SEARCH · Search NASA

Results for “Placement Study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS2007

Fluorescence Visualization of Hypersonic Flow over Rapid Prototype Wind-Tunnel Models

Reentry models for use in hypersonic wind tunnel tests were fabricated using a stereolithography apparatus. These models were produced in one day or less, which is a significant time savings compared to the manufacture of ceramic or metal models. The models were tested in the NASA Langley Research Center 31-Inch Mach 10 Air Tunnel. Most of the models did not survive repeated tests in the tunnel, and several failure modes of the models were identified. Planar laser-induced fluorescence (PLIF) of nitric oxide (NO) was used to visualize the flowfields in the wakes of these models. Pure NO was either seeded through tubes plumbed into the model or via a tube attached to the strut holding the model, which provided localized addition of NO into the model s wake through a porous metal cylinder attached to the end of the tube. Models included several 2-inch diameter Inflatable Reentry Vehicle Experiment (IRVE) models and 5-inch diameter Crew Exploration Vehicle (CEV) models. Various configurations were studied including different sting placements relative to the models, different model orientations and attachment angles, and different NO seeding methods. The angle of attack of the models was also varied and the location of the laser sheet was scanned to provide three-dimensional flowfield information. Virtual Diagnostics Interface technology, developed at NASA Langley, was used to visualize the data sets in post processing. The use of calibration "dotcards" was investigated to correct for camera perspective and lens distortions in the PLIF images. Lessons learned and recommendations for future experiments are discussed.

Alderfer, D. W.↗

NASA NTRS1983

Component number and placement in large space structure control

Studies are carried out to assist the designer of the control system for a large flexible space structure in his choice of how many actuators and sensors to incorporate in the system, and where to locate them on the structure. The degree of controllability and minimum control energy strategy for driving the system are described.

Vandervelde, W. E.↗

NASA NTRS2014

Shielding of Turbomachinery Broadband Noise from a Hybrid Wing Body Aircraft Configuration

The results of an experimental study on the effects of engine placement and vertical tail configuration on shielding of exhaust broadband noise radiation are presented. This study is part of the high fidelity aeroacoustic test of a 5.8% scale Hybrid Wing Body (HWB) aircraft configuration performed in the 14- by 22-Foot Subsonic Tunnel at NASA Langley Research Center. Broadband Engine Noise Simulators (BENS) were used to determine insertion loss due to shielding by the HWB airframe of the broadband component of turbomachinery noise for different airframe configurations and flight conditions. Acoustics data were obtained from flyover and sideline microphones traversed to predefined streamwise stations. Noise measurements performed for different engine locations clearly show the noise benefit associated with positioning the engine nacelles further upstream on the HWB centerbody. Positioning the engine exhaust 2.5 nozzle diameters upstream (compared to 0.5 nozzle diameters downstream) of the HWB trailing edge was found of particular benefit in this study. Analysis of the shielding performance obtained with and without tunnel flow show that the effectiveness of the fuselage shielding of the exhaust noise, although still significant, is greatly reduced by the presence of the free stream flow compared to static conditions. This loss of shielding is due to the turbulence in the model near-wake/boundary layer flow. A comparison of shielding obtained with alternate vertical tail configurations shows limited differences in level; nevertheless, overall trends regarding the effect of cant angle and vertical location are revealed. Finally, it is shown that the vertical tails provide a clear shielding benefit towards the sideline while causing a slight increase in noise below the aircraft.

Hutcheson, Florence V.↗

NASA NTRS2013

Computational Assessment of the Benefits of Boundary Layer Ingestion for the D8 Aircraft

To substantially reduce the fuel burn of future commercial transportation aircraft, the boundary layer ingestion idea is investigated. The idea is that an engine placed in the wake of the aircraft it is propelling is more efficient than a conventional engine placement under the wing or on pods mounted to the rear of the fuselage. The top, rear of the fuselage is thus designed to act as a diffuser such that the engines can be placed there with a minimal nacelle. The boundary layer thickens over the rear of the fuselage such that a large portion of it is ingested by the fan. To assess whether the boundary layer ingesting (BLI) engine placement is indeed advantageous, a study of the nacelle aerodynamics is carried out using Overflow, a viscous CFD flow solver that uses overset meshes. The computed forces and moments are compared to a wind tunnel experiment for validation. Some aspects of the design are verified using the simulation results. Finally, the effect of the nacelle placement is assessed by comparing the BLI nacelle configuration to a podded nacelle configuration and to the unpowered (without nacelles) aircraft.

aircraft↗

NASA NTRS1993

Sensitivity of dual-wall structures under hypervelocity impact to multi-layer thermal insulation thickness and placement

Results are presented from an experimental study in which Al dual-wall structures were tested, under various high-speed impact conditions, with a view to the effect of multilayer insulation thickness and location on perforation resistance. Attention is given to comparisons of the damage sustained by dual-wall systems with multilayer insulation blankets of various thicknesses and at various locations within the dual-wall system, under comparable impact loading conditions. The placement of the insulation has a significant effect on the ballistic limit of the dual-wall structures considered, while reducing insulation thickness by as much as a third did not.

Schonberg, William P.↗

NASA NTRS1980

Recent results on output feedback problems

Given a real linear system sigma = (A, B, C) with m inputs, p outputs and degree n, the problem of generic pole placement by output feedback is studied, which is to compute the constant C(m,p) such that the inequality C(m,p) not less than n is necessary and sufficient for generically positioning the poles of the generic linear system by constant output feedback. A constant C prime (m,p) is determined, which gives a sufficient condition for generic pole placement and which, to the best of the author's knowledge, is at least as good an estimate of C(m,p) as any in the literature. Some results on the construction of solutions in case mp = n are announced, based on the degree formula of Brockett and Byrnes and the Galois theory. In particular, a question raised by Anderson, Bose, and Jury, on the existence of a rational procedure for computing the feedback law from the desired characteristic polynomial is answered.

Byrnes, C. I.↗

NASA NTRS1976

A statistical method for treating molecular line opacities

A method for treating atomic and molecular line opacities in cool stellar atmospheres by a statistical opacity sampling is investigated. Under the usual assumptions of plane-parallel geometry, radiative equilibrium, hydrostatic equilibrium, and LTE, each radiative quantity is computed monochromatically at each chosen frequency and depth without any averaging of the opacity. The number of frequencies needed to allow an accurate integration of the energy flux over a given spectral interval is investigated as a function of depth, including opacity for both CN and C2. This method is extended to the calculation of a model atmosphere of a star, and the effect of the number and placement of frequency points is studied. The method is applied to treating molecular lines of CO, C2, and CN in a cool carbon star. Significant advantages of the opacity sampling method are its flexibility, which permits computation of models having arbitrary variations of chemical composition and of opacity with wavelength and depth, and generalizability to include departures from LTE.

Sneden, C.↗

NASA NTRS1988

Development of a two-dimensional skin friction balance nulling circuit using multivariable control theory

Measurement of planar skin friction forces in aerodynamic testing currently requires installation of two perpendicularly mounted, single-axis balances; consequently, force components must be sensed at two distinct locations. A two-axis instrument developed at the Langley Research Center to overcome this disadvantage allows measurement of a two-dimensional force at one location. This paper describes a feedback-controlled nulling circuit developed for the NASA two-axis balance which, without external compensation, is inherently unstable because of its low friction mechanical design. Linear multivariable control theory is applied to an experimentally validated mathematical model of the balance to synthesize a state-variable feedback control law. Pole placement techniques and computer simulation studies are employed to select eigenvalues which provide ideal transient response with decoupled sensing dynamics.

Tripp, John S.↗

NASA NTRS2022

Optimizing Landsat Next Shortwave Infrared Bands for Crop Residue Characterization

This study focused on optimizing the placement of shortwave infrared (SWIR) bands for pixel-level estimation of fractional crop residue cover (f R ) for the upcoming Landsat Next mission. We applied an iterative wavelength shift approach to a database of crop residue field spectra collected in Beltsville, Maryland, USA (n = 916) and computed generalized two- and three-band spectral indices for all wavelength combinations between 2000 and 2350 nm, then used these indices to model field-measured f R . A subset of the full dataset with a Normalized Difference Vegetation Index (NDVI) < 0.3 threshold (n = 643) was generated to evaluate green vegetation impacts on f R estimation. For the two-band wavelength shift analyses applied to the NDVI < 0.3 dataset, a generalized normalized difference using 2226 nm and 2263 nm bands produced the top f R estimation performance (R 2 = 0.8222; RMSE = 0.1296). These findings were similar to the established two-band Shortwave Infrared Normalized Difference Residue Index (SINDRI) (R 2 = 0.8145; RMSE = 0.1324). Performance of the two-band generalized normalized difference and SINDRI decreased for the full-NDVI dataset (R 2 = 0.5865 and 0.4144, respectively). For the three-band wavelength shift analyses applied to the NDVI < 0.3 dataset, a generalized ratio-based index with a 2031–2085–2216 nm band combination, closely matching established Cellulose Absorption Index (CAI) bands, was top performing (R 2 = 0.8397; RMSE = 0.1231). Three-band indices with CAI-type wavelengths maintained top f R estimation performance for the full-NDVI dataset with a 2036–2111–2217 nm band combination (R 2 = 0.7581; RMSE = 0.1548). The 2036–2111–2217 nm band combination was also top performing in f R estimation (R 2 = 0.8690; RMSE = 0.0970) for an additional analysis assessing combined green vegetation cover and surface moisture effects. Our results indicate that a three-band configuration with band centers and wavelength tolerances of 2036 nm (±5 nm), 2097 nm (±14 nm), and 2214 (±11 nm) would optimize Landsat Next SWIR bands for f R estimation.

Landsat Next↗

NASA NTRS1996

Determination of Shed Ice Particle Size Using High Speed Digital Imaging

A full scale model of an aircraft engine inlet was tested at NASA Lewis Research Center's Icing Research Tunnel. Simulated natural ice sheds from the engine inlet lip were studied using high speed digital image acquisition and image analysis. Strategic camera placement integrated at the model design phase allowed the study of ice accretion on the inlet lip and the resulting shed ice particles at the aerodynamic interface plane at the rear of the inlet prior to engine ingestion. The resulting digital images were analyzed using commercial and proprietary software to determine the size of the ice particles that could potentially be ingested by the engine during a natural shedding event. A methodology was developed to calibrate the imaging system and insure consistent and accurate measurements of the ice particles for a wide range of icing conditions.

Broughton, Howard↗

NASA NTRS1978

Galileo satellite tour maneuver strategies

In January of 1982 the United States will launch Galileo, the first space mission designed to perform an intensive tour of the Galilean satellites of Jupiter. This paper discusses the results of preliminary maneuver strategy studies for typical interplanetary and orbital phases of the Galileo mission. These studies include the effects of maneuver placement and various linear control algorithms on propellant consumption as determined by Monte Carlo analysis. Estimates of total propellant required for various probabilities of mission success are also given.

Miller, L. J.↗

NASA NTRS1986

Construction and control of large space structures

Recent NASA research efforts on space construction are reviewed. Preliminary results of the EASE/ACCESS Shuttle experiments are discussed. A 45-foot beam was constructed on orbit in 30 minutes using a manual assembly technique at a work station. A large tetrahedron was constructed several times using a free floating technique. The capability of repair, utilities installation, and handling the structures using a mobile foot restraint on the RMS was also demonstrated. Implications of the experiments for Space Station are presented. Models of 5-meter Space Station structure together with neutral buoyancy simulations suggest manual assembly techniques are feasible. Selected research on control of flexible structures is discussed. To support planned flight experiments, studies of the design and optimal placement of distributed active dampers are underway.

Card, M. F.↗

NASA NTRS1992

Development of thermoplastic composite aircraft structures

Efforts focused on the use of thermoplastic composite materials in the development of structural details associated with an advanced fighter fuselage section with applicability to transport design. In support of these designs, mechanics developments were conducted in two areas. First, a dissipative strain energy approach to material characterization and failure prediction, developed at the Naval Research Laboratory, was evaluated as a design/analysis tool. Second, a finite element formulation for thick composites was developed and incorporated into a lug analysis method which incorporates pin bending effects. Manufacturing concepts were developed for an upper fuel cell cover. A detailed trade study produced two promising concepts: fiber placement and single-step diaphragm forming. Based on the innovative design/manufacturing concepts for the fuselage section primary structure, elements were designed, fabricated, and structurally tested. These elements focused on key issues such as thick composite lugs and low cost forming of fastenerless, stiffener/moldine concepts. Manufacturing techniques included autoclave consolidation, single diaphragm consolidation (SDCC) and roll-forming.

Renieri, Michael P.↗

NASA NTRS1996

Improved Models for the Porous Surface with Passive Control

A computational investigation of afterbody flow using a passive control method is conducted. The passive control method consists of a porous surface placed over a plenum. The purpose of the passive control method is to exploit the adverse pressure gradient present in afterbody flow in an attempt to reduce boundary layer separation and afterbody drag. Four different porous wall models are used to model the transpiration velocity in the region of passive control. A three-dimensional, time-dependent, Reynolds-averaged, simplified Navier-Stokes solver, PAB3D, is used to simulate afterbody flow with and without passive control. Three afterbody configurations with boat-tail angles of 10, 20, and 30 deg. are used to obtain two-dimensional solutions with a freestream Mach number of 0.6 and nozzle pressure ratio of 6. The region of passive control was initially placed from 20-60% of the nozzle length. The effect of the porous placement and porous extent is also studied. Baseline (no porosity) two-dimensional solutions are qualitatively similar to experimental data but under-predict the magnitude of the pressure recovery. Results for the subsonic solutions show losses in the pressure recovery for some cases with passive control. Three-dimensional effects are also investigated and seen to be very significant. Three-dimensional baseline solutions, for both sub- and super-critical freestream Mach numbers, compare very favorably with the experimental data in comparison to the two-dimensional solution. Future work is required to examine three-dimensional afterbody flows with passive porosity.

Kraushaar, Sandra L.↗

NASA NTRS2004

MER Field Geologic Traverse in Gusev Crater, Mars: Initial Results From the Perspective of Spirit

This report casts the initial results of the traverse and science investigations by the Mars Exploration Rover (MER) Spirit at Gusev crater [1] in terms of data sets commonly used in field geologic investigations: Local mapping of geologic features, analyses of selected samples, and their location within the local map, and the regional context of the field traverse in terms of the larger geologic and physiographic region. These elements of the field method are represented in the MER characterization of the Gusev traverse by perspective-based geologic/morphologic maps, the placement of the results from Mossbauer, APXS, Microscopic Imager, Mini-TES and Pancam multispectral studies in context within this geologic/ morphologic map, and the placement of the overall traverse in the context of narrow-angle MOC (Mars Orbiter Camera) and descent images. A major campaign over a significance fraction of the mission will be the first robotic traverse of the ejecta from a Martian impact crater along an approximate radial from the crater center. The Mars Exploration Rovers have been conceptually described as 'robotic field geologists', that is, a suite of instruments with mobility that enables far-field traverses to multiple sites located within a regional map/image base at which in situ analyses may be done. Initial results from MER, where the field geologic method has been used throughout the initial course of the investigation, confirm that this field geologic model is applicable for remote planetary surface exploration. The field geologic method makes use of near-field geologic characteristics ('outcrops') to develop an understanding of the larger geologic context through continuous loop of rational steps focused on real-time hypothesis identification and testing. This poster equates 'outcrops' with the locations of in situ investigations and 'regional context' with the geology over distance of several kilometers. Using this fundamental field geologic method, we have identified the basic local geologic materials on the floor of Gusev at this site, their compositions and likely lithologies, origins, processes that have modified these materials, and their potential significance in the interpretation of the regional geology both spatially and temporally.

Crumpler, L.↗

NASA NTRS2002

Stimulus and recording variables and their effects on mammalian vestibular evoked potentials

Linear vestibular evoked potentials (VsEPs) measure the collective neural activity of the gravity receptor organs in the inner ear that respond to linear acceleration transients. The present study examined the effects of electrode placement, analog filtering, stimulus polarity and stimulus rate on linear VsEP thresholds, latencies and amplitudes recorded from mice. Two electrode-recording montages were evaluated, rostral (forebrain) to 'mastoid' and caudal (cerebellum) to 'mastoid'. VsEP thresholds and peak latencies were identical between the two recording sites; however, peak amplitudes were larger for the caudal recording montage. VsEPs were also affected by filtering. Results suggest optimum high pass filter cutoff at 100-300 Hz, and low pass filter cutoff at 10,000 Hz. To evaluate stimulus rate, linear jerk pulses were presented at 9.2, 16, 25, 40 and 80 Hz. At 80 Hz, mean latencies were longer (0.350-0.450 ms) and mean amplitudes reduced (0.8-1.8 microV) for all response peaks. In 50% of animals, late peaks (P3, N3) disappeared at 80 Hz. The results offer options for VsEP recording protocols. Copyright 2002 Elsevier Science B.V.

Non-NASA Center↗

NASA NTRSDate not supplied

Unsteady Pressure Measurement on a Simplified High-Lift Configuration of the Common Research Model using Active Flow Control

The High-Lift Common Research Model (CRM-HL) is a product of the NASA Advanced Air Transport Technology (AATT) Project intended to study various high-lift aerodynamic phenomena including enhanced lift, acoustic noise generation, and optimum placement of leading and trailing-edge devices. The current study was conducted in the NASA Langley 14-by 22-Foot Subsonic Tunnel (14x22) for the purpose of evaluating enhanced lift through the use of active flow control (AFC). The current paper documents the effect of sweeping-jet actuation combined with steady blowing on a simplified high-lift configuration using unsteady pressure measurements. The time-series parameters for the measurements are documented as well as the data acquisition system used to acquire the data. An uncertainty analysis will be presented in order to document the system performance and provide an estimate of the data quality. Repeatability of the data will be shown along with trends associated with model angle of attack, and those associated with changes in the nozzle pressure ratio (NPR) of the AFC system.

Common Research Model↗

NASA NTRSDate not supplied

Unsteady Pressure Measurements on a Simplified High-Lift Configuration of the Common Research Model using Active Flow Control

The High-Lift Common Research Model (CRM-HL) is a product of the NASA Advanced Air Transport Technology (AATT) Project intended to study various high-lift aerodynamic phenomena including enhanced lift, acoustic noise generation, and optimum placement of leading and trailing-edge devices. The current study was conducted in the NASA Langley 14-by 22-Foot Subsonic Tunnel (14x22) for the purpose of evaluating enhanced lift through the use of active flow control (AFC). The current paper documents the effect of sweeping-jet actuation combined with steady blowing on a simplified high-lift configuration using unsteady pressure measurements. The time-series parameters for the measurements are documented as well as the data acquisition system used to acquire the data. An uncertainty analysis will be presented in order to document the system performance and provide an estimate of the data quality. Repeatability of the data will be shown along with trends associated with model angle of attack, and also those associated with changes in the nozzle pressure ratio (NPR) of the AFC system.

Active Flow Control↗