Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rheometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Microscopic dynamics of stress relaxation in a nanocolloidal soft glass

Here, we report x-ray photon correlation spectroscopy (XPCS) experiments with in situ rheometry performed on a soft glass composed of a concentrated suspension of charged silica nanoparticles subjected to step strains that induce yielding and flow. The XPCS measurements characterize the particle-scale and mesoscale motions within the glass that underlie the highly protracted decay of the macroscopic stress following the step strains. These dynamics are anisotropic, with slow, convective particle motion along the direction of the preceding shear that persists for surprisingly large times and that is accompanied by intermittent motion in the perpendicular (vorticity) direction. A close correspondence between the convective dynamics and stress relaxation is demonstrated by power-law scaling between the characteristic velocity of the collective particle motion and the rate of stress decay.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructural and rheological training and memory of nanocolloidal soft glasses under cyclic shear

An intrinsic feature of disordered and out-of-equilibrium materials, such as glasses, is the dependence of their properties on their history. An important example is rheological memory, in which disordered solids obtain properties based on their deformation history. Here, in this study, we employ x-ray photon correlation spectroscopy with in situ rheometry to characterize memory formation in a nanocolloidal soft glass due to cyclic shear. During a cycle, particles undergo irreversible displacements composed of a combination of shear-induced diffusion and heterogeneous, residual strain fields. At lower shear amplitudes, the displacements resemble a random walk in which the directions in each cycle are independent of those in preceding cycles, while at high amplitude, the irreversible displacements in consecutive cycles become correlated. The magnitudes of the displacements decrease with each cycle before reaching a steady state where the microstructure has been trained to achieve enhanced reversibility even at shear amplitudes well above yielding and despite the presence of thermal fluctuations. At amplitudes below and near yielding, these decreases are monotonic, while well above yielding, they are nonmonotonic, suggesting evidence of shear banding. Accompanying this microstructural training are corresponding decreases in the dissipation during each cycle and the magnitude of the residual stress toward steady-state values. Memory of the training is revealed by measurements in which the amplitude of the shear is changed after steady state is reached. The magnitude of the particle displacements, as well as the dissipation and the change in residual stress, vary nonmonotonically with the new shear amplitude, having minima near the training amplitude, thereby revealing correlated microscopic and macroscopic signatures of memory.

Chen, Yihao [Johns Hopkins Univ., Baltimore, MD (U↗
DOE OSTI2018

Rheology of simulated radioactive waste slurry and cold cap during vitrification

During the vitrification of radioactive waste in a Joule-heated melter, aqueous melter feed slurry forms a cold cap, a reacting and melting material, which floats on the surface of the molten glass. The rheological behavior of the feed affects cold cap formation and shape, and is vital for modeling the feed-to-melt conversion process. Here, we used slurry feed simulant and fast-dried slurry solids representing the cold cap to investigate the rheological behavior of the feed as it transforms into glass. Both low-temperature and high-temperature rheometry were performed and a new scheme was applied to estimate the feed viscosity. This study shows that the conversion advances in four sequential stages that form distinct regions in the cold cap: (i) a fast-spreading boiling slurry from which water evaporates, (ii) a porous solid region (viscosity > 10 8 Pa s) containing reacting solids and molten salts, (iii) a plastic region in which glass-forming melt connects the refractory solids (~10 8 to ~10 6 Pa s), and (iv) a viscous foam layer in which the viscosity drops from ~10 5 to ~10 1 Pa s. The implications for the mathematical modeling of the cold cap are discussed.

glass melting↗
DOE OSTI2025

Highly functional microspheres facilitating Diels–Alder network formation

Introducing particles to dynamic covalent networks is a common approach to improve their performance. However, network formation can be impacted by their size and functionality. The influence can be predicted by common theories for small molecular precursors, but it is unclear whether they are applicable to precursors bearing numerous reactive groups and micrometer-scale dimensions. In this work, an experimental study was undertaken using dynamic covalent networks formed by the Diels–Alder reaction between furan and maleimide groups. The gelation behavior of the Diels–Alder networks was studied using rheometry to track their network formation at 40 °C with varying maleimide-functionalized microsphere loading. The highly functional microspheres can interact with the furan precursor, aiding in the formation of the Diels–Alder networks. A 5 wt% microsphere sample can reduce the gelation time by 23% and facilitate network formation in an unbalanced stoichiometry near the critical composition to form a percolating network.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Linear viscoelastic measurements of commerical therapy putties for design and intuition

This dataset complements the publication Mapping Linear Viscoelasticity for Design and Tactile Intuition (Corman & Ewoldt, 2019). It contains rigorous shear rheometry measurements for six commercial silicone putties, including creep recovery, SAOS, LAOS, and stress relaxation. Additional, unpublished data was generated as part of a graduate rheology course taught by Randy Ewoldt at University of Illinois Urbana-Champaign. Together, these datasets provide a comprehensive example of linear viscoelasticity of a commercial material. The collection is intended both as a pedagogical resource for developing physical intuition in linear viscoelasticity and as a reference dataset for data interpretation, model fitting, and comparative rheological analysis.

C. Marsh, Maxwell↗
DOE OSTI2024

A versatile approach to stabilize liquid-liquid interfaces using surfactant self-assembly

Stabilizing liquid–liquid interfaces, whether between miscible or immiscible liquids, is crucial for a wide range of applications, including energy storage, microreactors, and biomimetic structures. In this study, a versatile approach for stabilizing the water-oil interface is presented using the morphological transitions that occur during the self-assembly of anionic, cationic, and nonionic surfactants mixed with fatty acid oils. The morphological transitions underlying this approach are characterized and extensively studied through small-angle X-ray scattering (SAXS), rheometry, and microscopy techniques. Dissipative particle dynamics (DPD) as a simulation tool is adopted to investigate these morphological transitions both in the equilibrium ternary system as well as in the dynamic condition of the water-oil interface. Such a versatile strategy holds promise for enhancing applications such as liquid-in-liquid 3D printing. Moreover, it has the potential to revolutionize a wide range of fields where stabilizing liquid–liquid interfaces not only offers unprecedented opportunities for fine-tuning nanostructural morphologies but also imparts interesting practical features to the resulting liquid shapes. These features include perfusion capabilities, self-healing, and porosity, which could have significant implications for various industries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

The mechanical properties of Kel-F 800 (FK-800) as a function of crystallinity

Kel-F 800 is a copolymer of chlorotrifluoroethylene PTFE (75 wt. %) and vinylidene fluoride PVDF (25 wt. %). It has previously been used as a PBX binder for insensitive explosives such as PBX 9502 and LX-17. 3M started production of Kel-F 800 in 1957 and small-scale batches continued to be made until 2002 when production ceased due to environmental concerns regarding one of the emulsifiers used during production. Around 2000 the Kel-F 800 name was changed to FK-800 to avoid trademark concerns because rights to produce another polymer with a similar tradename (Kel-F 81) had been sold to another manufacturer. The Kel designation came from the original manufacturer of PCTFE (Kel-F 81), the Kellog company. To avoid confusion this document will only refer to Kel-F 800. In 2006, production of small-scale batches of Kel-F 800 was started again by 3M in response to customer enquiries. This new material, the first blended batch is referred to as LOT 1, was produced with a different emulsifier than used previously. Because Kel-F 800 is made in a small batch reactor, considerable variation in crystallinity can be expected from lot to lot and year to year. In many ways, this is not significant since the material is dissolved in a solvent (often MEK, ethylmethyl ketone or ethyl acetate) for PBX production purposes. This destroys the as received crystallinity and the resulting crystallinity in the processed material is a function of polymer molecular weight and thermal history. Producing large billets of Kel-F 800 from solvent extraction is not practical and so a compression molding technique has been used above the melting temperature. This method also removes residual crystallinity from the supplied granules. The molecular weight of a polymer can be estimated by several techniques, the most common being gel permittivity chromatography (GPC), size exclusion chromatography (SEC) and shear rheometry measurements of polymer/solvent solutions. Changes in molecular weight will affect the crystallization rate and the maximum crystallinity reached for a specific thermal history. Both references agree that the new LOT 1 material molecular weight falls within the deviation found from averaging previous historical lots of Kel-F 800.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Filament Formation and Melt Spinning of Coal-Based Mesophase Pitch for Carbon Fiber Production

High-performance carbon fibers excel as high specific strength and modulus materials, and are utilized in composites applications ranging across aerospace, automotive, energy, infrastructure, and sports equipment sectors. Compared to PAN-based carbon fiber, mesophase pitch-based carbon fiber has lower tensile strength but provides a higher modulus, higher thermal conductivity, and a lower cost potential. However, challenges in stable, continuous melt spinning processing are a serious limiting factor. Unlike typical melt spinning of long, linear chain polymers, mesophase pitch is a comprised of relatively shorter polycyclic aromatic hydrocarbons which form a liquid crystal. In its ‘green’ or ‘as-spun’ state, the fibers are very fragile. Moreover, its temperature of processing is quite high, often approaching 400ºC. Complex flow dynamics combined with short length and time scale heat transfer render its melt spinning a formidable processing challenge. Improved understanding of the root causes for nascent filament breakage and spinning instabilities are needed. This work aims to determine fundamental phenomena that govern mesophase pitch filament formation by comparison of required draw force and uninterrupted spinning minutes with applied draw down ratio. The effect of perturbations on spinning stability are analyzed using capillary rheometry, microscopy of elongating filaments, and filtration.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Exploring New Applications of Municipal Solid Waste

This study aimed to (i) characterize municipal solid waste (MSW) sourced from Utah and Michigan transfer stations and (ii) upcycle, produce, and evaluate composites derived from this MSW. Composition analysis showed that the MSW was composed of a variety of commodity plastics, paper/cardboard, and inorganic materials. Detailed chemical analysis for lignin, cellulose, hemicellulose, and lipids was performed. The plastics identified were mainly polyethylene, polypropylene, polystyrene, and poly (ethylene terephthalate). The compoundability of the MSW was assessed by torque rheometry. Composites were prepared by compounding the MSW in an extruder. A composite flexural strength of 29 MPa and a modulus of 1.0 GPa was achieved. The thermal properties of the composites were also determined. The melt flow behavior of the MSW composites at 190 °C was comparable to wood plastic composite formulations.

characterization↗
NASA NTRS1987

Polyimide processing additives

A method has been found for enhancing the melt flow of thermoplastic polyimides during processing. A high molecular weight 422 copoly(amic acid) or copolyimide was fused with approximately 0.05 to 5 pct by weight of a low molecular weight amic acid or imide additive, and this melt was studied by capillary rheometry. Excellent flow and improved composite properties on graphite resulted from the addition of a PMDA-aniline additive to LARC-TPI. Solution viscosity studies imply that amic acid additives temporarily lower molecular weight and, hence, enlarge the processing window. Thus, compositions containing the additive have a lower melt viscosity for a longer time than those unmodified.

Pratt, J. R.↗
NASA NTRS1992

Polyimide processing additives

A process for preparing polyimides having enhanced melt flow properties is described. The process consists of heating a mixture of a high molecular weight poly-(amic acid) or polyimide with a low molecular weight amic acid or imide additive in the range of 0.05 to 15 percent by weight of additive. The polyimide powders so obtained show improved processability, as evidenced by lower melt viscosity by capillary rheometry. Likewise, films prepared from mixtures of polymers with additives show improved processability with earlier onset of stretching by TMA.

Fletcher, James C.↗
NASA NTRS1993

Polyimide processing additives

A process for preparing polyimides having enhanced melt flow properties is described. The process consists of heating a mixture of a high molecular weight poly-(amic acid) or polyimide with a low molecular weight amic acid or imide additive in the range of 0.05 to 15 percent by weight of the additive. The polyimide powders so obtained show improved processability, as evidenced by lower melt viscosity by capillary rheometry. Likewise, films prepared from mixtures of polymers with additives show improved processability with earlier onset of stretching by TMA.

Pratt, J. Richard↗
NASA NTRS1998

Filler/ Polycarbosilane Systems as CMC Matrix Precursors

Pyrolytic conversion of polymeric precursors to ceramics is accompanied by loss of volatiles and large volume changes. Infiltration of a low viscosity polymer into a fiber preform will fill small spaces within fiber tows by capillary forces, but create large matrix cracks within large, intertow areas. One approach to minimizing shrinkage and reducing the number of required infiltration cycles is to use particulate fillers. In this study, Starfire allylhydridopolycarbosilane (AHPCS) was blended with a silicon carbide powder, with and without dispersant, using shear mixing. The polymer and polymer/particle interactions were characterized using nuclear magnetic resonance, differential scanning calorimetry, thermogravimetric analysis and rheometry. Polymer/particulate slurries and suspensions were used to infiltrate a figidized preform of an eight ply five harness satin CG Nicalon fiber having a dual layer BN/SiC interface coating, and the resulting composites characterized by optical and scanning electron microscopy.

Hurwitz, Frances I.↗
NASA NTRS2010

Out-Life Characteristics of IM7/977-3 Composites

The capability to manufacture large structures leads to weight savings and reduced risk relative to joining smaller components. However, manufacture of increasingly large composite components is pushing the out-time limits of epoxy/ carbon fiber prepreg. IM7/977-3 is an autoclave processable prepreg material, commonly used in aerospace structures. The out-time limit is reported as 30 days by the manufacturer. The purpose of this work was to evaluate the material processability and composite properties of 977-3 resin and IM7/977-3 prepreg that had been aged at room temperature for up to 60 days. The effects of room temperature aging on the thermal and visco-elastic properties of the materials were investigated. Neat resin was evaluated by differential scanning calorimetry to characterize thermal properties and change in activation energy of cure. Neat resin was also evaluated by rheometry to characterize its processability in composite fabrication. IM7/977-3 prepreg was evaluated by dynamic mechanical analysis to characterize the curing behavior. Prepreg tack was also evaluated over 60 days. The overall test results suggested that IM7/977-3 was a robust material that offered quality laminates throughout this aging process when processed by autoclave.

Miller, Sandi G.↗
DOE OSTI2020

Chemical structure and curing dynamics of bisphenol S, PEEK™-like, and resveratrol phthalonitrile thermoset resins

This effort provides a multifaceted analysis of the structural changes and material dynamics of thermally driven softening and curing of three distinct phthalonitrile (PN) resins that cross-link into thermally stable and oxidation-resistant thermosets. Although this material system has yielded a large subset of fire-retardant composites that require facile processing and low-temperature curing, to date, insufficient information had been available on the fundamental processes that drive their softening and curing stages. Our approach conducted a complementary analysis the chemistry, monomer mobility, and rheology of three PN polymers in order to correlate the curing processes with corresponding structural and behavioral transformations of thermosets. Here, we focused on PNs with a bisphenol S backbone, a bisphenol A (PEEK™-like) backbone, and a resveratrol backbone. We relied on quasi-elastic neutron scattering (QENS) in order to analyze the in situ dynamics and self-diffusion properties of PN monomers, and to track changes in their mobilities during cross-linking and staging. Our analysis facilitates proper control over the staging and final curing of these resins and enables more efficient processing of these thermosets.

36 MATERIALS SCIENCE↗
DOE OSTI2021

New strategy for liquefying corn stover pellets

The movement of solid material into and between unit operations within a biorefinery is a bottleneck in reaching design capacity, with formation of biomass slurries needed to introduce feedstock. Corn stover slurries have been achieved from dilute acid, pretreated materials resulting in slurry concentrations of up to about 150 g/L, above which flowability is compromised. We report a new strategy to liquefy corn stover at higher solids concentration (300 g/L) by initially cooking it with the enzyme mimetic maleic acid at 40 mM and 150°C. This is followed by 6 h of enzymatic modification at 1 FPU (2.2 mg protein)/g solids, resulting in a yield stress of 171 Pa after 6 h and 58 Pa in 48 h compared to 6806 Pa for untreated stover. Mimetic treatment of corn stover pellets minimizes the inhibitory effect of xylo-oligomers on hydrolytic enzymes. Furthermore, this strategy allows for the delivery of solid lignocellulosic slurry into a pretreatment reactor by pumping, improving operability of a biorefinery.

09 BIOMASS FUELS↗
DOE OSTI2024

Protorheology in practice: Avoiding misinterpretation

Protorheology is the paradigm that any observed flow or deformation is a chance to infer quantitative rheological properties. While this creates many opportunities for insight, there is significant risk of misunderstanding the physics involved, e.g. misinterpreting a liquid as a solid or mistaking viscous flow time as viscoelastic relaxation time. We describe these and other potential mistakes, use case studies to show how serious the problems can be, and contrast misinterpretations with correct approaches and interpretations. Some issues are especially important with materials involving colloidal particles and flows involving surface tension. Whether the reader is making inference from a tilted vial, time-lapse gravity-driven flow, a bounce test, die swell, or any other protorheology observation, the examples here serve as a guide for avoiding bad data in protorheology.

42 ENGINEERING↗
DOE OSTI2023

Memory in aging colloidal gels with time-varying attraction

Here, we report a combined rheology, x-ray photon correlation spectroscopy, and modeling study of gel formation and aging in suspensions of nanocolloidal spheres with volume fractions of 0.20 and 0.43 and with a short-range attraction whose strength is tuned by changing temperature. Following a quench from high temperature, where the colloids are essentially hard spheres, to a temperature below the gel point, the suspensions form gels that undergo aging characterized by a steadily increasing elastic shear modulus and slowing, increasingly constrained microscopic dynamics. The aging proceeds at a faster rate for stronger attraction strength. When the attraction strength is suddenly lowered during aging, the gel properties evolve non-monotonically in a manner resembling the Kovacs effect in glasses, in which the modulus decreases and the microscopic dynamics become less constrained for a period before more conventional aging resumes. Eventually, the properties of the gel following the decrease in attraction strength converge to those of a gel that has undergone aging at the lower attraction strength throughout. The time scale of this convergence increases as a power law with the age at which the attraction strength is decreased and decreases exponentially with the magnitude of the change in attraction. A model for gel aging in which particles attach and detach from the gel at rates that depend on their contact number reproduces these trends and reveals that the non-monotonic behavior results from the dispersion in the rates that the populations of particles with different contact number adjust to the new attraction strength.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗