasp of modern theory and simulation capabilities. This knowledge is also key to discovering and controlling emergent materials processes at nanometer scale and beyond. The manuscript was written with support of all three authors from U.S. Department of Energy (DOE), Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences. Work by RR and VG was performed at Pacific Northwest National Laboratory (PNNL), which is a multi-program laboratory operated by Battelle for DOE under Contract DE AC05 76RL01830. AS was supported under Award DE-SC0007347.

Rousseau, Roger J.↗
DOE OSTI2022

Remote Floating-Gate Field-Effect Transistor with 2-Dimensional Reduced Graphene Oxide Sensing Layer for Reliable Detection of SARS-CoV-2 Spike Proteins

Despite intensive research of nanomaterials-based field-effect transistors (FETs) as a rapid diagnostic tool, it remains to be seen for FET sensors to be used for clinical applications due to a lack of stability, reliability, reproducibility, and scalability for mass production. In this work, we propose a remote floating-gate (RFG) FET configuration to eliminate device-to-device variations of two-dimensional reduced graphene oxide (rGO) sensing surfaces and most of the instability at the solution interface. Also, critical mechanistic factors behind the electrochemical instability of rGO such as severe drift and hysteresis were identified through extensive studies on rGO–solution interfaces varied by rGO thickness, coverage, and reduction temperature. rGO surfaces in our RFGFET structure displayed a Nernstian response of 54 mV/pH (from pH 2 to 11) with a 90% yield (9 samples out of total 10), coefficient of variation (CV) < 3%, and a low drift rate of 2%, all of which were calculated from the absolute measurement values. As proof-of-concept, we demonstrated highly reliable, reproducible, and label-free detection of spike proteins of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) in a saliva-relevant media with concentrations ranging from 500 fg/mL to 5 μg/mL, with an R 2 value of 0.984 and CV < 3%, and a guaranteed limit of detection at a few pg/mL. Taken together, this new platform may have an immense effect on positioning FET bioelectronics in a clinical setting for detecting SARS-CoV-2.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Scalable aqueous-phase fabrication of reduced graphene oxide nanofiltration membranes by an integrated roll-to-roll (R2R) process

Economic fractionation of multicomponent biomass-derived streams is a key challenge in biobased fuels and chemicals production. Kraft black liquor (BL) is generated at ~1 billion tons/yr globally from biomass pulping and contains ~15wt% total solids including lignin, hemicellulose fragments, and inorganics. Membrane-based BL concentration is attractive but challenged by low solute rejections and poor stability in BL, which combines alkaline pH (~13), high dissolved solids content (15+ wt%) and high temperature (70–85°C). Here we discuss the scaled fabrication and characterization of reduced graphene oxide (rGO) nanofiltration membranes by slot die coating on a roll-to-roll (R2R) with integrated vacuum filtration. Here, we obtain high-quality 90×30 cm rGO membranes (referred to as “R2R-rGO membranes” in this work) with ~100 nm average thickness supported on porous poly(ethersulfone) (PES) sheets, and an effective area of 2700cm 2 . We present characterizations of their microstructure and uniformity as mapped over large areas by scanning electron microscopy (SEM), ellipsometry, adhesion test and X-ray photoelectron spectroscopy (XPS). The constructed ellipsometry model for the rGO membrane/PES substrate composite was successfully applied to 48 different locations of the R2R-rGO membranes. The R2R-rGO membranes showed >98% lignin rejection with a steady state flux of ~12 LMH at 50bar in a 15.7wt% total solids (TS) kraft BL stream at 72°C and 2–3 gal/min crossflow rates. Slot die coating on a R2R platform with integrated vacuum filtration can enable rapid fabrication of high-quality GO membranes at scale without organic solvents or volatile organic compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Transformative Materials for High-Efficiency Thermochemical Production of Solar Fuels (Final Report)

Metal oxide-based two-step solar thermochemical (STC) H 2 O and CO 2 -splitting cycles are a promising route to convert solar thermal energy into fuels. The metal oxide materials are reduced at high temperatures (Step 1), and then at low (but still elevated) temperatures, the reduced oxide is used to split H 2 O or CO 2 (Step 2). However, current applications of these cycles are limited by the efficiency of the metal oxide materials. A lower temperature for reduction is desirable, but that brings a concomitant reduction in the driving force for gas splitting. So, designing novel, high-efficiency materials is challenging. Here, we devised and performed a joint computational-experimental project, combined with materials design strategies and high-throughput approaches with the goal to quickly discover and demonstrate novel thermochemical materials with superior properties. Our approach involves an active feedback loop between experimental and computational research. We have use our previously developed materials design map, to efficiently screen results from high-throughput first- principles computation to predict new compositions and subsequently to experimentally study the properties of novel, predicted materials. Experimental measurements of the thermodynamic properties of selected materials serve as a critical benchmark, not only in evaluating the STCH properties of synthesized compounds, but also serving as a validation dataset for computational approaches. We experimentally explored a set of predicted ABO3 perovskites and focus on obtaining high quality thermodynamic properties for validation of computational prediction of enthalpy and entropy of reduction. These thermodynamic quantities play a major role in designing materials with reduced temperatures of reduction but sufficient gas-splitting rates. Finding good validation between experimental and computational data for enthalpies of reduction, we turn to promising ABO3 materials modified by A and B site substitutions, opening an enormous combinatorial space of materials. We use our high-throughput approach to “tune in” the desired solar thermochemical (STC) properties for STC. This vast composition space can only be reasonably explored using the high-throughput approaches, both computational and experimental, of this proposal. Several promising novel oxide materials have been predicted, synthesized, and verified using our materials design approach.

08 HYDROGEN↗
DOE OSTI2025

Pt Particles on a Dynamic TiO 2 Support in Near-Ambient Conditions−Disentangling Size, Pressure, and Support Effects

Platinum particles on reducible oxides are known to form complex and highly dynamic catalyst systems at elevated pressures and temperatures, often adopting active structures that differ from those found at room temperature and under ultrahigh vacuum (UHV). Here, we study the oxidation and structural evolution of subnanometer Pt clusters and nanoparticles supported on rutile TiO 2 (110) across an oxygen pressure range from UHV to 0.1 mbar, using near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS), scanning tunneling microscopy (STM) under UHV and NAP conditions, and low-energy ion scattering (LEIS). Our results reveal distinct differences in oxidation behavior and thermal stability between Pt nanoparticles and clusters, which are further modulated by the support stoichiometry and oxygen pressure. Small Pt clusters become oxidized even at room temperature but are susceptible to accelerated sintering in 0.1 mbar O 2 at elevated temperatures. In contrast, well-crystallized Pt nanoparticles on near-stoichiometric TiO 2 show weaker oxidation. On a reduced, defective TiO 2 support, Pt instead quickly becomes deeply buried by new titania layers, which are formed during support reoxidation. This process appears to result primarily from interactions of the support with the gas phase, unlike the classical, selflimited encapsulation that is induced by the strong metal−support interaction (SMSI). Finally, we address the full complexity of real catalysts in a direct side-by-side comparison of the single-crystalline model system with a Pt-loaded TiO 2 powder catalyst (P25). We conclude that the stoichiometry of the model supports must be carefully chosen and controlled to accurately reproduce the expected state of powder supports during redox reactions.

metal nanoparticles↗
DOE OSTI2021

Investigation of the NO reduction by CO reaction over oxidized and reduced NiO x /CeO 2 catalysts

CeO 2 -supported NiO x catalysts have been widely studied in various catalytic reactions including NO reduction by CO. This work is mainly focused on investigation of the impact of catalyst synthesis conditions (e.g., oxidation and reduction) on the physicochemical properties of NiO x /CeO 2 catalysts and the catalytic response for the NO reduction by CO reaction. The oxide NiO x /CeO 2 sample was prepared by an incipient wetness impregnation (IWI) method and reduced under hydrogen reduction treatment at high temperatures (500 and 700 °C). The physicochemical properties of the synthesized samples were characterized by BET analysis, Raman spectroscopy, XRD, XPS, EELS and high-resolution transmission electron microscopy (HR-TEM). The results showed that higher reduction temperature led to the decrease in specific surface area (SSA), fewer oxygen vacancy/defect site, larger crystallite size of the CeO 2 support, and formation of metallic Ni on the surface. The oxidized NiO x /CeO 2 catalyst showed the highest catalytic activity, indicating that the presence of oxygen vacancy/defect sites, Ni 2+ oxidation state, and smaller crystallite size are believed to enhance the catalytic activity. In situ DRIFTS confirmed the generation of several intermediate species, such as nitrate, carbonate, and N 2 O. Finally, on the basis of in situ DRIFTS and activity results, the possible reaction mechanism of NO reduction by CO over NiO x /CeO 2 was proposed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Structure–property relationships of reduced graphene oxide membranes intercalated with polycyclic aromatics

Graphene oxide (GO) membranes intercalated with various organic moieties have shown excellent potential for a range of water processing applications. However, microstructure–functional property relationships in these structurally disordered membranes are not well understood. We demonstrate a practical methodology for developing such relationships for GO membranes intercalated with molecular species, with polycyclic aromatic toluidine blue O (TBO) as an example functional intercalant. We use solid-state UV–vis absorbance and fluorescence measurements to quantitatively track the arrangements of TBO in a series of TBO-loaded reduced GO (rGO) membranes. This study reveals the evolution of diverse arrangements including TBO monomers, lateral and stacked dimers, and other aggregates, as a function of overall TBO loading. These microstructures are then correlated to changes in overall properties such as interlayer d-spacings, permeate fluxes, and solute rejections. The characterization of these different intercalant microstructures explains non-intuitive flux and rejection trends, which can circumvent flux and solute rejection trade-offs.

02 PETROLEUM↗