Search NASA⌕ Search

SEARCH · Search NASA

Results for “Redox”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Hypochlorite Redox Chemistry Enables High-Voltage and High-Power Saltwater Batteries

Saltwater batteries (SWBs) are promising alternatives to lithium-ion batteries for large-scale stationary energy storage. However, the performance of conventional oxygen redox-based saltwater battery systems is often constrained by sluggish oxygen evolution and reduction reactions (OER/ORR) at the cathode, leading to low voltage efficiency and limited power density. Here, OER and ORR are replaced by hypochlorite-based redox reactions through the introduction of sodium hypochlorite into saltwater. Operando pH and dissolved oxygen measurements confirm that OER and ORR are minimized and that hypochlorite redox reactions dominate the cathode behavior. Owing to the higher operating potential and faster reaction kinetics, the hypochlorite-redox-based SWBs delivers a higher discharge voltage of 3.3 V and reduced charge-discharge voltage polarization to 0.66 V. Further improvement is achieved by adjusting the saltwater pH to near-neutral conditions, increasing the discharge voltage to 3.5 V and more than doubling the peak power. The hypochlorite redox environment also exhibits chemical stability with key cell components, including the solid electrolyte and cathode current collectors. Operation of series-connected cells and cells employing hard carbon anodes demonstrates scalability and compatibility with alternative anode materials. These results provide a strong foundation for next-generation SWBs targeting large-scale stationary energy storage applications.

Go, Wooseok [ORNL]↗

Spin‐State and Clustering Effects in Fe‐Complex Negolytes for Near‐Neutral Aqueous Redox Flow Batteries

Cost-effective redox-active materials are essential for advancing redox flow batteries (RFBs). Iron, with its abundance and suitability as a redox couple, is a promising candidate; however, achieving stable and fast redox reactions in aqueous RFBs remains a challenge. Here, this study presents an Fe-based negolyte stabilized by a hexadentate ligand, where Fe–ligand bonds are enhanced through intermolecular interactions. The sulfonate-substituted Fe complex exhibits a formal potential of −0.44 V versus Ag/AgCl and an exceptionally high rate constant of 0.69 cm s −1 . Near-neutral RFBs incorporating 0.5 M Fe complex show excellent cycling stability, with no discernible capacity fading over 300 cycles. This performance is attributed to intermolecular hydrogen bonds that reinforce Fe–ligand coordination and promote the formation of stable trimeric clusters. Operando electrochemical Raman spectroscopy and density functional theory reveal that π-backdonation from Fe(II) to the imino-phenolate moiety further stabilizes the complex after reduction. In contrast, the hydroxyl-substituted complex exhibits inferior stability due to weaker hydrogen bonding and less pronounced π-backdonation. These findings underscore the importance of ligand design and intermolecular interactions in developing cost-effective, high-performance redox-active materials for aqueous RFBs.

36 MATERIALS SCIENCE↗

Discovery of a new phase transition and high-valent redox mechanism in Fe-substituted Na 2 Mn 3 O 7

Sodium-ion batteries are a promising lower-cost alternative to lithium-ion batteries, but further improvements in electrochemical performance are required. One strategy to increase capacity is to enable reversible high-valent cationic and anionic redox in layered cathode materials; however, this is typically accompanied by structural degradation. Here, in this study, we elucidate the mechanism by which Fe-doped Na 2 Mn 3 O 7 , featuring ordered transition metal-vacancies, achieves reversible high-valent redox. Using Mössbauer spectroscopy, soft X-ray absorption spectroscopy (XAS), and in-situ hard XAS, we demonstrate reversible high-valent cationic redox involving both Fe and Mn while in-situ Raman confirms the absence of local structural degradation associated with oxygen redox. Combining in-situ X-ray diffraction with theoretical calculations, we further identify a previously unreported global phase transition from the $\bar{P1}$ to the $P2_1/c$ space group during electrochemical cycling and develop a physical model describing this structural evolution. These results provide insights for structurally stable layered sodium transition metal oxide cathodes with reversible high-valent redox.

36 MATERIALS SCIENCE↗

Redox Potentials for Hydrogen Species in Acetonitrile and Tetrahydrofuran

The properties of the fundamental hydrogen species, proton (H+), hydrogen atom (H•), and hydride anion (H-) are critical to a vast range of chemical processes, yet their thermodynamic properties in nonaqueous solvents are not well established. A hybrid supermolecule-continuum approach is used to predict the Gibbs free energies of solvation (?G°solv) and standard redox potentials (E°) for the 2H+/H2 and H•/H- couples in acetonitrile (MeCN) and tetrahydrofuran (THF) following the approach previously used for water. Gas phase geometry optimizations were done using density functional theory (DFT) with the ?B97XD functional, Møller-Plesset second-order perturbation theory (MP2) with augmented correlation-consistent basis sets and composite-correlated molecular orbital theory (G3MP2 and G3MP2B3). Additional single point calculations in gas phase were performed for H- affinity for MeCN and THF at the coupled cluster CCSD(T) level using MP2 geometries. Solvation was included using the self-consistent reaction field SMD model. For H+, the ?G°solv values are predicted to be -252.2 kcal/mol in MeCN and -261.0 kcal/mol in THF. The redox potentials for the 2H+/H2 couple are +0.49 V in MeCN and +0.11 V in THF relative to the aqueous SHE, consistent with the available experimental data. The ?G°solv for H- is predicted to be -80 kcal/mol in MeCN and -68 in THF, and for H•, ?G°solv is predicted to be -1.3 kcal/mol in THF and -2.0 kcal/mol in MeCN. These solvation energies yield respective calculated redox potentials for the H•/H- couple of -0.14 V in MeCN and -0.68 V in THF relative to the aqueous SHE. H2 solvation is slightly exergonic in MeCN (-3.3 kcal/mol) and near thermoneutral in THF (+1.3 kcal/mol). The pKa(H2) is predicted to be 45.4 in MeCN and 47.8 in THF. The proton-coupled electron transfer (PCET) accounting term CG was evaluated giving values on the ferrocene scale within approximately 2 kcal/mol of literature in both solvents. These results provide benchmarks for hydrogen redox chemistry in MeCN and THF and improve consistency across E°, ?G°solv, pKa, and CG. These results provide benchmarks for hydrogen redox chemistry in nonaqueous media challenging previous estimates based on indirect extrapolations and assumptions.

Duda, Damian P.↗

Spatial Heterogenous Redox Couples Degradation in Sodium-Ion Battery Cathode Materials and the Mitigation of Voltage Fade by Blocking Oxygen Release

The use of anionic redox has become a new paradigm for improving the energy density of rechargeable batteries, which is essential for improving the market competitiveness of sodium-ion batteries. However, issues such as voltage attenuation and cycling stability degradation persist in layered oxide anion redox cathode materials. Here, in this study, we systematically investigate the classic Na-ion cathode material Na 0.6 Li 0.2 Mn 0.8 O 2 , and the primary causes of voltage decay are identified as the activation of cations and the reduction in anion redox activity. In addition, the activation of cations is closely associated with anion reactions. Through the application of sophisticated multiscale synchrotron absorption spectroscopy and imaging techniques, we have identified a pronounced pattern of spatially dependent degradation in the evolution of redox couples, which is more evident from the material’s surface to its core. With this understanding, we introduced a surface fluorination approach that modulates the local chemical coordination environment. This strategy increases the formation energy of surface oxygen vacancies and locks transition metals oxide state. Consequently, it enables more reversible anionic redox reactions, which block the spatial progression of degradation and mitigates voltage decay.

25 ENERGY STORAGE↗

Electroanalytical characterization of Np( VI )/Np( V ) redox in a pentadentate ligand environment and stabilization of [Np V O 2 ] + by hydrogen bonding

The redox chemistry of the actinyl cations (AnO 2 n+ ) heavily influences their reactivity and speciation in solution, but the redox properties of the actinyls in non-aqueous media have received far less attention than they deserve. Here, the non-aqueous electrochemistry of a chemically reversible Np(VI)/Np(V) redox manifold is reported in both protic (CH 3 OH) and aprotic (CH 3 CN) organic media. Using a neutral Np(VI) complex supported by a chelating and strongly donating pentadentate ligand that was fully characterized in prior work, a clean Np(VI)/Np(V) redox couple was found to be accessible under ambient conditions. Coupled electrochemical and spectroscopic studies, as well as simulations of cyclic voltammetry data, confirm the 1e− nature of this couple and establish it to be chemically reversible and nearly electrochemically reversible as well. Bulk electrolysis of a solution of the neutral Np(VI) complex facilitated isolation of the corresponding anionic and monomeric Np(V) species. Data from X-ray diffraction analysis as well as optical and vibrational spectroscopies provide strong evidence in support of metal-centered reduction and the Np(V) oxidation state, findings that are in accord with the measured reduction potentials. Distinctive hydrogen bonding interactions between the terminal (yl) oxo groups and water molecules appear to stabilize the isolated Np(V) species in the solid state, providing insight into the features that afford the uncommon chemically reversible redox encountered in this system.

Mikeska, Emily R.↗

Visualizing energy transfer between redox-active colloids

Redox-active colloids (RACs) represent a novel class of energy carriers that exchange electrical energy upon contact. Understanding contact-mediated electron transfer dynamics in RACs offers insights into physical contact events in colloidal suspensions and enables quantification of electrical energy transport in nonconjugated polymers. Redox-based electron transport was directly observed in monolayers of micron-sized RACs containing ethyl-viologen side groups via fluorescence microscopy through an unexpected nonlinear electrofluorochromism that is quantitatively coupled to the redox state of the colloid. Via imaging studies, using this electrofluorochromism, the apparent charge transfer diffusion coefficient D CT of the RAC was easily determined. The visualization of energy transport within suspensions of redox-active colloids was also demonstrated. Our work elucidates fundamental mechanisms of energy transport in colloidal systems, informs the development of next-generation redox flow batteries, and may inspire new designs of smart active soft matter including conductive polymers for applications ranging from electrochemical sensors and organic electronics to colloidal robotics.

Qu, Alan Subing [Univ. of Illinois at Urbana-Champ↗

Geometry, spin coupling, and dielectric control of redox potentials in [4Fe–4S] Clusters

Iron–sulfur (Fe–S) clusters are common biological cofactors that facilitate vital redox reactions. Despite extensive research, the molecular basis of redox potential tuning in ferredoxin-like proteins remains an active area of debate. In this study, we combine statistical analysis of over one thousand [4Fe–4S]-containing protein structures from the Protein Data Bank (PDB) with broken-symmetry and extended broken-symmetry density functional theory to examine how cysteine ligand orientations and environmental screening affect redox properties of the clusters. We identified five main ligand configurations, three of which are predominant in natural structures. Among these, the adiabatic electron affinity differs by less than 0.1 V, indicating that, while geometry plays a secondary role, it allows localized fine-tuning of redox properties. In contrast, electrostatic and solvation effects primarily determine the overall potential range.

Computational Chemistry↗

Dissolved Oxygen Redox as the Source of Hydrogen Peroxide and Hydroxyl Radical in Sonicated Emulsive Water Microdroplets

Sonicated emulsive water microdroplets (SEWMs) accelerate and enable a variety of catalyst-free chemical transformations. However, significant unanswered questions remain regarding the chemical intermediates they form and their possible redox origin. In this study, we identified dissolved O 2 as the primary originator of reactive oxygen species (ROS) such as OH• and H 2 O 2. We uncovered the role of dissolved O 2 redox by using a combination of microelectrochemical methods to detect H 2 O 2 , isotopic methods to identify the source of H 2 O 2 , and a combination of electron spin resonance and the DMPO spin trap to detect radicals such as OH•. Notably, we found that H 2 O 2 production is correlated with O 2 content via a reduction pathway enabled by a sufficiently large reducing power that can additionally generate H 2 and even perform Pb electroless deposition on Au and Cu metal substrates. Building on our findings, continuous O 2 bubbling of SEWMs showed accumulation of H 2 O 2 up to ∼88 mM in the aqueous phase within 1 h of sonication, demonstrating the scale-up promise of this method. Distinct to sonochemistry of a single phase, this study advances our understanding of the confluence of redox and chemical reaction mechanisms within SEWMs as a biphasic system. This insight paves the way for improving their reaction kinetics, yield, and selectivity, positioning these attractive redox microreactors as alternatives to traditional electrolyzers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Oxadiazole derivatives as stable anolytes for >3 V non-aqueous redox flow battery

Effective utilization of energy from renewable sources such as wind and solar requires the development of long duration energy storage (LDES) systems that can accommodate intermittent energy accrual. One option under investigation is the use of a redox flow battery (RFB). A significant amount of work has explored aqueous RFB systems with a variety of inorganic and organic carriers. However, moving to a nonaqueous solvent such as acetonitrile (MeCN) for RFB provides a much larger electrochemical window, which could lead to increased energy density if properly utilized. Here, in this work, we investigate a series of 2,5-diphenyl-1,3,4-oxadiazole (DiPhenOx) derivatives as anolytes for a redox flow battery. DiPhenOx has a low voltage redox event that, while reversible by cyclic voltammetry, was determined to be irreversible during bulk electrolysis. To improve cycling performance, we introduced various ester and cyano groups to the phenyl rings of DiPhenOx using molecular engineering. We characterized these derivatives spectroscopically and electrochemically to assess their feasibility for flow battery applications. The ester derivatives with the best cycling performance were tested in a flow cell vs. ferrocene, 2,5-di-tert-butyl-1,4-bis(2-methoxyethoxy)benzene (DBBB) and thianthrene, which resulted in ~2 V, ~3 V and ~3 V redox flow batteries, respectively.

25 ENERGY STORAGE↗

Modulating Surface Anionic Redox Chemistry toward Highly Stable Li-Rich Cathodes with Negligible Oxygen Loss

Low initial Coulombic efficiency and severe capacity/voltage fading during cycling caused by serious irreversible oxygen release, especially in the initial cycle, and resultantly induced unstable electrode/electrolyte interfacial chemistry, largely prohibit the commercial application of high-capacity Li-rich layered oxide cathodes (LLOs). Here, in this work, a dual reductive gas interface cotreatment strategy is applied to regulate the lattice oxygen redox activity and reversibility with a multiple defective structure design including Li/O/TM (TM = transition metal) vacancies and the intrinsic TM doping as well as a full-surface protective layer, which can suppress the irreversible TM migration and then undesirable phase transformation, resisting the corrosion of electrolyte during cycling effectively. Importantly, the introduced reversible SO 3 2- /SO 4 2- redox couple that provides extra capacity compensation could alleviate the distortion of oxygen-central octahedral structure and structural collapse caused by immoderate oxygen oxidation. Thus, the lattice oxygen redox chemistry is optimized, with negligible oxygen loss during the initial cycle. And the designed AS-LLO cathode with greatly enhanced structure stability shows high-capacity retentions of 99.2% at 0.3C after 100 cycles and 82.4% even after 1000 cycles at 5C. This work provides a guideline for manipulating the oxygen redox chemistry to achieve long-lifespan Li-rich layered oxide cathodes for high-energy-density lithium batteries.

25 ENERGY STORAGE↗

A redox-reversible A/B-site co-doped BaFeO 3 electrode for direct hydrocarbon solid oxide fuel cells

Solid oxide fuel cells (SOFCs) can directly convert the chemical energy in fuel to electrical energy with fuel flexibility; however, the conventional nickel-based anodes face great challenges due to coking upon direct oxidation of hydrocarbon fuels and redox instability. Thus, developing new anode materials which can provide high coking resistance as well as redox stability is crucial. In this work, Ba 0.6 La 0.4 Fe 0.8 Mo 0.1 Ni 0.1 O 3-δ (BLFMN) has been synthesized in air using a sol–gel combustion method, resulting in a dual phase consisting of a cubic BLFMN main phase and scheelite BaMoO 4 (BMO 4 ) secondary phase. By heat-treating the BLFMN dual phase in H 2 at 800 °C for 5 h, a metallic nanoparticle-decorated BLFMN triple phase compound comprising cubic BLFMN, cubic BaMoO 3 (BMO 3 ) and in situ exsolved FeNi 3 alloy was obtained. BLFMN was subsequently investigated as an electrode material for La 0.8 Sr 0.2 Ga 0.83 Mg 0.17 O 3-δ (LSGM) electrolyte (300 μm) supported SOFCs. Symmetrical cells using BLFMN as electrodes with the cell configuration of BLFMN//LSGM//BLFMN showed excellent redox reversibility and a peak power density (PPD) of 1.32 W cm -2 at 850 °C when using H 2 as fuel. Single cell with the cell configuration of BLFMN//LSGM//LSCF (La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ ) reached PPD of 1.61 and 0.41 W cm -2 at 850 °C when operating with H 2 and CH 4 fuel, respectively. Moreover, the single cell exhibit excellent stability (over 300 h) upon direct oxidation of hydrocarbon fuels of CH 4 and C 3 H 8 . This study indicates that BLFMN is a promising redox reversible and coking resistant anode for SOFCs.

08 HYDROGEN↗

Oscillatory redox behavior in oxides: Cyclic surface reconstruction and reactivity modulation via the Mars–van Krevelen mechanism

The breaking of translational symmetry at oxide surfaces gives rise to coordinatively unsaturated cations/anions and surface restructuring—key factors that govern surface reactivity. Using direct in situ environmental transmission electron microscopy (TEM) observations along with atomistic modeling, we report oscillatory redox behavior in CuO under H 2 , where cyclic surface reconstruction and reactivity modulation occur via the Mars–van Krevelen (MvK) mechanism. We observe self-switching between oxygen-rich and oxygen-deficient surface reconstructions, alternately activating and deactivating the surface for H 2 O formation. During periods of chemical inactivity, the oxygen-deficient surface undergoes slow reoxidation via lattice oxygen diffusing from subsurface and bulk reservoirs, restoring the active oxygen-rich surface termination. The inherent disparity in chemical activity among undercoordinated surface ions, along with sluggish subsurface-to-surface oxygen replenishment, drives this oscillatory redox cycle, modulating H2-induced loss of lattice oxygen at the surface and its delayed replenishment from the subsurface. This creates spatiotemporally separated redox steps at the oxide surface. The phenomena and atomistic insights presented here have significant implications for manipulating the surface reactivity of oxides by tuning the separation of these redox steps.

36 MATERIALS SCIENCE↗

Nitrogen limitation causes a seismic shift in redox state and phosphorylation of proteins implicated in carbon flux and lipidome remodeling in Rhodotorula toruloides

Background: Oleaginous yeast are prodigious producers of oleochemicals, offering alternative and secure sources for applications in foodstuff, skincare, biofuels, and bioplastics. Nitrogen starvation is the primary strategy used to induce oil accumulation in oleaginous yeast as part of a global stress response. While research has demonstrated that post-translational modifications (PTMs), including phosphorylation and protein cysteine thiol oxidation (redox PTMs), are involved in signaling pathways that regulate stress responses in metazoa and algae, their role in oleaginous yeast remain understudied and unexplored. Results: Towards linking the yeast oleaginous phenotype to protein function, we integrated lipidomics, redox proteomics, and phosphoproteomics to investigate Rhodotorula toruloides under nitrogen-rich and starved conditions over time. Our lipidomics results unearthed interactions involving sphingolipids and cardiolipins with ER stress and mitophagy. Our redox and phosphoproteomics data highlighted the roles of the AMPK, TOR, and calcium signaling pathways in regulation of lipogenesis, autophagy, and oxidative stress response. As a first, we also demonstrated that lipogenic enzymes including fatty acid synthase are modified as a consequence of shifts in cellular redox states due to nutrient availability. Conclusions: We conclude that lipid accumulation is largely a consequence of carbon rerouting and autophagy governed by changes to PTMs, and not increases in the abundance of enzymes involved in central carbon metabolism and fatty acid biosynthesis. Our systems-level approach sets the stage for acquiring multidimensional data sets for protein structural modeling and predicting the functional relevance of PTMs using Artificial Intelligence/Machine Learning (AI/ML). Coupled to those bioinformatics approaches, the putative PTM switches that we delineate will enable advanced metabolic engineering strategies to decouple lipid accumulation from nitrogen limitation.

Lipid Signalling↗

Predicting Radiation-Induced Plutonium Redox Chemistry using Multi-scale Modeling Methods

Over the the last 70 years plutonium (Pu) has been integral in the development of several technologies that have changed the world, yet our fundamental understanding of its chemistry is still far from complete. This is a testament to this element’s unique and complex properties, such as its ability to coexist as multiple oxidation states in aqueous solution. Careful manipulation of plutonium oxidation states is essential in the study and utilization of its rich chemistry. To achieve this level of control, a comprehensive mechanistic understanding of radiation-induced plutonium redox chemistry is critical due to the unavoidable exposure of plutonium to ionizing radiation fields, both inherent and from in-process applications. For this reason, we have developed an experimentally evaluated multi-scale computer model for the prediction of gamma radiation-induced Pu(IV) redox chemistry in concentrated nitric acid solutions (1.0, 3.0, and 6.0 M). Under these acidic, aqueous solution conditions, cobalt-60 gamma irradiation afforded negligible net change in the steady-state oxidation state distribution of Pu(IV). Multi-scale calculations, which are in excellent agreement with experimental data, indicate that this observation is due to radiation-induced redox cycling between Pu(IV) and Pu(III), as achieved by the reduction of Pu(IV) by radiolytic nitrous acid and hydrogen peroxide, and the oxidation of Pu(III) by nitrate and hydroxyl radicals. These radiation-induced redox processes are augmented by plutonium’s inherent disproportionation reactions.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Phloroglucinol–2,6‐Diaminoanthraquinone as a Durable Redox Mediator for Enhancing Conversion Reaction Kinetics in Lithium‐Sulfur Batteries

Abstract Lithium‐sulfur batteries, despite being a promising solution for next‐generation secondary batteries, require substantial efforts to overcome the challenges of sluggish sulfur redox kinetics, polysulfides shuttling, and Li metal instability before achieving practical viability. Conventional strategies that utilize metal catalysts or soluble redox mediators (RMs) are limited by either impractical producing processes or unsatisfactory service life. Herein, an electrochemically active organic material, phloroglucinol – 2,6‐diaminoanthraquinone (PG‐DAAQ) is synthesized through a green and facile polymerization process to better resolve these issues. Serving as an RM at the cathode, PG‐DAAQ exhibits enduring redox activity within the sulfur operating potential window, leading to enhanced redox kinetics and sulfur utilization. Remarkably, even without any metal elements, PG‐DAAQ exhibits an excellent affinity to polysulfides, thereby suppressing the shuttling and facilitating the formation of a more favorable solid‐electrolyte interface to stabilize Li deposition at the anode. As a result, Li‐S cells employing PG‐DAAQ show significantly enhanced cycling and rate performances than the control cells. Even with a low electrolyte‐to‐sulfur ratio of 6, pouch cells with PG‐DAAQ deliver a reversible discharge capacity of 821 mA h g −1 after 100 cycles at a C/10 rate.

Lai, Tianxing↗

Temporal Patterns in Soil Redox Potential Vary Across a Freshwater Coastal Delta

Widespread and persistent flooding is submerging coastal ecosystems, particularly along the Louisiana Gulf coast, where flooding results from the compounding effects of ground subsidence and rising sea level. Restoration projects aim to mitigate land loss by diverting sediment loads from rivers into degraded areas to increase ground elevation. To predict how coastal ecosystems will change over time in response to projected changes in relative sea level and restoration, it is necessary to understand how subsurface biogeochemical processes respond to dynamic hydrologic forcings. Here, this study evaluates how environmental parameters that integrate biogeochemical processes vary with water table fluctuations in the freshwater Wax Lake Delta (WLD) in Louisiana, USA, where water diversions have formed one of the only active deltas along the coast. High‐frequency observations of water level, soil redox potential, specific conductance and pH were made for 1 year along elevation transects located on the older, proximal and younger, distal ends of a deltaic island. Redox responded rapidly to changing water tables, with fluctuations occurring primarily in shallow soils (< 20 cm) and at higher elevations. Deeper soils and those at lower elevation remained inundated and reduced. Semi‐diurnal tidal fluctuations were pronounced in younger, distal soils, presumably due to rapid groundwater exchange with the river channel. Tidal signals were muted in older soils that instead exhibited seasonal variability associated with river discharge and evapotranspiration. Although much of the delta sediments are persistently reducing and anoxic, redox fluctuations in the natural levees that border the deltaic islands likely drive high rates of biogeochemical activity. Evaluating how hydrology drives the frequency and duration of redox fluctuations provides a basis for understanding how biogeochemical processes might vary with complex hydrological interactions in coastal systems.

Herndon, Elizabeth [Oak Ridge National Laboratory ↗

Short-Term Groundwater Level Fluctuations Drive Subsurface Redox Variability

As global change processes modify the extent and functions of terrestrial-aquatic interfaces, the variability of critical and dynamic transitional zones between wetlands and uplands increases. However, it is still unclear how fluctuating water levels at these dynamic boundaries alter groundwater biogeochemical cycling. Here, we used high-temporal resolution data along gradients from wetlands to uplands and during fluctuating water levels at freshwater coastal areas to capture spatiotemporal patterns of groundwater redox potential (E h ). We observed that topography influences groundwater E h that is higher in uplands than wetlands; however, the high variability within TAI zones challenged the establishment of distinct redox zonation. Declining water levels generally decreased E h , but most locations exhibited significant E h variability, which is associated with rare instances of short-term water level fluctuations introducing oxygen. The E h -oxygen relationship showed distinct hysteresis patterns, reflecting redox poising capacity at higher E h , maintaining more oxidizing states longer than dissolved oxygen presence. Surprisingly, we observed more frequent oxidizing states in transitional areas and wetlands than in uplands. We infer that occasional oxygen entering specific wetland-upland boundaries acts as critical biogeochemical control points. Finally, high-resolution data can capture such rare yet significant biogeochemical instances, supporting redox-informed models and advancing the predictability of climate change feedback.

54 ENVIRONMENTAL SCIENCES↗