Search NASA⌕ Search

SEARCH · Search NASA

Results for “Realization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Realizing gapped surface states in the magnetic topological insulator Mn Bi 2 - x Sb x Te 4

The interplay between magnetism and nontrivial topology in magnetic topological insulators (MTIs) is expected to give rise to exotic topological quantum phenomena like the quantum anomalous Hall effect and the topological axion states. A key to assessing these novel properties is to realize gapped topological surface sates. MnBi 2 Te 4 possesses nontrivial band topology with an intrinsic antiferromagnetic state. However, the highly electron-doped nature of the MnBi 2 Te 4 crystals obstructs the exhibition of the surface band gap. Here, we tailor the material through Sb substitution to reveal the gapped surface states in MnBi 2-x Sb x Te 4 . By shifting the Fermi level into the bulk band gap, we access the surface states and show a band gap of 50 meV at the Dirac point from quasiparticle interference measured by scanning tunneling microscopy (STM). Surface-dominant conduction is confirmed through transport spectroscopy measured by multiprobe STM below the Néel temperature. The surface band gap is robust against the out-of-plane magnetic field despite the promotion of field-induced ferromagnetism. Finally, the realization of bulk-insulating MTIs with the large exchange gap offers a promising platform for exploring emergent topological phenomena.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Realization of semiconducting layered multiferroic heterojunctions via asymmetrical magnetoelectric coupling

Two-dimensional (2D) semiconducting multiferroics that can effectively couple magnetic and polarization (P) orders have great interest for both fundamental research and technological applications in nanoscale, which are, however, rare in nature. In this work, we propose a general mechanism to realize semiconducting 2D multiferroics via van der Waals (vdW) heterojunction engineering, as demonstrated in a typical heterostructure consisting of magnetic bilayer CrI 3 (bi-CrI 3 ) and ferroelectric monolayer In 2 Se 3 . Interestingly, the novel indirect orbital coupling between Se 4p and Cr 3d orbitals, intermediated by the interfacial I 5p orbitals, is switchable in the opposite P configurations, resulting in an unexpected mechanism of strong asymmetrical magnetoelectric coupling. Therefore, along with the noticeable ferroelectric energy barrier induced by In 2 Se 3 , the realization of opposite magnetic orders in opposite P configurations can eventually result in the novel multiferroicity in bi– CrI 3 /In 2 Se 3 . Finally, we demonstrate that our mechanism can generally be applied to design other vdW multiferroics even with tunable layer thickness.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Experimental realization of classical Z 2 spin liquids in a programmable quantum device

We build and probe a Z 2 spin liquid in a programmable quantum device, the D-Wave DW-2000Q. Specifically, we observe the classical eight-vertex and six-vertex (spin ice) states and transitions between them. To realize this state of matter, we design a Hamiltonian with combinatorial gauge symmetry using only pairwise-qubit interactions and a transverse field, i.e., interactions which are accessible in this quantum device. The combinatorial gauge symmetry remains exact along the full quantum annealing path, landing the system onto the classical eight-vertex model at the endpoint of the path. The output configurations from the device allow us to directly observe the loop structure of the classical model. Moreover, we deform the Hamiltonian so as to vary the weights of the eight vertices and show that we can selectively attain the classical six-vertex (ice) model, or drive the system into a ferromagnetic state. Additionally, we present studies of the classical phase diagram of the system as a function of the eight-vertex deformations and effective temperature, which we control by varying the relative strengths of the programmable couplings, and we show that the experimental results are consistent with theoretical analysis. Finally, we identify additional capabilities that, if added to these devices, would allow us to realize Z 2 quantum spin liquids on which to build topological qubits.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Realization of three- and four-body interactions between momentum states in a cavity

Spin Hamiltonians in condensed matter and quantum sensing typically utilize pairwise or two-body interactions between constituents in the material or ensemble. However, there is growing interest in exploring more general n-body interactions for n > 2. In this study, we realized an effective n = 3-body Hamiltonian interaction using an ensemble of laser-cooled atoms in a high-finesse optical cavity with the pseudospin 1/2 encoded by two atomic momentum states. We applied two dressing tones that induce the atoms to exchange photons via the cavity to realize a virtual six-photon process; lower-order interactions destructively interfered. We also observed signatures of a n = 4-body interaction mediated by a virtual eight-photon process. Our approach may be extensible to three-body interactions in multilevel systems or to even higher-order interactions.

Luo, Chengyi [University of Colorado, Boulder, CO ↗
DOE OSTI2024

Uncertainty Quantification in CO2 Trapping Mechanisms: A Case Study of PUNQ-S3 Reservoir Model Using Representative Geological Realizations and Unsupervised Machine Learning

Evaluating uncertainty in CO2 injection projections often requires numerous high-resolution geological realizations (GRs) which, although effective, are computationally demanding. This study proposes the use of representative geological realizations (RGRs) as an efficient approach to capture the uncertainty range of the full set while reducing computational costs. A predetermined number of RGRs is selected using an integrated unsupervised machine learning (UML) framework, which includes Euclidean distance measurement, multidimensional scaling (MDS), and a deterministic K-means (DK-means) clustering algorithm. In the context of the intricate 3D aquifer CO2 storage model, PUNQ-S3, these algorithms are utilized. The UML methodology selects five RGRs from a pool of 25 possibilities (20% of the total), taking into account the reservoir quality index (RQI) as a static parameter of the reservoir. To determine the credibility of these RGRs, their simulation results are scrutinized through the application of the Kolmogorov–Smirnov (KS) test, which analyzes the distribution of the output. In this assessment, 40 CO2 injection wells cover the entire reservoir alongside the full set. The end-point simulation results indicate that the CO2 structural, residual, and solubility trapping within the RGRs and full set follow the same distribution. Simulating five RGRs alongside the full set of 25 GRs over 200 years, involving 10 years of CO2 injection, reveals consistently similar trapping distribution patterns, with an average value of Dmax of 0.21 remaining lower than Dcritical (0.66). Using this methodology, computational expenses related to scenario testing and development planning for CO2 storage reservoirs in the presence of geological uncertainties can be substantially reduced.

Mahjour, Seyed Kourosh↗
NASA NTRS1972

Feedback in sequential machine realizations.

A method is described for determining the realizability of a sequential machine with trigger or set-reset flip-flop memory elements when the feedback of the machine is given by a Boolean function. Feedbacks in several types of sequential machines with different memory elements are compared, showing the memory specifications allowing the realization of such machines.

Harlow, C. A.↗
NASA NTRS1974

Hardware realization of sampled-data controllers

This paper examines the hardware implementation process for digital controllers (filters), beginning with the desired z-domain transfer function of the digital compensator and ending in the selection of a hardware realization scheme. The final hardware realization is shown to be affected by quantization noise, dynamic range considerations, limit cycles, coefficient roundoff, and filter structure. A design example is included to illustrate the implementation process for a digital rate filter for vehicle control of the space shuttle. This paper develops open-loop techniques which may be extended to the closed-loop case.

Nagle, H. T., Jr.↗
NASA NTRS1980

Realizable optimal control for a remotely piloted research vehicle

The design of a control system using the linear-quadratic regulator (LQR) control law theory for time invariant systems in conjunction with an incremental gradient procedure is presented. The incremental gradient technique reduces the full-state feedback controller design, generated by the LQR algorithm, to a realizable design. With a realizable controller, the feedback gains are based only on the available system outputs instead of being based on the full-state outputs. The design is for a remotely piloted research vehicle (RPRV) stability augmentation system. The design includes methods for accounting for noisy measurements, discrete controls with zero-order-hold outputs, and computational delay errors. Results from simulation studies of the response of the RPRV to a step in the elevator and frequency analysis techniques are included to illustrate these abnormalities and their influence on the controller design.

Dunn, H. J.↗
NASA NTRS1980

Optical communication with two-photon coherent states. III - Quantum measurements realizable with photoemissive detectors

Homodyne detection is shown to achieve the same signal-to-noise ratio as the quantum field quadrature measurement, thus providing a receiver which realizes linear modulation TCS performance gain. The full equivalence of homodyne detection and single-quadrature field measurement is established. A heterodyne configuration which uses a TCS image-band oscillator in addition to the usual coherent state local oscillator is studied. Results are obtained by means of a representation theorem which shows that photoemissive detection realizes the photon flux density measurement.

Yuen, H. P.↗
NASA NTRS1980

Realization theory and quadratic optimal controllers for systems defined over Banach and Frechet algebras

It is noted that recent work by Kamen (1979) on the stability of half-plane digital filters shows that the problem of the existence of a feedback law also arises for other Banach algebras in applications. This situation calls for a realization theory and stabilizability criteria for systems defined over Banach for Frechet algebra A. Such a theory is developed here, with special emphasis placed on the construction of finitely generated realizations, the existence of coprime factorizations for T(s) defined over A, and the solvability of the quadratic optimal control problem and the associated algebraic Riccati equation over A.

Byrnes, C. I.↗
NASA NTRS1985

An Eigensystem Realization Algorithm (ERA) for modal parameter identification and model reduction

A method, called the Eigensystem Realization Algorithm (ERA), is developed for modal parameter identification and model reduction of dynamic systems from test data. A new approach is introduced in conjunction with the singular value decomposition technique to derive the basic formulation of minimum order realization which is an extended version of the Ho-Kalman algorithm. The basic formulation is then transformed into modal space for modal parameter identification. Two accuracy indicators are developed to quantitatively identify the system modes and noise modes. For illustration of the algorithm, examples are shown using simulation data and experimental data for a rectangular grid structure.

Juang, J. N.↗
NASA NTRS1985

An eigensystem realization algorithm for modal parameter identification and model reduction

A method called the eigensystem realization algorithm is developed for modal parameter identification and model reduction of dynamic systems from test data. A new approach is introduced in conjunction with the singular-value decomposition technique to derive the basic formulation of minimum order realization which is an extended version of the Ho-Kalman algorithm. The basic formulation is then transformed into modal space for modal parameter identification. Two accuracy indicators are developed to quantitatively identify the system and noise modes. For illustration of the algorithm, an example is shown using experimental data from the Galileo spacecraft.

Juang, J.-N.↗
NASA NTRS1986

Effects of noise on modal parameters identified by the Eigensystem Realization Algorithm

The basic concept of the Eigensystem Realization Algorithm for modal parameter identification and model reduction is extended to minimize the distortion of the identified parameters caused by noise. The mathematical foundation for the properties of accuracy indicators, such as the singular values of the data matrix and modal amplitude coherence, is provided, based on knowledge of the noise characteristics. These indicators quantitatively discriminate noise from system information and are used to reduce the realized system model to a better approximation of the true model. Monte Carlo Simulations are included to support the analytical studies.

Juang, J.-N.↗
NASA NTRS1986

An Eigensystem Realization Algorithm in Frequency Domain for modal parameter identification

This paper demonstrates the close conceptual relationships between time domain and frequency domain approaches to identification of modal parameters for linear systems. A frequency domain eigensystem realization algorithm, via transfer functions, is developed using a known procedure formulated for a time domain eigensystem realization algorithm, via free decay measurement data. An important feature is the capability of windowing to concentrate analysis on the frequency range of interest. The procedure of overlap averaging is used to produce smoother spectra to reduce the effect of noise on identified modal parameters. Examples from simulation and experiments are given to illustrate the validity of formulations derived in the paper.

Juang, J.-N.↗
NASA NTRS1987

An eigensystem realization algorithm using data correlations (ERA/DC) for modal parameter identification

A modification to the Eigensystem Realization Algorithm (ERA) for modal parameter identification is presented in this paper. The ERA minimum order realization approach using singular value decomposition is combined with the philosophy of the Correlation Fit method in state space form such that response data correlations rather than actual response values are used for modal parameter identification. This new method, the ERA using data correlations (ERA/DC), reduces bias errors due to noise corruption significantly without the need for model overspecification. This method is tested using simulated five-degree-of-freedom system responses corrupted by measurement noise. It is found for this case that, when model overspecification is permitted and a minimum order solution obtained via singular value truncation, the results from the two methods are of similar quality.

Juang, Jer-Nan↗
NASA NTRS1988

Some experiences with the Eigensystem Realization Algorithm

The Eigensystem Realization Algorithm (ERA) is a multiinput/multioutput time-domain algorithm for minimum-order system realization and modal parameter identification. It has been used for structural dynamics data analysis at the Langley Research Center for several years. Some of the practical experiences encountered in these projects are discussed in this paper. Three examples are used: the Galileo spacecraft, the Solar Array Flight Experiment, and a laboratory space-truss model. Several techniques for assessing identification accuracy are illustrated.

Pappa, Richard S.↗
NASA NTRS1988

Confined turbulent fluid-particle flow modeling using multiple-realization particle trajectory schemes

A multiple-realization particle trajectory scheme has been developed and applied to the numerical prediction of confined turbulent fluid-particle flows. The example flows investigated include the vertical pipe upflow experimental data of Tsuji et al. and the experimental data of Leavitt for a coaxial jet flow, comprising a particle-laden central jet and a clean annular jet, into a large recirculation chamber. The results obtained from the numerical scheme agree well with the experimental data, lending confidence to the modeling approach. The multiple-realization particle trajectory turbulent flow modeling scheme is believed to be a more elegant and accurate approach to the extension of single-particle hydrodynamics to dilute multi-particle systems than the more commonly employed two-fluid modeling approach. It is also better able to incorporate additional force items such as lift, virtual mass and Bassett history terms directly into the particle equation of motion as appropriate. This makes it a suitable candidate for particle migration studies and an extension to situations involving liquid particulate phases with possible propulsion applications, such as in spray combustion, follows naturally.

Adeniji-Fashola, A. A.↗
NASA NTRS1988

Realizable feed-element patterns and optimum aperture efficiency in multibeam antenna systems

The results of an earlier paper by Rahmat-Samii et al. (1981), regarding realizable patterns from feed elements that are part of an array that feeds a reflector antenna, are extended. The earlier paper used a cos exp q theta model for the element radiation pattern, whereas here a parametric study is performed, using a model that assumes a central beam of cos exp q theta shape, with a constant sidelobe level outside the central beam. Realizable q-values are constrained by the maximum directivity based on feed element area. The optimum aperture efficiency (excluding array feed network losses) in an array-reflector system is evaluated as a function of element spacing using this model as well as the model of the earlier paper. Experimental data for tapered slot antenna (TSA) arrays are in agreement with the conclusions based on the model.

Yngvesson, K. S.↗