Search NASA⌕ Search

SEARCH · Search NASA

Results for “Proper Orthogonal Decomposition (POD)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Experimental Measurements of the Wake of a Sphere at Subcritical Reynolds Numbers

This work experimentally investigated the flow phenomena and vortex structures in the wake of a sphere located in a water loop at Reynolds numbers of Re = 850, 1,250, and 1,700. Velocity fields in the wake region were obtained by applying the time-resolved stereoscopic particle image velocimetry (TR-SPIV) technique. From the acquired TR-SPIV velocity vector fields, the statistical values of mean and fluctuating velocities were computed. Spectral analysis, two-point velocity–velocity cross-correlation, proper orthogonal decomposition (POD) and vortex identification analyses were also performed. The velocity fields show a recirculation region that decreases in length with an increase of Reynolds numbers. The power spectra from the spectral analysis had peaks corresponding to a Strouhal number of St = 0.2, which is a value commonly found in the literature studies of flow over a sphere. The two-point cross-correlation analysis revealed elliptical structures in the wake, with estimated integral length scales ranging between 12% and 63% of the sphere diameter. The POD analysis revealed the statistically dominant flow structures that captured the most flow kinetic energy. It is seen that the flow kinetic energy captured in the smaller scale flow structures increased as Reynolds number increased. The POD modes contained smaller structure as the Reynolds number increased and as mode order increased. In addition, spectral analysis performed on the POD temporal coefficients revealed peaks corresponding to St = 0.2, similar to the spectral analysis on the fluctuating velocity. The ability of POD to produce low-order reconstructions of the flow was also utilized to facilitate vortex identification analysis, which identified average vortex sizes of 0.41D for Re1, 0.33D for Re2, and 0.32D for Re3.

Engineering↗
DOE OSTI2024

S-OPT: A Points Selection Algorithm for Hyper-Reduction in Reduced Order Models

While projection-based reduced order models can reduce the dimension of full order solutions, the resulting reduced models may still contain terms that scale with the full order dimension. Hyper-reduction techniques are sampling-based methods that further reduce this computational complexity by approximating such terms with a much smaller dimension. The goal of this work is to introduce the points selection algorithm developed by Shin and Xiu as a hyper-reduction method. The selection algorithm was originally proposed as a stochastic collocation method for uncertainty quantification. Since the algorithm aims at maximizing a quantity $\mathcal{S}$ that measures both the column orthogonality and the determinant, we refer to the algorithm as S-OPT. Numerical examples are provided to demonstrate the performance of S-OPT and to compare its performance with a gappy proper orthogonal decomposition (POD) algorithm. Here, we found that using the S-OPT algorithm is shown to predict the full order solutions with higher accuracy than gappy POD especially when the number of sampling points is small, although we note that S-OPT shows slow asymptotic convergence with respect to the number of samples for some applications, e.g., Lagrangian hydrodynamics.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

DT-HYDRO

The software solves the time dependent, one dimensional (1D) coupled mass and momentum balance equations governing the elastic flow of water through the penstock, turbine and draft tube in a hydroelectric facility using a high order finite volume based method. The numerical method is based on the Kurganov-Tadmor central method paired with the Monotonic Upstream-centered Scheme for Conservation Laws (MUSCL). This solution method accurately resolves the fast transient behavior of the flow, including water hammer. Additionally, the software estimates the full 3D flow field within the turbine chamber in real time, a feat that is made possible by leveraging pre-computed CFD results by utilizing a reduced order modeling method based on an efficient randomized singular value decomposition (SVD) driven proper orthogonal decomposition (POD) with POD-mode weight regression. The reduced order model of the 3D flow is directly coupled to the 1D elastic flow model so the entire flow field through the penstock and turbine system is resolved quickly and with high fidelity.

Gurecky, William [Oak Ridge National Laboratory (O↗
DOE OSTI2024

Thermal field reconstruction and compressive sensing using proper orthogonal decomposition

Model order reduction allows critical information about sensor placement and experiment design to be distilled from raw fluid mechanics simulation data. In many cases, sensed information in conjunction with reduced order models can also be used to regenerate full field variables. In this paper, a proper orthogonal decomposition (POD) inferencing method is extended to the modeling and compressive sensing of temperature, a scalar field variable. The method is applied to a simulated, critically stable, incompressible flow over a heated cylinder (Re = 1000) with Prandtl number varying between 0.001 and 50. The model is trained on pressure and temperature data from simulations. Field reconstructions are then generated using data from selected sensors and the POD model. Finally, the reconstruction error is evaluated across all Prandtl numbers for different numbers of retained modes and sensors. The predicted trend of increasing reconstruction accuracy with decreasing Prandtl number is confirmed and a Prandtl number/sensor count error matrix is presented.

Matulis, John↗
DOE OSTI2022

Augmented reduced order models for turbulence

The authors introduce an augmented-basis method (ABM) to stabilize reduced-order models (ROMs) of turbulent incompressible flows. The method begins with standard basis functions derived from proper orthogonal decomposition (POD) of snapshot sets taken from a full-order model. These are then augmented with divergence-free projections of a subset of the nonlinear interaction terms that constitute a significant fraction of the time-derivative of the solution. The augmenting bases, which are rich in localized high wavenumber content, are better able to dissipate turbulent kinetic energy than the standard POD bases. Several examples illustrate that the ABM significantly out-performs L 2 -, H 1 - and Leray-stabilized POD ROM approaches. The ABM yields accuracy that is comparable to constraint-based stabilization approaches yet is suitable for parametric model-order reduction in which one uses the ROM to evaluate quantities of interests at parameter values that differ from those used to generate the full-order model snapshots. Several numerical experiments point to the importance of localized high wavenumber content in the generation of stable, accurate, and efficient ROMs for turbulent flows.

Kaneko, Kento↗
DOE OSTI2022

Implications of Shear and Thermal Stratification on Wind Turbine Tip-Vortex Stability

The interaction between wind turbines in a wind farm through their wakes is a phenomenon that has been studied for decades and is still relevant today. Turbines clustered together in arrays will often operate in the wake of other upstream turbines which may lead to significant power losses and fatigue loads. For modern large-scale wind turbines, the mean shear velocity profile and thermal stratification are major components of the atmospheric boundary layer so it is important to understand their impact on near-wake development. Additionally, veer is present due to the rotation of the Earth. The impact of shear, thermal stratification and veer on the stable wake length of turbines with a dynamic control strategy is studied numerically in this work using a suite of highly resolved large-eddy simulations. Instantaneous flow fields are extracted from the simulations and used to conduct proper orthogonal decomposition (POD) and compute the mean kinetic energy fluxes by different POD modes to better understand the tip-vortex instability mechanisms. Our findings show that the dynamic pitch control scheme is able to shorten the stable wake length to about 1.5R in uniform flow. Shear can significantly affect the break up of wind turbine tip-vortices as well as the shape and stable length of the wake, whereas thermal stratification seems to only have limited contribution to the spatial development of the near-wake field. Veer causes the wake boundary to skew but has a limited impact on the wake length.

length thermal stratification↗
DOE OSTI2022

Neutron diffusion calculation in heterogeneous geometry based on local/global iteration using proper orthogonal decomposition

This study newly proposes a heterogeneous core calculation method based on local/global iteration using proper orthogonal decomposition (POD). By using the singular value decomposition (SVD) and the low-rank approximation, appropriate POD bases for expanding the neutron flux can be obtained from snapshot data of the neutron flux obtained by fine mesh calculations. By projection using the POD bases, the dimension of the target equation (e.g., discretized neutron diffusion equation) can be dramatically reduced. In the proposed method, POD is effectively applied to each single assembly calculation (local calculation). Furthermore, using the local/global iteration, the effective neutron multiplication factor and the neutron flux distribution in the whole core geometry can be obtained by combining the numerical results of the local calculation for each fuel assembly and the global calculation for the whole core. As a feasibility study, the proposed method is applied to a one-dimensional heterogeneous core analysis, and the accuracy is investigated by changing the total number of POD bases. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

A COUPLED DETERMINISTIC TRANSPORT CALCULATION IN COMSOL USING PROPER ORTHOGONAL DECOMPOSITION

A coupled physics problem consisting of radiation transport and heat transfer was modeled using COMSOL Multiphysics to simulate a criticality accident. Reduced order models (ROM) were created to accelerate the radiation transport calculation through Proper Orthogonal Decomposition (POD). Additionally, on-the-fly neutron cross sections were generated from a non-linear function through a feed forward neural network. The Livelink for MATLAB module allowed for data transfer between an otherwise independent solver and in-house modules. A data driven approach to POD was developed to act as a surrogate model to couple with heat transfer, with the POD module written in MATLAB coupled to an isolated heat transfer solve in COMSOL. A coupled transient solution resulted in a good approximation of the flux and temperature, with the maximum error being 3E-2 and 2.5E-3 respectively.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Canonical and noncanonical Hamiltonian operator inference

Here, a method for the nonintrusive and structure-preserving model reduction of canonical and noncanonical Hamiltonian systems is presented. Based on the idea of operator inference, this technique is provably convergent and reduces to a straightforward linear solve given snapshot data and gray-box knowledge of the system Hamiltonian. Examples involving several hyperbolic partial differential equations show that the proposed method yields reduced models which, in addition to being accurate and stable with respect to the addition of basis modes, preserve conserved quantities well outside the range of their training data.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Machine Learning Assisted Safety Modeling and Analysis of Advanced Reactors

With the advances in computational power and numerical methods, analysts can now rely on first-principle simulations to predict ultra-fine details in a variety of applications. Advances in machine learning (ML) have produced algorithms that can now learn high-level abstractions via hierarchical models. This project aims to leverage advances in ML techniques and the available high-resolution simulation data to develop a novel modeling and simulation (M\&S) methodology for reactor safety analysis. While application-agnostic ML techniques are available, complex physics constraints need to be incorporated into ML techniques to build ML-based closures for computationally efficient predictive simulations. This project intends to develop a physics-guided data-driven multi-scale methodology for M\&S of advanced reactors. The project focuses on thermal fluid (T/F) phenomena, which play major roles in advanced reactor safety. Specifically, we propose a data-driven coarse-mesh turbulence model based on local flow features for the transient analysis of thermal mixing and stratification in a sodium-cooled fast reactor (SFR). The model has a coarse-mesh setup to ensure computational efficiency, while it is trained by fine-mesh computational fluid dynamics (CFD) data with Reynolds-averaged Navier-Stokes (RANS) turbulence model to ensure accuracy. Three different neural networks are developed and tested for loss-of-flow transients in the hot pool of SFR, i.e. the densely connected convolutional neural network (DCNN), long-short-term-memory network based on proper orthogonal decomposition (POD-LSTM), and the DCNN informed by LSTM (DCNN-LSTM). The performances of these three neural networks are evaluated based on baseline models. The DCNN-LSTM model has been chosen for further hyperparameter optimization. Furthermore, based on a simplified two-dimensional case, uncertainty quantification (UQ) of the developed ML-based closure are investigated with three methods, i.e. Monte Carlo dropout, deep ensemble, and Bayesian neural network. The developed ML-based turbulent viscosity closure relation based on deep ensemble is then integrated into the system analysis module SAM and serves as a term in the conservation equations. Such a SAM-ML based procedure guarantees that the obtained results are consistent with the physical constraints of the thermal-fluid system. The SAM-ML simulation on the same loss-of-flow transient showed comparable accuracy with the CFD simulation but with a much coarser mesh setup. Last but not least, the ML-based closure improvement with the support of higher-fidelity data from large eddy simulation (LES) is discussed. As a first step towards this direction, a baseline LES simulation is performed to obtain comparable data with RANS results. Based on the early results, future investigation on further improving the ML-based closure is discussed. We believe the developed approach that combines scientific machine learning with nuclear system analysis code can benefit the advanced reactor community as more accurate safety analyses will better characterize reactor safety margins and reduce licensing efforts.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Towards Reconstruction of Complex Flow Fields Using Unit Flows

Many complex turbulent flows in nature and engineering can be qualitatively regarded as being constituted of multiple simpler unit flows. The objective of this work is to characterize the coherent structures in such complex flows as a combination of constituent unitary flow structures for the purpose of reduced-order representation. While turbulence is clearly a non-linear phenomenon, we aim to establish the degree to which the optimally weighted superposition of unitary flow structures can represent the complex flow structures. The rationale for investigating such superposition stems from the fact that the large-scale coherent structures are generated by underlying flow instabilities that may be reasonably described using linear analysis. Clearly, the degree of validity of superposition will depend on the flow under consideration. In this work, we take the first step toward establishing a procedure for investigating superposition. Experimental data of single and triple tandem jets in crossflow are used to demonstrate the procedure. A composite triple tandem jet flow field is generated from optimal superposition of single jet data and compared against ‘true’ triple jet data. Direct comparisons between the true and composite fields are made for spatial, temporal, and kinetic energy content. The large-scale features (obtained from proper orthogonal decomposition or POD) of true and composite tandem jet wakes exhibit nearly 70% agreement in terms of modal eigenvector correlation. Corresponding eigenvalues reveal that the kinetic energy of the flow is also emulated with only a slight overprediction. Temporal frequency features are also examined in an effort to completely characterize POD modes. The proposed method serves as a foundation for more rigorous and robust dimensional reduction in complex flows based on unit flow modes.

Kristo, Paul J.↗
DOE OSTI2021

Discrete Empirical Interpolation Method Based Dynamic Load Model Reduction

Dynamic load models add significant complexity to bulk power system time-domain simulations. The complexity is due to the large number of ordinary differential equations (ODEs) introduced by the dynamic load components such as induction motors. It is challenging to derive reduced-order models (ROMs) for dynamic loads due to the nonlinear functions in their governing equations. This paper applies the discrete empirical interpolation method enhanced proper orthogonal decomposition (DEIM-POD) to approximate the full dynamic load model with the ROM that minimizes the projection error of the nonlinear functions in dynamic load ODEs onto their dominant modes. This approach only requires evaluation of nonlinear functions at selected observation points. The observation points selected by DEIM also provide information for screening critical load buses where dynamic load model parameters contribute the most to the accuracy of ROM across multiple contingencies. The proposed approach is validated on IEEE 9-bus, WECC 179-bus and 2384-bus Polish systems.

bulk power system↗
DOE OSTI2023

Proper orthogonal descriptors for efficient and accurate interatomic potentials

Here, we present the proper orthogonal descriptors for efficient and accuracy representation of the potential energy surface. The potential energy surface is represented as a many-body expansion of parametrized potentials in which the potentials are functions of atom positions and parameters. The proper orthogonal decomposition is employed to decompose the parametrized potentials into a set of proper orthogonal descriptors (PODs). Because of the rapid convergence of the proper orthogonal decomposition, relevant snapshots can be sampled exhaustively to represent the atomic neighborhood environment accurately with a small number of descriptors. The proper orthogonal descriptors are used to develop interatomic potentials by using a linear expansion of the descriptors and determining the expansion coefficients from a weighted least-squares regression against a density functional theory (DFT) training set. We present a comprehensive evaluation of the POD potentials on previously published DFT data sets comprising Li, Mo, Cu, Ni, Si, Ge, and Ta elements. The data sets represent a diverse pool of metals, transition metals, and semiconductors. The accuracy of the POD potentials are comparable to that of state-of-the-art machine learning potentials such as the spectral neighbor analysis potential (SNAP) and the atomic cluster expansion (ACE).

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Data-Driven Reduced-Order Modeling of Convective Heat Transfer in Porous Media

This work presents a data-driven Reduced-Order Model (ROM) for parametric convective heat transfer problems in porous media. The intrusive Proper Orthogonal Decomposition aided Reduced-Basis (POD-RB) technique is employed to reduce the porous medium formulation of the incompressible Reynolds-Averaged Navier–Stokes (RANS) equations coupled with heat transfer. Instead of resolving the exact flow configuration with high fidelity, the porous medium formulation solves a homogenized flow in which the fluid-structure interactions are captured via volumetric flow resistances with nonlinear, semi-empirical friction correlations. A supremizer approach is implemented for the stabilization of the reduced fluid dynamics equations. The reduced nonlinear flow resistances are treated using the Discrete Empirical Interpolation Method (DEIM), while the turbulent eddy viscosity and diffusivity are approximated by adopting a Radial Basis Function (RBF) interpolation-based approach. The proposed method is tested using a 2D numerical model of the Molten Salt Fast Reactor (MSFR), which involves the simulation of both clean and porous medium regions in the same domain. For the steady-state example, five model parameters are considered to be uncertain: the magnitude of the pumping force, the external coolant temperature, the heat transfer coefficient, the thermal expansion coefficient, and the Prandtl number. For transient scenarios, on the other hand, the coastdown-time of the pump is the only uncertain parameter. The results indicate that the POD-RB-ROMs are suitable for the reduction of similar problems. The relative L2 errors are below 3.34% for every field of interest for all cases analyzed, while the speedup factors vary between 54 (transient) and 40,000 (steady-state).

German, Péter (ORCID:0000000307285283)↗
DOE OSTI2022

GeN-ROM—An OpenFOAM®-based multiphysics reduced-order modeling framework for the analysis of Molten Salt Reactors

This work presents a projection-based multiphysics Model Order Reduction (MOR) framework for the analysis of nuclear systems and its application to parametric simulations of Molten Salt Reactors (MSR). The framework, named GeN-ROM, is developed using OpenFOAM® and employs a Proper Orthogonal Decomposition aided Reduced-Basis technique (POD-RB). It can be used to reduce steady-state and transient multiphysics problems involving parametric fluid dynamics, heat exchange, and neutronics phenomena. For the treatment of structural elements in the hydraulic systems, a porous medium approach has been adopted. The reduction process is data-driven and snapshot information is extracted via POD to learn the solution manifold and to build global spatial basis functions. At the data collection phase, GeN-ROM makes use of the solvers available in GeN-Foam, a similarly OpenFOAM®-based multiphysics framework developed for the analysis of nuclear reactors. The global bases are used both to approximate the solution fields and to project the full-order equations onto lower-dimensional subspaces, thus considerably reducing the number of unknowns in a numerical system. This reduction leads to significant computational speedups, which is ideal for multi-query applications such as uncertainty quantification or design optimization. The developed tool has been tested using a 2D multiphysics model of the Molten Salt Fast Reactor (MSFR) with steady-state and transient scenarios, with speedups on the order of 10 – 10 5 .

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Parametric model-order-reduction development for unsteady convection

A time-averaged error indicator with POD- h Greedy is developed to drive parametric model order reduction (pMOR) for 2D unsteady natural convection in a high-aspect ratio slot parameterized with the Prandtl number, Rayleigh number, and slot angle with respect to the gravity. The error indicator is extended to accommodate the energy equation and Leray regularization. Despite being two-dimensional and laminar, the target flow regime presents several challenges: 1) there is a bifurcation in the angle parameter space; 2) the solution can be multivalued, even at steady state; and 3) the solution exhibits spatio-temporal chaos at several points in the parameter space. The authors explore several reduced-order models (ROMs) and demonstrate that Leray-regularized Galerkin ROMs provide a robust solution approach for this class of flows. They further demonstrate that error-indicated pMOR can efficiently predict several QOIs, such as mean flow, mean Nusselt number and mean turbulent kinetic energy, even in the presence of a bifurcation. Finally, they show that spatio-temporal chaos can lead to lack of reproducibility in both the full-order model and the reduced-order model and that the variance in the full-order model provides a lower bound on the pMOR error in these cases.

leray regularization↗
DOE OSTI2021

Parallelized POD-based suboptimal economic model predictive control of a state-constrained Boussinesq approximation

Motivated by an energy efficient building application, we want to optimize a quadratic cost functional subject to the Boussinesq approximation of the Navier-Stokes equations and to bilateral state and control constraints. Since the computation of such an optimal solution is numerically costly, we design an efficient strategy to compute a sub-optimal (but applicationally acceptable) solution with significantly reduced computational effort. We employ an economic Model Predictive Control (MPC) strategy to obtain a feedback control. The MPC sub-problems are based on a linear-quadratic optimal control problem subjected to mixed control and state constraints and a convection-diffusion equation, reduced with proper orthogonal decomposition. Finally, to solve each sub-problem, we apply a primal-dual active set strategy. The method can be fully parallelized, which enables the solution of large problems with real-world parameters.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Analysis of combustion acoustic phenomena in compression–ignition engines using large eddy simulation

As computational capabilities continue to grow, exploring the limits of computational fluid dynamics to capture complex and elusive phenomena, which are otherwise difficult to study by experimental techniques, is one of the main targets for the research community. This paper presents a detailed analysis of the physical processes that lead to combustion noise emissions in internal combustion engines. In particular, diesel combustion in a compression-ignition (CI) engine is studied in order to understand the singular behavior of the in-cylinder flow field responsible for the acoustic emissions. The main objective is, therefore, to improve the understanding of the phenomena involved in CI engine noise using large eddy simulations. Several visualization methods are employed to investigate the connection between combustion behavior and its effects on the pressure field. In addition, proper orthogonal decomposition is used to analyze the modal energy distribution among all the acoustic modes. The results show that the acoustic signature is fundamentally conditioned by the intensity of the premixed combustion rather than by the pressure oscillations generated by turbulent fluctuations in the flame surface established during the diffusion stage.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗