SEARCH · Search NASA

Results for “Power offset”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Precision Time Protocol Synchronization Under Network Impairments

This bulletin examines how network anomalies disrupt Precision Time Protocol synchronization on long terrestrial links used for grid timing. Using a CAST testbed with emulated impairments, we measured delay, offset, and time interval error while monitoring packet rates. Symmetric delays did not perturb synchronization, whereas asymmetric delays produced false offsets; jitters were largely filtered out, but they delayed synchronization recovery; moderate packet loss was tolerated, while severe loss forced holdover and loss of synchronization.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2026

A Unified Beam-Dynamics and Hardware Design Framework for Hybrid Nonlinear-Kicker Injection in NSLS-II

Nonlinear kickers (NLKs) enable off-axis injection in ultralow-emittance storage rings by providing a strong kick to the injected beam while remaining nearly transparent to the stored beam. In hybrid schemes, a conventional four-kicker bump defines the injected trajectory, and the NLK reduces the first-turn action under constrained beam offset and optics conditions. Effective operation additionally requires stable and reproducible first-turn injection trajectories. We develop a compact action–angle framework that expresses NLK dynamics in terms of Courant–Snyder invariants and yields an analytical bound on achievable action reduction. This formulation provides direct design rules for NLK placement, phase advance, injected-beam offset, and kicker field profile. Within this framework, we identify the 8-wire NLK as a practical baseline and extend its design by relaxing the square-geometry constraint, enabling inward shifting of the off-axis field peak while preserving on-axis field and gradient cancellation. Application to the NSLS-II lattice shows how aperture, pulsed-power, and mechanical constraints combine to determine a coupled design solution. Multi-turn tracking confirms that candidate NLK locations maintain sufficient stay-clear (aperture-clearance) margin, while the optimized wire geometry reduces the required current and Lorentz force load. The results establish a unified approach for NLK-assisted injection design and provide a practical pathway for upgrades in diffraction-limited storage rings.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Current-Activated Reactive Ultrafast Joining (CARUJ)

We have demonstrated Current Activated Reactive Ultrafast Joining (CARUJ) as a novel approach for rapid fabrication of similar and dissimilar materials, such as ceramic-ceramic and ceramic-metal joint assemblies. The CARUJ technology utilizes resistive heating of carbon-based materials to apply localized heat at, (through or around) joint zones at rates of 10 1 -10 2 ˚C/min, enabling joining at time scales considerably shorter (several minutes as opposed to hours) than conventional approaches for similar systems. Herein, we present our findings while evaluating the CARUJ concept. Three methods of heat application were evaluated: (i) using carbon joule heating elements to apply heat directly through the joint interface; (ii) using flexible joule heating elements to locally apply heat around the assembly interface; and (iii) non-contact heating of the joint assembly using inductive power. Schemes (ii) and (iii) proved to be the most effective in producing mechanically sound reliable joints. We demonstrated single-step fabrication of dense SiC-SiC joints with a Si- SiC interface using minimal pressure (1–2 MPa) in under 30 minutes. Measured average joint strengths of about 15 MPa are initially achieved for joined bodies when tested in single lap offset (SLO) compressive shear, while tuning of the interfacial composition along with a reduction in interlayer thickness, results in improved joint strengths of approximately 43 MPa. We further demonstrated SiC-SiC joining using Active Brazing Alloys (ABAs) proof of concept joining of tubular geometries. The versatility of CARUJ is demonstrated by utilizing non-contact heating via induction, to join dissimilar materials systems of SiC, SS316 and MAX phase ceramics with ABA interlayers. The localized and rapid heat application realizes a versatile material joining technique that can be extended for joining components at the plant site.

36 MATERIALS SCIENCE↗

NASA NTRS1993

Radio Metric Errors Due to Mismatch and Offset Between a DSN Antenna Beam and the Beam of a Troposphere Calibration Instrument

Two components of the error of a troposphere calibration measurement were quantified by theoretical calculations. The first component is a beam mismatch error, which occurs when the calibration instrument senses a conical volume different from the cylindrical volume sampled by a Deep Space Network (DSN) antenna. The second component is a beam offset error, which occurs if the calibration instrument is not mounted on the axis of the DSN antenna. These two error sources were calculated for both delay (e.g., VLBI) and delay rate (e.g., Doppler) measurements. The beam mismatch error for both delay and delay rate drops rapidly as the beamwidth of the troposphere calibration instrument (e.g., a water vapor radiometer or an infrared Fourier transform spectrometer) is reduced. At a 10-deg elevation angle, the instantaneous beam mismatch error is 1.0 mm for a 6-deg beamwidth and 0.09 mm for a 0.5-deg beam (these are the full angular widths of a circular beam with uniform gain out to a sharp cutoff). Time averaging for 60-100 sec will reduce these errors by factors of 1.2-2.2. At a 20-deg elevation angle, the lower limit for current Doppler observations, the beam-mismatch delay rate error is an Allan standard deviation over 100 sec of 1.1 x 10 -14 with a 4-deg beam and 1.3 x 10 -15 for a 0.5-deg beam. A 50-m beam offset would result in a fairly modest (compared to other expected error sources) delay error (less than or equal to 0.3 mm for 60-sec integrations at any elevation angle is greater than or equal to 6 deg). However, the same offset would cause a large error in delay rate measurements (e.g., an Allan standard deviation of 1.2 x 10 -14 over 100 sec at a 20-deg elevation angle), which would dominate over other known error sources if the beamwidth is 2 deg or smaller. An on-axis location is essential for accurate troposphere calibration of delay rate measurements. A half-power beamwidth (for a beam with a tapered gain profile) of 1.2 deg or smaller is desired for calibration of all types of radio metrics. A water-vapor radiometer calibration beam of this size with very low sidelobes would require a clear aperture antenna with a diameter of at least 1.5 m if the primary water vapor sensing channel were in the 20-22 GHz range.

R P Linfield↗

DOE OSTI2025

Self-generated electrokinetic flows from active-charged boundary patterns

We develop a hydrodynamic description of self-generated electrolyte flow in capillaries whose bounding walls feature nonuniform distributions of charge nonuniform active ionic fluxes. The hydrodynamic velocity arising in such a system has components that are forbidden by symmetry in the absence of charge and fluxes. However, when these two boundary mechanisms are simultaneously present, they can lead to a symmetry broken state where steady flows with both unidirectional and circulatory components emerge. We show that these flow states arise when modulated boundary patterns of charge and fluxes are offset by a flux-charge phase difference, which is associated with the separation between sites of their peak densities on the wall. Mismatch in diffusivity of cationic and anionic species can modify the flow states and becomes an enhancing factor when fluxes of both ion species are being produced together at the same site. We demonstrate that this mechanism can be realized with a microfluidic generator that is powered by enzyme-coated patches that catalyze reactants in the solution to produce fluxes of ions. The local ionic elevation or depletion, which disrupts a nonuniform double layer, promotes self-induced gradients yielding persistent body forces to generate bulk fluid motion. Our work quantifies a boundary-driven mechanism behind self-sustained electrolyte flow in confined environments that exists without any external bulk-imposed fields or gradients. It provides a theoretical framework for understanding the combined effect of active and charged boundaries that are relevant in biological or soft matter systems, and can be utilized in electrofluidic and iontronic applications.

active matter↗

DOE OSTI2026

PWR Core Analysis for Cycle Extension and Uprates with LEU+ Accident Tolerant Fuel and 80 GWd/Tonne Burnup Limit

The U.S. Nuclear Regulatory Commission has recently drafted a rule enabling fuel burnup increase in light water reactors up to 80 GWd/t. In conjunction with use of fuel enrichment up to 10%, and accident tolerant fuel (ATF), this is anticipated to facilitate 24-month cycles in PWRs, along with further power uprates. In this paper, PWR core analysis is performed for 20% increased PWR power output along with cycle extension up to 24 months, in combination with use of chromia-doped fuel and chromium-coated clad, considered to be the most near-term ATF concepts. In combination, these lead to challenging conditions with a core average discharge burnup of up to ~74 GWd/t, challenging even the 80 GWd/t burnup limit. Analysis is performed using the 2-step method with POLARIS (within SCALE) used for the lattice calculations and PARCS for the core calculations. Core designs are first baselined for current operating conditions (LEU, 62 GWd/t discharge burnup limit) and then derived that meet cycle constraints on power distribution and the updated lead pin discharge burnup limit while maintaining at least two batches of fuel in the core. Gadolina loadings in fuel pins of up to 8% are used, with enrichment zoning both within the core and, to a limited extent, within assemblies. Here, doped fuel with coated cladding can utilize the same core designs as the reference UOX cores, exhibiting slightly lower burnup due to higher fuel density, which also offsets the slight reactivity penalty from the doping and coating. For the analysis performed here, doped fuel enabled a core with 24-month cycle and 20% uprate to stay within the 80 GWd/t lead pin discharge burnup limit.

LEU+↗

DOE OSTI2026

Leaf Wax Hydrogen Isotopes Reflect Storm Track Position Over Western North America

Proxy records of past climates have yielded powerful insights into regional hydroclimate dynamics. Novel insights may be gained by reconstructing spatiotemporal changes in precipitation isotopologues in past climate states that cannot be gleaned from individual site‐level studies. In this paper, we ask whether latitudinal gradients in the stable hydrogen isotopic composition of precipitation, as inferred from sedimentary leaf wax biomarkers, reflect aspects of large‐scale climate conditions in western North America (WNA). Modern coretop samples from offshore WNA show that leaf wax hydrogen isotopes broadly track the hydrogen isotopic composition of rainfall between 20 and 40N, but with an offset corresponding to a relatively constant “apparent fractionation” value. Poleward of 40N, the leaf wax signal may be complicated by fluvial transport of leaf waxes from the continental interior. Leaf wax‐inferred precipitation hydrogen isotopes show a shift to more negative values between 30 and 40N. We use modern observational data to show that this latitudinal range marks a major transition between the subtropical arid zone and the location of the midlatitude storm tracks over the northeast Pacific. Nudged water isotope‐enabled models capture the location of the arid to mesic climate transition with fidelity. This modern data set suggests that reconstructions of the latitudinal gradient of precipitation hydrogen isotopes can constrain the sensitivity of the storm tracks to shifts in climatic boundary conditions in past climate states. This approach can yield novel insights into past, present, and future hydroclimate variability in this arid region.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Life cycle assessment of a novel gas switching reforming for sustainable hydrogen production with CO2 capture

Gas switching reforming for hydrogen production (GSR-H2) presents an efficient, low-carbon hydrogen production method that incorporates integrated carbon capture, offering efficiency gains over traditional methods such as proton exchange membrane (PEM) electrolysis, steam methane reforming (SMR) and the newer method of chemical looping reforming (CLR). GSR-H2 has been demonstrated in lab scale which operates as an exothermic process that eliminates the need for additional natural gas combustion, using its own waste heat to generate process steam and partially offset energy usage through electricity production. Beyond its thermal self-sufficiency, GSR-H2 advances upon CLR by integrating all reaction stages within a single reactor cluster, eliminating the complexities of solid circulation, reducing capital costs, and enhancing overall process efficiency. This streamlined design simplifies scale-up and enables inherent CO2 separation with minimal energy penalty, making GSR-H2 a highly competitive pathway for low-carbon hydrogen production. This study presents the first life cycle assessment (LCA) of GSR-H2, offering a novel evaluation of this new process’s environmental impacts across diverse energy scenarios. Key findings reveal that in the renewables-powered scenario, GSR-H2 achieves a GWP of 2.77 kg CO2 eq per kg H2, a substantial improvement over SMR’s 10.4 kg CO2 eq and close to the low emissions of CLR (1.84 kg CO2 eq) and PEM electrolysis (1.85 kg CO2 eq). These results demonstrate GSR-H2’s competitive advantage as a lower-emission alternative, combining design simplicity and efficiency gains, especially in renewable-integrated systems. These results establish GSR-H2 as a competitive, scalable option for hydrogen production, particularly in decarbonization efforts.

03 NATURAL GAS↗

DOE OSTI2025

Feedstock-efficient conversion through hydrogen and formate-driven metabolism in Escherichia coli

Product yields for biomanufacturing processes are often constrained by the tight coupling of cellular energy generation and carbon metabolism in sugar-based fermentation systems. To overcome this limitation, we engineered Escherichia coli to utilize hydrogen gas (H 2 ) and formate (HCOO - ) as alternative sources of energy and reducing equivalents, thereby decoupling energy generation from carbon metabolism. This approach enabled precise suppression of decarboxylative oxidation during acetate growth, with 86.6 ± 1.6 % of electrons from hydrogen gas (via soluble hydrogenase from Cupriavidus necator H16) and 98.4 ± 3.6 % of electrons from formate (via formate dehydrogenase from Pseudomonas sp. 101) offsetting acetate oxidation. Hydrogen gas supplementation led to a titratable and stoichiometric reduction in CO 2 evolution in acetate-fed cultures. Metabolomic analysis suggests that this metabolic decoupling redirects carbon flux through the glyoxylate shunt, partially bypassing two decarboxylative steps in the TCA cycle. Here, we demonstrated the utility of this strategy by applying it to mevalonate biosynthesis, where formate supplementation during glucose fermentation increased titers by 57.6 % in our best-performing strain. Flux balance analysis further estimated that 99.0 ± 2.8 % of electrons from formate were used to enhance mevalonate production. These findings highlight a broadly applicable strategy for enhancing biomanufacturing efficiency by leveraging external reducing power to optimize feedstock and energy use.

Biomanufacturing↗

DOE OSTI2025

Techno-economic evaluation of emission control configurations for AMP/PZ-based post-combustion CO 2 capture

Minimizing the environmental impacts of amine-based post-combustion carbon capture technologies is essential for regulatory compliance and public acceptance. Experimental campaigns at RWE's CO 2 capture pilot plant in Niederaussem using CESAR1 demonstrated that combining existing emission abatement technologies can substantially reduce the concentration of amines and degradation products in the CO 2 -depleted flue gas to below the detection limit of an infrared spectrometer. The campaign confirmed that a proprietary dry bed technology (OEASE aerozone™) or a second water wash can reduce AMP and PZ emissions to below 1 mg/Nm 3 . However, an acid or chemically active wash downstream of the water wash is necessary to reduce NH 3 emissions to very low levels (<2 mg/Nm 3 ). Combining a dry bed with an acid wash significantly reduces both the required acid solution and the resulting acid waste. The techno-economic analysis indicates that implementing emission mitigation technologies provides substantial environmental benefits for the CESAR1 process, with only a marginal increase (<1 €/tCO 2 ) in both the carbon capture cost (CCC) and CO 2 avoidance cost (CAC). The additional capital cost associated with extra column packing is offset by operational cost savings from reduced solvent losses. For stringent emission permits targeting NH 3 , a configuration combining a dry bed upstream of the water wash followed by an acid wash achieves the best balance between emission control and cost efficiency. This configuration results in a Levelized Cost of Electricity (LCOE) of 143 €/MWh, a CCC of 45.4 €/tCO 2 , and a CAC of 88.4 €/tCO 2 .

AMP↗

DOE OSTI2026

Benchmark of the Chlorine Worth Study Experiments in Support of Chlorine Nuclear Data Validation for Nuclear Criticality Safety

The Chlorine Worth Study (CWS) was a critical experiment to address an urgent need for thermal chlorine nuclear data validation in plutonium systems. This urgent need is tied directly to plutonium recycle and recovery operations in the plutonium facility at Los Alamos National Laboratory, where exceptionally conservative criticality safety limits are used because no credit is taken for the neutron capture by chlorine. The experiment used weapons-grade plutonium metal plates clad in stainless steel, known as the PANN (plutonium aluminum no nickel) ZPPR (zero power physics reactor) plates. The plutonium was reflected and moderated by high-density polyethylene and included combinations of polyvinyl chloride (PVC) and chlorinated polyvinyl chloride (CPVC) as absorbers. The experiment and benchmark included three configurations mimicking 30 g 239 Pu/L plutonium, 300 g 239 Pu/L plutonium, and 600 g 239 Pu/L plutonium in an aqueous chloride solution. Uncertainties in the benchmark included five broad categories: (1) criticality measurement, (2) mass and density, (3) dimensions, (4) material compositions, and (5) positioning. The largest contribution to the overall uncertainties for all three cases came from the material compositions, in particular the PVC and CPVC absorber compositions. A detailed model was created to be a near match (that is within expectations of transport code users) and a simplified model was created to minimize offset dimensions and expedite modeling for code validation. Sample calculations were completed in MCNP6.3 with ENDF/B-VIII.0 and ENDF/B-VII.1 nuclear data. For the detailed and simplified models, the average difference between the computed and experimental k eff was 951 pcm. CWS will serve as the key validation experiment for nuclear criticality safety in support of aqueous chloride operations. The sensitivity to the chlorine capture cross section is orders of magnitude greater than other existing benchmarks. The current limits, as defined by nuclear criticality safety, are 520 g Pu per batch, i.e. the minimum critical mass of the Pu solution infinitely reflected by water [Criticality Handbook: Volume II, (1969)]. This extremely conservative critical mass limit does not credit any neutron capture by chlorine (in particular neutron capture by 35 Cl) and greatly impedes the throughput required for current and future operations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2026

DESI DR2 Galaxy luminosity functions

We present galaxy luminosity functions (LFs) for the Dark Energy Spectroscopic Instrument (DESI) DR2 Bright Galaxy Survey (BGS) in the g, r, z, and $w1$ bands over $0.002\lt z\lt 0.6$. Our analysis uses updated k-corrections and evolutionary corrections, including new polynomial kcorrection fits derived from BGS Year 1 data that supersede earlier GAMA-based prescriptions. Exploiting the statistical power of DESI, we measure LFs to very faint magnitudes, reaching $^{0.1}M_r-5\log h\sim -10$. Independent measurements from the North and South survey regions show excellent agreement around the LF knee, but the very small statistical uncertainties reveal that simple analytic forms fail to capture the full LF shape. The bright end departs from a pure exponential decline, while the faint end exhibits complex, non-powerlaw behaviour, including a pronounced upturn at $^{0.1}M_r-5\log h\gtrsim -15$, which is stronger for red galaxies than for blue. We show that our LFs are largely complete for galaxies with surface brightness $\mu _{50}\lt 25$, and that an apparent steepening fainter than $-13$ is driven primarily by local overdensity and fragmentation of large galaxies. A systematic North–South offset at the brightest magnitudes is traced to red galaxies and may reflect shallower North photometry underestimating extended earlytype profiles, although this remains inconclusive. We therefore also provide LFs based on model Petrosian magnitudes. Redshift splitting reveals small but significant residuals, indicating limitations of a simple global evolutionary model. Using the redshift limits of J. Loveday et al. (2012), we find excellent agreement with GAMA, with substantially reduced statistical errors. These measurements provide a precise reference for studies of environmental and population-dependent LFs and for testing galaxy formation models.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2024

The shard test and nanoporomechanics reverse classical paradigm of cement hydration being contractive

Le Chatelier in 1887 and Powers in 1947 demonstrated that the volume of nanoscale C-S-H (calcium silicate hydrate) particles formed during hydration is smaller than the combined volume of the reactants—the anhydrous Portland cement and water. Hydration has thus been considered as contractive. An experiment shows that the opposite is true above the nanoscale. The porous skeleton of cement paste expands as the growing C-S-H particles push each other apart, similar to crystal growth pressure. This is significant for high-performance concretes (HPC) with low water-cement ratios (w/c ≤ 0.4), where chemical self-desiccation lowers pore relative humidity by 40%, compared to just 1% in traditional concretes (w/c ≈ 0.5). Standard American Society for Testing and Materials (ASTM) C1608 tests, using 10 mm thick water-immersed specimens, show large shrinkage because the half-time of water ingress is many decades, unable to offset shrinkage-causing self-desiccation. The present experiment, using a laser microscopy-topography technique, proves the opposite—expansion, evidenced by measuring the length changes of water-immersed HPC shards 0.5 mm thick in which the diffusion halftime, only about one hour, allows continuous resaturation of pores, canceling self-desiccation. The faster diffusion (halftime of one hour) enables continuous pore resaturation, preventing shrinkage. When sealed with paraffin oil, the shards self-desiccate and shrink. These findings align with studies since 2015, showing that models excluding hydration expansion cannot fit test data across various specimen sizes and sealing conditions. The results suggest that standardized ASTM tests for the so-called chemical shrinkage in modern concretes with very low water-cement ratios are misleading and need revision.

Science & Technology - Other Topics↗

DOE OSTI2026

Rare earth element potential in coal and coal ash in the U.S. Gulf Coast

United States heavy reliance on imports of critical minerals (CMs), including rare earth elements (REEs), underscores the importance of development of domestic sources. The study objective was to quantify CM and REE concentrations in coal and coal ash in the US Gulf Coast region. CM and REE concentrations were measured for 118 samples from outcrops and 14 mines in the Gulf Coast. Results show that total REE + Yttrium (REY) concentrations (dry coal basis) are comparable to those of the upper continental crust (UCC) with localized hot spots, such as the Texas Gibbons Creek mine (REY ≤ ~ 2860 ppm). When normalized to UCC REY concentration (169 ppm, dry coal basis), REY to UCC ratios for Gulf Coast coal samples range from 0.1 to 17 (median ratio 0.6). REE extractability from lignites is high (median: 63%–93%) using environmentally benign weak acid. In addition to raw coal, coal ash from power plants could also serve as an REE source with a median ratio of REY in ash relative to coal of 4; however, extractability from coal ash is generally much lower (≤ 5% using the same weak acid as in coal). The median basket price for extracted REY as oxides from coal, assuming 70% extractability, is $\$3.2$ per tonne of coal and $\$186$ billion based on 58 billion metric tonnes of dry coal in the Gulf Coast. REEs important for magnets (Pr + Nd + Tb + Dy) account for ~ 80% of the total value. The corresponding median basket price for extracted REY as oxides from coal ash, assuming ~ 30% extractability, is ~$\$4.4$ per tonne of ash and $\$1.2$ billion based on 258 million tonnes of ash. REE production from coal would likely require co-products, such as activated carbon or humic acids, to attain economic viability. Production of REEs from coal ash could offset remediation costs related to potential water contamination. This reconnaissance study shows the potential for REE production from coal and coal ash in the Gulf Coast; however, carbon coproducts and/or societal benefits would likely be required for socioeconomic viability.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2026

An Analysis of Future Wind Energy Resources and Cost Uncertainties Across the United States

Wind power is a growing source of energy generation that relies on complex global atmospheric and earth system processes. There has been evidence of reductions in average wind speeds over land in North America since the 1980s, and several models project that average wind speeds will continue to decrease. Concurrently, the cost of wind energy systems in the United States has been decreasing since around 2010, a trend also projected to continue. There is considerable uncertainty in these future projections, with quantitative estimates of future wind resource and system costs varying widely. To study this, we run wind energy models with possible future system costs, turbine designs, and meteorological inputs from multiple downscaled earth system models over the contiguous United States. Changes in mean annual energy production from 2000-2019 to 2040-2059 can be as high as +10% in South Texas or as low as -20% in Iowa. Larger turbines and moderate reductions in system costs can offset the largest projected decreases in wind resource, but much uncertainty remains in the extent to which wind resources will change and to what extent system costs can be reduced. An analysis of variance shows, in several states in the Midwest, uncertainty in future wind resources can influence the cost of wind energy nearly as much as uncertainty in future system costs.

17 WIND ENERGY↗

DOE OSTI2025

DOE Zero Energy Ready Manufactured Housing: Subject Matter Expert Technical Assistance Summary

Manufactured homes offer American consumers an affordable option for decent single-family detached housing. For working-class American families in many U.S. markets, manufactured homes are the first step toward home ownership. They now make up 10% of all new homes constructed in the United States, with higher percentages in the south and in rural communities. To help encourage the production of homes that are more durable, healthy, efficient, and disaster resistant, the U.S. Department of Energy is bringing its building science research to the manufactured housing industry through DOE’s Zero Energy Ready Manufactured Home (ZER-MH) program, which provides technical assistance and voluntary guidelines to manufactured home builders. Homes built to these guidelines are better able to handle power outages and less likely to experience moisture issues, offering a better product option for American families. This higher quality is evidenced by energy modeling which shows homes manufactured to these voluntary guidelines will typically use half the energy of manufactured homes built to the current minimum requirements of the U.S. Department of Housing and Urban Development (HUD)’s Manufactured Housing and Construction Safety Standard (MHCSS). These homes can also reduce critical energy demand during the busiest hours of the day, typically late afternoon and early evening in the summer when air conditioning demand is highest and mornings in the winter when furnaces and heaters are heating up. Reducing electricity demand during these peak periods when electricity rates are at their highest reduces costs for American families while freeing up capacity on overburdened energy distribution networks. Builders participating in the DOE ZER-MH program are eligible for a tax incentive via the 45L tax credit, which helps to offset the costs of ZER-MH upgrades, enabling builders to offer these certified homes at no additional cost. Together these factors enable manufactured homes to offer home buyers a housing option that is both affordable to finance and affordable to operate, with lower monthly mortgage payments and lower monthly energy bills.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2024

Studying Wind Loading on CSP Collectors to Improve Performance and Reliability

Electricity generation through Concentrating Solar-thermal Power (CSP) adds the advantage of thermal energy storage and heat production. CSP collector costs constitute nearly one-third of total plant costs. Managing wind loading, especially dynamic wind loading caused by the turbulent wind flow, is a significant design challenge. Traditional collector designs rely on wind tunnel experiments and numerical simulations, which do not fully capture dynamic effects. Here, we provide an overview of NREL's activities on wind loading on CSP collectors, aiming to improve their reliability and cost-efficiency. We present insights from field measurements at operational parabolic trough and power-tower CSP plants. Over two years, we measured turbulent wind fields and resulting structural loads in a parabolic trough plant, revealing wind, turbulence, and collector field interactions. Similar measurements are ongoing at the Crescent Dunes heliostat field. These campaigns show how atmospheric turbulence, wind direction, and collector orientation affect dynamic wind loading. Upwind collector structures can generate turbulent structures, causing fluctuating loads at downstream collectors, impacting fatigue lifetime and optical efficiency. Preliminary results indicate that interior collectors experience higher turning moments than those at the edges, suggesting higher drive wear. At Crescent Dunes, we use instrumented heliostats at the field's edge and interior to study the translation of turbulent wind to dynamic structural loads. The campaign is still ongoing, and we will present first findings. Another focus of our work is tying the experimental wind loading findings to optical performance of the collectors, using simulation tools. For example, we derive torsional errors of the parabolic troughs - the angular offset from the sun position along a collector row. This error is impacted by wind-induced mirror deformations. Future work will focus on continuing the measurement efforts and combining them with computational fluid dynamic simulations. By providing detailed field measurements and validated models, our efforts aim to enhance understanding of wind loading on CSP collectors, improving their structural integrity and optical performance.

CSP↗

DOE OSTI2026

Cross-Linker Selection Controls Glass Transition Elevation or Reduction in Dynamic Covalently Bonded Polymer Networks

Introducing cross-links is a powerful approach to improve polymeric material performance relevant to controlling viscoelasticity, thermal and creep resistance, degradability, and efficient membrane separations. The chemically specific glass transition temperature T g is of fundamental importance in determining the time scales of key dynamical processes and physical state of the material in such applications. Here, we study experimentally how the introduction of relatively large cross-linking molecules in slowly exchanging dynamic bond-forming polymers (vitrimers) impacts vitrification for diverse polymer chemistries and a wide range of cross-link fractions. We find T g can increase, decrease, or even remain essentially unchanged, in qualitative contrast to the generic elevation of T g in traditional permanent polymer networks. We formulate an effective terpolymer network model to understand this rich behavior, which emerges as a consequence of a competition between pure cross-linking and generalized plasticization effects. The latter is associated with the tunable cross-linker size and intrinsic dynamic mobility that can offset slowing down due to traditional permanent cross-linking constraints. Here, a new strategy for functional polymer network design is suggested based on adjusting the relative importance of the two competing physical effects, which potentially can significantly enhance energy savings in applications while retaining other intrinsic properties germane to advanced materials performance.

Copolymers↗