SEARCH · Search NASA

Results for “PROPAGATION MODE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1990

The magnetoionic modes and propagation properties of auroral radio emissions

The nature of the magnetoionic wave modes which accompany the aurora is clarified here by a detailed analysis, using multiple techniques, of DE 1 auroral radio observations. All four of the possible magnetoionic wave modes are found to occur, apparently emitted from two different source regions on the same auroral field line. AKR originates primarily in the X mode near the electron cyclotron frequency, and is frequently also accompanied by a weaker O-mode component from the same location. The next most prominent auroral emission is the W-mode auroral hiss originating from altitudes always well below the DE 1 satellite at frequencies below the local cyclotron frequency. The previously reported Z-mode auroral radiation was also detected, but from sources also below the satellite at the poleward edge of the cavity, and not from the expected AKR source at the cyclotron frequency.

Calvert, Wynne↗

NASA NTRS1993

Measurement of p-mode energy propagation in the quiet solar photosphere

We have measured and analyzed the p-mode oscillations in the profile of the Mg I 4571 A line in a quiet region near disk center. The oscillations are found to be mostly standing waves, in agreement with previous work. However, a small propagating component is measured, and we determine the direction, magnitude, and vertical variation of the energy propagation. The work integral indicates an upward energy flow of about 2 x 10 exp 7 ergs/sq cm/s at a height of 50 km above the base of the photosphere for waves with frequencies of 2-16 mHz. This energy flow decreases exponentially with height and drops below 10 exp 5 ergs/sq cm/s in the uppermost photosphere. The energy flow leaving the upper photosphere is at least an order of magnitude too small to constitute a significant source of heating for the chromosphere. However, the p-mode damping in the lower photosphere approaches levels large enough to account for the measured p-mode line widths. The relative amplitudes and phases of the thermodynamic quantities indicate that the p-mode are neither adiabatic nor isothermal in the photosphere.

Fontenla, J. M.↗

NASA NTRS1981

Whistler mode wave propagation in the solar wind near the bow shock

The presence of whistler mode waves in, and upstream from, the bow shock has been well established by observation. Theoretical descriptions of the mode under solar wind conditions have been relatively meagre, however, and it may not be generally appreciated how readily whistler waves generated in the shock could occupy most of the region ahead of the shock most of the time. Graphic descriptions of phase and group velocities and group velocity directions for typical solar wind parameters are presented by using the cold plasma approximation over all appropriate frequencies and directions with respect to the IMF. The relations of whistler phase and group velocities to observations of a quasi-perpendicular shock crossing by ISEE are illustrated.

Greenstadt, E. W.↗

NASA NTRS1975

Acoustic systems containing curved duct sections

The analysis of waves in bends in acoustical ducting of rectangular cross section is extended to the study of motion near discontinuities. This includes determination of the characteristics of the tangential and radial components of the non-propagating modes. It is established that attenuation of the non-propagating modes strongly depends on frequency and that, in general, the sharper the bend, the less attenuation may be expected. Evaluation of a bend's impedance and of impedance-generated reflections is also presented in detail.

Rostafinski, W.↗

NASA NTRS1973

Radiated sound field measurements from an annular flow duct facility

A series of measured radiated field patterns correlated with defined in-duct conditions is presented, along with a second series of radiation measurements for multiple mode propagation, with individual mode amplitudes and phases at duct termination as well as with angular positions of higher-order stationary duct modes relative to the plane of the radiated field measurement. Though incomplete, these experimental data should prove useful for comparisons with theoretical predictions in testing analytical procedures and prediction techniques.

Plumblee, H. E.↗

NASA NTRS1983

Ordinary mode auroral kilometric radiation, with harmonics, observed by ISIS 1

Topside-sounder receiver observations by ISIS 1 that reveal examples of o-mode auroral kilometric radiation (AKR) are presented. They correspond to locations outside of the low density source region of intense AKR x-mode emission. The propagation modes are identified by comparing the natural radiation wave cutoffs with the local resonant and wave cutoff phenomena stimulated by the sounder transmitter. The o-mode AKR is the dominant emission in these regions of relatively high electron density, but it is considerably weaker than the intense x-mode AKR observed to emanate from low density cavities above the auroral regions. In addition to the fundamental o-mode, 2nd and 3rd harmonic bands of radiation have also been detected. Harmonics associated with these o-mode AKR are less intense than the harmonics associated with x-mode AKR. It is difficult to explain the variety of harmonic AKR observations (x as well as o-mode) based on present AKR theories.

Benson, R. F.↗

NASA NTRS1984

Ordinary mode auroral kilometric radiation, with harmonics, observed by ISIS 1

Benson, R. F.↗

NASA NTRS2003

Passive Fetal Heart Monitoring System

A fetal heart monitoring system and method for detecting and processing acoustic fetal heart signals transmitted by different signal transmission modes. One signal transmission mode, the direct contact mode, occurs in a first frequency band when the fetus is in direct contact with the maternal abdominal wall. Another signal transmission mode, the fluid propagation mode, occurs in a second frequency band when the fetus is in a recessed position with no direct contact with the maternal abdominal wall. The second frequency band is relatively higher than the first frequency band. The fetal heart monitoring system and method detect and process acoustic fetal heart signals that are in the first frequency band and in the second frequency band.

Zuckerwar, Allan J.↗

NASA NTRS1995

Integrated optical components in thin films of polymers

The results will be reported on the study of integrated optical components based on nonlinear optical polymeric films. Polymers poly(methyl methacrylate) (PMMA) and polyimide (PI) doped with organic laser dyes 4-dicyanomethylene-2-methyl-6-p dimethylaminostyryl-4H pyran (DCM) and 1, 3, 5, 7, 8 - pentamethyl-2,6 -diethyl-pyrromethene -BF2-complex (Pyrommethene 567, PM-567) were selected as materials for light guiding films. Additionally, UV polymerized polydiacetylene (PDA) on glass substrate was used as a waveguide material. Optical waveguides were fabricated using spin coating of preoxidized silicon wafers (1.5 micrometer silicon oxide layer) with organic dye/polymer solution followed by soft baking. the modes in slab waveguides were studied using prism coupling techniques. Measured values of mode coupling angles in multimode waveguides were used to calculate film thickness and refractive index for different polarizations. Refractive index anisotropy was found in PDA waveguide. The optimal conditions of spin coating for single mode waveguide fabrication were estimated. Propagation losses were measured by collecting the light scattered from the trace of a propagating mode either by scanning photo detector or by CCD camera. Different types of light coupling techniques were used including end-dire coupling, prism and grating coupling. Mechanical printing technique was developed for coupling grating fabrication resulting in gratings with 4% diffraction efficiency. The gratings demonstrated good stability with diffraction efficiency relaxation rate 2.4 dB/hour at a temperature approximately 15-20 C below glass transition point. Dye doped waveguides were transversally pumped with frequency doubled Nd:YAG Q-switched laser producing intensive light emission with apparent 6 kW/sq cm pump threshold and spectrum narrowing near 617 nm peak in the case of DCM doped waveguide. PM-567 doped waveguide pumped with CW Ar(+) laser (514 nm wavelength) far below threshold (0.1 W/sq.cm pump power) demonstrated emission spectrum narrowing near 616 nm peak with 18% power conversion slope efficiency. In this case emission spectrum modification was caused by the enhanced light absorption along the direction of propagating waveguide modes. Changing length, thickness, and other morphlogical waveguide parameters one can modify emission spectrum in predictable direction. The results show that polymeric waveguides, especially based on high temperature polymers such as Pl, can be used to produce a varietiy of active and passive silicon compatible integrated optical components for aerospace applications.

Sarkisov, Sergey↗

NASA NTRS1995

Notes on the diversity of the properties of radio bursts observed on the nightside of Venus

We report on further studies of radio wave bursts detected by the Orbiting Electric Field Detector (OEFD) on the Pioneer Venus Orbiter (PVO) in the nightside ionosphere of Venus. We have tested a total of 25 cases of wave burst activity for evidence of whistler-mode propagation to the spacecraft from impulsive subionospheric sources. As in a previous study of 11 of these cases (Sonwalkar et al., 1991) we find at least two distinct classes of events, one, mostly involving bursts at 100 Hz only, that passes certain tests for whistler-mode propagation, and another, mostly involving bursts in two or more of the four PVO narrowband channels (at 100 Hz, 730 Hz, 5.4 kHz, and 30 kHz), that fails to pass the tests. The subionospheric lightning hypothesis continues to be tenable as a candidate explanation for many of the 100 Hz-only events, but its number of 100 Hz-only cases that do no pass all the applicable whistler-mode tests, as well as the existence at a wide range of altitudes of multichannel cases that are clearly not propagating whistler-mode waves. The wideband bursts are often observed at altitudes above 1000 km and frequently occur in regions of locally reduced electron density. Those observed at high altitude (and possibly low altitude as well) are believed to be generated near the spacecraft, possibly by an as yet unknown mechanism responsible for similar burst observations made near Earth and other planets.

Sonwalkar, Vikas S.↗

NASA NTRS1998

Conductance of Carbon Nanotubes

The recent report of quantized conductance in a 4 m long multiwalled nanotube (MWNT) raises the exciting possibility of ballistic transport at room temperature over relatively long distances. We argue that this is made possible by the special symmetry of the eigenstates of the lowest propagating modes in metallic nanotubes which suppresses backscattering. This unusual effect is absent for the higher propagating modes so that transport is not ballistic once the bias exceeds the cut-off energy for the higher modes, which is estimated to be approximately 75 meV for nanotubes of diameter approximately 15 nm. Also, we show that the symmetry of the eigenstates can significantly affect their coupling to the reservoir and hence the contact resistance. A simple model is presented that can be used to understand the observed conductance-voltage characteristics.

Datta, Supriyo↗

DOE OSTI2026

Counter-propagating toroidal Alfvén eigenmodes in tokamaks

Mechanisms of destabilization of toroidal Alfvén eigenmodes (TAEs) in tokamaks are analyzed with the aim to reveal those leading to modes propagating in the direction opposite to plasma current, i.e. counter-propagating modes (ctr-TAE). Plasmas with fast-ions sources [such as neutral beam injection (NBI), ion cyclotron resonance heating, fusion reactions] and without them (Ohmic discharges) are considered. A particular NSTX-U experiment with NBI, where co- and counter-propagating TAEs were observed simultaneously (Podestà et al 2018 Nucl. Fusion 58 082023), is considered. It is concluded that both types of TAEs occurred because their destabilization was caused by the velocity anisotropy of beam ions, which overrode effects of spatial inhomogeneity of these ions.

Alfvénic instabilities↗

NASA NTRS1984

Polarization effects in silicon-clad optical waveguides

By changing the thickness of a semiconductor cladding layer deposited on a planar dielectric waveguide, the TE or TM propagating modes may be selectively attenuated. This polarization effect is due to the periodic coupling between the lossless propagating modes of the dielectric slab waveguide and the lossy modes of the cladding layer. Experimental tests involving silicon claddings show high selectivity for either polarization.

Carson, R. F.↗

NASA NTRS1994

A test of the Hall-MHD model: Application to low-frequency upstream waves at Venus

Early studies suggested that in the range of parameter space where the wave angular frequency is less than the proton gyrofrequency and the plasma beta, the ratio of the thermal to magnetic pressure, is less than 1 magnetohydrodynamics provides an adequate description of the propagating modes in a plasma. However, recently, Lacombe et al. (1992) have reported significant differences between basic wave characteristics of the specific propagation modes derived from linear Vlasov and Hall-magnetohydrodynamic (MHD) theories even when the waves are only weakly damped. In this paper we compare the magnetic polarization and normalization magnetic compression ratio of ultra low frequency (ULF) upstream waves at Venus with magnetic polarization and normalized magnetic compression ratio derived from both theories. We find that while the 'kinetic' approach gives magnetic polarization and normalized magnetic compression ratio consistent with the data in the analyzed range of beta (0.5 less than beta less than 5) for the fast magnetosonic mode, the same wave characteristics derived from the Hall-MHD model strongly depend on beta and are consistent with the data only at low beta for the fast mode and at high beta for the intermediate mode.

Orlowski, D. S.↗

NASA NTRS1980

Comparison of several inflow control devices for flight simulation of fan tone noise using a JT15D-1 engine

The paper describes the tests of four devices intended to reduce inflow disturbances and turbulences using a JT15D-1 turbofan engine. The tests were made to simulate the in-flight fan tone noise; the inflow control devices (ICD's) consisted of honeycomb/screen structures mounted over the engine inlet. The ICD's ranged from 1.6 to 4 fan diameters in size, and were made with several fabrication methods. All the ICD's significantly reduced the BPF tone in the far-field directivity patterns, but the smallest ICD's introduced propagating modes which could be recognized by additional lobes in the patterns. The JT15D-1 engine had a tone source which generated a strong propagating mode at fan speeds corresponding to 'approach' power and higher. Data from a typical transducer showed that the unsteady inflow distortion modes were eliminated or reduced when either of the ICD's was installed.

Mcardie, J. G.↗

NASA NTRS1986

Analysis of mixed-mode crack propagation using the boundary integral method

Crack propagation in a rotating inner raceway of a high speed roller bearing is analyzed using the boundary integral equation method. The method consists of an edge crack in a plate under tension, upon which varying Hertzian stress fields are superimposed. A computer program for the boundary integral equation method was written using quadratic elements to determine the stress and displacement fields for discrete roller positions. Mode I and Mode II stress intensity factors and crack extension forces G sub 00 (energy release rate due to tensile opening mode) and G sub r0 (energy release rate due to shear displacement mode) were computed. These calculations permit determination of that crack growth angle for which the change in the crack extension forces is maximum. The crack driving force was found to be the alternating mixed-mode loading that occurs with each passage of the most heavily loaded roller. The crack is predicted to propagate in a step-like fashion alternating between radial and inclined segments, and this pattern was observed experimentally. The maximum changes DeltaG sub 00 and DeltaG sub r0 of the crack extension forces are found to be good measures of the crack propagation rate and direction.

Mendelson, A.↗

NASA NTRS1985

Asymptotic high frequency analysis of the electromagnetic backscattering from an inlet model consisting of piecewise linearly tapered sections

Electromagnetic backscattering from an open ended three dimensional inlet model is analyzed and computed patterns are compared with results of experimental measurements. The model is comprised of two sections. The first section consists of a linearly tapered waveguide with a rectangular opening at one end and the other end is connected to the second section which is a uniform rectangular waveguide with a planar perfectly conducting termination. The model is electrically large so that many propagating modes are excited. The method of analysis contains conventional aperture integration and modal techniques combined with high frequency techniques, which employ concepts such as modal rays, geometrical theory of diffraction and equivalent currents. For the cases considered, it is shown that only a few of the many propagating modes contribute appreciably to the backscattered field. These modes are selected according to their modal ray angle directions.

Altintas, A.↗

NASA NTRS1996

Aeroacoustic Analysis of Turbofan Noise Generation

This report provides an updated version of analytical documentation for the V072 Rotor Wake/Stator Interaction Code. It presents the theoretical derivation of the equations used in the code and, where necessary, it documents the enhancements and changes made to the original code since its first release. V072 is a package of FORTRAN computer programs which calculate the in-duct acoustic modes excited by a fan/stator stage operating in a subsonic mean flow. Sound is generated by the stator vanes interacting with the mean wakes of the rotor blades. In this updated version, only the tonal noise produced at the blade passing frequency and its harmonics, is described. The broadband noise component analysis, which was part of the original report, is not included here. The code provides outputs of modal pressure and power amplitudes generated by the rotor-wake/stator interaction. The rotor/stator stage is modeled as an ensemble of blades and vanes of zero camber and thickness enclosed within an infinite hard-walled annular duct. The amplitude of each propagating mode is computed and summed to obtain the harmonics of sound power flux within the duct for both upstream and downstream propagating modes.

Meyer, Harold D.↗