Search NASA⌕ Search

SEARCH · Search NASA

Results for “Process improvement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Analyzing Discrepancies in a Software Development Project Change Request (CR) Assessment Process and Recommendations for Process Improvements

The Change Request (CR) assessment process is essential in the display development cycle. The assessment process is performed to ensure that the changes stated in the description of the CR match the changes in the actual display requirements. If a discrepancy is found between the CR and the requirements, the CR must be returned to the originator for corrections. Data was gathered from each of the developers to determine the type of discrepancies and the amount of time spent assessing each CR. This study sought to determine the most common types of discrepancies, and the amount of time required to assessing those issues. The study found that even though removing discrepancy before an assessment would save half the time needed to assess an CR with a discrepancy, the number of CR's found to have a discrepancy was very small compared to the total number of CR's assessed during the data gathering period.

Cunningham, Kenneth James↗
NASA NTRS1994

Software process improvement in the NASA software engineering laboratory

The Software Engineering Laboratory (SEL) was established in 1976 for the purpose of studying and measuring software processes with the intent of identifying improvements that could be applied to the production of ground support software within the Flight Dynamics Division (FDD) at the National Aeronautics and Space Administration (NASA)/Goddard Space Flight Center (GSFC). The SEL has three member organizations: NASA/GSFC, the University of Maryland, and Computer Sciences Corporation (CSC). The concept of process improvement within the SEL focuses on the continual understanding of both process and product as well as goal-driven experimentation and analysis of process change within a production environment.

Mcgarry, Frank↗
NASA NTRS1993

NCCDS configuration management process improvement

By concentrating on defining and improving specific Configuration Management (CM) functions, processes, procedures, personnel selection/development, and tools, internal and external customers received improved CM services. Job performance within the section increased in both satisfaction and output. Participation in achieving major improvements has led to the delivery of consistent quality CM products as well as significant decreases in every measured CM metrics category.

Shay, Kathy↗
NASA NTRS1988

Additives Improve Processing Of Polyimides

Melt-processable polyimides maintain desirable polymer properties prepared by adding small amounts of certain low-molecular-weight, thermally stable additives. Useful in preparing void-free polyimide composites from higher flow resins that wet out fibers at lower processing temperatures. Applied to preparing high-temperature polyimide adhesives allowing enhanced wetting of adherends and ultimately better adhesion. Improvement to processing polyimides and potential application for production of films, coatings, adhesives, and composites.

St. Clair, Terry L.↗
NASA NTRS2003

Ten steps to successful software process improvement

This paper identifies ten steps for managing change that address organizational and cultural issues. Four of these steps are critical, that if not done, will almost guarantee failure. This ten-step program emphasizes the alignment of business goals, change process goals, and the work performed by the employees of an organization.

software process improvement↗
DOE OSTI2026

Improving Process Level Understanding of Boundary Layer Winds over the Northeast U.S. Shelf: The Third Wind Forecast Improvement Project (WFIP3)

The third Wind Forecast Improvement Project (WFIP3), a U.S. Department of Energy and National Oceanic and Atmospheric Administration sponsored investigation, sought to improve understanding of the physical phenomena in the atmosphere and ocean that dictate the structure and variability of wind and thermodynamic fields within the marine atmospheric boundary layer. WFIP3 focused on mesoscale and submesoscale flows -- including sea breezes, low-level jets, low-level clouds, and coastal storms -- and the ability of advanced numerical model parameterizations to represent them within fully coupled oceanic and atmospheric modeling systems and foundational weather forecast models. WFIP3 conducted a comprehensive 18-month observational study over the Northeast U.S. outer continental shelf, a high-use coastal zone, using a 3D multiscale sensor array to highly resolve the temporal, vertical, and horizontal structure of the coupled atmospheric and oceanic boundary layers. Multiple land-based study sites adjacent to the coastal ocean observed surface meteorology and vertical profiles of atmospheric properties via passive infrared and microwave radiometers, active lidars and radars, and radiosondes. At sea, an array of surface flux buoys and two vertical profiling lidar buoys observed both atmospheric and oceanic properties, augmented by land-based oceanographic radar systems and routine ship-based surveys. Intensive observations of the marine atmospheric boundary layer over the ocean was done from an air-sea interaction flux tower and extended deployments of a large autonomous barge platform. Numerous critical forecasting phenomena were observed that are being evaluated within regional coupled and uncoupled modeling systems, including the National Oceanic and Atmospheric Administration's foundational High-Resolution Rapid Refresh forecast model.

Kirincich, Anthony↗
NASA NTRS2007

Development and Processing Improvement of Aerospace Aluminum Alloys

This final report, in multiple presentation format, describes a comprehensive multi-tasked contract study to improve the overall property response of selected aerospace alloys, explore further a newly-developed and registered alloy, and correlate the processing, metallurgical structure, and subsequent properties achieved with particular emphasis on the crystallographic orientation texture developed. Modifications to plate processing, specifically hot rolling practices, were evaluated for Al-Li alloys 2195 and 2297, for the recently registered Al-Cu-Ag alloy, 2139, and for the Al-Zn-Mg-Cu alloy, 7050. For all of the alloys evaluated, the processing modifications resulted in significant improvements in mechanical properties. Analyses also resulted in an enhanced understanding of the correlation of processing, crystallographic texture, and mechanical properties.

Lisagor, W. Barry↗
NASA NTRS2014

Infrastructure and Process Improvements After LADEE

The purpose of the Lunar Atmosphere Dust Environment Explorer (LADEE) mission was to measure the density, composition and time variability of the lunar dust environment. The successful mission launched Sept 7, 2013 and was de-orbited and impacted the moon's surface on April 17, 2014. The spacecraft had 3 primary science instruments, the Lunar Dust Experiment, Neutral Mass Spectrometer, and the Ultra Violet Spectrometer. The mission also had a Laser Communications payload that set a record download rate of 622 Mbps (megabits per second) from the moon orbit. The goal is to use the LADEE software base for upcoming smallsat missions. The onboard flight software for the mission was developed using a Model-Based Software methodology and agile software development practices. High level models were developed in Simulink, autocoded to C and layered on Core Flight Executive and Core Flight Software, VxWorks and required board support packages. Software package versions were frozen several years ago, and need to be brought to modern standards for future spacecraft missions. We are evaluating alternate Real Time Operating Systems and avionics architectures that comply with CubeSat form-factor and power limitations. In addition, the tool chain for the software development process has been improved. We will discuss the rationale, trades and implementation for the upgrade path after the LADEE mission.

Software Maintenance↗
NASA NTRS1986

Improved processing of Si3N4

A sintered Si3N4-SiO2-Y2O3 composition, NASA 6Y, was developed that reached four-point flexural average strength/standard deviation values of 857/36, 544/33, and 462/59 MPa at room temperature, 1200, and 1370 C, respectively. These strengths represented improvements of 56, 38, and 21 percent over baseline properties at the three test temperatures. At room temperature the standard deviation was reduced by more than a factor of three. These accomplishments were realized by the iterative utilization of conventional X-radiography to characterize structural (density) uniformity as affected by systematic changes in powder processing and sintering parameters. Accompanying the improvement in mechanical properties was a change in the type of flaw causing failure from a pore to a large columnar beta-Si3N4 grain typically 40 to 80 microns, 10 to 30 microns wide, and with an aspect ratio of 5:1.

Sanders, William A.↗
NASA NTRS2001

Lessons Learned and Process Improvement for Payload Operations at the Launch Site

For every space mission, there are challenges with the launch site/field operations process that are addressed too late in the development cycle. This potentially causes schedule delays, cost overruns, and adds risk to the mission success. This paper will discuss how a single interface, representing the payload at the launch site in all phases of development, will mitigate risk, and minimize or even alleviate potential problems later on. Experience has shown that a single interface between the project and the launch site allows for issues to be worked in a timely manner and bridges the gap between two diverse cultures.

Catena, John↗
NASA NTRS1999

Baselining the New GSFC Information Systems Center: The Foundation for Verifiable Software Process Improvement

This paper describes a study performed at the Information System Center (ISC) in NASA Goddard Space Flight Center. The ISC was set up in 1998 as a core competence center in information technology. The study aims at characterizing people, processes and products of the new center, to provide a basis for proposing improvement actions and comparing the center before and after these actions have been performed. The paper presents the ISC, goals and methods of the study, results and suggestions for improvement, through the branch-level portion of this baselining effort.

Parra, A.↗
NASA NTRSDate not supplied

Impacts of Improved Process Representation of Particle Dry Deposition on PM Pollution in a Global Chemistry-Climate Model: Differences Across Regions, Seasons, and PM Sizes

Dry deposition (DD) is a primary removal pathway of particulate matter (PM). The aerosol DD schemes in most global models do not reflect current mechanistic understanding gleaned from observations. The NASA GISS global chemistry-climate model has a new and more dynamic DD scheme that largely captures observed changes in deposition velocities with particle size. We quantify the response of simulated PM to changes in the DD scheme for the Northeast US, Central Europe, North China Plain, and Punjab. Relative to the widely used old scheme, the new scheme shows higher annual PM2.5 for all regions (up to +14%) except C. Europe where there are very small decreases. For PM1, annual increases occur over all regions (up to +20%). For PM10, there are decreases in C. Europe (-8%) and very small decreases in the NE US yet increases (up to +12%) in Punjab and N. China Plain. While there are always increases across seasons for Punjab and N. China Plain, there are both seasonal increases and decreases for the NE US and C. Europe. Given incomplete understanding of observed variations in deposition velocities for a given particle size, we perform sensitivity simulations that perturb the magnitude of the deposition velocities simulated by the new scheme. The annual PM response to increasing DD is similar in magnitude to decreasing DD, implying linearity in the PM sensitivity to DD. The relative annual response to perturbing the DD magnitude is weaker over Punjab and sometimes N. China Plain than the NE US and C. Europe. Higher PM over Punjab and N. China Plain implies a stronger sensitivity to DD when aerosol abundances are low. More mechanistic representation of aerosol DD can sometimes improve or worsen existing model PM biases, which suggests that PM biases due to other processes can be confounded or compounded by biases in DD. Further improvements to DD parameterizations require not only more observational constraints on aerosol deposition velocities but also an advanced understanding of the processes controlling observed variability.

Environmental pollution↗
DOE OSTI2025

Simultaneously Improving Process Efficiency and Mechanical Properties in Aluminum Alloys with Applied Magnetic Fields

In the aluminum heat treatment sector, large resistive batch furnaces are used for many heat treatment processes and are generally always running, operating at approximately 20–30% efficiency. The primary avenue for energy savings lies in shortening heat treatment times, which can be 24+ hours for solutionizing (450–625 °C) and aging treatments (150–250 ℃), depending on the alloy and specification requirements. The application of high magnetic fields (<9 T) has shown to significantly reduce aluminum alloy heat treatment times, while achieving enhanced mechanical properties. Here, we explore the effects of thermomagnetic processing on the heat treatment response of a commercial aluminum alloy A390.1. Heat treatment times were reduced by >80%, while achieving ~10% improvement in microhardness, and these improvements persisted after longer thermal exposures simulating use. The microstructural evolution and resulting properties will be discussed.

Kesler, Michael [ORNL] (ORCID:0000000161423128)↗
NASA NTRS2010

Process Improvement Through Tool Integration in Aero-Mechanical Design

Emerging capabilities in commercial design tools promise to significantly improve the multi-disciplinary and inter-disciplinary design and analysis coverage for aerospace mechanical engineers. This paper explores the analysis process for two example problems of a wing and flap mechanical drive system and an aircraft landing gear door panel. The examples begin with the design solid models and include various analysis disciplines such as structural stress and aerodynamic loads. Analytical methods include CFD, multi-body dynamics with flexible bodies and structural analysis. Elements of analysis data management, data visualization and collaboration are also included.

Integrated design and analysis↗
NASA NTRS2007

Development and Processing Improvement of Aerospace Aluminum Alloys-Development of AL-Cu-Mg-Ag Alloy (2139)

This final report supplement in presentation format describes a comprehensive multi-tasked contract study to continue the development of the silver bearing alloy now registered as aluminum alloy 2139 by the Aluminum Association. Two commercial scale ingots were processed into nominal plate gauges of two, four and six inches, and were extensively characterized in terms of metallurgical and crystallographic structure, and resulting mechanical properties. This report includes comparisons of the property combinations for this alloy and 2XXX and 7XXX alloys more widely used in high performance applications. Alloy 2139 shows dramatic improvement in all combinations of properties, moreover, the properties of this alloy are retained in all gauge thicknesses, contrary to typical reductions observed in thicker gauges of the other alloys in the comparison. The advancements achieved in this study are expected to result in rapid, widespread use of this alloy in a broad range of ground based, aircraft, and spacecraft applications.

Cho, Alex↗
NASA NTRS1993

WCSC environmental process improvement study and demonstration program

CSTAR's objective to develop commercial infrastructure is multi-faceted and includes diverse elements of the orbital and suborbital missions. Goals to this eight-month project with the WCSC are aimed at simplifying the environmental assessment, approval, and licensing process for commercial users. Included in this overarching set of goals are two specific processes: (1) air pollution control, and (2) the environmental assessment mechanism. Resolution of the potentially user unfriendly aspects of these environmentally sensitive criteria are readily transferable to other ranges where commercial space activity will be supported.

Pawlick, Joseph F., Jr.↗
NASA NTRS1994

Environmental process improvement feasibility study and demonstration program

This report is the final product of an environmental study conducted by Western Commercial Space Center, Inc. under contract to Tennessee-Calspan Center for Space Transportation and Applied Research. The purpose of this investigation is to accurately document the current environmental and permitting processes associated with commercial space launch activity at Vandenberg AFB, and make recommendations to streamline those processes. The particular areas of interest focus on: identifying applicable Federal, state, and local laws, Department of Defense directives, and Air force regulations; defining the environmental process on Vandenberg AFB and how it relates with other agencies, including Federal and state regulatory agencies; and defining the air quality permit process. Study investigation results are applied to an example Pilot Space Launch Vehicle (PSLV) planning to launch from Vandenberg AFB. The PSLV space hardware is analyzed with respect to environmental and permitting issues associated with vehicle processing, facilities required (existing or new), and launch. The PSLV verified the earlier findings of the study and gave insight into streamlining recommendations.

Martin, Rodger L.↗