Search NASA⌕ Search

SEARCH · Search NASA

Results for “PEC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Cost-constrained adaptive simulations of transient spray combustion in a gas turbine combustor

Predictive high-fidelity simulations of turbulent spray combustion must capture the combined effects of complex chemistry, multiphase evaporating flow and spray-flame interactions to achieve physical accuracy. Finite-rate chemistry (FRC) combined with a realistic chemical mechanism is a combustion model well-suited for this purpose, but has a high computational cost due to the large number and stiffness of transported chemical species. In contrast, flamelet-based models achieve lower cost by transporting a small number of quantities of reduced stiffness, but assumptions regarding local flame topology, boundary conditions and inter-phase coupling limit their physical accuracy. Recently, the Pareto-efficient combustion (PEC) framework was developed to dynamically assign combustion models based on local cost and accuracy metrics in gas-phase reacting flows. In this work, we extend this PEC framework to spray combustion through the rigorous analysis of the multiphase coupling terms in the governing equations. The derivation shows that spray evaporation causes errors in the prediction of species mass fractions for flamelet-based models due to the sensitivity of the local thermo-chemical state to changes in composition caused by fuel vaporization across combustion regimes present in practical spray combustion devices. Sub-model assignment is formulated as a multiple-choice knapsack problem, where computational cost is directly controlled through the fraction of the domain assigned to the FRC sub-model. The extended PEC formulation is applied to the simulation of a realistic rich-quench-lean gas turbine combustor at steady-state conditions, as well as transient operation resulting in lean blow-out (LBO). Analysis of transient simulations during LBO demonstrates the extended PEC formulation’s capacity to dynamically adapt to changing conditions within the combustor. Transient combustor dynamics are shown to approach convergence with limited increases in computational cost, while retaining substantial computational cost reduction compared to monolithic FRC simulations. Through PEC simulations with increasing fractions of the domain assigned to FRC, monolithic flamelet simulations are shown to over-predict flame stability during LBO. Finally, the extended PEC formulation is thus shown to overcome deficiencies of monolithic models by controlling modeling error for multiphase combustion modeling.

33 ADVANCED PROPULSION SYSTEMS↗

Engineering Surface Architectures for Improved Durability in III–V Photocathodes

GaInP2 has shown promise as the wide bandgap top junction in tandem absorber photoelectrochemical (PEC) water splitting devices. Among previously reported dual-junction PEC devices with a GaInP 2 top cell, those with the highest performance incorporate an AlInP 2 window layer (WL) to reduce surface recombination and a thin GaInP2 capping layer (CL) to protect the WL from corrosion in electrolytes. However, the stability of these III-V systems is limited, and durability continues to be a major challenge broadly in the field of PEC water splitting. This work provides a systematic investigation into the durability of GaInP 2 systems, examining the impacts of the window layer and capping layer among single junction pn-GaInP 2 photocathodes coated with an MoS 2 catalytic and protective layer. The photocathode with both a CL and WL demonstrates the highest PEC performance and longest lifetime, producing a significant current for >125 h. In situ optical imaging and post-test characterization illustrate the progression of macroscopic degradation and chemical state. The surface architecture combining an MoS 2 catalyst, CL, and WL can be translated to dual-junction PEC devices with GaInP 2 or other III-V top junctions to enable more efficient and stable PEC systems.

08 HYDROGEN↗

Ir–Ru Particles Enable Low-Loading Acidic Oxygen Evolution for Integrated Solar Devices

Integrated photoelectrochemical (PEC) devices for water splitting represent a compelling pathway for sustainable hydrogen production, directly converting solar energy into chemical fuels. While alkaline systems have achieved state-of-the-art solar-to-hydrogen (STH) efficiencies above 20% using earth-abundant catalysts, acidic PEC architectures provide unique advantages for compact device integration, fast proton transport, and stable operation under highly dynamic solar conditions. Proton-exchange membrane (PEM)-based configurations enable high current densities, low gas crossover, and rapid ionic response, making them especially well-suited for intermittent, bias-free PEC operation, despite alkaline electrolysis being more technologically mature. A critical limitation of acidic PEC systems remains, the oxygen evolution reaction (OER), which currently relies on scarce and costly iridium catalysts, restricting scalability. Here, in this study, we report a series of low-iridium mixed-metal oxide catalysts synthesized via a surfactant-assisted borohydride reduction method. An optimized Ir 0.5 Ru 0.5 O x catalyst exhibits exceptional intrinsic activity (>400 A g –1 Ir at 1.55 V vs RHE) in 0.1 M HClO 4 and maintains stable operation for over 10 days in an integrated PEC flow-cell. Sustained hydrogen production is achieved at 1.65 V with a total iridium loading of only 0.1 mg cm –2 , substantially below commercial PEM benchmarks. These results demonstrate a viable pathway toward scalable, high-performance acidic PEC hydrogen technologies.

Acidic electrolysis↗

An auxiliary-field quantum Monte Carlo study of the chromium dimer

The chromium dimer (Cr{sub 2}) presents an outstanding challenge for many-body electronic structure methods. Its complicated nature of binding, with a formal sextuple bond and an unusual potential energy curve (PEC), is emblematic of the competing tendencies and delicate balance found in many strongly correlated materials. We present an accurate calculation of the PEC and ground state properties of Cr{sub 2}, using the auxiliary-field quantum Monte Carlo (AFQMC) method. Unconstrained, exact AFQMC calculations are first carried out for a medium-sized but realistic basis set. Elimination of the remaining finite-basis errors and extrapolation to the complete basis set limit are then achieved with a combination of phaseless and exact AFQMC calculations. Final results for the PEC and spectroscopic constants are in excellent agreement with experiment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Deadband Voltage Control and Power Buffering for Extreme Fast Charging Station

Voltage fluctuation is one of the most common challenges that electric vehicle charging station (EVCS) may introduce to the power grid. Local reactive power compensation (Q-compensation) capability of bi-directional electric vehicle (EV) chargers can mitigate the steady-state voltage violations caused by the EV charging itself or changes in the neighboring loads. Power buffering, using energy storage system (ESS), can be utilized to address the voltage transients (sags and swells) as a result of EV charging at the EVCS. To address PI controller’s ‘hunting’ issue, this paper proposes a Q-sign triggered deadband voltage control (V-control) method at the point of common coupling (PCC). In addition, to ensure the ramp rate of EV charging is within the allowable limits set forth by the grid code, a ramp rate control is proposed that uses the ESS as a ‘power buffer’. Lastly, different from most reported work in the literature where no explicit limit of the power electronic converters (PECs) is considered, this work considers a reasonable apparent power capacity limit of the PECs when achieving the V-control. This limit also affects the amount of active power that can be obtained from the grid, and subsequently may require ESS to function as ‘load sharing’ device to provide supplemental active power to satisfy EV load. A case study simulated in MATLAB (interfaced with PLECS) is presented to demonstrate the effectiveness of the proposed approaches for EVCS operation.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Novel Chalcopyrites for Advanced Photoelectrochemical Water Splitting

With the support of DoE’s EERE office, our team has established a unique tool-chest of capabilities, including theoretical modeling (Lawrence Livermore National Laboratory: LLNL), state-of-the-art synthesis (Hawaii Natural Energy Institute: HNEI, Stanford, and the National Renewable Energy Laboratory: NREL) and advanced materials and interfaces characterization (University of Nevada, Las Vegas: UNLV, and Lawrence Berkeley National Laboratory: LBNL), to accelerate the development of high efficiency and durable chalcopyrite materials for advanced photoelectrochemical (PEC) water splitting. Using this synergistic approach, we have successfully created new wide bandgap chalcopyrite photocathodes generating over 10 mA/cm 2 , developed innovative strategies to protect them from corrosion, and engineered novel integration methods to circumvent thin film materials mechanical, chemical and thermal incompatibility. In Task 1 “Modeling and synthesis of chalcopyrite photocathodes”, we expanded our library of wide bandgap chalcopyrites for PEC water splitting. With support from LLNL’s “Computational Materials Diagnostics and Optimization of PEC Devices”, LBNL’s “photophysical” and NREL’s “I-III-VI Compound Semiconductors for Water-Splitting” nodes, we investigated two new chalcopyrite candidates for PEC water splitting: Cu(In,Al)Se 2 and Cu(In,B)Se 2 . We also further developed ordered vacancy compounds, such as CuGa 3 Se 5 , with unprecedented durability during PEC waters splitting in acidic solutions. In Task 2 “Interfaces engineering for enhanced efficiency and durability”, we addressed both the non-ideal band-edge positions of chalcopyrites with respect to water redox potentials, as well as their chemical instability under PEC water splitting, with a buried-junctions approach. With help from NREL’s “High-Throughput Experimental Thin Film Combinatorial Capabilities” and “Corrosion Analysis of Materials” nodes, we engineered environmentally friendly n-type buffers, including Mn x Zn 1-x O, to adjust the chalcopyrite band-edge positions and achieved photovoltages as high as 925 mV. Also, we integrated non-precious catalytic-protecting layers, such as WO 3 , to enhance the water splitting long-term stability of chalcopyrite absorbers. Finally, in Task 3 “Hybrid photoelectrode device integration”, we proposed an innovative method to bond wide bandgap photocathodes onto narrow bandgap PV drivers at room temperature using conductive polymers. Our semi-monolithic approach addressed fundamental processing incompatibility issues, as both the photocathode and the PV driver are processed separately. Proof-of-concept whole-chalcopyrite tandems were obtained by consecutive exfoliation and transfer of fully integrated 1.85 eV CuGa 3 Se 5 and 1.13 eV CuInGaSe 2 stacks from their Mo/SLG substrates onto a new single FTO host substrate.

08 HYDROGEN↗

Development of Polycrystalline Photoelectrodes with Optimum Compositions and Morphologies for Solar Fuel Production via Electrochemical Synthesis (Final Technical Report)

Photoelectrochemical cells (PECs) can utilize solar energy for water splitting to produce H 2 as a clean fuel. The most critical components of a water-splitting PEC are semiconductor electrodes (photoelectrodes) that absorb solar energy to generate photoexcited charge carriers and transport them to the electrode/electrolyte interface for water reduction and oxidation reactions. While efficient PEC hydrogen production has been successfully demonstrated on the laboratory scale, the commercial viability of PECs depends critically on the cost of H 2 produced by the PECs, which is affected by the cost of PEC construction. Therefore, identifying promising inexpensive semiconductor electrodes is important. The goal of this project was to bring an advancement in the synthesis and understanding of inexpensive polycrystalline photoelectrodes based on oxides. Oxide-based semiconductors are inexpensive, easy to fabricate, and relatively more stable in aqueous media compared to other types of semiconductors. This project developed new electrodeposition methods to produce a variety of oxide-based semiconductor electrodes with precisely controlled compositions and morphologies to enhance photon absorption, electron-hole separation, and the use of electrons and holes for desired chemical reactions. The resulting high-quality photoelectrodes were investigated to establish the structure-composition-morphology-photoelectrochemical property relationships to identify the advantages and limitations of each oxide semiconductor system.

14 SOLAR ENERGY↗

Some Activities of MISSE 6 Mission

The objective of the Materials International Space Station Experiment (MISSE) is to study the performance of novel materials when subjected to the synergistic effects of the harsh space environment for several months. In this paper, a few laser and optical elements from NASA Langley Research Center (LaRC) that have been flown on MISSE 6 mission will be discussed. These items were characterized and packed inside a ruggedized Passive Experiment Container (PEC) that resembles a suitcase. The PEC was tested for survivability due to launch conditions. Subsequently, the MISSE 6 PEC was transported by the STS-123 mission to International Space Station (ISS) on March 11, 2008. The astronauts successfully attached the PEC to external handrails and opened the PEC for long term exposure to the space environment. The plan is to retrieve the MISSE 6 PEC by STS-128 mission in August 2009.

Prasad, Narasimha S.↗

Redesigning Photoelectrodes So They Can Work in the Light and Dark

Unassisted photoelectrochemical (PEC) reactions, such as H2 generation and CO2 reduction, are limited by the durability of the immersed photoelectrode. Small band gap semiconductors, like Si, are efficient at utilizing a large portion of the solar spectrum but are not stable in aqueous environments without protection. While great strides have been made to improve stability under constant illumination, dark stability remains relatively unexamined and presents great challenges for durable PEC systems. Cathodic protection is an established electrochemical method for preventing metal electrode degradation in harsh conditions. Similar protection strategies cannot be applied to traditional two-terminal (2T) semiconductor photoelectrodes because of their inability to pass reverse bias current in the dark. New, three-terminal (3T) photovoltaic (PV) architectures introduce additional degrees of freedom in traditional 2T PEC operations by adding an extra electrical contact for an alternative low resistance path to protect the photoelectrode and drive electrochemical reactions, even in the dark. Here, we investigate bare 3T Si PV devices operating as photocathodes in aqueous methyl viologen electrolyte. The 3T architecture provides additional capabilities to PEC systems such as cathodic protection, the ability to drive reactions with or without illumination, and in situ switching between different operational modes. We show that 3T-based Si photocathodes maintain PEC activity after several hours of light/dark cycling. This work helps advance PEC use in real-world conditions where variable illumination must be considered.

cathodic protection↗

Analysis of AC-DC Converters for Grid-tied High Temperature Steam Electrolysis Systems

Grid-tied HTSE systems have the prospects to produce clean hydrogen enabling power and broad energy systems decarbonization. Most commercially available power electronic converter systems (PECS) are designed for batteries, solar PVs, wind, and other well-established renewable energy resources. Standards (such as IEEE 1547, UL 1741, CA Rule-21, HI Rule-14) exist for PECS used for renewable energy systems such as battery storage and solar PVs. However, those that consider the dynamic behavior of HTSEs and that can be used for large-scale H2 systems are yet to be developed. This paper investigates the performance of these PECS for the HTSE application that are set up at the Idaho National Laboratory for hydrogen production testing, research and development. In particular, the performance analysis of two grid-tied PECS (A and B) is conducted for a 100 kW solid oxide HTSE system. System A consists of 6 units of 30kW MOSFET-switched bidirectional AC-DC rectifier while system B has a single unit of 150kW thyristor-switched ACDC rectifier. Both systems are connected to the HTSE stacks via a DC-DC converter. Different operational conditions of the HTSE system are tested to analyze the dynamic response of the HTSE’s PECS. The experimental results show the need to develop advanced control strategies for PECS that incorporates the dynamics of HTSE systems for improved performance.

08 - HYDROGEN↗

Analysis of AC-DC Converters for Grid-tied High Temperature Steam Electrolysis Systems

Grid-tied HTSE systems have the prospects to produce clean hydrogen enabling power and broad energy systems decarbonization. Most commercially available power electronic converter systems (PECS) are designed for batteries, solar PVs, wind, and other well-established renewable energy resources. Standards (such as IEEE 1547, UL 1741, CA Rule-21, HI Rule14) exist for PECS used for renewable energy systems such as battery storage and solar PVs. However, those that consider the dynamic behavior of HTSEs and that can be used for large-scale H2 systems are yet to be developed. This paper investigates the performance of these PECS for the HTSE application that are set up at the Idaho National Laboratory for hydrogen production testing, research and development. In particular, the performance analysis of two grid-tied PECS (A and B) is conducted for a 100 kW solid oxide HTSE system. System A consists of 6 units of 30kW MOSFET-switched bidirectional AC-DC rectifier while system B has a single unit of 150kW thyristor-switched AC-DC rectifier. Both systems are connected to the HTSE stacks via a DC-DC converter. Different operational conditions of the HTSE system are tested to analyze the dynamic response of the HTSE’s PECS. The experimental results show the need to develop advanced control strategies for PECS that incorporates the dynamics of HTSE systems for improved performance.

High temperature steam electrolysis↗

Radioactive Material Inventory Optimization Using the Plutonium-239 Equivalent Curie Methodology

ABSTRACT The purpose of this paper is to provide the technical basis for application of the Plutonium 239 equivalent curies (PEC) concept used to optimize and limit the material-at-risk (MAR) in the Irradiated Materials Characterization Laboratory (IMCL) located at the Materials and Fuels Complex (MFC). The PEC concept offers a method to normalize all radionuclides to a common radiotoxic hazard index that can be summed to a single value. This paper describes the technical approach to applying the PEC concept, documents the weighting factors and specific activities to be utilized in the calculation, and provides an example of the application of the concept to a radionuclide distribution that is representative of materials encountered in the IMCL. The IMCL is operated to provide a dynamic, re-configurable capability to analyze and characterize irradiated or non-irradiated radioactive material samples. The operations unique to the IMCL include sample storage, preparation, and analysis using experiment-specific instrumentation such as, Electron probe micro-analyzer (EPMA), Focused ion beam (FIB), Transmission electron microscope (TEM), and Scanning electron microscope (SEM). The methodology used to characterize the radioactive material inventory enables the IMCL to operate in such a way that complements their capability and program goals without compromising the safety of the worker, co-located worker, or the general public. The PEC concept offers a method in which all radionuclide inventory is normalized to a common radiotoxic hazard index that can be summed to a single value. The PEC concept is useful in the comparison of various material types for hazard categorization and for identifying worst-case and bounding inventory.

07 ISOTOPE AND RADIATION SOURCES↗

Production of Hydrogen for Clean and Renewable Source of Energy for Fuel Cell Vehicles

This was a two-year project that had two major components: 1) the demonstration of a PV-electrolysis system that has separate PV system and electrolysis unit and the hydrogen generated is to be used to power a fuel cell based vehicle; 2) the development of technologies for generation of hydrogen through photoelectrochemical process and bio-mass derived resources. Development under this project could lead to the achievement of DOE technical target related to PEC hydrogen production at low cost. The PEC part of the project is focused on the development of photoelectrochemical hydrogen generation devices and systems using thin-film silicon based solar cells. Two approaches are taken for the development of efficient and durable photoelectrochemical cells; 1) An immersion-type photoelectrochemical cells (Task 3) where the photoelectrode is immersed in electrolyte, and 2) A substrate-type photoelectrochemical cell (Task 2) where the photoelectrode is not in direct contact with electrolyte. Four tasks are being carried out: Task 1: Design and analysis of DC voltage regulation system for direct PV-to-electrolyzer power feed Task 2: Development of advanced materials for substrate-type PEC cells Task 3: Development of advanced materials for immersion-type PEC cells Task 4: Hydrogen production through conversion of biomass-derived wastes

08 HYDROGEN↗

Coupling Interfacial Redox‐Reactions with In Situ Proton Generation for the Photoelectrochemical Separation of Rare‐Earth Elements

Abstract A dual‐function photoelectrochemical (PEC) separation system is demonstrated for rare‐earth element (REE) recovery. The sustainable release of the captured REEs is promoted through the synergistic integration of a redox‐reaction for electrostatic repulsion, and in situ proton generation for ion‐exchange, all driven by photoelectrochemistry. The platform consists of a redox‐copolymer, poly(ferrocenylpropyl methacrylamide‐ co ‐methacrylic acid) (P(FPMAm‐ co ‐MAA)) (PFM), conjugated with carbon nanotubes (CNTs) and coated onto titanium dioxide nanorods (TNRs). The (PFM‐CNT)/TNR spontaneously adsorbs up to 214.2 mg of Yttrium/g PFM by ion‐exchange, and demonstrates broad applicability for other REEs. The adsorbed REEs are released through the PEC oxidation of ferrocene (Fc) to ferrocenium (Fc + ), and the simultaneous PEC water splitting reactions at the TNRs that protonate the carboxylate binding groups. This dual photoelectrochemically‐driven mechanism for REE release is investigated by in situ pH measurements, as well as vibrational and X‐ray photoelectron spectroscopy. Through PEC approaches, a 68.8% reduction in energy consumption during REE recovery has been achieved compared to purely electrochemical systems, with a regeneration efficiency close to 100%. For NdFeB magnets from waste hard disk drives, Nd and Dy recovery efficiencies of 59.2 and 61.1% are achieved. The dual‐functionality of these copolymer PEC systems offers a sustainable platform for modulating critical element recovery.

Cho, Ki‐Hyun [Department of Chemical and Biomolecu↗

Light‐Driven BiVO 4 –C Fuel Cell with Simultaneous Production of H 2 O 2

Abstract Photoelectrochemical (PEC) systems have been researched for decades due to their great promise to convert sunlight to fuels. The majority of the research on PEC has been using light to split water to hydrogen and oxygen, and its performance is limited by the need of additional bias. Another research direction on PEC using light, is to decompose organic materials while producing electricity. In this work, the authors report a new type of unassisted PEC system that uses light, water and oxygen to simultaneously produce electricity and hydrogen peroxide (H 2 O 2 ) on both the photoanode and cathode, which is essentially a light‐driven fuel cell with H 2 O 2 as the main product at the two electrodes, meanwhile achieving a maximum power density of 0.194 mW cm ‐2 , an open circuit voltage of 0.61 V, and a short circuit current density of 1.09 mA cm ‐2 . The electricity output can be further used as a sign for cell function when accompanied by a detector such as a light‐emitting diode (LED) light or a multimeter. This is the first work that shows H 2 O 2 two‐side generation with a strict key factors study of the system, with a clear demonstration of electricity output ability using low‐cost earth abundant materials on both sides, which represents an exciting new direction for PEC systems.

Shi, Xinjian↗

Effects of annealing temperature on the physicochemical, optical and photoelectrochemical properties of nanostructured hematite thin films prepared via electrodeposition method

Highlights: • Nanostructured hematite thin films were synthesized via electrodeposition method. • Effects of annealing on size, grain boundary and PEC properties were examined. • Photocurrents generation was enhanced when the thin films were annealed at 600 °C. • The highest photocurrent density of 1.6 mA/cm{sup 2} at 0.6 V vs Ag/AgCl was achieved. - Abstract: Hematite (α-Fe{sub 2}O{sub 3}) is a promising photoanode material for hydrogen production from photoelectrochemical (PEC) water splitting due to its wide abundance, narrow band-gap energy, efficient light absorption and high chemical stability under aqueous environment. The key challenge to the wider utilisation of nanostructured hematite-based photoanode in PEC water splitting, however, is limited by its low photo-assisted water oxidation caused by large overpotential in the nominal range of 0.5–0.6 V. The main aim of this study was to enhance the performance of hematite for photo-assisted water oxidation by optimising the annealing temperature used during the synthesis of nanostructured hematite thin films on fluorine-doped tin oxide (FTO)-based photoanodes prepared via the cathodic electrodeposition method. The resultant nanostructured hematite thin films were characterised using field emission-scanning electron microscopy (FE-SEM) coupled with energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), UV-visible spectroscopy and Fourier transform infrared spectroscopy (FTIR) for their elemental composition, average nanocrystallites size and morphology; phase and crystallinity; UV-absorptivity and band gap energy; and the functional groups, respectively. Results showed that the nanostructured hematite thin films possess good ordered nanocrystallites array and high crystallinity after annealing treatment at 400–600 °C. FE-SEM images illustrated an increase in the average hematite nanocrystallites size from 65 nm to 95 nm when the annealing temperature was varied from 400 °C to 600 °C. As the crystallites size increases, the grain boundaries reduce and this suppresses the recombination rate of electron–hole pairs on the nanostructured hematite thin films. As a result, the measured photocurrent densities of nanostructured hematite thin films also increased. The highest measured photocurrent density of 1.6 mA/cm{sup 2} at 0.6 V vs Ag/AgCl in 1 M NaOH electrolyte was achieved for the nanostructured hematite thin film annealed at 600 °C. This study had confirmed that strong interdependencies exist between the average hematite nanocrystallites size and grain boundaries with annealing temperature on the eventual PEC water splitting performance of nanostructured hematite thin films. The annealed hematite thin films at a higher temperature will enhance the nanocrystals growth and thus, suppressing the electron–hole pairs recombination rate, lowering the grain boundary resistance and enabling higher photocurrent flow at the molecular level. As a result, the photocurrent density and thus, the overall PEC water splitting performance of the nanostructured hematite thin films are significantly enhanced.

36 MATERIALS SCIENCE↗

Improved Stability and Performance of Visible Photoelectrochemical Water Splitting on Solution-Processed Organic Semiconductor Thin Films by Ultrathin Metal Oxide Passivation

Solution-processable organic semiconductors have potentials as visible photoelectrochemical (PEC) water splitting photoelectrodes due to their tunable small band gap and electronic energy levels, but they are typically limited by poor stability and photocatalytic activity. In this study, we demonstrate the direct visible PEC water oxidation on solution-processed organic semiconductor thin films with improved stability and performance by ultrathin metal oxide passivation layers. N-type fullerene-derivative thin films passivated by sub-2 nm ZnO via atomic layer deposition enabled the visible PEC water oxidation at wavelengths longer than 600 nm in harsh alkaline electrolyte environments with up to 30 μA/cm 2 photocurrents at the thermodynamic water-oxidation equilibrium potential and the photoanode half-lifetime extended to ~1000 s. The systematic investigation reveals the enhanced water oxidation catalytic activity afforded by ZnO passivation and the charge tunneling governing the hole transfer through passivation layers. Further enhanced PEC performances were realized by improving the bottom ohmic contact to the organic semiconductor, achieving ~60 μA/cm 2 water oxidation photocurrent at the equilibrium potential, the highest values reported for organic semiconductor thin films to our knowledge. The improved stability and performance of passivated organic photoelectrodes and discovered design rationales provide useful guidelines for realizing the stable visible solar PEC water splitting based on organic semiconductor thin films.

14 SOLAR ENERGY↗

Strong O 2p–Fe 3d Hybridization Observed in Solution-Grown Hematite Films by Soft X-ray Spectroscopies

Photoelectrochemical (PEC) water splitting holds the potential as a direct route for solar energy conversation and storage. The performance of a PEC device is strongly influenced by the electronic properties of the photonanode surface. It has been shown that the synthesis methods can have a profound impact on the electronic properties and PEC performance of various photoelectrode materials such as hematite. Soft X-ray spectroscopic techniques, including O K-edge XAS and Fe L-edge XAS/XES, have been employed to investigate how the synthesis methods impact the electronic structure of resulting hematite materials. It is found that the hematite samples via solution regrowth methods show dramatically increased 3d-4sp band ratios in O K-edge XAS spectra and decreased relative elastic peak intensities in Fe L-edge RIXS spectra compared with samples synthesized via ALD or solution grown. The difference observed in O-K and Fe-L spectra indicated that solution regrowth strategy alters the O 2p-Fe 3d hybridization and hence the electronic structure of the hematite films, which proves to be beneficial for PEC performance of the hematite photoanode. Our findings provided new insights and potentially useful strategies for enhancing the PEC performance of photoanode materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗