Search NASA⌕ Search

SEARCH · Search NASA

Results for “ROLLING MOMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

The Real-Time Wall Interference Correction System of the NASA Ames 12-Foot Pressure Wind Tunnel

An improved version of the Wall Signature Method was developed to compute wall interference effects in three-dimensional subsonic wind tunnel testing of aircraft models in real-time. The method may be applied to a full-span or a semispan model. A simplified singularity representation of the aircraft model is used. Fuselage, support system, propulsion simulator, and separation wake volume blockage effects are represented by point sources and sinks. Lifting effects are represented by semi-infinite line doublets. The singularity representation of the test article is combined with the measurement of wind tunnel test reference conditions, wall pressure, lift force, thrust force, pitching moment, rolling moment, and pre-computed solutions of the subsonic potential equation to determine first order wall interference corrections. Second order wall interference corrections for pitching and rolling moment coefficient are also determined. A new procedure is presented that estimates a rolling moment coefficient correction for wings with non-symmetric lift distribution. Experimental data obtained during the calibration of the Ames Bipod model support system and during tests of two semispan models mounted on an image plane in the NASA Ames 12 ft. Pressure Wind Tunnel are used to demonstrate the application of the wall interference correction method.

Ulbrich, Norbert↗
NASA NTRS1990

Analysis of a six-component, flow-through, strain-gage, force balance used for hypersonic wind tunnel models with scramjet exhaust flow simulation

The thermal effects of simulant gas injection and aerodynamic heating at the model's surface on the measurements of a non-watercooled, flow through balance were investigated. A stainless steel model of a hypersonic air breathing propulsion cruise missile concept (HAPCM-50) was used to evaluate this balance. The tests were conducted in the 20-inch Mach 6 wind tunnel at NASA-Langley. The balance thermal effects were evaluated at freestream Reynolds numbers ranging from .5 to 7 x 10(exp 6) ft and angles of attack between -3.5 to 5 deg at Mach 6. The injection gases considered included cold air, hot air, and a mixture of 50 percent Argon and 50 percent Freon-12. The stagnation temperatures of the cold air, hot air, and Ar-Fr(12) reached 111, 214, and 283 F, respectively within the balance. A bakelite sleeve was inserted into the inner tube of the balance to minimize the thermal effects of these injection gases. Throughout the tests, the normal force, side force, yaw moment, roll moment, and pitching moment balance measurements were unaffected by the balance thermal effects of the injection gases and the wind tunnel flow. However, the axial force (AF) measurement was significantly affected by balance heating. The average zero shifts in the AF measurements were 1.9, 3.8, and 5.9 percent for cold air, hot air, and Ar-Fr(12) injection, respectively. The AF measurements decreased throughout these tests which lasted from 70 to 110 seconds. During the cold air injection tests, the AF measurements were accurate up to at least ten seconds after the model was injected into the wind tunnel test section. For the hot air and Ar-Fr(12) tests, the AF measurements were accurate up to at least five seconds after model injection.

Kniskern, Marc W.↗
NASA NTRS1996

Aerodynamic Characteristics of an Aerospace Vehicle During a Subsonic Pitch-Over Maneuver

Time-dependent CFD has been used to predict aerospace vehicle aerodynamics during a subsonic rotation maneuver. The inviscid 3D3U code is employed to solve the 3-D unsteady flow field using an unstructured grid of tetrahedra. As this application represents a challenge to time-dependent CFD, observations concerning spatial and temporal resolution are included. It is shown that even for a benign rotation rate, unsteady aerodynamic effects are significant during the maneuver. Possibly more significant, however, the rotation maneuver creates ow asymmetries leading to yawing moment, rolling moment, and side force which are not present in the quasi-steady case. A series of steady solutions at discrete points in the maneuver are also computed for comparison with wind tunnel measurements and as a means of quantifying unsteady effects.

Kleb, William L.↗
NASA NTRS1954

Method for calculating the rolling and yawing moments due to rolling for unswept wings with or without flaps or ailerons by use of nonlinear section lift data

The methods of NACA reports 865 and 1090 have been applied to the calculation of the rolling-moment and yawing-moment coefficients due to rolling for unswept wings with or without flaps or ailerons. The methods are based on lifting-line theory and allow the use of nonlinear section lift data. The method presented in this report permits calculations to be made somewhat beyond maximum lift for wings having no twist or continuous twist and employing airfoil sections which do not display large discontinuities in the lift curves. Calculations can be made up to maximum lift for wings with discontinuous twist such as that produced by partial-span flaps or ailerons, or both. Two calculated examples are presented in simplified computing forms in order to illustrate the procedures involve.

Martina, Albert P↗
NASA NTRS1954

Experimental investigation of the forces and moments due to sideslip of a series of triangular vertical and horizontal tail combinations at Mach numbers

An experimental investigation was made at Mach numbers of 1.62, 1.93, and 2.41 of a series of tail combinations consisting of triangular vertical tail attached symmetrically to a triangular horizontal tail to determine the lateral force, yawing moment, and rolling moment due to sideslip. The apex angles of both the vertical- and horizontal-tail surfaces were varied systematically in order to obtain results for an appreciable range of operating conditions. The results of the investigation indicated that, for tails having subsonic leading edges and supersonic trailing edges, the lateral-force derivative and the yawing-moment derivative were predicted satisfactorily by the method presented in NACA TN 3071 except when the leading edges approach a sonic condition. The theoretical rolling-moment derivative was in fair agreement with the experimental derivative. For the limited tests in which both the leading and trailing edges were supersonic, the prediction of the lateral-force derivative and the yawing-moment derivative obtained from NACA TN 2412 was in good agreement with the experimental derivatives, whereas the prediction of the rolling-moment derivative was fair.

Coletti, Donald E↗
NASA NTRS1953

Method for calculating the rolling and yawing moments due to rolling for unswept wings with or without flaps or ailerons by use of nonlinear section lift data

The methods of NACA Reports 865 and 1090 have been applied to the calculation of the rolling- and yawing-moment coefficients due to rolling for unswept wings with or without flaps or ailerons. The methods allow the use of nonlinear section lift data together with lifting-line theory. Two calculated examples are presented in simplified computing forms in order to illustrate the procedures involved.

CONTROLS - COMPLETE WINGS↗
NASA NTRS1959

Static Stability and Control Characteristics of a 0.5-Scale Model of the Hughes GAR-11 Missile at Mach Numbers from 1.60 to 2.30

Normal forces, axial forces, pitching moments, and rolling moments on the model and hinge moments on each of the four control surfaces were measured. Control surfaces were deflected from -35 deg to 15 deg in various combinations to produce pitching, yawing, and rolling moments on the model over a range of angles of attack from -5 deg to 25 deg at roll angles from -135 deg to 45 deg.

Wong, Norman D.↗
NASA NTRS1976

Application of the nonlinear vortex-lattice concept to aircraft-interference problems

A discrete-vortex model was developed to account for the hazardous effects of the vortex trail issued from the edges of separation of a large leading wing on a small trailing wing. The model is divided into three main parts: the leading wing and its near wake, the near and far wakes of the leading wing, and the trailing wing and the portion of the far wake in its vicinity. The normal force, pitching moment, and rolling moment coefficients for the trailing wing are calculated. The circulation distribution in the vortex trail is calculated in the first part of the model where the leading wing is far upstream and hence is considered isolated. A numerical example is solved to demonstrate the feasibility of using this method to study interference between aircraft. The numerical results show the correct trends: The following wing experiences a loss in lift between the wing-tip vortex systems of the leading wing, a gain outside this region, and strong rolling moments which can change sign as the lateral relative position changes. All the results are strongly dependent on the vertical relative position.

Kandil, O. A.↗
NASA NTRS1990

An experimental study of the nonlinear dynamic phenomenon known as wing rock

An experimental investigation into the physical phenomena associated with limit cycle wing rock on slender delta wings has been conducted. The model used was a slender flat plate delta wing with 80-deg leading edge sweep. The investigation concentrated on three main areas: motion characteristics obtained from time history plots, static and dynamic flow visualization of vortex position, and static and dynamic flow visualization of vortex breakdown. The flow visualization studies are correlated with model motion to determine the relationship between vortex position and vortex breakdown with the dynamic rolling moments. Dynamic roll moment coefficient curves reveal rate-dependent hysteresis, which drives the motion. Vortex position correlated with time and model motion show a time lag in the normal position of the upward moving wing vortex. This time lag may be the mechanism responsible for the hysteresis. Vortex breakdown is shown to have a damping effect on the motion.

Arena, A. S., Jr.↗
NASA NTRS1994

Status of MSBS study at NAL

Two Magnetic Suspension and Balance Systems (MSBS) at the National Aerospace Laboratory (NAL) in Japan are introduced. They are the 10 cm MSBS and the 60 cm MSBS. They have 10 cm x 10 cm and 60 cm x 60 cm test sections. The control of suspending a model at the 10 cm MSBS is six degrees of freedom including the rolling moment control. The model for the rolling moment control has two pairs of small extra permanent magnets at both its ends plus a main cylindrical magnet. The rolling moment is generated by the magnetic forces acting on the extra magnets by controlled current passing through the four side coils independently. Test results show the roll angle of the model is controlled in this way. The dynamic calibration test was carried out at the MSBS in five degrees of freedom without the rolling moment control. The model is a simple cylindrical magnet magnetized along its axis. The obtained results show that the dynamic calibration with measured magnetic field intensity is much superior to that with the coil currents. The 60 cm MSBS was designed with some data obtained at the 10 cm one. It is fundamentally proportional to the 10 cm one in size and coil positions. The measured magnetic field intensity is not so strong as expected at design. It was operated first in 1993. The control is three degrees of freedom in the longitudinal direction.

Sawada, Hideo↗
NASA NTRS1996

X-29A Lateral-Directional Stability and Control Derivatives Extracted From High-Angle-of-Attack Flight Data

The lateral-directional stability and control derivatives of the X-29A number 2 are extracted from flight data over an angle-of-attack range of 4 degrees to 53 degrees using a parameter identification algorithm. The algorithm uses the linearized aircraft equations of motion and a maximum likelihood estimator in the presence of state and measurement noise. State noise is used to model the uncommanded forcing function caused by unsteady aerodynamics over the aircraft at angles of attack above 15 degrees. The results supported the flight-envelope-expansion phase of the X-29A number 2 by helping to update the aerodynamic mathematical model, to improve the real-time simulator, and to revise flight control system laws. Effects of the aircraft high gain flight control system on maneuver quality and the estimated derivatives are also discussed. The derivatives are plotted as functions of angle of attack and compared with the predicted aerodynamic database. Agreement between predicted and flight values is quite good for some derivatives such as the lateral force due to sideslip, the lateral force due to rudder deflection, and the rolling moment due to roll rate. The results also show significant differences in several important derivatives such as the rolling moment due to sideslip, the yawing moment due to sideslip, the yawing moment due to aileron deflection, and the yawing moment due to rudder deflection.

Iliff, Kenneth W.↗
NASA NTRS1958

Wind-Tunnel Investigation of the Low-Speed Characteristics of a 1/8-Scale Model of the Republic XP-91 Airplane with a Vee and a Conventional Tail. Addendum - Characteristics with a Revised Conventional Tail and Drooped Wing Tips

Additional wind-tunnel tests were made of a 1/8-scale model of the Republic XP-91 airplane to determine its characteristics with various modifications. The modifications included a revised conventional tail, revised rocket arrangement, drooped wing tips, and revised landing gear and doors. Tests were also made to determine the effectiveness of the control surfaces of the model with the conventional tail and the effect of changing wing incidence and tail length. The revised rocket arrangement provided a considerable increase in the static directional stability contributed by the vee tail at small angles of yaw. The conventional tail provided a greater static directional stability than the vee tail without increasing the rolling moment due to sideslip. The rolling moment die to sideslip was considerable reduced by either drooped wing tips or open main landing-gear doors. The reduction in rolling moment due to sideslip resulting from the drooped tips was less with the landing-gear doors open than with the doors closed. A change in wing incidence from 0 degrees to 6 degrees reduced the elevator angle required for balance by approximately 6 degrees.

Weiberg, James A.↗
NASA NTRS2001

DARPA/AFRL/NASA Smart Wing Second Wind Tunnel Test Results

To quantify the benefits of smart materials and structures adaptive wing technology, Northrop Grumman Corp. (NGC) built and tested two 16% scale wind tunnel models (a conventional and a "smart" model) of a fighter/attack aircraft under the DARPA/AFRL/NASA Smart Materials and Structures Development - Smart Wing Phase 1. Performance gains quantified included increased pitching moment (C(sub M)), increased rolling moment (C(subl)) and improved pressure distribution. The benefits were obtained for hingeless, contoured trailing edge control surfaces with embedded shape memory alloy (SMA) wires and spanwise wing twist effected by SMA torque tube mechanisms, compared to conventional hinged control surfaces. This paper presents an overview of the results from the second wind tunnel test performed at the NASA Langley Research Center s (LaRC) 16ft Transonic Dynamic Tunnel (TDT) in June 1998. Successful results obtained were: 1) 5 degrees of spanwise twist and 8-12% increase in rolling moment utilizing a single SMA torque tube, 2) 12 degrees of deflection, and 10% increase in rolling moment due to hingeless, contoured aileron, and 3) demonstration of optical techniques for measuring spanwise twist and deflected shape.

Scherer, L. B.↗
NASA NTRS1993

Subsonic aerodynamic characteristics of a proposed advanced manned launch system orbiter configuration

The Advanced Manned Launch System is a proposed near-term technology, two-stage, fully reusable launch system that consists of an unmanned glide-back booster and a manned orbiter. An orbiter model that featured a large fuselage and an aft delta wing with tip fins was tested in the Langley 7- by 10-Foot High-Speed Tunnel. A crew cabin, large payload fairing, and crew access tunnel were mounted on the upper body. The results of the investigation indicated that the configuration was longitudinally stable to an angle of attack of about 6 deg about a center-of-gravity position of 0.7 body length. The model had an untrimmed lift-drag ratio of 6.6, but could not be trimmed at positive lift. The orbiter model was also directionally unstable. The payload fairing was responsible for about half the instability. The tip-fin controllers, which are designed as active controls to produce artificial directional stability, were effective in producing yawing moment, but sizable adverse rolling moment occurred at angles of attack above 6 deg. Differential deflection of the elevon surfaces was effective in producing rolling moment with only small values of adverse yawing moment.

Ware, George M.↗
NASA NTRS2019

Bowles-Tatnall Wake Vortex Encounter Hazard Metric

Wake vortex spacing standards constrict the terminal area throughput and impose severe constraints on the overall capacity and efficiency of the National Airspace System. For more than two decades starting in the early 1990s, the National Aeronautics and Space Administration conducted extensive research on characterizing the formation and evolution of aircraft wakes. This multidisciplinary work included comprehensive field experiments (Pruis et al. 2016), flight tests (Vicroy et al. 1998), and wind tunnel tests (Rossow 1994; Chow et al. 1997). Parametric studies using large eddy simulations (Proctor 1998; Proctor et al. 2006) were conducted in order to develop fast-time models for the prediction of wake transport and decay (Ahmad et al. 2016). Substantial effort was spent on the formulation of acceptable vortex hazard metrics (Tatnall 1995; Hinton and Tatnall 1997). Several wake encounter severity metrics have been suggested in the past, which include the wake circulation strength, vortex-induced rolling moment coefficient (Clv), bank angle, and the roll control ratio (Tatnall 1995; Hinton and Tatnall 1997; Van der Geest 2012). The vortex-induced rolling moment coefficient introduced by Bowles and Tatnall (Tatnall 1995; Gloudemans et al. 2016) has been used extensively for risk and safety analysis of newly proposed air traffic management concepts and procedures. The original method of Bowles and Tatnall assumed a constant wing loading (the wing lift-curve slope, CL is constant), which resulted in an overestimation of the vortexinduced rolling moment coefficient. Bowles (2014) suggested a correction to the original method that provides more accurate values of Clv and which is also consistent with the underlying physics of the problem. The overestimation of Clv in the original method can be corrected by assuming an elliptical lift distribution. Figure 1.1 illustrates the correction in Clv achieved by the modified method.

Joel Malissa↗
NASA NTRS1975

Description and test results of a water basin to determine ground effect in hover using small models

A water basin test facility was established capable of measuring forces and moments of small models of VTOL aircraft, simulating hover in and out of ground effect. Because the models and the operation of the facility are inexpensive, the water basin is particularly suitable for testing the relative characteristics of a great number of model configurations for preliminary design development. Results from a variety of models are given. Lift, pitching moments, and rolling moments are given with and without engine failure simulation in ground effect, and with and without pitched and banked conditions.

Renselaer, D. J.↗